Author: wmb Date: Fri Sep 23 06:59:53 2011 New Revision: 2527 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2527
Log: OLPC XO-1.75 - Stabilizing suspend/resume.
Modified: cpu/arm/mmp2/dramrecal.fth cpu/arm/mmp2/rtc.fth dev/olpc/dcon/mmp2dcon.fth
Modified: cpu/arm/mmp2/dramrecal.fth ============================================================================== --- cpu/arm/mmp2/dramrecal.fth Fri Sep 23 00:42:26 2011 (r2526) +++ cpu/arm/mmp2/dramrecal.fth Fri Sep 23 06:59:53 2011 (r2527) @@ -59,6 +59,10 @@ here ddr-recal - constant /ddr-recal
label ddr-self-refresh ( r0:memctrl-va -- ) + dsb + mcr p15,0,r0,cr8,cr5,0 \ Invalidate TLB + mcr p15,0,r0,cr7,cr10,4 \ Write data synchronization barrier + mov r1, #0x1 \ Block all data requests str r1, [r0, #0x7e0] \ SDRAM_CTRL14
@@ -73,14 +77,17 @@ \ str r1, [r0, #0x770] \ SDRAM_CTRL7_SDRAM_ODT_CTRL2
\ Store registers in SRAM so CForth can see them, for debugging -\ set r2, #0xd102.0400 -\ stmia r2, {r0-r15} + set r2, #0xd102.0400 + stmia r2, {r0-r15}
\ Linux sets the register to 0x860 ldr r1, [r0, #0x1e0] \ PHY_CTRL8 bic r1,r1,#0x07700000 \ PHY_ADCM_ZPDRV: 0 PHY_ADCM_ZNDRV: 0 (Disable drivers 6:0) str r1, [r0, #0x1e0] \ PHY_CTRL8
+\ mov r1, #0x00070000 \ PHY_SYNC_EN +\ str r1, [r0, #0x110] \ MMAP_CS1 + dsb \ Data Synchronization Barrier wfi \ Wait for interrupt
@@ -295,13 +302,305 @@ \ WAKEUP6: SDH1_CD, SDH3_CD, MSP_INS \ WAKEUP7: PMIC INT 5 value sleep-depth -: setup-wakeup-sources ( -- mask ) - h# 0002.0094 h# 4c mpmu! \ RTC_ALARM, WAKEUP7, WAKEUP4, WAKEUP2 -\ h# 0002.0094 h# 104c mpmu! \ RTC_ALARM, WAKEUP7, WAKEUP4, WAKEUP2 ??? +: setup-wakeup-sources ( -- mask ) +\ h# 0002.0094 h# 4c mpmu! \ RTC_ALARM, WAKEUP7, WAKEUP4, WAKEUP2 +\ h# 0002.0094 h# 104c mpmu! \ RTC_ALARM, WAKEUP7, WAKEUP4, WAKEUP2 h# ff08.7fff ( mask ) \ Enable all wakeup ports ; : block-irqs ( -- ) 1 h# 110 +icu io! ;
+\ XXX we might need to set GPIOs 71 and 160 (ps2 clocks), and perhaps the dat lines too, +\ for non-sleep-mode control - or maybe for sleep mode control as inputs. +\ We also may need to enable falling edge detects. +: disable-int40 ( -- ) d# 40 disable-interrupt ; + +: gpio-wakeup? ( gpio# -- flag ) + h# 019800 over 5 rshift la+ l@ ( gpio# mask ) + swap h# 1f and ( mask bit# ) + 1 swap lshift and 0<> ( flag ) +; + +: icu@ ( offset -- value ) h# 28.2000 + io@ ; +: .masked ( irq# -- ) + dup /l* h# 10c + icu@ ( irq# masked ) + 1 and if ( irq# ) + ." IRQ" .d ." is masked off" cr + else ( irq# ) + drop ( ) + then ( ) +; +: .selected ( irq# -- ) + dup /l* h# 100 + icu@ ( irq# n ) + dup h# 40 and if ( irq# n ) + ." IRQ" swap .d ( n ) + ." selected INT" h# 3f and .d cr ( ) + else ( irq# n ) + 2drop ( ) + then ( ) +; +: (.pending) ( d -- ) + ." pending INTs: " ( d ) + d# 64 0 do ( d ) + over 1 and if i .d then ( d ) + d2/ ( d' ) + loop ( d ) + 2drop ( ) +; +: .pending ( irq# -- ) + dup 2* /l* h# 130 + dup icu@ swap la1+ icu@ ( irq# d ) + 2dup d0= if ( irq# d ) + 3drop ( ) + else ( irq# d ) + ." IRQ " rot .d (.pending) cr ( ) + then ( ) +; + +: bit? ( n bit# -- n flag ) 1 swap lshift over and 0<> ; +: .ifbit ( n bit# msg$ -- n ) + 2>r bit? if ( n r: msg$ ) + 2r> type space ( n ) + else ( n r: msg$ ) + 2r> 2drop ( n ) + then ( n ) +; +: .enabled-ints ( -- ) + d# 64 0 do ( ) + i /l* icu@ dup h# 70 and if ( n ) + ." INT" i .d ." -> IRQ" ( n ) + 4 " 0" .ifbit ( n ) + 5 " 1" .ifbit ( n ) + 6 " 2" .ifbit ( n ) + ." Pri " h# f and .d cr ( ) + else ( n ) + drop ( ) + then ( ) + loop ( ) +; +: .int4 ( -- ) + ." INT4 - mask " h# 168 icu@ .x + ." status " h# 150 icu@ dup .x + 0 " USB " .ifbit + 1 " PMIC" .ifbit + drop cr +; +: .int5 ( -- ) + ." INT5 - mask " h# 16c icu@ .x + ." status " h# 154 icu@ dup .x + 0 " RTC " .ifbit + 1 " RTC_Alarm" .ifbit + drop cr +; +: .int9 ( -- ) + ." INT9 - mask " h# 17c icu@ .x + ." status " h# 180 icu@ dup .x + 0 " Keypad " .ifbit + 1 " Rotary " .ifbit + 2 " Trackball" .ifbit + drop cr +; +: .int17 ( -- ) + ." INT17 - mask " h# 170 icu@ .x + ." status " h# 158 icu@ dup .x ( n ) + 7 2 do ( n ) + dup 1 and if ( n ) + ." TWSI" i .d ( n ) + then ( n ) + u2/ ( n' ) + loop ( n ) + drop cr ( ) +; +: .int35 ( -- ) + ." INT5 - mask " h# 174 icu@ .x + ." status " h# 15c icu@ dup .x + d# 0 " PJ_PerfMon" .ifbit + d# 1 " L2_PA_ECC" .ifbit + d# 2 " L2_ECC" .ifbit + d# 3 " L2_UECC" .ifbit + d# 4 " DDR" .ifbit + d# 5 " Fabric0" .ifbit + d# 6 " Fabric1" .ifbit + d# 7 " Fabric2" .ifbit + d# 9 " Thermal" .ifbit + d# 10 " MainPMU" .ifbit + d# 11 " WDT2" .ifbit + d# 12 " CoreSight" .ifbit + d# 13 " PJ_Commtx" .ifbit + d# 14 " PJ_Commrx" .ifbit + drop + cr +; +: .int51 ( -- ) + ." INT51 - mask " h# 178 icu@ .x + ." status " h# 160 icu@ dup .x + 0 " HSI_CAWAKE1 " .ifbit + 1 " MIPI_HSI1" .ifbit + drop cr +; +: .int55 ( -- ) + ." INT55 - mask " h# 184 icu@ .x + ." status " h# 188 icu@ dup .x + 0 " HSI_CAWAKE0 " .ifbit + 1 " MIPI_HSI0" .ifbit + drop cr +; + +: .fiq ( -- ) + h# 304 icu@ if ." FIQ is masked off" cr then + h# 300 icu@ dup h# 40 and if ." FIQ selected INT" h# 3f and .d cr else drop then + h# 310 icu@ h# 314 icu@ 2dup d0= if ( d ) + 2drop ( ) + else ( d ) + ." FIQ " (.pending) cr ( ) + then ( ) +; + +: .icu ( -- ) + .enabled-ints + 3 0 do i .masked i .selected i .pending loop + \ XXX should handle DMA interrupts too + .fiq + .int4 .int5 .int9 .int17 .int35 .int51 .int55 +; +string-array wakeup-bit-names + ," WU0 " + ," WU1 " + ," WU2 " + ," WU3 " + ," WU4 " + ," WU5 " + ," WU6 " + ," WU7 " + ," TIMER_1_1 " + ," TIMER_1_2 " + ," TIMER_1_3 " + ," MSP_INS " + ," AUDIO " + ," WDT1 " + ," TIMER_2_1 " + ," TIMER_2_2 " + ," TIMER_2_3 " + ," RTC_ALARM " + ," WDT2 " + ," ROTARY " + ," TRACKBALL " + ," KEYPRESS " + ," SDH3_CARD " + ," SDH1_CARD " + ," FULL_IDLE " + ," ASYNC_INT " + ," SSP1_SRDY " + ," CAWAKE " + ," resv28 " + ," SSP3_SRDY " + ," ALL_WU " + ," resv31 " +end-string-array + +string-array wakeup-mask-names + ," WU0 " + ," WU1 " + ," WU2 " + ," WU3 " + ," WU4 " + ," WU5 " + ," WU6 " + ," WU7 " + ," TIMER_1_1 " + ," TIMER_1_2 " + ," TIMER_1_3 " + ," " + ," " + ," " + ," TIMER_2_1 " + ," TIMER_2_2 " + ," TIMER_2_3 " + ," RTC_ALARM " + ," WDT2 " + ," ROTARY " + ," TRACKBALL " + ," KEYPRESS " + ," SDH3_CARD " + ," SDH1_CARD " + ," FULL_IDLE " + ," ASYNC_INT " + ," WDT1 " + ," SSP3_SRDY " + ," SSP1_SRDY " + ," CAWAKE " + ," MSP_INS " + ," resv31 " +end-string-array + +: .active-wakeups ( -- ) + ." Wakeups: " + h# 1048 mpmu@ ( n ) + d# 31 0 do ( n ) + dup 1 and if i wakeup-bit-names count type then ( n ) + u2/ ( n' ) + loop ( n ) + drop cr ( ) +; +: .wakeup-mask ( -- ) + ." Enabled wakeups: " + h# 4c mpmu@ h# 104c or ( n ) + d# 31 0 do ( n ) + dup 1 and if i wakeup-mask-names count type then ( n ) + u2/ ( n' ) + loop ( n ) + drop cr ( ) +; +: .edges ( -- ) + ." Wakeup edges: " ( ) + d# 6 0 do ( ) + h# 19800 i la+ io@ ( n ) + d# 32 0 do ( n ) + dup 1 and if ( n ) + j d# 32 * i + .d ( n ) + then ( n ) + u2/ ( n' ) + loop ( n ) + drop ( ) + loop ( ) + cr ( ) +; +: .edge-enables ( -- ) + ." Enabled edges: " + d# 160 0 do + i af@ dup h# 70 and h# 40 <> if ( n ) + dup h# 10 and if ." R" then ( n ) + dup h# 20 and if ." F" then ( n ) + dup h# 40 and if ." C" then ( n ) + i .d ( n ) + then ( n ) + drop ( ) + loop +; +: .wakeup ( -- ) .active-wakeups .wakeup-mask .edges .edge-enables ; + +: .irqstat ( -- ) h# 148 h# 130 do i icu@ . 4 +loop ; +\ !!! The problem right now is that I have woken from keyboard, but the interrupt is still asserted +\ So perhaps the interrupt handler didn't fire +: rotate-wakeup? ( -- flag ) d# 15 gpio-wakeup? ; +: kbd-wakeup? ( -- flag ) d# 71 gpio-wakeup? ; +: tpd-wakeup? ( -- flag ) d# 160 gpio-wakeup? ; +\ We need to do this in the SP interrupt handler +: clear-wakeup ( gpio# -- ) + dup af@ ( gpio# value ) + 2dup h# 40 or swap af! ( gpio# value ) + swap af! +; +\ How to wakeup from SP: +: setup-key-wakeup ( -- ) + d# 24 d# 16 do h# b1 i af! loop \ Wake SP on game keys + h# b0 d# 15 af! \ Wake SP on rotate key + h# 220 d# 71 af! \ Wake SP on KBD CLK falling edge + h# 221 d# 160 af! \ Wake SP on TPD CLK falling edge + h# 4c mpmu@ h# 20.0000 or h# 4c mpmu! \ Keypress wakes SP + ['] disable-int40 d# 40 interrupt-handler! + d# 40 enable-interrupt \ SP to PJ4 communications interrupt + h# 2900cc io@ 1 invert and h# 2900cc io! \ Unmask the communications interrupt +; + 0 value save-apcr 0 value save-idlecfg
@@ -404,6 +703,8 @@ " dcon-suspend" $call-screen then " suspend" $call-screen + " set-ack" $call-ec + \ 0 h# 54 pmua! \ Kill the SDIO 0 clocks - insignificant savings \ 0 h# 58 pmua! \ Kill the SDIO 1 clocks - insignificant savings sleep-mask 2 and 0= if keyboard-power-off then \ Should save about 17 mW @@ -412,6 +713,7 @@ : screen-on ( -- ) sleep-mask 4 and 0= if wlan-power-on then sleep-mask 2 and 0= if keyboard-power-on then + " clr-ack" $call-ec " resume" $call-screen sleep-mask 1 and if \ DCON power up dcon-unfreeze
Modified: cpu/arm/mmp2/rtc.fth ============================================================================== --- cpu/arm/mmp2/rtc.fth Fri Sep 23 00:42:26 2011 (r2526) +++ cpu/arm/mmp2/rtc.fth Fri Sep 23 06:59:53 2011 (r2527) @@ -15,10 +15,13 @@ ; : soc-rtc@ ( offset -- value ) h# 01.0000 + io@ ; : soc-rtc! ( value offset -- value ) h# 01.0000 + io! ; +: cancel-alarm ( -- ) + 0 8 soc-rtc! + int5-mask@ 1 or int5-mask! \ Mask alarm +; : take-alarm ( -- ) ." Alarm fired" cr - 0 8 soc-rtc! - int5-mask@ 1 or int5-mask! \ Mask alarm + cancel-alarm ; : alarm-in-3 ( -- ) enable-rtc \ Turn on clocks @@ -30,3 +33,79 @@ ['] take-alarm 5 interrupt-handler! 5 enable-interrupt ; +: alarm-in-1 ( -- ) + enable-rtc \ Turn on clocks + + int5-mask@ 1 invert and int5-mask! \ Unmask alarm + enable-rtc-wakeup + 0 soc-rtc@ d# 1 + 4 soc-rtc! \ Set alarm for 3 seconds from now + 7 8 soc-rtc! \ Ack old interrupts and enable new ones + ['] cancel-alarm 5 interrupt-handler! + 5 enable-interrupt +; +: wake1 ( -- ) + enable-rtc \ Turn on clocks + + int5-mask@ 1 invert and int5-mask! \ Unmask alarm + enable-rtc-wakeup + 0 soc-rtc@ d# 1 + 4 soc-rtc! \ Set alarm for 3 seconds from now + 7 8 soc-rtc! \ Ack old interrupts and enable new ones + ['] cancel-alarm 5 interrupt-handler! + 5 enable-interrupt +; +: alarm1 ( -- ) + enable-rtc \ Turn on clocks + + int5-mask@ 1 invert and int5-mask! \ Unmask alarm + enable-rtc-wakeup + 0 soc-rtc@ d# 1 + 4 soc-rtc! \ Set alarm for 3 seconds from now + 7 8 soc-rtc! \ Ack old interrupts and enable new ones + ['] take-alarm 5 interrupt-handler! + 5 enable-interrupt +; +: test1 + 0 + begin + alarm1 + str + (cr dup . 1+ + d# 500 ms + key? until +; +: test2 + 0 + begin + wake1 + str + (cr dup . 1+ + d# 500 ms + key? until +; +: test3 + 0 + begin + wake1 + str + cr dup . 1+ + d# 500 ms + key? until +; +: test4 + begin + 0 d# 13 at-xy + 5 0 do + wake1 str + cr i . + d# 500 ms + key? if unloop exit then + loop + again +; + +\ test3 +\ wake1 str cr + +\ patch noop cr take-alarm test1 +\ patch (cr cr take-alarm test1 + +\ : cx cr d# 400 ms ; patch cx cr take-alarm test1
Modified: dev/olpc/dcon/mmp2dcon.fth ============================================================================== --- dev/olpc/dcon/mmp2dcon.fth Fri Sep 23 00:42:26 2011 (r2526) +++ dev/olpc/dcon/mmp2dcon.fth Fri Sep 23 06:59:53 2011 (r2527) @@ -176,8 +176,8 @@ h# dc02 = ;
-: dcon-setup ( -- ) - 0 dcon@ drop 0 dcon@ drop +: dcon-setup ( -- error? ) + dcon2? 0= if ." Can't init DCON" true exit then
[ifdef] notdef d# 1200 2 dcon! \ HResolution @@ -196,9 +196,10 @@ h# 0101 h# 42 dcon!
h# 12 mode! + false ; : dcon-enable ( -- ) - dcon-setup + dcon-setup if exit then true set-color h# f bright! ; @@ -234,8 +235,12 @@ dcon-power-off ; : dcon-resume ( -- ) - dcon-power-on d# 50 ms - dcon-setup + ['] dcon-power-on catch if + ." dcon-power-on failed" cr + exit + then + d# 80 ms + dcon-setup if exit then saved-dcon-mode mode! saved-brightness bright! ;
openfirmware@openfirmware.info
-
repository service