Author: wmb Date: 2009-04-16 22:51:50 +0200 (Thu, 16 Apr 2009) New Revision: 1147
Modified: dev/mmc/sdhci/sdhci.fth Log: SDHCI - clarified commentary to make it easier to find command numbers
Modified: dev/mmc/sdhci/sdhci.fth =================================================================== --- dev/mmc/sdhci/sdhci.fth 2009-04-16 20:41:04 UTC (rev 1146) +++ dev/mmc/sdhci/sdhci.fth 2009-04-16 20:51:50 UTC (rev 1147) @@ -349,22 +349,22 @@ d# 16 instance buffer: csd headers
-: reset-card ( -- ) 0 0 0 cmd 0 to rca 1 ms ; \ 0 - +: reset-card ( -- ) 0 0 0 cmd 0 to rca 1 ms ; \ CMD0
-: send-op-cond ( voltage-range -- ocr ) h# 0102 0 cmd response ; \ R3 +: send-op-cond ( voltage-range -- ocr ) h# 0102 0 cmd response ; \ CMD1 R3
\ Get card ID; Result is in cid buffer -: get-all-cids ( -- ) 0 h# 0209 0 cmd cid get-response136 ; \ 2 R2 +: get-all-cids ( -- ) 0 h# 0209 0 cmd cid get-response136 ; \ CMD2 R2
\ Get relative card address -: get-rca ( -- ) 0 h# 031a 0 cmd response h# ffff0000 and to rca ; \ 3 R6 - SD -: set-rca ( rca -- ) to rca rca h# 031a 0 cmd ; \ 3 R1 - MMC +: get-rca ( -- ) 0 h# 031a 0 cmd response h# ffff0000 and to rca ; \ CMD3 R6 - SD +: set-rca ( rca -- ) to rca rca h# 031a 0 cmd ; \ CMD3 R1 - MMC
-: set-dsr ( -- ) 0 h# 0400 0 cmd ; \ 4 - UNTESTED +: set-dsr ( -- ) 0 h# 0400 0 cmd ; \ CMD4 - UNTESTED
\ 5 - CMD5 is for SDIO. It is defined below in the SDIO section.
-\ cmd6 (R1) is switch-function. It can be used to enter high-speed mode +\ CMD6 (R1) is switch-function. It can be used to enter high-speed mode : switch-function ( arg -- adr ) scratch-buf d# 64 d# 64 (dma-setup) h# 063b h# 11 cmd ( response drop ) @@ -373,24 +373,24 @@ scratch-buf ;
-: deselect-card ( -- ) 0 h# 0700 0 cmd ; \ 7 - with null RCA -: select-card ( -- ) rca h# 071b 0 cmd ; \ 7 R1b +: deselect-card ( -- ) 0 h# 0700 0 cmd ; \ CMD7 - with null RCA +: select-card ( -- ) rca h# 071b 0 cmd ; \ CMD7 R1b
-: send-if-cond ( -- ) h# 1aa h# 081a 0 cmd ( response h# 1aa <> if ." Error" then ) ; \ 8 R7 (SD) +: send-if-cond ( -- ) h# 1aa h# 081a 0 cmd ( response h# 1aa <> if ." Error" then ) ; \ CMD8 R7 (SD)
-\ : send-ext-csd ( adr -- ) 0 h# 0812 0 cmd ; \ 8 R1 (MMC) Untested - requires data transfer +\ : send-ext-csd ( adr -- ) 0 h# 0812 0 cmd ; \ CMD8 R1 (MMC) Untested - requires data transfer
\ Get Card-specific data -: get-csd ( -- ) rca h# 0909 0 cmd csd get-response136 ; \ 9 R2 -: get-cid ( -- ) rca h# 0a09 0 cmd cid get-response136 ; \ 10 R2 UNTESTED +: get-csd ( -- ) rca h# 0909 0 cmd csd get-response136 ; \ CMD9 R2 +: get-cid ( -- ) rca h# 0a09 0 cmd cid get-response136 ; \ CMD10 R2 UNTESTED
-: stop-transmission ( -- ) rca h# 0c1b 0 cmd ; \ 12 R1b UNTESTED +: stop-transmission ( -- ) rca h# 0c1b 0 cmd ; \ CMD12 R1b UNTESTED
-: get-status ( -- status ) rca h# 0d1a 0 cmd response ; \ 13 R1 UNTESTED +: get-status ( -- status ) rca h# 0d1a 0 cmd response ; \ CMD13 R1 UNTESTED
-: go-inactive ( -- ) rca h# 0f00 0 cmd ; \ 15 - UNTESTED +: go-inactive ( -- ) rca h# 0f00 0 cmd ; \ CMD15 - UNTESTED
-: set-blocklen ( blksize -- ) h# 101a 0 cmd ; \ 16 R1 SET_BLOCKLEN +: set-blocklen ( blksize -- ) h# 101a 0 cmd ; \ CMD16 R1 SET_BLOCKLEN
\ Data transfer mode bits for register 0c (only relevant for reads, writes, \ and switch-function) @@ -401,46 +401,46 @@ \ 10.0000 direction: 1 for read, 0 for write \ 20.0000 multi (set for multiple-block transfers)
-: read-single ( address -- ) h# 113a h# 13 cmd ; \ 17 R1 READ_SINGLE_BLOCK -: read-multiple ( address -- ) h# 123a h# 37 cmd ; \ 18 R1 READ_MULTIPLE -: write-single ( address -- ) h# 183a h# 03 cmd ; \ 24 R1 WRITE_SINGLE_BLOCK -: write-multiple ( address -- ) h# 193a h# 27 cmd ; \ 25 R1 WRITE_MULTIPLE +: read-single ( address -- ) h# 113a h# 13 cmd ; \ CMD17 R1 READ_SINGLE_BLOCK +: read-multiple ( address -- ) h# 123a h# 37 cmd ; \ CMD18 R1 READ_MULTIPLE +: write-single ( address -- ) h# 183a h# 03 cmd ; \ CMD24 R1 WRITE_SINGLE_BLOCK +: write-multiple ( address -- ) h# 193a h# 27 cmd ; \ CMD25 R1 WRITE_MULTIPLE
-: program-csd ( -- ) 0 h# 1b1a 0 cmd ; \ R1 27 UNTESTED -: protect ( group# -- ) h# 1c1b 0 cmd ; \ R1b 28 UNTESTED -: unprotect ( group# -- ) h# 1d1b 0 cmd ; \ R1b 29 UNTESTED -: protected? ( group# -- 32-bits ) h# 1e1a cmd response ; \ 30 R1 UNTESTED +: program-csd ( -- ) 0 h# 1b1a 0 cmd ; \ CMD27 R1 UNTESTED +: protect ( group# -- ) h# 1c1b 0 cmd ; \ CMD28 R1b UNTESTED +: unprotect ( group# -- ) h# 1d1b 0 cmd ; \ CMD29 R1b UNTESTED +: protected? ( group# -- 32-bits ) h# 1e1a cmd response ; \ CMD30 R1 UNTESTED
: erase-blocks ( block# #blocks -- ) \ UNTESTED dup 0= if 2drop exit then 1- bounds ( last first ) - h# 201a 0 cmd ( last ) \ cmd32 - R1 - h# 211a 0 cmd ( ) \ cmd33 - R1 - h# 261b 0 cmd \ cmd38 - R1b (wait for busy) + h# 201a 0 cmd ( last ) \ CMD32 - R1 + h# 211a 0 cmd ( ) \ CMD33 - R1 + h# 261b 0 cmd \ CMD38 - R1b (wait for busy) ;
-\ cmd40 is MMC +\ CMD40 is MMC
\ See table 4-5 in sandisk spec -\ : lock/unlock ( -- ) 0 h# 2a1a 0 cmd ; \ 42 R1 LOCK_UNLOCK not sure how it works +\ : lock/unlock ( -- ) 0 h# 2a1a 0 cmd ; \ CMD42 R1 LOCK_UNLOCK not sure how it works
-: app-prefix ( -- ) rca h# 371a 0 cmd ; \ 55 R1 app-specific command prefix +: app-prefix ( -- ) rca h# 371a 0 cmd ; \ CMD55 R1 app-specific command prefix
-: set-bus-width ( mode -- ) app-prefix h# 61a 0 cmd ; \ a6 R1 Set mode +: set-bus-width ( mode -- ) app-prefix h# 61a 0 cmd ; \ ACMD6 R1 Set mode
-: set-oc ( ocr -- ocr' ) app-prefix h# 2902 0 cmd response ; \ a41 R3 +: set-oc ( ocr -- ocr' ) app-prefix h# 2902 0 cmd response ; \ ACMD41 R3
\ This sends back 512 bits in a single data block. -: app-get-status ( -- status ) app-prefix 0 h# 0d1a h# 12 cmd response ; \ a13 R1 UNTESTED +: app-get-status ( -- status ) app-prefix 0 h# 0d1a h# 12 cmd response ; \ ACMD13 R1 UNTESTED
-: get-#write-blocks ( -- n ) app-prefix 0 h# 161a 0 cmd response ; \ a22 R1 UNTESTED +: get-#write-blocks ( -- n ) app-prefix 0 h# 161a 0 cmd response ; \ ACMD22 R1 UNTESTED
\ You might want to turn this off for data transfer, as it controls \ a resistor on one of the data lines -: set-card-detect ( on/off -- ) app-prefix h# 2a1a 0 cmd ; \ a42 R1 UNTESTED +: set-card-detect ( on/off -- ) app-prefix h# 2a1a 0 cmd ; \ ACMD42 R1 UNTESTED : get-scr ( -- adr ) scratch-buf d# 8 d# 8 (dma-setup) - app-prefix 0 h# 333a h# 11 cmd ( response drop ) \ a51 R1 + app-prefix 0 h# 333a h# 11 cmd ( response drop ) \ ACMD51 R1 2 wait dma-release scratch-buf @@ -451,11 +451,11 @@ \ We can't set the 10 bit in the cmd register here, because the R4 response \ format doesn't echo the command index in the response.
-: io-send-op-cond ( voltage-range -- ocr ) h# 050a 0 cmd response ; \ 5 R4 +: io-send-op-cond ( voltage-range -- ocr ) h# 050a 0 cmd response ; \ CMD5 R4 (SDIO)
: >io-arg ( reg# function# -- arg ) 7 and d# 28 lshift or ;
-\ The following are CMD52 variants +\ The following are CMD52 (SDIO) variants \ Flags: 80:CRC_ERROR 40:ILLEGAL_COMMAND 30:IO_STATE (see spec) \ 08:ERROR 04:reserved 02:INVALID_FUNCTION# 01:OUT_OF_RANGE : io-b@ ( reg# function# -- value flags ) @@ -471,7 +471,7 @@ response wbsplit ;
-\ CMD53 - IO_RW_EXTENDED +\ CMD53 (SDIO) - IO_RW_EXTENDED \ These commands - io-{read,write}-{bytes,blocks} will need to be \ enclosed in a method like r/w-blocks, in order to set up the DMA hardware.
openfirmware@openfirmware.info
-
svn＠openfirmware.info