flashrom May 2012

flashrom@flashrom.org

42 participants
127 discussions

Marvell 9120 SATA Controller/Macronix MX25L4005 EEPROM on ASUS P7p55D-E LX
by Richard R. Blum 25 May '12

25 May '12

Dear Flashrom Support: I recently bricked the Marvell 9120 SATA Controller on an ASUS P7P55D-E LX mainboard. I have read that I may be able to recover this controller by flashing the external Macronix MX25L4005 EEPROM on which the Marvell 9120 firmware is stored using flashrom. When I ran flashrom on the ASUS P7P55D-E LX mainboard, flashrom returned the warnings associated with laptops, so I didn't run flashrom further. It appears that flashrom fully supports the Macronix MX25L4005 EEPROM and I have a copy of an image of the original firmware. Also, it is my understanding that the ASUS P7P55D-E LX southbridge is an Intel ICH10R. Is it possible to flash the Macronix MX25L4005 EEPROM without removing the chip? If so, please provide recommendations and instructions. If not, I read about a flashrom user who flashed a Macronix MX25L4005 to restore a laptop using a buspirate and disconnecting the VCC pin. Thanks for your help. Richard Blum

2 2

external programmer
by Bicks Factory 24 May '12

24 May '12

Trying to use an external programmer, specifically the TIAO/DIYGADGET USB Multi-Protocol Adapter (TUMPA). Running from a live cd of parted magic. Using flashrom v0.9.5.2-r1515. Run command: flashrom -p ft2232_spi:type=tumpa get back: unknown programmer ft2232_spi:type=tumpa. Motherboard is a MSI G41M-F. Flashrom can see the flash chip on the board. Intel ich7 Not really used to using command prompt or linux. I'm assuming I'm missing some usb drivers. Any help would be greatly appreciated.

2 1

Asrock N61P-S: Testing reading
by Felix Janda 22 May '12

22 May '12

Hello, reading out the flash chip works. However I don't get the same result each time. More precisely I get equal dumps when reading the chip several times, but I get something different after reboot. The differences appear however only in the region 0x0006e000-0x00070000. The image from the vendor is also identical to the dumps but in this region, where it contains only 0xff. I hope that makes sense. I've included the output of flashrom, lspci and superiotool. Regards. --------------------------------------------------------------------- flashrom v0.9.5.2-r1515 on Linux 3.4.0-rc7gauss+ (x86_64), built with libpci 3.1.9, GCC 4.5.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 2 usecs, 337M loops per second, delay more than 10% too short (got 34% of expected delay), recalculating... 1030M loops per second, 10 myus = 12 us, 100 myus = 101 us, 1000 myus = 1003 us, 10000 myus = 10009 us, 8 myus = 10 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: "ASRock" DMI string baseboard-product-name: "N61P-S" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x40, bit 6 is 1, bit 5 is 0 Flash bus type is SPI SPI on this chipset is WIP. Please report any success or failure by mailing us the verbose output to flashrom(a)flashrom.org, thanks! Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0xfec80000 SPI control is 0x0002, req=0, gnt=0 Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. The following protocols are supported: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L4005" (512 kB, SPI) at physical address 0xfff80000. Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25LF040A, 512 kB: probe_spi_res2: id1 0x12, id2 0x12 Probing for SST SST25LF080A, 1024 kB: probe_spi_res2: id1 0x12, id2 0x12 Probing for SST SST25VF010, 128 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF040, 512 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x12 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Unknown SFDP-capable chip, 0 kB: No SFDP signature found. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2013 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x12 Found Macronix flash chip "MX25L4005" (512 kB, SPI). No operations were specified. --------------------------------------------------------------------- 00:00.0 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller [10de:03ea] (rev a1) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03ea] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=17 MastHost- DefDir- DUL- Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 ea 03 06 00 b0 00 a1 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 ea 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 40: 49 18 ea 03 08 dc 20 02 20 00 11 11 d0 00 00 00 50: 23 06 7f 00 03 00 00 00 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 00 00 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00 80: 23 99 88 00 fa 00 64 0d 03 00 00 00 7f 00 00 00 90: 70 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8 e0: 00 00 e0 fe 00 00 00 00 06 00 00 00 20 10 00 00 f0: f0 ff ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00:01.0 ISA bridge [0601]: nVidia Corporation MCP61 LPC Bridge [10de:03e0] (rev a2) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03e0] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00: de 10 e0 03 0f 00 a0 00 a2 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 e0 03 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 49 18 e0 03 00 00 00 00 fa 3e ff 00 fa 3e ff 00 50: fa 3e ff 00 00 5a 62 02 00 00 00 05 2f 00 3c 01 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 00 ff ff c1 80 00 00 00 00 45 19 00 00 00 c0 80: 09 20 00 d8 01 21 00 00 00 00 40 01 ff 00 00 00 90: ff 7f 00 00 ff ff 3f 3f 21 65 08 74 b9 0c 00 d0 a0: 01 00 00 81 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 90 02 0f 03 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:01.1 SMBus [0c05]: nVidia Corporation MCP61 SMBus [10de:03eb] (rev a2) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03eb] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at dc00 [size=64] Region 4: I/O ports at 5000 [size=64] Region 5: I/O ports at 6000 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus 00: de 10 eb 03 01 00 b0 00 a2 00 05 0c 00 00 80 00 10: 01 dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 50 00 00 01 60 00 00 00 00 00 00 49 18 eb 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 00 00 40: 49 18 eb 03 01 00 02 c0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 40 00 00 01 44 00 00 01 48 00 00 00 00 00 00 70: 00 00 00 00 00 00 c8 fe 00 00 fe fe 01 20 00 00 80: 00 10 fe fe 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: d4 30 80 01 01 00 00 00 00 00 00 00 00 00 00 00 d0: 40 00 40 01 10 00 00 00 05 00 00 00 00 00 00 00 e0: 88 10 04 00 04 40 00 07 80 62 00 20 41 44 44 11 f0: 02 ff 1e bf 01 00 00 80 10 00 00 00 00 00 00 00 00:01.2 RAM memory [0500]: nVidia Corporation MCP61 Memory Controller [10de:03f5] (rev a2) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03eb] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: de 10 f5 03 00 04 a0 00 a2 00 00 05 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 eb 03 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 49 18 f5 03 00 00 00 00 10 02 80 10 10 00 10 10 50: 10 10 10 10 00 00 00 00 00 00 00 00 10 42 00 00 60: 0b 00 00 00 c0 1c 52 06 21 00 10 0a 00 00 63 00 70: 09 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 40 00 00 00 00 00 a0 18 00 00 90: 00 00 00 00 00 00 00 12 20 81 04 00 00 00 00 00 a0: 00 14 00 06 00 00 00 00 00 00 00 00 01 00 00 00 b0: 00 00 00 00 42 80 30 04 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.0 USB controller [0c03]: nVidia Corporation MCP61 USB 1.1 Controller [10de:03f1] (rev a3) (prog-if 10 [OHCI]) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03f1] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: Memory at dbfff000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: de 10 f1 03 07 00 b0 00 a3 10 03 0c 00 00 80 00 10: 00 f0 ff db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 f1 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 01 40: 49 18 f1 03 01 00 02 fe 00 00 00 00 00 00 00 00 50: 40 00 00 00 1d 47 40 00 10 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:02.1 USB controller [0c03]: nVidia Corporation MCP61 USB 2.0 Controller [10de:03f2] (rev a3) (prog-if 20 [EHCI]) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03f2] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 22 Region 0: Memory at dbffec00 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: de 10 f2 03 06 00 b0 00 a3 20 03 0c 00 00 80 00 10: 00 ec ff db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 f2 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 02 03 01 40: 49 18 f2 03 0a 80 98 20 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 01 00 00 60 18 85 c3 13 0f 01 00 00 00 00 70: 00 00 08 00 00 10 20 80 89 3d b6 22 77 25 54 00 80: 01 00 02 fe 00 00 00 00 00 00 00 00 15 16 00 00 90: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 00 00 00 08 40 00 00 00 00 00 00 00 00 b0: 00 11 22 33 44 00 00 00 ff 01 00 00 00 00 00 00 c0: 10 10 2d 0d 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 00:04.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI bridge [10de:03f3] (rev a1) (prog-if 01 [Subtractive decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn- Capabilities: [b8] Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03f3] Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 00: de 10 f3 03 04 00 b0 00 a1 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 22 20: f0 ff 00 00 f0 ff 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 b8 00 00 00 00 00 00 00 00 00 02 02 40: 00 00 73 07 01 00 02 00 07 00 00 00 00 00 48 00 50: 00 00 00 00 00 00 00 00 ff 1f ff 1f 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 03 00 00 80 00 00 00 00 00 00 00 08 00 00 a8 90: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00 a0: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 ff ff 00 00 0d 8c 00 00 49 18 f3 03 c0: 49 18 f3 03 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:05.0 Audio device [0403]: nVidia Corporation MCP61 High Definition Audio [10de:03f0] (rev a2) Subsystem: ASRock Incorporation Device [1849:3662] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin B routed to IRQ 22 Region 0: Memory at dbff8000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable- Count=1/1 Maskable+ 64bit+ Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: snd_hda_intel 00: de 10 f0 03 06 00 b0 00 a2 00 03 04 00 00 80 00 10: 00 80 ff db 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 62 36 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 02 02 05 40: 49 18 62 36 01 50 02 c0 00 00 00 00 01 01 0f 00 50: 05 6c 80 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 02 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 47 00 29 00 00 00 00 00 00 00:07.0 Bridge [0680]: nVidia Corporation MCP61 Ethernet [10de:03ef] (rev a2) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03ef] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 43 Region 0: Memory at dbffd000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at d480 [size=8] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/8 Maskable+ 64bit+ Address: 00000000fee0300c Data: 4179 Masking: 000000fe Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: forcedeth 00: de 10 ef 03 07 04 b0 00 a2 00 80 06 00 00 00 00 10: 00 d0 ff db 81 d4 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 49 18 ef 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 01 14 40: 49 18 ef 03 01 50 02 fe 00 01 00 00 08 00 00 20 50: 05 6c 87 01 0c 30 e0 fe 00 00 00 00 79 41 00 00 60: fe 00 00 00 00 00 00 00 ff 00 00 00 08 00 02 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 42 01 00 00 00 00 00 00 00:08.0 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller [10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03f6] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 21 Region 0: I/O ports at d400 [size=8] Region 1: I/O ports at d080 [size=4] Region 2: I/O ports at d000 [size=8] Region 3: I/O ports at cc00 [size=4] Region 4: I/O ports at c880 [size=16] Region 5: Memory at dbffc000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00: de 10 f6 03 07 00 b0 00 a2 85 01 01 00 00 80 00 10: 01 d4 00 00 81 d0 00 00 01 d0 00 00 01 cc 00 00 20: 81 c8 00 00 00 c0 ff db 00 00 00 00 49 18 f6 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 01 40: 49 18 f6 03 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0f 68 08 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 81 80: 00 00 00 00 ee f7 fb ff 00 00 fc 1d fe 9f ff 75 90: 00 00 f7 30 00 00 00 00 06 00 06 10 f6 03 01 01 a0: 08 00 00 00 00 00 00 00 00 00 00 00 33 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8 d0: 08 00 00 44 00 08 08 00 08 00 00 44 00 08 08 00 e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00:08.1 IDE interface [0101]: nVidia Corporation MCP61 SATA Controller [10de:03f6] (rev a2) (prog-if 85 [Master SecO PriO]) Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03f6] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 20 Region 0: I/O ports at c800 [size=8] Region 1: I/O ports at c480 [size=4] Region 2: I/O ports at c400 [size=8] Region 3: I/O ports at c080 [size=4] Region 4: I/O ports at c000 [size=16] Region 5: Memory at dbff7000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] MSI: Enable- Count=1/4 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+ Kernel driver in use: sata_nv 00: de 10 f6 03 07 00 b0 00 a2 85 01 01 00 00 80 00 10: 01 c8 00 00 81 c4 00 00 01 c4 00 00 81 c0 00 00 20: 01 c0 00 00 00 70 ff db 00 00 00 00 49 18 f6 03 30: 00 00 00 00 44 00 00 00 00 00 00 00 0e 02 03 01 40: 49 18 f6 03 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0f 68 08 00 00 00 00 00 00 00 00 20 40 00 00 20 60: 00 00 00 c7 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 81 80: 00 00 00 40 00 40 8e b7 00 00 08 80 fe ff f7 ff 90: 00 00 69 3d 00 00 00 00 06 00 06 10 f6 03 01 01 a0: 08 00 00 0e 00 00 00 00 00 00 00 00 33 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8 d0: 08 00 00 77 00 08 03 00 08 00 00 44 00 08 08 00 e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00 00 00:09.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e8] (rev a2) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: dc000000-dfffffff Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03e8] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4149 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #1, PowerLimit 75.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport 00: de 10 e8 03 07 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 e1 e1 00 00 20: 00 dc f0 df 01 c0 f1 cf 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 1a 00 40: 0d 48 00 00 49 18 e8 03 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 49 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 01 3d 11 00 90: 40 00 01 31 80 25 08 00 c0 01 48 01 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0b.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e9] (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03e9] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4151 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #2, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport 00: de 10 e9 03 04 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 03 03 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00 40: 0d 48 00 00 49 18 e9 03 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 51 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 11 3c 11 01 90: 00 00 11 10 00 05 10 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:0c.0 PCI bridge [0604]: nVidia Corporation MCP61 PCI Express bridge [10de:03e9] (rev a2) (prog-if 00 [Normal decode]) Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: ASRock Incorporation 939NF6G-VSTA Board [1849:03e9] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] MSI: Enable+ Count=1/2 Maskable- 64bit+ Address: 00000000fee0300c Data: 4159 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise- Slot #3, PowerLimit 10.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=WRR32 Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Kernel driver in use: pcieport 00: de 10 e9 03 04 04 10 00 a2 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 04 04 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00 40: 0d 48 00 00 49 18 e9 03 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c 30 e0 fe 00 00 00 00 59 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 10 28 00 00 11 3c 11 02 90: 00 00 11 10 00 05 18 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Revision ID: 1.02 Link Frequency: 1.0GHz Link Error: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- ExtRS- UCnfE- 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 60: 00 00 01 00 e4 00 00 00 20 c8 2e 0f 0c 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 00 01 21 20 00 11 11 22 06 75 80 02 00 00 00 90: 69 01 61 01 00 00 07 00 07 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 3f 01 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 03 00 e0 00 80 ff ef 00 03 00 c0 00 00 ff df 00 90: 03 00 f0 00 00 0b fe 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 03 0a 00 00 00 0b 00 00 00 00 00 00 00 00 00 00 c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 03 00 00 07 00 00 00 00 00 00 00 00 00 00 00 00 f0: 01 40 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 01 00 00 00 01 02 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: e0 3d f8 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00 80: 05 00 00 00 00 00 00 00 13 91 15 5d 20 12 22 00 90: 10 08 01 00 69 80 10 34 39 00 00 80 00 00 00 00 a0: eb 02 00 5d 00 00 00 00 00 00 00 00 00 00 00 00 b0: 72 a4 33 8f 84 00 00 00 f3 f7 00 01 90 2d 03 f6 c0: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 48 62 d4 93 e7 f0 39 93 1e fa 8b 00 f8 d1 91 e8 e0: c4 62 40 9c c3 b1 de 01 05 a8 03 00 f4 89 18 04 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: ff 3b 04 00 40 00 10 0a 00 00 00 00 00 00 00 00 50: f8 01 f8 ef d5 00 00 00 00 00 00 00 80 ff c2 3f 60: fe 00 00 00 01 77 00 00 00 00 00 00 00 00 00 00 70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00 80: 00 00 07 23 13 21 13 21 00 00 00 00 00 00 00 00 90: 43 00 00 00 5a 00 00 00 00 fc 39 01 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 b0 8c 37 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 01 a7 0d 00 00 00 20 04 25 20 20 00 e0: 00 00 00 00 3e 5c 38 00 19 17 00 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 b2 0f 06 00 02:00.0 VGA compatible controller [0300]: nVidia Corporation G96 [GeForce 9400 GT] [10de:0641] (rev a1) (prog-if 00 [VGA controller]) Subsystem: XFX Pine Group Inc. Device [1682:4009] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at df000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at dc000000 (64-bit, non-prefetchable) [size=32M] Region 5: I/O ports at ec00 [size=128] Expansion ROM at def80000 [disabled] [size=512K] Capabilities: [60] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [b4] Vendor Specific Information: Len=14 <?> Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff Status: NegoPending- InProgress- Capabilities: [128 v1] Power Budgeting <?> Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?> Kernel driver in use: nouveau 00: de 10 41 06 07 01 10 00 a1 00 00 03 10 00 00 00 10: 00 00 00 df 0c 00 00 c0 00 00 00 00 04 00 00 dc 20: 00 00 00 00 01 ec 00 00 00 00 00 00 82 16 09 40 30: 00 00 f8 de 60 00 00 00 00 00 00 00 0a 01 00 00 40: 82 16 09 40 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00 60: 01 68 03 00 00 00 00 00 05 78 80 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 10 b4 01 00 20 85 00 00 80: 10 28 00 00 01 4d 00 00 48 00 01 11 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 09 00 14 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 --------------------------------------------------------------------- superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x0400, id=0x6388 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x8863, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0x8863 Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0x8863, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627EHF/EF/EHG/EG (id=0x88, rev=0x63) at 0x2e Register dump: idx 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f val 88 63 ff 00 04 00 00 ff 50 04 00 00 02 41 00 ff def 88 MM ff 00 MM 00 MM RR 50 04 00 RR 00 21 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 00 00 00 00 04 0e 00 ff 00 00 def 01 03 f0 06 02 8e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 01 03 78 07 03 3b def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 02 f8 03 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 82 def 01 00 60 00 64 01 0c 83 LDN 0x06 (Serial flash interface) idx 30 62 63 val 00 ff ff def 00 00 00 LDN 0x07 (GPIO 1, GPIO 6, game port, MIDI port) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 f7 val 00 02 01 03 30 00 ff ff ff ff ff ff ff 00 def 00 02 01 03 30 09 ff 00 00 00 ff 00 00 00 LDN 0x08 (WDTO#, PLED) idx 30 f5 f6 f7 val 00 ff 00 ff def 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5, SUSLED) idx 30 e0 e1 e2 e3 e4 e5 f0 f1 f2 f3 f4 f5 f6 f7 val 06 ff ff ff ff ff ff a8 bf 00 40 ff ff 00 00 def 00 ff 00 00 ff 00 00 ff 00 00 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 e8 f2 f3 f4 f6 f7 val 00 00 01 00 00 21 00 00 0c 00 09 7c 00 00 00 00 def 00 00 01 00 ff 08 00 RR 00 00 RR 7c 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 f1 val 01 02 90 00 e9 12 def 00 00 00 00 c1 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff

2 3

ASUS M2N-MX: flashrom -V
by fletcher 22 May '12

22 May '12

Hi folks, that's the output of flashrom -V on my system Bios version is 0112 Reading and verifying works fine, writing/erasing doesn't. cheers, Felix Blendinger flashrom v0.9.5.2-r1515 on Linux 3.2.0-2-686-pae (i686), built with libpci 3.1.9, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 2 usecs, 855M loops per second, 10 myus = 12 us, 100 myus = 99 us, 1000 myus = 999 us, 10000 myus = 14186 us, 8 myus = 9 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "ASUSTeK Computer INC." DMI string system-product-name: "M2N-MX" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2N-MX" DMI string baseboard-version: "Rev 1.xx" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0x40000000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x58, id2 0xee, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address 0xfff80000. Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Found SST flash chip "SST49LF040B" (512 kB, LPC). No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88 root@fbock:/usr/local/src/flashrom-0.9.5.2# ./flashrom flashrom v0.9.5.2-r1515 on Linux 3.2.0-2-686-pae (i686), built with libpci 3.1.9, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found chipset "NVIDIA MCP61". Enabling flash write... This chipset is not really supported yet. Guesswork... Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address 0xfff80000. No operations were specified. root@fbock:/usr/local/src/flashrom-0.9.5.2# ./flashrom -V flashrom v0.9.5.2-r1515 on Linux 3.2.0-2-686-pae (i686), built with libpci 3.1.9, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 2 usecs, 786M loops per second, 10 myus = 11 us, 100 myus = 91 us, 1000 myus = 918 us, 10000 myus = 16481 us, 8 myus = 9 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "ASUSTeK Computer INC." DMI string system-product-name: "M2N-MX" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "M2N-MX" DMI string baseboard-version: "Rev 1.xx" DMI string chassis-type: "Desktop" Found ITE Super I/O, ID 0x8712 on port 0x2e Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0x40000000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. Super I/O ID 0x8712 is not on the list of flash capable controllers. The following protocols are supported: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x58, id2 0xee, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address 0xfff80000. Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 Found SST flash chip "SST49LF040B" (512 kB, LPC). No operations were specified. Restoring PCI config space for 00:01:0 reg 0x6d Restoring PCI config space for 00:01:0 reg 0x90 Restoring PCI config space for 00:01:0 reg 0x8c Restoring PCI config space for 00:01:0 reg 0x88

1 0

Intel Q67 read failed
by Schollerer Michael 22 May '12

22 May '12

Hi, this is a verbose output of an unsuccessful read: flashrom v0.9.5.2-r1515 on Linux 2.6.35-22-generic (i686), built with libpci 3.1.7, GCC 4.4.5, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1447M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1001 us, 10000 myus = 10007 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "FUJITSU" DMI string system-product-name: "D3076-K1" DMI string system-version: " " DMI string baseboard-manufacturer: "FUJITSU" DMI string baseboard-product-name: "D3076-K1" DMI string baseboard-version: "S26361-D3076-K1 " DMI string chassis-type: "<OUT OF SPEC>" DMI chassis-type is not specific enough. Found chipset "Intel Q67" with PCI ID 8086:1c4e. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0xc05: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00003000 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x07ff0580 FREG1: BIOS region (0x00580000-0x007fffff) is read-write. 0x5C: 0x057f0003 FREG2: WARNING: Management Engine region (0x00003000-0x0057ffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. Please send a verbose log to flashrom(a)flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf90000 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=1 0x94: 0x0006 (PREOP) 0x96: 0x043b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0000019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000000 (FPB) SPI Read Configuration: prefetching disabled, caching enabled, OK. The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L6405" (8192 kB, SPI) at physical address 0xff800000. Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080A, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF010, 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2017 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xcc, id2 0xb7, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xcc, id2 0xb7, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xb9, id2 0xd1, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Macronix flash chip "MX25L6405" (8192 kB, SPI). Reading flash... SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=1 Running OPCODE 0x03 failed at address 0x003000 (payload length was 64). FAILED. Restoring MMIO space at 0xb780f8a0 Restoring PCI config space for 00:1f:0 reg 0xdc It would be great to get it working, because I really need a bios update! Thanks for your support.

1 0

Success with Pm39LV512 and IT8212F
by Kyösti Mälkki 21 May '12

21 May '12

Report of success with my recent patches. Thanks, Kyösti /tmp # ./flashrom -V -p it8212 -r dump.bin flashrom v0.9.5.2-r1539 on Linux 2.6.39.4 (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Command line (5 args): ./flashrom -V -p it8212 -r dump.bin Calibrating delay loop... OS timer resolution is 1 usecs, 1114M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1015 us, 10000 myus = 9950 us, 4 myus = 5 us, OK. Initializing it8212 programmer Found "ITE 8212F PATA RAID" (1283:8212, BDF 02:02.0). Requested BAR is ROM The following protocols are supported: Parallel. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29F002(N)BB, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29F002(N)BT, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29F016D, 2048 kB: Chip size 2048 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29F040B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29F080B, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV002BB, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV002BT, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV004BB, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV004BT, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV008BB, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV008BT, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV040B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMD Am29LV081B, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMIC A29002B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMIC A29002T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for AMIC A29040B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT29C020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT29C040A, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT49F002(N), 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT49F002(N)T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT49F020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Atmel AT49F040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Bright BM29F040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for EMST F49B002UA, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Eon EN29F002(A)(N)B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Eon EN29F002(A)(N)T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Eon EN29LV640B, 8192 kB: Chip size 8192 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_en29lv640b: id1 0xbd00, id2 0x0000 Probing for Fujitsu MBM29F004BC, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Fujitsu MBM29F004TC, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Fujitsu MBM29F400BC, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_m29f400bt: id1 0xbd, id2 0x00 Probing for Fujitsu MBM29F400TC, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_m29f400bt: id1 0xbd, id2 0x00 Probing for Hyundai HY29F002T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Hyundai HY29F002B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Hyundai HY29F040A, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Macronix MX29F002(N)B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Macronix MX29F002(N)T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Macronix MX29F040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Macronix MX29LV040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29C51400B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29C51400T, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for MoselVitelic V29LC51002, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm29F002T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm29F002B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm39LV020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm39LV040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for PMC Pm39LV512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Found PMC flash chip "Pm39LV512" (64 kB, Parallel) on it8212. Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_82802ab: id1 0xbd, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST29EE020A, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST29LE020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39SF020A, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39SF040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39VF020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39VF040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SST SST39VF080, 1024 kB: Chip size 1024 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29F002B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29F002T/NT, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29F040B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29F400BB, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_m29f400bt: id1 0xbd, id2 0x00 Probing for ST M29F400BT, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_m29f400bt: id1 0xbd, id2 0x00 Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29W040B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for TI TMS29F002RB, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for TI TMS29F002RT, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W29C020(C)/W29C022, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W29C040/P, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W39L040, 512 kB: Chip size 512 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W49F002U/N, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Probing for Winbond W49F020, 256 kB: Chip size 256 kB is bigger than supported size 128 kB of chipset/board/programmer for Parallel interface, probe/read/erase/write may fail. probe_jedec_common: id1 0x9d, id2 0x1b Found PMC flash chip "Pm39LV512" (64 kB, Parallel). Reading flash... done. /tmp # /tmp # ./flashrom -p it8212 -E flashrom v0.9.5.2-r1539 on Linux 2.6.39.4 (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found "ITE 8212F PATA RAID" (1283:8212, BDF 02:02.0). Found PMC flash chip "Pm39LV512" (64 kB, Parallel) on it8212. Erasing and writing flash chip... Erase/write done. /tmp # ./flashrom -p it8212 -v dump.bin flashrom v0.9.5.2-r1539 on Linux 2.6.39.4 (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found "ITE 8212F PATA RAID" (1283:8212, BDF 02:02.0). Found PMC flash chip "Pm39LV512" (64 kB, Parallel) on it8212. Reading old flash chip contents... done. Verifying flash... VERIFY FAILED at 0x00000000! Expected=0xbd, Read=0xff, failed byte count from 0x00000000-0x0000ffff: 0xf9da /tmp # ./flashrom -p it8212 -w dump.bin flashrom v0.9.5.2-r1539 on Linux 2.6.39.4 (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found "ITE 8212F PATA RAID" (1283:8212, BDF 02:02.0). Found PMC flash chip "Pm39LV512" (64 kB, Parallel) on it8212. Reading old flash chip contents... done. Erasing and writing flash chip... Erase/write done. Verifying flash... VERIFIED. /tmp # ./flashrom -p it8212 -v dump.bin flashrom v0.9.5.2-r1539 on Linux 2.6.39.4 (i686), built with libpci 3.0.0, GCC 4.4.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. Found "ITE 8212F PATA RAID" (1283:8212, BDF 02:02.0). Found PMC flash chip "Pm39LV512" (64 kB, Parallel) on it8212. Reading old flash chip contents... done. Verifying flash... VERIFIED.

1 0

Add chip Pm39LV512
by Kyösti Mälkki 20 May '12

20 May '12

This flash is like PMC model Pm39LV010 but capacity is 64kB. Model ID was already defined, PREW works for me. Signed-off-by: Kyösti Mälkki <kyosti.malkki(a)gmail.com> Index: flashrom-pmc64k/flashchips.c =================================================================== --- flashrom-pmc64k/flashchips.c (revision 1538) +++ flashrom-pmc64k/flashchips.c (working copy) @@ -5267,6 +5267,36 @@ { .vendor = "PMC", + .name = "Pm39LV512", + .bustype = BUS_PARALLEL, + .manufacture_id = PMC_ID_NOPREFIX, + .model_id = PMC_PM39LV512, + .total_size = 64, + .page_size = 4096, + .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET, + .tested = TEST_OK_PREW, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 16} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = erase_block_jedec, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + .voltage = {2700, 3600}, + }, + + { + .vendor = "PMC", .name = "Pm39LV010", .bustype = BUS_PARALLEL, .manufacture_id = PMC_ID_NOPREFIX,

3 4

[commit] r1539 - trunk
by repository service 20 May '12

20 May '12

Author: stefanct Date: Mon May 21 01:32:33 2012 New Revision: 1539 URL: http://flashrom.org/trac/flashrom/changeset/1539 Log: Add support for PMC Pm39LV512. This flash is like PMC model Pm39LV010 but capacity is 64kB. Model ID was already defined. PREW works for me. Signed-off-by: Kyösti Mälkki <kyosti.malkki(a)gmail.com> Acked-by: Paul Menzel <paulepanter(a)users.sourceforge.net> Modified: trunk/flashchips.c Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Wed May 16 02:15:53 2012 (r1538) +++ trunk/flashchips.c Mon May 21 01:32:33 2012 (r1539) @@ -5803,7 +5803,37 @@ .read = read_memmapped, .voltage = {2700, 3600}, }, - + + { + .vendor = "PMC", + .name = "Pm39LV512", + .bustype = BUS_PARALLEL, + .manufacture_id = PMC_ID_NOPREFIX, + .model_id = PMC_PM39LV512, + .total_size = 64, + .page_size = 4096, + .feature_bits = FEATURE_ADDR_2AA | FEATURE_EITHER_RESET, + .tested = TEST_OK_PREW, + .probe = probe_jedec, + .probe_timing = TIMING_ZERO, /* Datasheet has no timing info specified */ + .block_erasers = + { + { + .eraseblocks = { {4 * 1024, 16} }, + .block_erase = erase_sector_jedec, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = erase_block_jedec, + }, { + .eraseblocks = { {64 * 1024, 1} }, + .block_erase = erase_chip_block_jedec, + } + }, + .write = write_jedec_1, + .read = read_memmapped, + .voltage = {2700, 3600}, + }, + { .vendor = "PMC", .name = "Pm49FL002",

1 0

(no subject)
by claude 19 May '12

19 May '12

MSI P6NGM motherboard claude@claude-MS-7366:~$ sudo flashrom -V flashrom v0.9.5.2-r1517 on Linux 3.2.0-24-generic (x86_64), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1972M loops per second, 10 myus = 10 us, 100 myus = 97 us, 1000 myus = 965 us, 10000 myus = 11415 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "MSI" DMI string system-product-name: "MS-7366" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "MSI" DMI string baseboard-product-name: "MS-7366" DMI string baseboard-version: "1.0" DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP73" with PCI ID 10de:07d7. Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:07d8 at 00:03:1 MCP SPI BAR is at 0xfeb80000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. The following protocols are supported: LPC. Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xd7, id2 0x99, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xd7, id2 0x99, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xd7, id2 0x99, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xd7, id2 0x99, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xd7, id2 0x99, id1 parity violation, id1 is normal flash content, id2 is normal flash content No EEPROM/flash device found. Note: flashrom can never write if the flash chip isn't found automatically. Restoring PCI config space for 00:03:0 reg 0x6d Restoring PCI config space for 00:03:0 reg 0x90 Restoring PCI config space for 00:03:0 reg 0x8c Restoring PCI config space for 00:03:0 reg 0x88 claude@claude-MS-7366:~$

1 0

Re: [flashrom] PONY_SPI, patch to support a new programmer (AJAWe)
by Stefan Tauner 18 May '12

18 May '12

On Fri, 11 May 2012 14:50:17 +0200 Virgil-Adrian Teaca <darkstarlinux(a)gmail.com> wrote: > There is a new patch for pony_spi, to add support for a new serial > programmer, produced by AJAWe. i asked them for a sample to test or someone that might be able to test it on their hardware. they replied quickly, but are not interested at all. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

← Newer
1
2
3
4
5
6
7
8
9
...
13
Older →

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom May 2012