OpenBIOS

openbios@openbios.org

4297 discussions

BINGO!
by James V Hendricks 06 Jul '00

06 Jul '00

Procedure: 1) Load Intel L440GX Standard BIOS 2) Switch the BIOS recovery jumper on (while system is running) 3) Get to the LILO prompt and reboot processor 0 (leave proc 1 running!) 4) Load LinuxBIOS SMP kernel 5) Switch the BIOS recovery jumper off (while system is running) 6) Reboot processor 1 7) Get Linux to 0010:00100000 and set BX to 0x0 (workaround -- this should be in LinuxBIOS). 8) Run hit F5 and look at the (framebuffer's) penguins!!! (For the ACL guys, check out the VA slate on my workbench.) Ron: We are good to go!! It is pretty obvious to me that processor 2 needs to run the MTRR init code; how do you want to do this? Perhaps an #ifdef LINUXBIOS in the kernel, or do you want to do a startup IPI? {Free,Open}BIOS lists: Does anyone know why we have to set BX to 0x0? Does anyone know why we get 'unexpected IRQ trap at vector 31.' when we calibrate the delay loops (on both processors)? Cheers. - James Linux version 2.4.0-test2 (jimi@rockhopper1) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #18 SMP Sun Jul 2 18:07:05 MDT 2000. BIOS-provided physical RAM map:. e820: 000000000009f000 @ 0000000000000000 (usable). e820: 0000000003e00000 @ 0000000000100000 (usable). Scan SMP from c0000000 for 1024 bytes.. found SMP MP-table at 00000000. hm, page 00000000 reserved twice.. On node 0 totalpages: 16128. zone(0): 4096 pages.. zone(1): 12032 pages.. zone(2): 0 pages.. Intel MultiProcessor Specification v1.4. Virtual Wire compatibility mode.. Default MP configuration #5. Processor #0 Pentium(tm) Pro APIC version 16. Floating point unit present.. Machine Exception supported.. 64 bit compare & exchange supported.. Internal APIC present.. Processor #1 Pentium(tm) Pro APIC version 16. Floating point unit present.. Machine Exception supported.. 64 bit compare & exchange supported.. Internal APIC present.. Bus #0 is ISA . Bus #1 is PCI . I/O APIC #2 Version 16 at 0xFEC00000.. Int: type 0, pol 0, trig 0, bus 0, IRQ 00, APIC ID 2, APIC INT 02. Int: type 0, pol 0, trig 0, bus 0, IRQ 01, APIC ID 2, APIC INT 01. Int: type 0, pol 0, trig 0, bus 0, IRQ 03, APIC ID 2, APIC INT 03. Int: type 0, pol 0, trig 0, bus 0, IRQ 04, APIC ID 2, APIC INT 04. Int: type 0, pol 0, trig 0, bus 0, IRQ 05, APIC ID 2, APIC INT 05. Int: type 0, pol 0, trig 0, bus 0, IRQ 06, APIC ID 2, APIC INT 06. Int: type 0, pol 0, trig 0, bus 0, IRQ 07, APIC ID 2, APIC INT 07. Int: type 0, pol 0, trig 0, bus 0, IRQ 08, APIC ID 2, APIC INT 08. Int: type 0, pol 0, trig 0, bus 0, IRQ 09, APIC ID 2, APIC INT 09. Int: type 0, pol 0, trig 0, bus 0, IRQ 0a, APIC ID 2, APIC INT 0a. Int: type 0, pol 0, trig 0, bus 0, IRQ 0b, APIC ID 2, APIC INT 0b. Int: type 0, pol 0, trig 0, bus 0, IRQ 0c, APIC ID 2, APIC INT 0c. Int: type 0, pol 0, trig 0, bus 0, IRQ 0d, APIC ID 2, APIC INT 0d. Int: type 0, pol 0, trig 0, bus 0, IRQ 0e, APIC ID 2, APIC INT 0e. Int: type 0, pol 0, trig 0, bus 0, IRQ 0f, APIC ID 2, APIC INT 0f. Int: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID 2, APIC INT 00. Lint: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 00. Lint: type 1, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 01. Processors: 2. mapped APIC to ffffe000 (fee00000). mapped IOAPIC to ffffd000 (fec00000). Kernel command line: root=/dev/hda1 single. Initializing CPU#0. Detected 497445265 Hz processor.. Console: colour dummy device 80x25. unexpected IRQ trap at vector 31. Calibrating delay loop... unexpected IRQ trap at vector 31. 989.59 BogoMIPS. unexpected IRQ trap at vector 31. Memory: 61888k/64512k available (723k kernel code, 2236k reserved, 83k data, 72k init, 0k highmem). Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes). Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes). Page-cache hash table entries: 16384 (order: 4, 65536 bytes). kmem_create: Poisoning requested, but con given - bdev_cache. Inode-cache hash table entries: 4096 (order: 3, 32768 bytes). kmem_create: Poisoning requested, but con given - inode_cache. CPU serial number disabled.. Checking 386/387 coupling... OK, FPU using exception 16 error reporting.. Enabling fast FPU save and restore... done.. Enabling unmasked SIMD FPU exception support... done.. Checking SIMD FPU exceptions... OK, SIMD FPU using exception 19 error reporting.. Checking 'hlt' instruction... OK.. POSIX conformance testing by UNIFIX. mtrr: v1.36 (20000221) Richard Gooch (rgooch(a)atnf.csiro.au). CPU serial number disabled.. CPU0: Intel Pentium III (Katmai) stepping 03. per-CPU timeslice cutoff: 0.00 usecs.. Getting VERSION: 40011. Getting VERSION: 40011. Getting LVT0: 700. Getting LVT1: 400. enabled ExtINT on CPU#0. ESR value before enabling vector: 00000000. ESR value after enabling vector: 00000000. CPU present map: 3. Booting processor 1/0 eip 2000. Setting warm reset code and vector.. 1.. 2.. 3.. Asserting INIT.. Waiting for send to finish.... +Deasserting INIT.. Waiting for send to finish.... +#startup loops: 2.. Sending STARTUP #1.. After apic_write.. Startup point 1.. Waiting for send to finish.... +Initializing CPU#1. Sending STARTUP #2.. After apic_write.. Startup point 1.. Waiting for send to finish.... +CPU#1 (phys ID: 0) waiting for CALLOUT. After Startup.. Before Callout 1.. After Callout 1.. CALLIN, before setup_local_APIC().. masked ExtINT on CPU#1. ESR value before enabling vector: 00000000. ESR value after enabling vector: 00000000. Calibrating delay loop... unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. unexpected IRQ trap at vector 31. 992.87 BogoMIPS. Stack at about c112bfbc. CPU serial number disabled.. unexpected IRQ trap at vector 31. OK.. CPU1: Intel Pentium III (Katmai) stepping 03. CPU has booted.. Before bogomips.. Total of 2 processors activated (1982.46 BogoMIPS).. Before bogocount - setting activated=1.. Boot done.. ENABLING IO-APIC IRQs. ...changing IO-APIC physical APIC ID to 2 ... ok.. Synchronizing Arb IDs.. init IO_APIC IRQs. IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.. ..TIMER: vector=49 pin1=2 pin2=0. activating NMI Watchdog ... done.. number of MP IRQ sources: 16.. number of IO-APIC #2 registers: 24.. testing the IO APIC........................ . IO APIC #2....... .... register #00: 02000000. ....... : physical APIC id: 02. .... register #01: 00170011. ....... : max redirection entries: 0017. ....... : IO APIC version: 0011. .... register #02: 00000000. ....... : arbitration: 00. .... IRQ redirection table:. NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect: . 00 000 00 1 0 0 0 0 0 0 00. 01 003 03 0 0 0 0 0 1 1 39. 02 003 03 0 0 0 0 0 1 1 31. 03 003 03 0 0 0 0 0 1 1 41. 04 003 03 0 0 0 0 0 1 1 49. 05 003 03 0 0 0 0 0 1 1 51. 06 003 03 0 0 0 0 0 1 1 59. 07 003 03 0 0 0 0 0 1 1 61. 08 003 03 0 0 0 0 0 1 1 69. 09 003 03 0 0 0 0 0 1 1 71. 0a 003 03 0 0 0 0 0 1 1 79. 0b 003 03 0 0 0 0 0 1 1 81. 0c 003 03 0 0 0 0 0 1 1 89. 0d 000 00 1 0 0 0 0 0 0 00. 0e 003 03 0 0 0 0 0 1 1 91. 0f 003 03 0 0 0 0 0 1 1 99. 10 000 00 1 0 0 0 0 0 0 00. 11 000 00 1 0 0 0 0 0 0 00. 12 000 00 1 0 0 0 0 0 0 00. 13 000 00 1 0 0 0 0 0 0 00. 14 000 00 1 0 0 0 0 0 0 00. 15 000 00 1 0 0 0 0 0 0 00. 16 000 00 1 0 0 0 0 0 0 00. 17 000 00 1 0 0 0 0 0 0 00. IRQ to pin mappings:. IRQ0 -> 2. IRQ1 -> 1. IRQ3 -> 3. IRQ4 -> 4. IRQ5 -> 5. IRQ6 -> 6. IRQ7 -> 7. IRQ8 -> 8. IRQ9 -> 9. IRQ10 -> 10. IRQ11 -> 11. IRQ12 -> 12. IRQ13 -> 13. IRQ14 -> 14. IRQ15 -> 15. .................................... done.. calibrating APIC timer .... ..... CPU clock speed is 497.3914 MHz.. ..... host bus clock speed is 99.4782 MHz.. cpu: 0, clocks: 994782, slice: 331594. CPU0<T0:994768,T1:663168,D:6,S:331594,C:994782>. cpu: 1, clocks: 994782, slice: 331594. CPU1<T0:994768,T1:331568,D:12,S:331594,C:994782>. checking TSC synchronization across CPUs: passed.. Setting commenced=1, go go go. mtrr: your CPUs had inconsistent fixed MTRR settings. mtrr: your CPUs had inconsistent variable MTRR settings. mtrr: your CPUs had inconsistent MTRRdefType settings. mtrr: probably your BIOS does not setup all CPUs. PCI: Using configuration type 1. PCI: Probing PCI hardware. Linux NET4.0 for Linux 2.3. Based upon Swansea University Computer Society NET3.039. kmem_create: Poisoning requested, but con given - skbuff_head_cache. Starting kswapd v1.6. PCI: No IRQ known for interrupt pin A of device 00:09.0. Probably buggy MP table.. matroxfb: Matrox Millennium II (PCI) detected. matroxfb: MTRR's turned on. matroxfb: 640x480x8bpp (virtual: 640x13081). matroxfb: framebuffer at 0xA5000000, mapped to 0xc4805000, size 8388608. Console: switching to colour frame buffer device 80x30. fb0: MATROX VGA frame buffer device. Uniform Multi-Platform E-IDE driver Revision: 6.31. ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx. hd0: C/H/S=0/0/0 from BIOS ignored. hda: 0MB, CHS=0/0/0. Real Time Clock Driver v1.10c. end_request: I/O error, dev 03:01 (hard disk), sector 2. EXT2-fs: unable to read superblock. Kernel panic: VFS: Unable to mount root fs on 03:01............. - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

5 8

L2 cache
by Ronald G Minnich 03 Jul '00

03 Jul '00

In case I did not mention it: we aren't turning on L2 cache. We need to figure this one out. All hints gratefully accepted ... ron - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

2 3

winfast 6300, PIII
by Ronald G Minnich 03 Jul '00

03 Jul '00

I just took the romimage for linuxbios and plugged it into the winfast 6300 board. This is the identical image to the one that works for the procomm bst1b. It works! we now have two sis630 mainboards up (but with no L2 ... :-( ) ron - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

1 0

L2 cache
by Ronald G Minnich 30 Jun '00

30 Jun '00

A quick run with lmbench shows we're not turning it on. Any ideas? ron - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

1 0

IO-APIC
by James Hendricks 30 Jun '00

30 Jun '00

I don't think our IO-APIC is enabled.. We tell it to set its ID to 2, but it continues to think its ID is F. Here is the kernel panic: ENABLING IO-APIC IRQs. ...changing IO-APIC physical APIC ID to 2 ... Kernel panic: could not set ID!. . In idle task - not syncing. APIC error interrupt on CPU#0, should never happen.. ... APIC ESR0: 00000000. ... APIC ESR1: 00000040. ... bit 6: Received Illegal Vector Does anyone know how to setup the IO-APIC correctly and/or know where I can find this information (Maciej, you wrote io_apic.c, right?)? Any help would be greatly appreciated. Thanks. - James >>>>>> Here is the full boot so far: Linux version 2.4.0-test1 (jimi@snaresland) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #7 SMP Mon Jun 26 16:46:02 MDT 2000. BIOS-provided physical RAM map:. e820: 000000000009f000 @ 0000000000000000 (usable). e820: 0000000003e00000 @ 0000000000100000 (usable). Scan SMP from c0000000 for 1024 bytes.. found SMP MP-table at 00000000. hm, page 00000000 reserved twice.. On node 0 totalpages: 16128. zone(0): 4096 pages.. zone(1): 12032 pages.. zone(2): 0 pages.. Intel MultiProcessor Specification v1.4. Virtual Wire compatibility mode.. Default MP configuration #5. Processor #0 Pentium(tm) Pro APIC version 16. Floating point unit present.. Machine Exception supported.. 64 bit compare & exchange supported.. Internal APIC present.. Processor #1 Pentium(tm) Pro APIC version 16. Floating point unit present.. Machine Exception supported.. 64 bit compare & exchange supported.. Internal APIC present.. Bus #0 is ISA . Bus #1 is PCI . I/O APIC #2 Version 16 at 0xFEC00000.. Int: type 0, pol 0, trig 0, bus 0, IRQ 00, APIC ID 2, APIC INT 02. Int: type 0, pol 0, trig 0, bus 0, IRQ 01, APIC ID 2, APIC INT 01. Int: type 0, pol 0, trig 0, bus 0, IRQ 03, APIC ID 2, APIC INT 03. Int: type 0, pol 0, trig 0, bus 0, IRQ 04, APIC ID 2, APIC INT 04. Int: type 0, pol 0, trig 0, bus 0, IRQ 05, APIC ID 2, APIC INT 05. Int: type 0, pol 0, trig 0, bus 0, IRQ 06, APIC ID 2, APIC INT 06. Int: type 0, pol 0, trig 0, bus 0, IRQ 07, APIC ID 2, APIC INT 07. Int: type 0, pol 0, trig 0, bus 0, IRQ 08, APIC ID 2, APIC INT 08. Int: type 0, pol 0, trig 0, bus 0, IRQ 09, APIC ID 2, APIC INT 09. Int: type 0, pol 0, trig 0, bus 0, IRQ 0a, APIC ID 2, APIC INT 0a. Int: type 0, pol 0, trig 0, bus 0, IRQ 0b, APIC ID 2, APIC INT 0b. Int: type 0, pol 0, trig 0, bus 0, IRQ 0c, APIC ID 2, APIC INT 0c. Int: type 0, pol 0, trig 0, bus 0, IRQ 0d, APIC ID 2, APIC INT 0d. Int: type 0, pol 0, trig 0, bus 0, IRQ 0e, APIC ID 2, APIC INT 0e. Int: type 0, pol 0, trig 0, bus 0, IRQ 0f, APIC ID 2, APIC INT 0f. Int: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID 2, APIC INT 00. Lint: type 3, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 00. Lint: type 1, pol 0, trig 0, bus 0, IRQ 00, APIC ID ff, APIC LINT 01. Processors: 2. mapped APIC to ffffe000 (fee00000). James: boot_cpu_id being set to 2016 from APIC_ID. mapped IOAPIC to ffffd000 (fec00000). Enabling extended fast FPU save and restore ... done.. Enabling KNI unmasked exception support ... done.. Kernel command line: root=/dev/hda1 ide0=reset. Initializing CPU#0. Detected 497445265 Hz processor.. Calibrating delay loop... 992.87 BogoMIPS. Memory: 61980k/64512k available (585k kernel code, 2144k reserved, 69k data, 156k init, 0k highmem). Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes). Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes). Page-cache hash table entries: 16384 (order: 4, 65536 bytes). kmem_create: Poisoning requested, but con given - bdev_cache. Inode-cache hash table entries: 4096 (order: 3, 32768 bytes). kmem_create: Poisoning requested, but con given - inode_cache. CPU serial number disabled.. Checking 386/387 coupling... OK, FPU using exception 16 error reporting.. Checking 'hlt' instruction... OK.. POSIX conformance testing by UNIFIX. mtrr: v1.36 (20000221) Richard Gooch (rgooch(a)atnf.csiro.au). CPU serial number disabled.. CPU0: Intel Pentium III (Katmai) stepping 03. per-CPU timeslice cutoff: 0.00 usecs.. Getting VERSION: 40011. Getting VERSION: 40011. Getting LVT0: 700. Getting LVT1: 400. enabled ExtINT on CPU#0. ESR value before enabling vector: 00000000. ESR value after enabling vector: 00000000. CPU present map: 3. Booting processor 1/0 eip 2000. Setting warm reset code and vector.. 1.. 2.. 3.. Asserting INIT.. Waiting for send to finish.... +Deasserting INIT.. Waiting for send to finish.... +#startup loops: 2.. Sending STARTUP #1.. After apic_write.. Startup point 1.. Waiting for send to finish.... +Initializing CPU#1. Sending STARTUP #2.. After apic_write.. Startup point 1.. CPU#1 (phys ID: 0) waiting for CALLOUT. Waiting for send to finish.... +After Startup.. Before Callout 1.. After Callout 1.. CALLIN, before setup_local_APIC().. masked ExtINT on CPU#1. ESR value before enabling vector: 00000000. ESR value after enabling vector: 00000000. Calibrating delay loop... 992.87 BogoMIPS. Stack at about c116dfbc. CPU serial number disabled.. OK.. CPU1: Intel Pentium III (Katmai) stepping 03. CPU has booted.. Before bogomips.. Total of 2 processors activated (1985.74 BogoMIPS).. Before bogocount - setting activated=1.. Boot done.. ENABLING IO-APIC IRQs. ...changing IO-APIC physical APIC ID to 2 ... Kernel panic: could not set ID!. . In idle task - not syncing. APIC error interrupt on CPU#0, should never happen.. ... APIC ESR0: 00000000. ... APIC ESR1: 00000040. ... bit 6: Received Illegal Vector - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

4 4

visitor
by ronnie-liu＠ali.com.tw 23 Jun '00

23 Jun '00

Hi: I found the OpenBIOS web site when surfing the internet. I am interesting in this topic. Is this project still going? Ronnie - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

2 1

RE: [OpenBIOS] Finding FlashROM chips?
by Jessen, Per 22 Jun '00

22 Jun '00

www.questlink.com regards, Per Jessen, ENIDAN Technologies, London > -----Original Message----- > From: Jeff Garzik [mailto:jgarzik@mandrakesoft.com] > Sent: 21 June 2000 16:06 > To: freebios-devel(a)sourceforge.net > Cc: openbios(a)elvis.informatik.uni-freiburg.de > Subject: [OpenBIOS] Finding FlashROM chips? > > > Can anybody point to a source of flashrom chips on the web? > Preferably > a US supplier since I don't want to ship overseas if I can avoid it.. > > Jeff > > > > > -- > Jeff Garzik | > Building 1024 | Free beer tomorrow. > MandrakeSoft, Inc. | > - > To unsubscribe: send mail to majordomo(a)freiburg.linux.de > with 'unsubscribe openbios' in the body of the message > - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

1 0

Re: Information on TIARA project
by Ollie Lho 21 Jun '00

21 Jun '00

"Larry G. Linde" wrote: > > We are working on a 540 design at present and need to start porting to the > 540/950 chipset. > > However we have not been able to find any off the shelf MB's with the 540 > yet. If you could get > Us the name of a existing 540 MB with the 950 that we could buy that would > help a lot. Also > And code/doc info in setup that required on the 540/950 would help as well. > > If you would like I will be in TW in about 2 weeks. I can stop by and say > hello and show you > What we are doing. > > -larry First of all, it is amazing (from our point of view) that without official support you could do such chip init stuff so clean, how did you do this ?? As you know we are working with FreeBIOS/LinuxBIOS project, we are also intrested in any similiar projects too. We will provide any support we can, we will provide you the necessary documents, BIOS source/pseudo code and hardware demo boards. As posted by Jeff Garzik et. al. on freebios list we think there is possibility to cooperate/merge these free bios projects. For 540+950 issue, there are two things to note. First is that, from business point of view, it seems that 540 chipset will not in mass production in the near future so it would be very difficult to find a 540 M/B in the market. We are rather focusing on 630 and the upcomming 730 series. As far as I know there is only WinFast 5400MA avaliable in Taiwan market. The second is that, of course we want our whole product line fully supported. I am personally planing to have full support (i.e. boot from cold power up without BIOS) for the following combination in the end of August (possible ??) 630/540 single chip + 950 LPC 620/530 north + 5595 sourth + 6801 SuperIO so we need somebody to "port" or try the current implementation on these different platforms. Finally, it glad that you are going to visit Taiwan. If you have time, please arrange to visit SiS and demo your work. We can show you how/what we have done on LinuxBIOS side. Ollie - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

5 5

another free bios project
by gram wilson 21 Jun '00

21 Jun '00

I just came across this project at SourceForge: Talkware TIARA, an Openbios/GRUB/PFORTH composite, BIOS replacement. Boots an unmodifed linux kernel from an IDE drive or ethernet, using only 128kb of flash. Works with INTEL/AMD K6/2-450, SiS 530/5595 and 8139 enet. VGA & Serial console supported. and was wondering if anybody had heard of it? It got me thinking that maybe all of the free bios developers (this project, freebios, openbios, linuxbios) should get together and collaborate on features. This way there would be more developers, which could mean accelerated development, better features, and more testing. Also, I would like to thank all of the people who work on these projects now, because a free/open source bios is something we all really need. -gram - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

5 5

TIARA URL
by Ed Dantes 20 Jun '00

20 Jun '00

Hi Joerg The only URL for TIARA seems to be http://sourceforge.net/projects/utcboot/ Have fun Ed - To unsubscribe: send mail to majordomo(a)freiburg.linux.de with 'unsubscribe openbios' in the body of the message

1 0

Jump to page: