flashrom January 2012

flashrom@flashrom.org

45 participants
138 discussions

ASUS P5KPL-CM is supported
by nap 11 Jan '12

11 Jan '12

The ASUS P5KPL-CM motherboard is correctly handled by flashrom out of the box. Reading, erasing, writing are OK. The flash chip is a socketed PDIP8 easily hot swappable. Tested with 1M and 2M flash chips. nap # flashrom -V flashrom v0.9.4-r1395 on Linux 3.2.0-gentoo-x86_64-l1 (x86_64), built with libpci 3.1.7, GCC 4.5.3, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 3022M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1000 us, 10000 myus = 10002 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer INC." DMI string baseboard-product-name: "P5KPL-CM" DMI string baseboard-version: "x.xx" DMI string chassis-type: "Desktop" Found chipset "Intel ICH7/ICH7R" with PCI ID 8086:27b8. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x0 Root Complex Register Block address = 0xfed1c000 GCS = 0x10464: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3020 0x00: 0x0004 (SPIS) 0x02: 0x4140 (SPIC) 0x04: 0x00000000 (SPIA) 0x08: 0x000020c2 (SPID0) 0x0c: 0x00000000 (SPID0+4) 0x10: 0x00000000 (SPID1) 0x14: 0x00000000 (SPID1+4) 0x18: 0x00000000 (SPID2) 0x1c: 0x00000000 (SPID2+4) 0x20: 0x00000000 (SPID3) 0x24: 0x00000000 (SPID3+4) 0x28: 0x00000000 (SPID4) 0x2c: 0x00000000 (SPID4+4) 0x30: 0x00000000 (SPID5) 0x34: 0x00000000 (SPID5+4) 0x38: 0x00000000 (SPID6) 0x3c: 0x00000000 (SPID6+4) 0x40: 0x00000000 (SPID7) 0x44: 0x00000000 (SPID7+4) 0x50: 0x00000000 (BBAR) 0x54: 0x0004 (PREOP) 0x56: 0x543b (OPTYPE) 0x58: 0x05d80302 (OPMENU) 0x5c: 0x0006019f (OPMENU+4) 0x60: 0x00000000 (PBR0) 0x64: 0x00000000 (PBR1) 0x68: 0x00000000 (PBR2) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done preop0=0x06, preop1=0x50 op[0]=0x02, 3, 0 op[1]=0x03, 2, 0 op[2]=0xd8, 3, 0 op[3]=0x05, 0, 0 op[4]=0x90, 2, 0 op[5]=0x01, 1, 0 op[6]=0x9f, 0, 0 op[7]=0xc7, 1, 0 SPI Read Configuration: prefetching disabled, caching enabled, OK. This chipset supports the following protocols: SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC A25LQ032, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DF641, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for EMST F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1005, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L2005, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L4005, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L8005, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found Macronix flash chip "MX25L1605" (2048 kB, SPI) at physical address 0xffe00000. Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3205, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L6405, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix MX25L12805, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Numonyx M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV010, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC Pm25LV512, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Sanyo LF25FW203A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL032A, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Spansion S25FL064A, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF010.REMS, 128 kB: probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25VF040.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST SST25LF040A.RES, 512 kB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0x14, id2 0x14 Probing for SST SST25VF040B.REMS, 512 kB: probe_spi_rems: id1 0xc2, id2 0x14 Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P05.RES, 64 kB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P10.RES, 128 kB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2015 Probing for Generic unknown SPI chip (REMS), 0 kB: probe_spi_rems: id1 0xc2, id2 0x14 No operations were specified. Restoring MMIO space at 0x7f056f667070 Restoring MMIO space at 0x7f056f66707c Restoring MMIO space at 0x7f056f667078 Restoring MMIO space at 0x7f056f667076 Restoring MMIO space at 0x7f056f667074 Restoring PCI config space for 00:1f:0 reg 0xdc # lspci -nnvvxxx 00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller [8086:29c0] (rev 10) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:82b0] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0b <?> Kernel driver in use: agpgart-intel 00: 86 80 c0 29 06 00 90 20 10 00 00 06 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 b0 82 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 90 d1 fe 01 00 00 00 00 40 d1 fe 00 00 00 00 50: 00 00 30 01 09 00 00 00 00 00 00 00 00 00 00 00 60: 05 00 00 f0 00 00 00 00 01 80 d1 fe 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 10 11 01 00 00 33 33 00 ff 03 00 00 00 1a 38 00 a0: 20 00 00 08 00 00 80 7f 00 00 70 7f 00 00 70 7f b0: 00 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 49 00 00 00 00 00 00 e6 e0: 09 00 0b b1 62 00 a5 2b 63 1c 16 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 90 0f 10 00 00 00 00 00 00:02.0 VGA compatible controller [0300]: Intel Corporation 82G33/G31 Express Integrated Graphics Controller [8086:29c2] (rev 10) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:82b0] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe980000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at dc00 [size=8] Region 2: Memory at e0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Expansion ROM at <unassigned> [disabled] Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [d0] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: i915 00: 86 80 c2 29 07 00 90 00 10 00 00 03 00 00 00 00 10: 00 00 98 fe 01 dc 00 00 08 00 00 e0 00 00 80 fe 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 b0 82 30: 00 00 00 00 90 00 00 00 00 00 00 00 0a 01 00 00 40: 09 00 0b b1 62 00 a5 2b 63 1c 16 00 00 00 00 00 50: 00 00 30 01 09 00 00 00 00 00 00 00 00 00 80 7f 60: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 05 d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 11 11 00 00 00 00 06 03 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 01 00 22 00 00 00 00 00 00 00 00 00 00 01 02 00 e0: 00 00 00 00 00 00 00 00 00 80 00 00 00 00 00 00 f0: 12 00 03 00 00 00 00 00 90 0f 10 00 e4 e0 69 7f 00:1b.0 Audio device [0403]: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller [8086:27d8] (rev 01) Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard [1043:82ea] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at fe978000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [70] Express (v1) Root Complex Integrated Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed unknown, Width x0, ASPM unknown, Latency L0 <64ns, L1 <1us ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed unknown, Width x0, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed- WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [130 v1] Root Complex Link Desc: PortNumber=0f ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c000 Kernel driver in use: snd_hda_intel 00: 86 80 d8 27 06 00 10 00 01 00 03 04 08 00 00 00 10: 04 80 97 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ea 82 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 01 00 00 40: 03 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 60 42 c8 00 00 00 00 00 00 00 00 00 00 00 00 60: 05 70 80 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 10 00 91 00 00 00 00 00 00 08 10 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1c.0 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 I/O behind bridge: 00001000-00001fff Memory behind bridge: 7f900000-7fafffff Prefetchable memory behind bridge: 000000007fb00000-000000007fcfffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <1us, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #4, PowerLimit 25.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device [1043:8179] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed+ WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [180 v1] Root Complex Link Desc: PortNumber=01 ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c001 00: 86 80 d0 27 07 01 10 00 01 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 10 10 00 00 20: 90 7f a0 7f b1 7f c1 7f 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 02 00 40: 10 80 41 01 c0 0f 00 00 00 00 10 00 11 4c 11 01 50: 00 00 01 10 e0 0c 20 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 43 10 79 81 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 11 00 00 00 00 00 e0: 00 00 c7 00 06 07 08 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1c.1 PCI bridge [0604]: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 [8086:27d2] (rev 01) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fea00000-feafffff Prefetchable memory behind bridge: 000000007f700000-000000007f8fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited ExtTag- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 128 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <256ns, L1 <4us ClockPM- Surprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Slot #0, PowerLimit 0.000W; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit- Address: 00000000 Data: 0000 Capabilities: [90] Subsystem: ASUSTeK Computer Inc. Device [1043:8179] Capabilities: [a0] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [100 v1] Virtual Channel Caps: LPEVC=0 RefClk=100ns PATEntryBits=1 Arb: Fixed+ WRR32- WRR64- WRR128- Ctrl: ArbSelect=Fixed Status: InProgress- VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=01 Status: NegoPending- InProgress- VC1: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans- Arb: Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256- Ctrl: Enable- ID=0 ArbSelect=Fixed TC/VC=00 Status: NegoPending- InProgress- Capabilities: [180 v1] Root Complex Link Desc: PortNumber=02 ComponentID=00 EltType=Config Link0: Desc: TargetPort=00 TargetComponent=00 AssocRCRB- LinkType=MemMapped LinkValid+ Addr: 00000000fed1c001 00: 86 80 d2 27 07 01 10 00 01 00 04 06 08 00 81 00 10: 00 00 00 00 00 00 00 00 00 01 01 00 e0 e0 00 00 20: a0 fe a0 fe 71 7f 81 7f 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 02 00 40: 10 80 41 01 c0 0f 00 00 00 00 10 00 11 2c 11 02 50: 40 00 11 30 60 00 00 00 00 00 48 01 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 0d a0 00 00 43 10 79 81 00 00 00 00 00 00 00 00 a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 11 00 00 00 00 00 e0: 00 00 c7 00 06 07 08 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1d.0 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 4: I/O ports at d400 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 c8 27 05 00 80 02 01 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d4 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1d.1 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at d480 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 c9 27 05 00 80 02 01 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 d4 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1d.2 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at d800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 ca 27 05 00 80 02 01 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 d8 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 03 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1d.3 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 [8086:27cb] (rev 01) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 16 Region 4: I/O ports at d880 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 cb 27 05 00 80 02 01 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 d8 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 04 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 2f 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1d.7 USB Controller [0c03]: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 23 Region 0: Memory at fe977c00 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [58] Debug port: BAR=1 offset=00a0 Kernel driver in use: ehci_hcd 00: 86 80 cc 27 06 00 90 02 01 20 03 0c 00 00 00 00 10: 00 7c 97 fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 50 00 00 00 00 00 00 00 05 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 58 c2 c9 00 00 00 00 0a 00 a0 20 00 00 00 00 60: 20 20 ff 01 00 00 00 00 01 00 00 00 00 00 08 c0 70: 00 00 cf 3f 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 aa ff 00 ff 00 ff 00 20 00 00 88 e0: 00 00 00 00 db b6 6d 00 00 00 00 00 00 00 00 00 f0: 00 80 00 09 88 85 40 00 86 0f 01 00 0a 17 02 20 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev e1) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=03, subordinate=03, sec-latency=32 Memory behind bridge: feb00000-febfffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [50] Subsystem: ASUSTeK Computer Inc. Device [1043:8179] 00: 86 80 4e 24 07 01 10 00 e1 01 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 03 03 20 f0 00 80 22 20: b0 fe b0 fe f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 02 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 12 00 00 50: 0d 00 00 00 43 10 79 81 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge [8086:27b8] (rev 01) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [e0] Vendor Specific Information: Len=0c <?> 00: 86 80 b8 27 07 00 10 02 01 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 40: 01 08 00 00 80 00 00 00 81 04 00 00 10 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 8a 8b 8f 83 d0 00 00 00 80 80 80 85 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 0f 14 95 02 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 28 06 00 00 39 00 00 00 13 00 00 00 00 03 00 00 b0: 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 33 22 11 00 67 45 00 00 c0 c0 00 00 00 00 00 00 e0: 09 00 0c 10 a8 00 24 00 00 00 00 00 00 00 00 00 f0: 01 c0 d1 fe 00 00 00 00 86 0f 01 00 00 00 00 00 00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+ Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at c480 [size=8] Region 1: I/O ports at c400 [size=4] Region 2: I/O ports at 08f0 [size=8] Region 3: I/O ports at 08f8 [size=4] Region 4: I/O ports at bc00 [size=16] Kernel driver in use: ata_piix 00: 86 80 df 27 05 00 88 02 01 8f 01 01 00 00 00 00 10: 81 c4 00 00 01 c4 00 00 f1 08 00 00 f9 08 00 00 20: 01 bc 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 0f 01 00 00 40: 00 c0 00 40 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1f.2 IDE interface [0101]: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 0: I/O ports at d080 [size=8] Region 1: I/O ports at d000 [size=4] Region 2: I/O ports at cc00 [size=8] Region 3: I/O ports at c880 [size=4] Region 4: I/O ports at c800 [size=16] Capabilities: [70] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ata_piix 00: 86 80 c0 27 05 00 b0 02 01 8f 01 01 00 00 00 00 10: 81 d0 00 00 01 d0 00 00 01 cc 00 00 81 c8 00 00 20: 01 c8 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 70 00 00 00 00 00 00 00 03 02 00 00 40: 07 a3 03 a3 00 00 00 00 05 00 01 01 00 00 00 00 50: 00 00 00 00 f0 50 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 01 00 02 40 00 00 00 00 00 00 00 00 00 00 00 00 80: 05 70 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 3f 00 80 01 00 40 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 05 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 00:1f.3 SMBus [0c05]: Intel Corporation 82801G (ICH7 Family) SMBus Controller [8086:27da] (rev 01) Subsystem: ASUSTeK Computer Inc. P5KPL-VM Motherboard [1043:8179] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at 0400 [size=32] Kernel driver in use: i801_smbus 00: 86 80 da 27 01 00 80 02 01 00 05 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 79 81 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 86 0f 01 00 00 00 00 00 01:00.0 Ethernet controller [0200]: Attansic Technology Corp. Atheros AR8121/AR8113/AR8114 PCI-E Ethernet Controller [1969:1026] (rev b0) Subsystem: ASUSTeK Computer Inc. P5KPL-CM Motherboard [1043:8304] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 17 Region 0: Memory at feac0000 (64-bit, non-prefetchable) [size=256K] Region 2: I/O ports at ec00 [size=128] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+ Address: 0000000000000000 Data: 0000 Capabilities: [58] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 4096 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited ExtTag- AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited ClockPM- Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt+ UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn- Capabilities: [180 v1] Device Serial Number ff-c4-f8-88-00-1f-c6-ff Kernel driver in use: ATL1E 00: 69 19 26 10 07 00 10 00 b0 00 00 02 08 00 00 00 10: 04 00 ac fe 00 00 00 00 01 ec 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 04 83 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00 40: 01 48 02 c0 00 00 00 00 05 58 80 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 10 00 01 00 85 7f 00 00 60: 00 20 1a 00 11 f4 03 00 40 00 11 10 03 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 69 19 26 10 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03:00.0 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 19 Region 0: Memory at febfd000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: 33 10 35 00 16 00 10 02 41 10 03 0c 08 40 80 00 10: 00 d0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 33 10 35 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 01 2a 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 05 33 30 c4 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03:00.1 USB Controller [0c03]: NEC Corporation USB [1033:0035] (rev 41) (prog-if 10 [OHCI]) Subsystem: NEC Corporation Hama USB 2.0 CardBus [1033:0035] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (250ns min, 10500ns max), Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 16 Region 0: Memory at febfe000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: 33 10 35 00 16 00 10 02 41 10 03 0c 08 40 00 00 10: 00 e0 bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 33 10 35 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 01 2a 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03:00.2 USB Controller [0c03]: NEC Corporation USB 2.0 [1033:00e0] (rev 02) (prog-if 20 [EHCI]) Subsystem: HaSoTec GmbH Device [0e55:2928] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (4000ns min, 8500ns max), Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 17 Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=256] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: 33 10 e0 00 16 00 10 02 02 20 03 0c 08 40 00 00 10: 00 fc bf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 55 0e 28 29 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 03 10 22 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 3f 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 05 33 30 c4 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 # superiotool -deV superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x4400, id=0x23a0 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0xffff, id=0xffff Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x25e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0xa023, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x164e... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O at 0x164e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for Nuvoton Super I/O at 0x2e... Failed. Returned data: chip_id=0xa023 Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0xa023, rev=0x00 Probing for Nuvoton Super I/O at 0x4e... Failed. Returned data: chip_id=0xffff Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e... Failed. Returned data: sid=0xff, id=0xffff, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627DHG (id=0xa0, rev=0x23) at 0x2e Register dump: idx 02 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f val ff a0 23 ff 00 44 00 00 ff 50 00 00 00 9a 21 00 ff def 00 a0 NA ff 00 MM 00 MM RR 50 00 00 RR e2 21 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 01 03 f0 06 02 0e 00 ff 00 00 def 01 03 f0 06 02 8e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 01 03 78 07 03 3a def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 02 f8 03 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 83 def 01 00 60 00 64 01 0c 83 LDN 0x06 (Serial peripheral interface) idx 30 62 63 val 00 ff ff def 00 00 00 LDN 0x07 (GPIO 6) idx 30 f4 f5 f6 f7 val 06 ff ff ff ff def 00 ff 00 00 00 LDN 0x08 (WDTO#, PLED) idx 30 f5 f6 f7 val 00 ff 00 ff def 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5) idx 30 e0 e1 e2 e3 e4 e5 e6 e7 e8 e9 f0 f1 f2 f3 f4 f5 f6 f7 fe val 07 ff ff ff fb 08 00 00 0c 1f ff f3 08 00 09 06 fe 00 00 00 def 00 ff 00 00 ff 00 00 00 00 00 00 ff 00 00 00 ff 00 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 e8 e9 f2 f3 f4 f6 f7 fe val 00 00 00 00 30 04 00 02 1c 10 09 00 7d 00 00 00 00 00 def 00 00 01 00 ff 08 00 RR 1c 00 RR RR 7c 00 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 f1 f2 val 01 02 90 00 81 ff 83 def 00 00 00 00 81 00 00 LDN 0x0c (PECI, SST) idx e0 e1 e2 e3 e4 e5 e8 f1 fe ff val 10 64 48 48 48 00 01 48 ee 80 def 00 48 48 48 48 00 00 48 00 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Server Engines Super I/O at 0x2e... Failed. Returned data: id=0xffff, rev=0xff

2 3

Fwd: flashrom -V
by Idwer Vollering 11 Jan '12

11 Jan '12

---------- Forwarded message ---------- From: Vince S <vince06fr(a)gmail.com> Date: 2012/1/11 Subject: Re: [flashrom] flashrom -V To: Idwer Vollering <vidwer(a)gmail.com> It s to late i already shutdown the oc so i can t restart... Le 11 janv. 2012 16:58, "Idwer Vollering" <vidwer(a)gmail.com> a écrit : > 2012/1/11 Idwer Vollering <vidwer(a)gmail.com>: > > 2012/1/11 Vince S <vince06fr(a)gmail.com>: > >> Hello > >> The output of flashrom -V : > >> > >> > >> flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci > >> 3.1.7, GCC 4.6.1, little endian > >> flashrom is free software, get the source code at http://www.flashrom.org > >> > >> Calibrating delay loop... OS timer resolution is 1 usecs, 736M loops per > >> second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1000 us, 10000 myus > >> = 10004 us, 4 myus = 5 us, OK. > >> Initializing internal programmer > >> No coreboot table found. > >> DMI string system-manufacturer: "Acer" > >> DMI string system-product-name: "Aspire T180" > >> DMI string system-version: "R01-A2" > >> DMI string baseboard-manufacturer: "Acer" > >> DMI string baseboard-product-name: "EM61SM/EM61PM " > >> DMI string baseboard-version: " " > >> DMI string chassis-type: "Desktop" > >> Found ITE Super I/O, ID 0x8726 on port 0x2e > >> Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. > >> This chipset is marked as untested. If you are using an up-to-date version > >> of flashrom please email a report to flashrom(a)flashrom.org including a > >> verbose (-V) log. Thank you! > >> Enabling flash write... This chipset is not really supported yet. > >> Guesswork... > >> ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 > >> Flash bus type is LPC > >> Found SMBus device 10de:03eb at 00:01:1 > >> MCP SPI BAR is at 0x00000000 > >> MCP SPI is not used. > >> Please send the output of "flashrom -V" to flashrom(a)flashrom.org with > >> your board name: flashrom -V as the subject to help us finish support for > >> your > >> chipset. Thanks. > >> OK. > >> This chipset supports the following protocols: LPC. > >> Super I/O ID 0x8726 is not on the list of flash capable controllers. > >> Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address > >> 0xfff80000. > >> Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing > >> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 > >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > >> content > >> > >> Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > >> normal flash content, id2 is normal flash content > >> Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > >> normal flash content, id2 is normal flash content > >> Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 > >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > >> content > >> Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 > >> 0x50, id1 is normal flash content > >> === > >> This flash part has status UNTESTED for operations: WRITE > >> The test status of this chip may have been updated in the latest development > >> version of flashrom. If you are running the latest development version, > >> please email a report to flashrom(a)flashrom.org if any of the above > >> operations > >> work correctly for you with this flash part. Please include the flashrom > >> output with the additional -V option for all operations you tested (-V, -Vr, > >> -Vw, -VE), and mention which mainboard or programmer you tested. > >> Please mention your board in the subject line. Thanks for your help! > >> > >> No operations were specified. > >> Restoring PCI config space for 00:01:0 reg 0x6d > >> Restoring PCI config space for 00:01:0 reg 0x90 > >> Restoring PCI config space for 00:01:0 reg 0x8c > >> Restoring PCI config space for 00:01:0 reg 0x88 > >> > >> > >> ======================================== > >> > >> Here the output of flashrom -VE : > >> > >> flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci > >> 3.1.7, GCC 4.6.1, little endian > >> flashrom is free software, get the source code at http://www.flashrom.org > >> > >> Calibrating delay loop... OS timer resolution is 1 usecs, 729M loops per > >> second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 990 us, 10000 myus = > >> 9955 us, 4 myus = 5 us, OK. > >> Initializing internal programmer > >> No coreboot table found. > >> DMI string system-manufacturer: "Acer" > >> DMI string system-product-name: "Aspire T180" > >> DMI string system-version: "R01-A2" > >> DMI string baseboard-manufacturer: "Acer" > >> DMI string baseboard-product-name: "EM61SM/EM61PM " > >> DMI string baseboard-version: " " > >> DMI string chassis-type: "Desktop" > >> Found ITE Super I/O, ID 0x8726 on port 0x2e > >> Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. > >> This chipset is marked as untested. If you are using an up-to-date version > >> of flashrom please email a report to flashrom(a)flashrom.org including a > >> verbose (-V) log. Thank you! > >> Enabling flash write... This chipset is not really supported yet. > >> Guesswork... > >> ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 > >> Flash bus type is LPC > >> Found SMBus device 10de:03eb at 00:01:1 > >> MCP SPI BAR is at 0x00000000 > >> MCP SPI is not used. > >> Please send the output of "flashrom -V" to flashrom(a)flashrom.org with > >> your board name: flashrom -V as the subject to help us finish support for > >> your > >> chipset. Thanks. > >> OK. > >> This chipset supports the following protocols: LPC. > >> Super I/O ID 0x8726 is not on the list of flash capable controllers. > >> Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > >> id1 is normal flash content > >> Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address > >> 0xfff80000. > >> Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing > >> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 > >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > >> content > >> > >> Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > >> normal flash content, id2 is normal flash content > >> Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > >> normal flash content, id2 is normal flash content > >> Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > >> parity violation, id1 is normal flash content, id2 is normal flash content > >> Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > >> Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 > >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > >> content > >> Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 > >> 0x50, id1 is normal flash content > >> === > >> This flash part has status UNTESTED for operations: WRITE > >> The test status of this chip may have been updated in the latest development > >> version of flashrom. If you are running the latest development version, > >> please email a report to flashrom(a)flashrom.org if any of the above > >> operations > >> work correctly for you with this flash part. Please include the flashrom > >> output with the additional -V option for all operations you tested (-V, -Vr, > >> -Vw, -VE), and mention which mainboard or programmer you tested. > >> Please mention your board in the subject line. Thanks for your help! > >> Erasing and writing flash chip... Trying erase function 0... > >> 0x000000-0x000fff:E, 0x001000-0x001fff:E, 0x002000-0x002fff:E, > >> 0x003000-0x003fff:E, 0x004000-0x004fff:E, 0x005000-0x005fff:E, > >> 0x006000-0x006fff:E, 0x007000-0x007fff:E, 0x008000-0x008fff:E, > >> 0x009000-0x009fff:E, 0x00a000-0x00afff:E, 0x00b000-0x00bfff:E, > >> 0x00c000-0x00cfff:E, 0x00d000-0x00dfff:E, 0x00e000-0x00efff:E, > >> 0x00f000-0x00ffff:E, 0x010000-0x010fff:E, 0x011000-0x011fff:E, > >> 0x012000-0x012fff:E, 0x013000-0x013fff:E, 0x014000-0x014fff:E, > >> 0x015000-0x015fff:E, 0x016000-0x016fff:E, 0x017000-0x017fff:E, > >> 0x018000-0x018fff:E, 0x019000-0x019fff:E, 0x01a000-0x01afff:E, > >> 0x01b000-0x01bfff:E, 0x01c000-0x01cfff:E, 0x01d000-0x01dfff:E, > >> 0x01e000-0x01efff:E, 0x01f000-0x01ffff:E, 0x020000-0x020fff:E, > >> 0x021000-0x021fff:E, 0x022000-0x022fff:E, 0x023000-0x023fff:E, > >> 0x024000-0x024fff:E, 0x025000-0x025fff:E, 0x026000-0x026fff:E, > >> 0x027000-0x027fff:E, 0x028000-0x028fff:E, 0x029000-0x029fff:E, > >> 0x02a000-0x02afff:E, 0x02b000-0x02bfff:E, 0x02c000-0x02cfff:E, > >> 0x02d000-0x02dfff:E, 0x02e000-0x02efff:E, 0x02f000-0x02ffff:E, > >> 0x030000-0x030fff:E, 0x031000-0x031fff:E, 0x032000-0x032fff:E, > >> 0x033000-0x033fff:E, 0x034000-0x034fff:E, 0x035000-0x035fff:E, > >> 0x036000-0x036fff:E, 0x037000-0x037fff:E, 0x038000-0x038fff:E, > >> 0x039000-0x039fff:E, 0x03a000-0x03afff:E, 0x03b000-0x03bfff:E, > >> 0x03c000-0x03cfff:E, 0x03d000-0x03dfff:E, 0x03e000-0x03efff:E, > >> 0x03f000-0x03ffff:E, 0x040000-0x040fff:E, 0x041000-0x041fff:E, > >> 0x042000-0x042fff:E, 0x043000-0x043fff:E, 0x044000-0x044fff:E, > >> 0x045000-0x045fff:E, 0x046000-0x046fff:E, 0x047000-0x047fff:E, > >> 0x048000-0x048fff:E, 0x049000-0x049fff:E, 0x04a000-0x04afff:E, > >> 0x04b000-0x04bfff:E, 0x04c000-0x04cfff:E, 0x04d000-0x04dfff:E, > >> 0x04e000-0x04efff:E, 0x04f000-0x04ffff:E, 0x050000-0x050fff:E, > >> 0x051000-0x051fff:E, 0x052000-0x052fff:E, 0x053000-0x053fff:E, > >> 0x054000-0x054fff:E, 0x055000-0x055fff:E, 0x056000-0x056fff:E, > >> 0x057000-0x057fff:E, 0x058000-0x058fff:E, 0x059000-0x059fff:E, > >> 0x05a000-0x05afff:E, 0x05b000-0x05bfff:E, 0x05c000-0x05cfff:E, > >> 0x05d000-0x05dfff:E, 0x05e000-0x05efff:E, 0x05f000-0x05ffff:E, > >> 0x060000-0x060fff:E, 0x061000-0x061fff:E, 0x062000-0x062fff:E, > >> 0x063000-0x063fff:E, 0x064000-0x064fff:E, 0x065000-0x065fff:E, > >> 0x066000-0x066fff:E, 0x067000-0x067fff:E, 0x068000-0x068fff:E, > >> 0x069000-0x069fff:E, 0x06a000-0x06afff:E, 0x06b000-0x06bfff:E, > >> 0x06c000-0x06cfff:E, 0x06d000-0x06dfff:E, 0x06e000-0x06efff:E, > >> 0x06f000-0x06ffff:E, 0x070000-0x070fff:E, 0x071000-0x071fff:E, > >> 0x072000-0x072fff:E, 0x073000-0x073fff:E, 0x074000-0x074fff:E, > >> 0x075000-0x075fff:E, 0x076000-0x076fff:E, 0x077000-0x077fff:E, > >> 0x078000-0x078fff:E, 0x079000-0x079fff:E, 0x07a000-0x07afff:E, > >> 0x07b000-0x07bfff:E, 0x07c000-0x07cfff:E, 0x07d000-0x07dfff:E, > >> 0x07e000-0x07efff:E, 0x07f000-0x07ffff:E > >> Erase/write done. > > > > The chip is now erased, it doesn't contain BIOS/(U)EFI software anymore. > > > >> > >> Restoring PCI config space for 00:01:0 reg 0x6d > >> Restoring PCI config space for 00:01:0 reg 0x90 > >> Restoring PCI config space for 00:01:0 reg 0x8c > >> Restoring PCI config space for 00:01:0 reg 0x88 > >> > >> > >> =================================================== > >> > >> If you want the output of another command, please ask me > >> I finally flash my bios with a windows live disk so i don't want to take > >> anyu risk but i want help > > > > Please do not reboot as your machine may have to be sent in for repair. > > Unless you have made a backup readout file, we will supply a link for > > the right BIOS rom. > > Here is the link: > ftp://ftp.work.acer-euro.com/desktop/aspire_t180/bios/R01B4.zip and > DOS/61AO427.BIN is the file that - I think - suits your board. > > > > >> > >> > >> > >> > >> _______________________________________________ > >> flashrom mailing list > >> flashrom(a)flashrom.org > >> http://www.flashrom.org/mailman/listinfo/flashrom

1 0

Abit NF-M2 nView upgrade problem
by Grzesiek Pycia 11 Jan '12

11 Jan '12

Hi I'm trying to upgrade bios on Abit NF-M2 nView mainboard which is marked as supported but it is impossible, because it fails on erasing the chip, so I'm sending log as advised by flashrom. If there are some other information needed or testing please let me know I'll be happy to help out. Regards Grzegorz

3 5

Re: [flashrom] flashrom -V
by Idwer Vollering 11 Jan '12

11 Jan '12

2012/1/11 Idwer Vollering <vidwer(a)gmail.com>: > 2012/1/11 Vince S <vince06fr(a)gmail.com>: >> Hello >> The output of flashrom -V : >> >> >> flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci >> 3.1.7, GCC 4.6.1, little endian >> flashrom is free software, get the source code at http://www.flashrom.org >> >> Calibrating delay loop... OS timer resolution is 1 usecs, 736M loops per >> second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1000 us, 10000 myus >> = 10004 us, 4 myus = 5 us, OK. >> Initializing internal programmer >> No coreboot table found. >> DMI string system-manufacturer: "Acer" >> DMI string system-product-name: "Aspire T180" >> DMI string system-version: "R01-A2" >> DMI string baseboard-manufacturer: "Acer" >> DMI string baseboard-product-name: "EM61SM/EM61PM " >> DMI string baseboard-version: " " >> DMI string chassis-type: "Desktop" >> Found ITE Super I/O, ID 0x8726 on port 0x2e >> Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. >> This chipset is marked as untested. If you are using an up-to-date version >> of flashrom please email a report to flashrom(a)flashrom.org including a >> verbose (-V) log. Thank you! >> Enabling flash write... This chipset is not really supported yet. >> Guesswork... >> ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 >> Flash bus type is LPC >> Found SMBus device 10de:03eb at 00:01:1 >> MCP SPI BAR is at 0x00000000 >> MCP SPI is not used. >> Please send the output of "flashrom -V" to flashrom(a)flashrom.org with >> your board name: flashrom -V as the subject to help us finish support for >> your >> chipset. Thanks. >> OK. >> This chipset supports the following protocols: LPC. >> Super I/O ID 0x8726 is not on the list of flash capable controllers. >> Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address >> 0xfff80000. >> Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing >> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash >> content >> >> Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is >> normal flash content, id2 is normal flash content >> Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is >> normal flash content, id2 is normal flash content >> Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash >> content >> Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 >> 0x50, id1 is normal flash content >> === >> This flash part has status UNTESTED for operations: WRITE >> The test status of this chip may have been updated in the latest development >> version of flashrom. If you are running the latest development version, >> please email a report to flashrom(a)flashrom.org if any of the above >> operations >> work correctly for you with this flash part. Please include the flashrom >> output with the additional -V option for all operations you tested (-V, -Vr, >> -Vw, -VE), and mention which mainboard or programmer you tested. >> Please mention your board in the subject line. Thanks for your help! >> >> No operations were specified. >> Restoring PCI config space for 00:01:0 reg 0x6d >> Restoring PCI config space for 00:01:0 reg 0x90 >> Restoring PCI config space for 00:01:0 reg 0x8c >> Restoring PCI config space for 00:01:0 reg 0x88 >> >> >> ======================================== >> >> Here the output of flashrom -VE : >> >> flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci >> 3.1.7, GCC 4.6.1, little endian >> flashrom is free software, get the source code at http://www.flashrom.org >> >> Calibrating delay loop... OS timer resolution is 1 usecs, 729M loops per >> second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 990 us, 10000 myus = >> 9955 us, 4 myus = 5 us, OK. >> Initializing internal programmer >> No coreboot table found. >> DMI string system-manufacturer: "Acer" >> DMI string system-product-name: "Aspire T180" >> DMI string system-version: "R01-A2" >> DMI string baseboard-manufacturer: "Acer" >> DMI string baseboard-product-name: "EM61SM/EM61PM " >> DMI string baseboard-version: " " >> DMI string chassis-type: "Desktop" >> Found ITE Super I/O, ID 0x8726 on port 0x2e >> Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. >> This chipset is marked as untested. If you are using an up-to-date version >> of flashrom please email a report to flashrom(a)flashrom.org including a >> verbose (-V) log. Thank you! >> Enabling flash write... This chipset is not really supported yet. >> Guesswork... >> ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 >> Flash bus type is LPC >> Found SMBus device 10de:03eb at 00:01:1 >> MCP SPI BAR is at 0x00000000 >> MCP SPI is not used. >> Please send the output of "flashrom -V" to flashrom(a)flashrom.org with >> your board name: flashrom -V as the subject to help us finish support for >> your >> chipset. Thanks. >> OK. >> This chipset supports the following protocols: LPC. >> Super I/O ID 0x8726 is not on the list of flash capable controllers. >> Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, >> id1 is normal flash content >> Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address >> 0xfff80000. >> Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing >> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash >> content >> >> Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is >> normal flash content, id2 is normal flash content >> Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is >> normal flash content, id2 is normal flash content >> Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 >> parity violation, id1 is normal flash content, id2 is normal flash content >> Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 >> Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 >> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash >> content >> Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 >> 0x50, id1 is normal flash content >> === >> This flash part has status UNTESTED for operations: WRITE >> The test status of this chip may have been updated in the latest development >> version of flashrom. If you are running the latest development version, >> please email a report to flashrom(a)flashrom.org if any of the above >> operations >> work correctly for you with this flash part. Please include the flashrom >> output with the additional -V option for all operations you tested (-V, -Vr, >> -Vw, -VE), and mention which mainboard or programmer you tested. >> Please mention your board in the subject line. Thanks for your help! >> Erasing and writing flash chip... Trying erase function 0... >> 0x000000-0x000fff:E, 0x001000-0x001fff:E, 0x002000-0x002fff:E, >> 0x003000-0x003fff:E, 0x004000-0x004fff:E, 0x005000-0x005fff:E, >> 0x006000-0x006fff:E, 0x007000-0x007fff:E, 0x008000-0x008fff:E, >> 0x009000-0x009fff:E, 0x00a000-0x00afff:E, 0x00b000-0x00bfff:E, >> 0x00c000-0x00cfff:E, 0x00d000-0x00dfff:E, 0x00e000-0x00efff:E, >> 0x00f000-0x00ffff:E, 0x010000-0x010fff:E, 0x011000-0x011fff:E, >> 0x012000-0x012fff:E, 0x013000-0x013fff:E, 0x014000-0x014fff:E, >> 0x015000-0x015fff:E, 0x016000-0x016fff:E, 0x017000-0x017fff:E, >> 0x018000-0x018fff:E, 0x019000-0x019fff:E, 0x01a000-0x01afff:E, >> 0x01b000-0x01bfff:E, 0x01c000-0x01cfff:E, 0x01d000-0x01dfff:E, >> 0x01e000-0x01efff:E, 0x01f000-0x01ffff:E, 0x020000-0x020fff:E, >> 0x021000-0x021fff:E, 0x022000-0x022fff:E, 0x023000-0x023fff:E, >> 0x024000-0x024fff:E, 0x025000-0x025fff:E, 0x026000-0x026fff:E, >> 0x027000-0x027fff:E, 0x028000-0x028fff:E, 0x029000-0x029fff:E, >> 0x02a000-0x02afff:E, 0x02b000-0x02bfff:E, 0x02c000-0x02cfff:E, >> 0x02d000-0x02dfff:E, 0x02e000-0x02efff:E, 0x02f000-0x02ffff:E, >> 0x030000-0x030fff:E, 0x031000-0x031fff:E, 0x032000-0x032fff:E, >> 0x033000-0x033fff:E, 0x034000-0x034fff:E, 0x035000-0x035fff:E, >> 0x036000-0x036fff:E, 0x037000-0x037fff:E, 0x038000-0x038fff:E, >> 0x039000-0x039fff:E, 0x03a000-0x03afff:E, 0x03b000-0x03bfff:E, >> 0x03c000-0x03cfff:E, 0x03d000-0x03dfff:E, 0x03e000-0x03efff:E, >> 0x03f000-0x03ffff:E, 0x040000-0x040fff:E, 0x041000-0x041fff:E, >> 0x042000-0x042fff:E, 0x043000-0x043fff:E, 0x044000-0x044fff:E, >> 0x045000-0x045fff:E, 0x046000-0x046fff:E, 0x047000-0x047fff:E, >> 0x048000-0x048fff:E, 0x049000-0x049fff:E, 0x04a000-0x04afff:E, >> 0x04b000-0x04bfff:E, 0x04c000-0x04cfff:E, 0x04d000-0x04dfff:E, >> 0x04e000-0x04efff:E, 0x04f000-0x04ffff:E, 0x050000-0x050fff:E, >> 0x051000-0x051fff:E, 0x052000-0x052fff:E, 0x053000-0x053fff:E, >> 0x054000-0x054fff:E, 0x055000-0x055fff:E, 0x056000-0x056fff:E, >> 0x057000-0x057fff:E, 0x058000-0x058fff:E, 0x059000-0x059fff:E, >> 0x05a000-0x05afff:E, 0x05b000-0x05bfff:E, 0x05c000-0x05cfff:E, >> 0x05d000-0x05dfff:E, 0x05e000-0x05efff:E, 0x05f000-0x05ffff:E, >> 0x060000-0x060fff:E, 0x061000-0x061fff:E, 0x062000-0x062fff:E, >> 0x063000-0x063fff:E, 0x064000-0x064fff:E, 0x065000-0x065fff:E, >> 0x066000-0x066fff:E, 0x067000-0x067fff:E, 0x068000-0x068fff:E, >> 0x069000-0x069fff:E, 0x06a000-0x06afff:E, 0x06b000-0x06bfff:E, >> 0x06c000-0x06cfff:E, 0x06d000-0x06dfff:E, 0x06e000-0x06efff:E, >> 0x06f000-0x06ffff:E, 0x070000-0x070fff:E, 0x071000-0x071fff:E, >> 0x072000-0x072fff:E, 0x073000-0x073fff:E, 0x074000-0x074fff:E, >> 0x075000-0x075fff:E, 0x076000-0x076fff:E, 0x077000-0x077fff:E, >> 0x078000-0x078fff:E, 0x079000-0x079fff:E, 0x07a000-0x07afff:E, >> 0x07b000-0x07bfff:E, 0x07c000-0x07cfff:E, 0x07d000-0x07dfff:E, >> 0x07e000-0x07efff:E, 0x07f000-0x07ffff:E >> Erase/write done. > > The chip is now erased, it doesn't contain BIOS/(U)EFI software anymore. > >> >> Restoring PCI config space for 00:01:0 reg 0x6d >> Restoring PCI config space for 00:01:0 reg 0x90 >> Restoring PCI config space for 00:01:0 reg 0x8c >> Restoring PCI config space for 00:01:0 reg 0x88 >> >> >> =================================================== >> >> If you want the output of another command, please ask me >> I finally flash my bios with a windows live disk so i don't want to take >> anyu risk but i want help > > Please do not reboot as your machine may have to be sent in for repair. > Unless you have made a backup readout file, we will supply a link for > the right BIOS rom. Here is the link: ftp://ftp.work.acer-euro.com/desktop/aspire_t180/bios/R01B4.zip and DOS/61AO427.BIN is the file that - I think - suits your board. > >> >> >> >> >> _______________________________________________ >> flashrom mailing list >> flashrom(a)flashrom.org >> http://www.flashrom.org/mailman/listinfo/flashrom

1 0

Re: [flashrom] flashrom -V
by Idwer Vollering 11 Jan '12

11 Jan '12

2012/1/11 Vince S <vince06fr(a)gmail.com>: > Hello > The output of flashrom -V : > > > flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci > 3.1.7, GCC 4.6.1, little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 736M loops per > second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1000 us, 10000 myus > = 10004 us, 4 myus = 5 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "Acer" > DMI string system-product-name: "Aspire T180" > DMI string system-version: "R01-A2" > DMI string baseboard-manufacturer: "Acer" > DMI string baseboard-product-name: "EM61SM/EM61PM " > DMI string baseboard-version: " " > DMI string chassis-type: "Desktop" > Found ITE Super I/O, ID 0x8726 on port 0x2e > Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. > This chipset is marked as untested. If you are using an up-to-date version > of flashrom please email a report to flashrom(a)flashrom.org including a > verbose (-V) log. Thank you! > Enabling flash write... This chipset is not really supported yet. > Guesswork... > ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 > Flash bus type is LPC > Found SMBus device 10de:03eb at 00:01:1 > MCP SPI BAR is at 0x00000000 > MCP SPI is not used. > Please send the output of "flashrom -V" to flashrom(a)flashrom.org with > your board name: flashrom -V as the subject to help us finish support for > your > chipset. Thanks. > OK. > This chipset supports the following protocols: LPC. > Super I/O ID 0x8726 is not on the list of flash capable controllers. > Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address > 0xfff80000. > Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > content > > Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > normal flash content, id2 is normal flash content > Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > normal flash content, id2 is normal flash content > Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 > 0x50, id1 is normal flash content > === > This flash part has status UNTESTED for operations: WRITE > The test status of this chip may have been updated in the latest development > version of flashrom. If you are running the latest development version, > please email a report to flashrom(a)flashrom.org if any of the above > operations > work correctly for you with this flash part. Please include the flashrom > output with the additional -V option for all operations you tested (-V, -Vr, > -Vw, -VE), and mention which mainboard or programmer you tested. > Please mention your board in the subject line. Thanks for your help! > > No operations were specified. > Restoring PCI config space for 00:01:0 reg 0x6d > Restoring PCI config space for 00:01:0 reg 0x90 > Restoring PCI config space for 00:01:0 reg 0x8c > Restoring PCI config space for 00:01:0 reg 0x88 > > > ======================================== > > Here the output of flashrom -VE : > > flashrom v0.9.4-r1394 on Linux 3.0.0-15-generic (x86_64), built with libpci > 3.1.7, GCC 4.6.1, little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 729M loops per > second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 990 us, 10000 myus = > 9955 us, 4 myus = 5 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "Acer" > DMI string system-product-name: "Aspire T180" > DMI string system-version: "R01-A2" > DMI string baseboard-manufacturer: "Acer" > DMI string baseboard-product-name: "EM61SM/EM61PM " > DMI string baseboard-version: " " > DMI string chassis-type: "Desktop" > Found ITE Super I/O, ID 0x8726 on port 0x2e > Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. > This chipset is marked as untested. If you are using an up-to-date version > of flashrom please email a report to flashrom(a)flashrom.org including a > verbose (-V) log. Thank you! > Enabling flash write... This chipset is not really supported yet. > Guesswork... > ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 > Flash bus type is LPC > Found SMBus device 10de:03eb at 00:01:1 > MCP SPI BAR is at 0x00000000 > MCP SPI is not used. > Please send the output of "flashrom -V" to flashrom(a)flashrom.org with > your board name: flashrom -V as the subject to help us finish support for > your > chipset. Thanks. > OK. > This chipset supports the following protocols: LPC. > Super I/O ID 0x8726 is not on the list of flash capable controllers. > Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50, > id1 is normal flash content > Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Found SST flash chip "SST49LF040B" (512 kB, LPC) at physical address > 0xfff80000. > Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > content > > Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > normal flash content, id2 is normal flash content > Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 is > normal flash content, id2 is normal flash content > Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 > 0x50, id1 is normal flash content > === > This flash part has status UNTESTED for operations: WRITE > The test status of this chip may have been updated in the latest development > version of flashrom. If you are running the latest development version, > please email a report to flashrom(a)flashrom.org if any of the above > operations > work correctly for you with this flash part. Please include the flashrom > output with the additional -V option for all operations you tested (-V, -Vr, > -Vw, -VE), and mention which mainboard or programmer you tested. > Please mention your board in the subject line. Thanks for your help! > Erasing and writing flash chip... Trying erase function 0... > 0x000000-0x000fff:E, 0x001000-0x001fff:E, 0x002000-0x002fff:E, > 0x003000-0x003fff:E, 0x004000-0x004fff:E, 0x005000-0x005fff:E, > 0x006000-0x006fff:E, 0x007000-0x007fff:E, 0x008000-0x008fff:E, > 0x009000-0x009fff:E, 0x00a000-0x00afff:E, 0x00b000-0x00bfff:E, > 0x00c000-0x00cfff:E, 0x00d000-0x00dfff:E, 0x00e000-0x00efff:E, > 0x00f000-0x00ffff:E, 0x010000-0x010fff:E, 0x011000-0x011fff:E, > 0x012000-0x012fff:E, 0x013000-0x013fff:E, 0x014000-0x014fff:E, > 0x015000-0x015fff:E, 0x016000-0x016fff:E, 0x017000-0x017fff:E, > 0x018000-0x018fff:E, 0x019000-0x019fff:E, 0x01a000-0x01afff:E, > 0x01b000-0x01bfff:E, 0x01c000-0x01cfff:E, 0x01d000-0x01dfff:E, > 0x01e000-0x01efff:E, 0x01f000-0x01ffff:E, 0x020000-0x020fff:E, > 0x021000-0x021fff:E, 0x022000-0x022fff:E, 0x023000-0x023fff:E, > 0x024000-0x024fff:E, 0x025000-0x025fff:E, 0x026000-0x026fff:E, > 0x027000-0x027fff:E, 0x028000-0x028fff:E, 0x029000-0x029fff:E, > 0x02a000-0x02afff:E, 0x02b000-0x02bfff:E, 0x02c000-0x02cfff:E, > 0x02d000-0x02dfff:E, 0x02e000-0x02efff:E, 0x02f000-0x02ffff:E, > 0x030000-0x030fff:E, 0x031000-0x031fff:E, 0x032000-0x032fff:E, > 0x033000-0x033fff:E, 0x034000-0x034fff:E, 0x035000-0x035fff:E, > 0x036000-0x036fff:E, 0x037000-0x037fff:E, 0x038000-0x038fff:E, > 0x039000-0x039fff:E, 0x03a000-0x03afff:E, 0x03b000-0x03bfff:E, > 0x03c000-0x03cfff:E, 0x03d000-0x03dfff:E, 0x03e000-0x03efff:E, > 0x03f000-0x03ffff:E, 0x040000-0x040fff:E, 0x041000-0x041fff:E, > 0x042000-0x042fff:E, 0x043000-0x043fff:E, 0x044000-0x044fff:E, > 0x045000-0x045fff:E, 0x046000-0x046fff:E, 0x047000-0x047fff:E, > 0x048000-0x048fff:E, 0x049000-0x049fff:E, 0x04a000-0x04afff:E, > 0x04b000-0x04bfff:E, 0x04c000-0x04cfff:E, 0x04d000-0x04dfff:E, > 0x04e000-0x04efff:E, 0x04f000-0x04ffff:E, 0x050000-0x050fff:E, > 0x051000-0x051fff:E, 0x052000-0x052fff:E, 0x053000-0x053fff:E, > 0x054000-0x054fff:E, 0x055000-0x055fff:E, 0x056000-0x056fff:E, > 0x057000-0x057fff:E, 0x058000-0x058fff:E, 0x059000-0x059fff:E, > 0x05a000-0x05afff:E, 0x05b000-0x05bfff:E, 0x05c000-0x05cfff:E, > 0x05d000-0x05dfff:E, 0x05e000-0x05efff:E, 0x05f000-0x05ffff:E, > 0x060000-0x060fff:E, 0x061000-0x061fff:E, 0x062000-0x062fff:E, > 0x063000-0x063fff:E, 0x064000-0x064fff:E, 0x065000-0x065fff:E, > 0x066000-0x066fff:E, 0x067000-0x067fff:E, 0x068000-0x068fff:E, > 0x069000-0x069fff:E, 0x06a000-0x06afff:E, 0x06b000-0x06bfff:E, > 0x06c000-0x06cfff:E, 0x06d000-0x06dfff:E, 0x06e000-0x06efff:E, > 0x06f000-0x06ffff:E, 0x070000-0x070fff:E, 0x071000-0x071fff:E, > 0x072000-0x072fff:E, 0x073000-0x073fff:E, 0x074000-0x074fff:E, > 0x075000-0x075fff:E, 0x076000-0x076fff:E, 0x077000-0x077fff:E, > 0x078000-0x078fff:E, 0x079000-0x079fff:E, 0x07a000-0x07afff:E, > 0x07b000-0x07bfff:E, 0x07c000-0x07cfff:E, 0x07d000-0x07dfff:E, > 0x07e000-0x07efff:E, 0x07f000-0x07ffff:E > Erase/write done. The chip is now erased, it doesn't contain BIOS/(U)EFI software anymore. > > Restoring PCI config space for 00:01:0 reg 0x6d > Restoring PCI config space for 00:01:0 reg 0x90 > Restoring PCI config space for 00:01:0 reg 0x8c > Restoring PCI config space for 00:01:0 reg 0x88 > > > =================================================== > > If you want the output of another command, please ask me > I finally flash my bios with a windows live disk so i don't want to take > anyu risk but i want help Please do not reboot as your machine may have to be sent in for repair. Unless you have made a backup readout file, we will supply a link for the right BIOS rom. > > > > > _______________________________________________ > flashrom mailing list > flashrom(a)flashrom.org > http://www.flashrom.org/mailman/listinfo/flashrom

1 0

Re: [flashrom] flashrom -V
by Stefan Tauner 11 Jan '12

11 Jan '12

On Fri, 6 Jan 2012 14:12:18 +0100 Vince S <vince06fr(a)gmail.com> wrote: > probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal > flash content, id2 is normal flash content > Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 > is normal flash content, id2 is normal flash content > Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x49, id2 0x4d, id1 > is normal flash content, id2 is normal flash content > Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 > parity violation, id1 is normal flash content, id2 is normal flash content > Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf, id2 0x50 > Found SST flash chip "SST49LF040B" (512 kB, LPC). > No operations were specified. > Restoring PCI config space for 00:01:0 reg 0x6d > Restoring PCI config space for 00:01:0 reg 0x90 > Restoring PCI config space for 00:01:0 reg 0x8c > Restoring PCI config space for 00:01:0 reg 0x88 > > > Thanks for your work hey there! thanks for your slightly mangled report ;) could you please resend the whole thing if it is still available to you, thanks. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

[commit] r1484 - trunk
by repository service 11 Jan '12

11 Jan '12

Author: hailfinger Date: Wed Jan 11 03:10:11 2012 New Revision: 1484 URL: http://flashrom.org/trac/flashrom/changeset/1484 Log: Postpone layout file reading Layout file reading should happen after option parsing like all other file accesses. Guard against multiple --layout parameters. Followup fix for r1483: Remove -m short option from getopt. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Acked-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Modified: trunk/cli_classic.c Modified: trunk/cli_classic.c ============================================================================== --- trunk/cli_classic.c Wed Jan 4 01:48:27 2012 (r1483) +++ trunk/cli_classic.c Wed Jan 11 03:10:11 2012 (r1484) @@ -177,7 +177,7 @@ enum programmer prog = PROGRAMMER_INVALID; int ret = 0; - static const char optstring[] = "r:Rw:v:nVEfc:m:l:i:p:Lzh"; + static const char optstring[] = "r:Rw:v:nVEfc:l:i:p:Lzh"; static const struct option long_options[] = { {"read", 1, NULL, 'r'}, {"write", 1, NULL, 'w'}, @@ -198,6 +198,7 @@ }; char *filename = NULL; + char *layoutfile = NULL; char *tempstr = NULL; char *pparam = NULL; @@ -273,9 +274,12 @@ force = 1; break; case 'l': - tempstr = strdup(optarg); - if (read_romlayout(tempstr)) + if (layoutfile) { + fprintf(stderr, "Error: --layout specified " + "more than once. Aborting.\n"); cli_classic_abort_usage(); + } + layoutfile = strdup(optarg); break; case 'i': tempstr = strdup(optarg); @@ -373,9 +377,6 @@ cli_classic_abort_usage(); } - if (process_include_args()) - cli_classic_abort_usage(); - /* FIXME: Print the actions flashrom will take. */ if (list_supported) { @@ -390,6 +391,11 @@ } #endif + if (layoutfile && read_romlayout(layoutfile)) + cli_classic_abort_usage(); + if (process_include_args()) + cli_classic_abort_usage(); + /* Does a chip with the requested name exist in the flashchips array? */ if (chip_to_probe) { for (flash = flashchips; flash && flash->name; flash++)

1 0

Re: [flashrom] I lost my backup image and now my pc doesn't start...!
by Stefan Tauner 11 Jan '12

11 Jan '12

On Tue, 10 Jan 2012 07:54:04 +0200 İlhan Kahraman <ilhan805(a)gmail.com> wrote: > Hello, > I think, I exaggerated things a little bit, due to excitement of my > inoperative mother board. The fan of cpu is working. I noticed that the > fans are working, in my latter flashing attempts, which I tried later than > I e-mailed you. The problem is that it is rotating in a very low constant > rpm. hi again, hm... doesnt the fan spin up fully at power-on first and is then throttled down afterwards (by software)? this is usually done because not all fans have the same start up voltage. some start at 6V or even less, others need more than 10V (even if they continue spinning at lower levels after getting to speed once). this shouldnt be different even for 4-pin fans i think... > I am sorry about that misleading e-mail :( > if I am not bothering you, would I continue to share my adventure with you? > is the aim of this mailing group, that? well as long as it is related to flashrom, it is right. not sure if everyone subscribed to the list (>200 ppl) is interested in personal recovery stories though :) if you find a solution for your problem that might be interesting for others too, i'd love to hear it! good luck -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

ASRock AM2NF6G-VSTA (Nvidia MCP61): `flashrom -Vr` (r1483)
by Paul Menzel 11 Jan '12

11 Jan '12

Dear Flashrom folks, I tested the ASRock AM2NF6G-VSTA with an Nvidia MCP61 chipset. The output says, that the chipset is not fully supported so please tell me what I have to consider when testing writing. $ flashrom -V -r am2nf6g-vsta.bin […] DMI string system-manufacturer: "To Be Filled By O.E.M." DMI string system-product-name: "To Be Filled By O.E.M." DMI string system-version: "To Be Filled By O.E.M." DMI string baseboard-manufacturer: " " DMI string baseboard-product-name: "AM2NF6G-VSTA" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found chipset "NVIDIA MCP61" with PCI ID 10de:03e0. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... This chipset is not really supported yet. Guesswork... ISA/LPC bridge reg 0x8a contents: 0x00, bit 6 is 0, bit 5 is 0 Flash bus type is LPC Found SMBus device 10de:03eb at 00:01:1 MCP SPI BAR is at 0x40000000 Strange. MCP SPI BAR is valid, but chipset apparently doesn't have SPI enabled. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with your board name: flashrom -V as the subject to help us finish support for your chipset. Thanks. OK. The following protocols are supported: LPC. […] Reading seems to work. The difference between the read image to the downloaded file (1.20) from the ASRock [2] is minimal according to `bsdiff`. 00000000 42 53 44 49 46 46 34 30 42 00 00 00 00 00 00 00 2D 00 00 00 00 00 00 00 00 00 08 00 BSDIFF40B.......-........... 0000001C 00 00 00 00 42 5A 68 39 31 41 59 26 53 59 59 02 DA 4C 00 00 0E EC 41 71 38 00 20 01 ....BZh91AY&SYY..L....Aq8. . 00000038 00 40 00 40 20 01 00 20 00 31 00 D0 00 C5 32 19 36 A2 B1 39 12 48 15 EA BC D8 B4 74 .@.@ .. .1....2.6..9.H.....t 00000054 E8 C2 6F E2 EE 48 A7 0A 12 0B 20 5B 49 80 42 5A 68 39 31 41 59 26 53 59 35 50 66 AE ..o..H.... [I.BZh91AY&SY5Pf. 00000070 00 04 04 40 00 C4 00 00 08 20 00 30 CC 05 29 A6 10 0D 88 80 78 BB 92 29 C2 84 81 AA ...@..... .0..).....x..).... 0000008C 83 35 70 42 5A 68 39 17 72 45 38 50 90 00 00 00 00 .5pBZh9.rE8P..... Please find all log files attached. Thanks, Paul [1] http://www.asrock.com/MB/overview.asp?Model=AM2NF6G-VSTA [2] http://www.asrock.com/mb/download.asp?Model=AM2NF6G-VSTA&o=BIOS

2 3

[PATCH] add support for SFDP (JESD216)
by Stefan Tauner 10 Jan '12

10 Jan '12

Similar to ICH Hardware Sequencing this uses a generic struct flashchip element in flashchips.c with dummy values and a special probe function that fills the obtained values into that generic struct. Documentation used: http://www.jedec.org/standards-documents/docs/jesd216 (2011-04) W25Q32BV data sheet Revision F (2011-04-01) EN25QH16 data sheet Revision F (2011-06-01) todo: - handle programmers which have a problem with the dummy bytes needed - move the code from spi25.c to its own file - rephrase the 'default' message of get_erasefn_from_opcode so that it becomes universally usable? Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- chipdrivers.h | 1 + flash.h | 2 + flashchips.c | 24 ++++ flashchips.h | 1 + flashrom.c | 28 +++++- spi.h | 5 + spi25.c | 355 +++++++++++++++++++++++++++++++++++++++++++++++++++++++++ 7 files changed, 415 insertions(+), 1 deletions(-) diff --git a/chipdrivers.h b/chipdrivers.h index a1d0cd9..bbc403f 100644 --- a/chipdrivers.h +++ b/chipdrivers.h @@ -28,6 +28,7 @@ #include "flash.h" /* for chipaddr and flashctx */ /* spi.c, should probably be in spi_chip.c */ +int probe_spi_sfdp(struct flashctx *flash); int probe_spi_rdid(struct flashctx *flash); int probe_spi_rdid4(struct flashctx *flash); int probe_spi_rems(struct flashctx *flash); diff --git a/flash.h b/flash.h index e51b6d4..6bcae71 100644 --- a/flash.h +++ b/flash.h @@ -174,6 +174,8 @@ struct flashctx { struct registered_programmer *pgm; }; +typedef int (erasefunc_t)(struct flashctx *flash, unsigned int addr, unsigned int blocklen); + #define TEST_UNTESTED 0 #define TEST_OK_PROBE (1 << 0) diff --git a/flashchips.c b/flashchips.c index ca1c57f..f0fde20 100644 --- a/flashchips.c +++ b/flashchips.c @@ -8872,6 +8872,30 @@ const struct flashchip flashchips[] = { .read = read_memmapped, .voltage = {3000, 3600}, /* Also has 12V fast program */ }, + + { + .vendor = "Unknown", + .name = "SFDP device", + .bustype = BUS_SPI, + .manufacture_id = GENERIC_MANUF_ID, + .model_id = SFDP_DEVICE_ID, + /* We present our own "report this" text hence we do not + * want the default "This flash part has status UNTESTED..." + * text to be printed. */ + .tested = TEST_OK_PREW, + .probe = probe_spi_sfdp, + .read = spi_chip_read, + /* FIXME: some vendor extensions define this */ + .voltage = {}, + /* Everything below will be set by the probing function. */ + .page_size = 0, + .write = NULL, + .total_size = 0, + .feature_bits = 0, + .block_erasers = {}, + .unlock = NULL, + .printlock = NULL, + }, { .vendor = "Programmer", diff --git a/flashchips.h b/flashchips.h index 03efb86..1f2a8ca 100644 --- a/flashchips.h +++ b/flashchips.h @@ -36,6 +36,7 @@ #define GENERIC_MANUF_ID 0xffff /* Check if there is a vendor ID */ #define GENERIC_DEVICE_ID 0xffff /* Only match the vendor ID */ +#define SFDP_DEVICE_ID 0xfffe #define ALLIANCE_ID 0x52 /* Alliance Semiconductor */ #define ALLIANCE_AS29F002B 0x34 diff --git a/flashrom.c b/flashrom.c index f1a6165..38998dd 100644 --- a/flashrom.c +++ b/flashrom.c @@ -986,7 +986,33 @@ int probe_flash(struct registered_programmer *pgm, int startchip, * probe_flash() is the first one and thus no chip has been * found before. */ - if (startchip == 0 || fill_flash->model_id != GENERIC_DEVICE_ID) + if (startchip == 0 && fill_flash->model_id == SFDP_DEVICE_ID) { + msg_cinfo("===\n" + "SFDP has autodetected a flash chip which is " + "not natively supported by flashrom yet.\n"); + if (count_usable_erasers(fill_flash) == 0) + msg_cinfo("The standard operations read and " + "verify should work, but to support " + "erase, write and all other " + "possible features"); + else + msg_cinfo("All standard operations (read, " + "verify, erase and write) should " + "work, but to support all possible " + "features"); + + msg_cinfo(" we need to add them manually.\nYou " + "can help us by mailing us the output of " + "the following command to flashrom@flashrom." + "org: \n'flashrom -VV [plus the " + "-p/--programmer parameter (if needed)]" + "'\nThanks for your help!\n" + "===\n"); + } + + if (startchip == 0 || + ((fill_flash->model_id != GENERIC_DEVICE_ID) && + (fill_flash->model_id != SFDP_DEVICE_ID))) break; notfound: diff --git a/spi.h b/spi.h index b908603..5f07eae 100644 --- a/spi.h +++ b/spi.h @@ -40,6 +40,11 @@ #define JEDEC_REMS_OUTSIZE 0x04 #define JEDEC_REMS_INSIZE 0x02 +/* Read Serial Flash Discoverable Parameters (SFDP) */ +#define JEDEC_SFDP 0x5a +#define JEDEC_SFDP_OUTSIZE 0x05 /* 8b op, 24b addr, 8b dummy */ +/* JEDEC_SFDP_INSIZE : any length */ + /* Read Electronic Signature */ #define JEDEC_RES 0xab #define JEDEC_RES_OUTSIZE 0x04 diff --git a/spi25.c b/spi25.c index 3ce7f08..07c716a 100644 --- a/spi25.c +++ b/spi25.c @@ -23,6 +23,7 @@ */ #include <string.h> +#include <stdlib.h> #include "flash.h" #include "flashchips.h" #include "chipdrivers.h" @@ -115,6 +116,360 @@ int spi_write_disable(struct flashctx *flash) return spi_send_command(flash, sizeof(cmd), 0, cmd, NULL); } +static int spi_sfdp_wrapper(struct flashctx *flash, uint32_t address, uint8_t *buf, int len) +{ + int i, ret; + const unsigned char cmd[JEDEC_SFDP_OUTSIZE] = { + JEDEC_SFDP, + (address >> 16) & 0xff, + (address >> 8) & 0xff, + (address >> 0) & 0xff, + 0 + }; + msg_cspew("spi_sfdp_wrapper: addr=0x%x, len=%d, data:\n", address, len); + ret = spi_send_command(flash, sizeof(cmd), len, cmd, buf); + for (i = 0; i < len; i++) + msg_cspew(" 0x%02x", buf[i]); + msg_cspew("\n"); + return ret; +} + +/* FIXME: eventually something similar like this but more generic should be + * available to split up spi commands. use that then instead */ +static int spi_sfdp(struct flashctx *flash, uint32_t address, uint8_t *buf, int len) +{ + /* FIXME: this is wrong. */ + int maxstep = 8; + int ret = 0; + while (len > 0) { + int step = min(len, maxstep); + ret = spi_sfdp_wrapper(flash, address, buf, step); + if (ret) + return ret; + address += step; + buf += step; + len -= step; + } + return ret; +} + +struct sfdp_tbl_hdr { + uint8_t id; + uint8_t v_minor; + uint8_t v_major; + uint8_t len; + uint32_t ptp; /* 24b pointer */ +}; + +static int (*get_erasefn_from_opcode(uint8_t opcode)) (struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen) +{ + switch(opcode){ + case 0x00: + case 0xff: + /* Not specified, assuming "not supported". */ + return NULL; + case 0x20: + return &spi_block_erase_20; + break; + case 0x52: + return &spi_block_erase_52; + break; + case 0x60: + return &spi_block_erase_60; + break; + case 0xc7: + return &spi_block_erase_c7; + break; + case 0xd7: + return &spi_block_erase_d7; + break; + case 0xd8: + return &spi_block_erase_d8; + default: + msg_cinfo("%s: unknown opcode (0x%02x) in SFDP table. " + "Please report this at " + "flashrom(a)flashrom.org\n", + __func__, opcode); + return NULL; + } +} + +static int sfdp_fill_flash(struct flashctx *f, uint8_t *buf, uint16_t len) +{ + uint32_t tmp32; + uint8_t tmp8; + uint32_t total_size; /* in bytes */ + uint32_t bsize; + uint8_t opcode_4k = 0xFF; + int dw, j; + int (*erasefn) (struct flashctx *flash, unsigned int blockaddr, unsigned int blocklen); + + + msg_cdbg2("Parsing JEDEC SFDP parameter table...\n"); + if (len == 9 * 4) { + msg_cerr("%s: len out of spec\n", __func__); + return 1; + } + + /* 1. double word */ + dw = 0; + tmp32 = buf[(4 * dw) + 0]; + tmp32 |= ((unsigned int)buf[(4 * dw) + 1]) << 8; + tmp32 |= ((unsigned int)buf[(4 * dw) + 2]) << 16; + tmp32 |= ((unsigned int)buf[(4 * dw) + 3]) << 24; + + tmp8 = (tmp32 >> 17) & 0x3; + switch (tmp8) { + case 0x0: + msg_cdbg2(" 3-Byte only addressing.\n"); + break; + case 0x1: + msg_cdbg2(" 3-Byte (and optionally 4-Byte) addressing.\n"); + break; + case 0x2: + msg_cdbg(" 4-Byte only addressing not supported.\n"); + return 1; + default: + msg_cdbg(" Required addressing mode (0x%x) not supported.\n", + tmp8); + return 1; + } + + msg_cdbg2(" Writes to the status register have "); + if (tmp32 & (1 << 3)) { + f->unlock = spi_disable_blockprotect; + msg_cdbg2("to be enabled with "); + if (tmp32 & (1 << 4)) { + f->feature_bits = FEATURE_WRSR_WREN; + msg_cdbg2("WREN (0x06).\n"); + } else { + f->feature_bits = FEATURE_WRSR_EWSR; + msg_cdbg2("EWSR (0x50).\n"); + } + } else + msg_cdbg2("not to be especially enabled.\n"); + + msg_cdbg2(" Write granularity is "); + if (tmp32 & (1 << 2)) { + msg_cdbg2(" at least 64 B.\n"); + f->page_size = 64; + f->write = spi_chip_write_256; + } else { + msg_cdbg2(" 1 B only.\n"); + f->page_size = 256; /* ? */ + f->write = spi_chip_write_1; + } + + if ((tmp32 & 0x3) == 0x1) { + opcode_4k = (tmp32 >> 8) & 0xFF; /* will be dealt with later */ + } + + /* 2. double word */ + dw = 1; + tmp32 = buf[(4 * dw) + 0]; + tmp32 |= ((unsigned int)buf[(4 * dw) + 1]) << 8; + tmp32 |= ((unsigned int)buf[(4 * dw) + 2]) << 16; + tmp32 |= ((unsigned int)buf[(4 * dw) + 3]) << 24; + + if (tmp32 & (1 << 31)) { + msg_cdbg(" Flash chip size >= 4 Gb/500 MB not supported.\n"); + return 1; + } + total_size = (tmp32 & 0x7FFFFFFF) / 8; + f->total_size = total_size / 1024; + msg_cdbg2(" Flash chip size is %d kB.\n", f->total_size); + + dw = 8; + for(j = 0; j < 4; j++) { + /* 8 double words from the start + 2 words for every eraser */ + tmp32 = buf[(4 * dw) + (2 * j)]; + if (tmp32 == 0) { + msg_cdbg2(" Block eraser %d is unused.\n", j); + continue; + } + if (tmp32 >= 31) { + msg_cdbg2(" Block size of eraser %d (2^%d) is too big." + "\n", j, tmp32); + continue; + } + bsize = 1 << (tmp32); /* bsize = 2 ^ field */ + + tmp8 = buf[(4 * dw) + (2 * j) + 1]; + erasefn = get_erasefn_from_opcode(tmp8); + if (erasefn == NULL) + continue; + f->block_erasers[j].block_erase = erasefn; + f->block_erasers[j].eraseblocks[0].size = bsize; + f->block_erasers[j].eraseblocks[0].count = total_size/bsize; + msg_cdbg2(" Block eraser %d: %d x %d B with opcode 0x%02x\n", + j, total_size/bsize, bsize, tmp8); + /* If there is a valid 4k value in the last double words, + * we override the value from double word 1. */ + if (bsize == 4 * 1024) + opcode_4k = 0xFF; + } + if (opcode_4k != 0xFF && + ((erasefn = get_erasefn_from_opcode(opcode_4k)) != NULL)) { + for (j = 0; j < NUM_ERASEFUNCTIONS; j++) { + struct block_eraser eraser = f->block_erasers[j]; + if (eraser.eraseblocks[0].size != 0) + continue; + eraser.block_erase = erasefn; + eraser.eraseblocks[0].size = 4 * 1024; + eraser.eraseblocks[0].count = total_size/bsize; + msg_cdbg2(" Block eraser %d: %d x %d B with opcode " + "0x%02x\n", j, total_size/bsize, bsize, + opcode_4k); + break; + } + msg_cinfo("%s: Not enough space to store another eraser (j=%d)." + " Please report this at flashrom(a)flashrom.org\n", + __func__, j); + } + return 0; +} + +static int sfdp_fetch_pt(struct flashctx *flash, uint32_t addr, uint8_t *buf, uint16_t len) +{ + uint16_t i; + if (spi_sfdp(flash, addr, buf, len)) { + msg_cerr("Receiving SFDP parameter table failed.\n"); + return 1; + } + msg_cspew(" Parameter table contents:\n"); + for(i = 0; i < len; i++) { + if ((i % 8) == 0) { + msg_cspew(" 0x%03x: ", i); + } + msg_cspew(" 0x%02x", buf[i]); + if ((i % 8) == 7) { + msg_cspew("\n"); + continue; + } + if ((i % 8) == 3) { + msg_cspew(" "); + continue; + } + } + msg_cspew("\n"); + return 0; +} + +int probe_spi_sfdp(struct flashctx *flash) +{ + int ret = 0; + uint8_t buf[8]; + uint16_t tmp16; + uint32_t tmp32; + uint8_t nph; + /* need to limit the table loop by comparing i to uint8_t nph hence: */ + uint16_t i; + struct sfdp_tbl_hdr *hdrs; + uint8_t *hbuf; + uint8_t *tbuf; + + if (spi_sfdp(flash, 0x00, buf, 4)) { + msg_cerr("Receiving SFDP signature failed.\n"); + return 0; + } + tmp32 = buf[0]; + tmp32 |= ((unsigned int)buf[1]) << 8; + tmp32 |= ((unsigned int)buf[2]) << 16; + tmp32 |= ((unsigned int)buf[3]) << 24; + + msg_cdbg2("SFDP signature = 0x%08x (should be 0x50444653)\n", tmp32); + if (tmp32 != 0x50444653) { + msg_cdbg("No SFDP signature found.\n"); + return 0; + } + if (spi_sfdp(flash, 0x04, buf, 3)) { + msg_cerr("Receiving SFDP revision and number of parameter " + "headers (NPH) failed. "); + return 0; + } + msg_cdbg2("SFDP revision = %d.%d\n", buf[1], buf[0]); + nph = buf[3]; + msg_cdbg2("SFDP number of parameter headers (NPH) = %d (+ 1 mandatory)" + "\n", nph); + + /* Fetch all parameter headers, even if we don't use them all (yet). */ + hbuf = malloc(sizeof(struct sfdp_tbl_hdr) * (nph + 1)); + hdrs = malloc((nph + 1) * 8); + if (hbuf == NULL || hdrs == NULL ) { + msg_gerr("Out of memory!\n"); + exit(1); /* FIXME: shutdown gracefully */ + } + if (spi_sfdp(flash, 0x08, hbuf, (nph + 1) * 8)) { + msg_cerr("Receiving SFDP parameter table headers failed.\n"); + goto cleanup_hdrs; + } + + i = 0; + do{ + hdrs[i].id = hbuf[(8 * i) + 0]; + hdrs[i].v_minor = hbuf[(8 * i) + 1]; + hdrs[i].v_major = hbuf[(8 * i) + 2]; + hdrs[i].len = hbuf[(8 * i) + 3]; + hdrs[i].ptp = hbuf[(8 * i) + 4]; + hdrs[i].ptp |= ((unsigned int)hbuf[(8 * i) + 5]) << 8; + hdrs[i].ptp |= ((unsigned int)hbuf[(8 * i) + 6]) << 16; + msg_cdbg2("SFDP parameter table header %d/%d:\n", i, nph); + msg_cdbg2(" ID 0x%02x, version %d.%d\n", hdrs[i].id, + hdrs[i].v_major, hdrs[i].v_minor); + tmp16 = hdrs[i].len * 4; + tmp32 = hdrs[i].ptp; + msg_cdbg2(" Length %d B, Parameter Table Pointer 0x%06x\n", + tmp16, tmp32); + + if (tmp16 + tmp32 > UINT16_MAX) { + msg_cerr("SFDP Parameter Table %d supposedly " + "overflows addressable SFDP area. This most\n" + "probably indicates a corrupt SFDP parameter " + "table header. Aborting SFDP probe!\n", i); + ret = 0; + goto cleanup_hdrs; + } + + tbuf = malloc(tmp16); + if (tbuf == NULL) { + msg_gerr("Out of memory!\n"); + exit(1); /* FIXME: shutdown gracefully */ + } + if (sfdp_fetch_pt(flash, tmp32, tbuf, tmp16)){ + msg_cerr("Fetching SFDP parameter table %d failed.\n", + i); + free(tbuf); + break; + } + if (i == 0) { /* Mandatory JEDEC SFDP parameter table */ + if (hdrs[i].id != 0) + msg_cdbg("ID of the mandatory JEDEC SFDP " + "parameter table is not 0 as demanded " + "by JESD216 (warning only).\n"); + + if (hdrs[i].len != (9 * 4)) { + msg_cdbg("Length of the mandatory JEDEC SFDP " + "parameter table is not 24 B as " + "demanded by JESD216.\n"); + if (hdrs[i].len == (4 * 4)) + msg_cdbg("It seems like it is the " + "preliminary Intel version of " + "SFDP, which we don't support." + "\n"); + } else if (sfdp_fill_flash(flash, tbuf, tmp16) == 0) + ret = 1; + } + + free(tbuf); + i++; + } while(i <= nph); + +cleanup_hdrs: + free(hdrs); + free(hbuf); + return ret; +} + static int probe_spi_rdid_generic(struct flashctx *flash, int bytes) { unsigned char readarr[4]; -- 1.7.1

1 0

← Newer
1
...
7
8
9
10
11
12
13
14
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom January 2012