Author: wmb Date: Fri Sep 2 09:02:34 2011 New Revision: 2496 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2496
Log: OLPC XO-1.75 - checkpoint current state of low-power test code.
Modified: cpu/arm/assem.fth cpu/arm/mmp2/dramrecal.fth cpu/arm/olpc/1.75/addrs.fth
Modified: cpu/arm/assem.fth ============================================================================== --- cpu/arm/assem.fth Wed Aug 31 10:31:46 2011 (r2495) +++ cpu/arm/assem.fth Fri Sep 2 09:02:34 2011 (r2496) @@ -1401,7 +1401,7 @@ : sev ( -- ) 0320f004 {cond} op( )op ;
: nop ( -- ) e1a00000 {} op( )op ; \ mov r0,r0 -: dsb ( -- ) f57ff040 {} op( )op ; \ "dsb sy" is f57ff04f +: dsb ( -- ) f57ff04f {} op( )op ; \ "dsb" is equivalent to "dsb sy" - f57ff04f : dmb ( -- ) f57ff050 {} op( )op ; : isb ( -- ) f57ff060 {} op( )op ;
Modified: cpu/arm/mmp2/dramrecal.fth ============================================================================== --- cpu/arm/mmp2/dramrecal.fth Wed Aug 31 10:31:46 2011 (r2495) +++ cpu/arm/mmp2/dramrecal.fth Fri Sep 2 09:02:34 2011 (r2496) @@ -72,25 +72,22 @@ \ orr r1, r1, #0x000a \ ODT{1,0}_SWITCH_MODE: Termination controlled by Read and Write enables \ str r1, [r0, #0x770] \ SDRAM_CTRL7_SDRAM_ODT_CTRL2
-[ifdef] notdef +\ Store registers in SRAM so CForth can see them, for debugging +\ set r2, #0xd102.0400 +\ stmia r2, {r0-r15} + + \ Linux sets the register to 0x860 ldr r1, [r0, #0x1e0] \ PHY_CTRL8 bic r1,r1,#0x07700000 \ PHY_ADCM_ZPDRV: 0 PHY_ADCM_ZNDRV: 0 (Disable drivers 6:0) str r1, [r0, #0x1e0] \ PHY_CTRL8 -[then]
- set r2, #0xfe086000 - set r3, #0xfe050000 - str r2, [r3] \ Final write to SP votes - - mcr p15,0,r0,7,10,4 \ Data Synchronization Barrier -\ dsb \ Data Synchronization Barrier + dsb \ Data Synchronization Barrier wfi \ Wait for interrupt
-[ifdef] notdef + \ Linux sets the register to 0x07700860, hardcoding the drive strength ldr r1, [r0, #0x1e0] \ PHY_CTRL8 orr r1,r1,#0x07700000 \ PHY_ADCM_ZPDRV: 7 PHY_ADCM_ZNDRV: 7 (Enable drivers 6:0) str r1, [r0, #0x1e0] \ PHY_CTRL8 -[then]
\ This block was commented-out in the Linux code, and the value is incorrect for OLPC in any case \ mov r1, #0x02000000 \ PAD_TERM_SWITCH_MODE: Termination enabled during all reads @@ -100,11 +97,11 @@ mov r1, #0x80000000 \ PHY_SYNC_EN str r1, [r0, #0x240] \ PHY_CTRL14
- ldr r1, [r0, #230] \ PHY_CTRL13 + ldr r1, [r0, #0x230] \ PHY_CTRL13 orr r1,r1,#0xf0000000 \ DLL_RESET_TIMER: 15*256 memory clocks \ mov r1, #0xf0000000 \ DLL_RESET_TIMER: 15*256 memory clocks \ orr r1, r1, #0x0040 \ DLL_PHSEL: 4 (45 + 4*3 = 57 degrees) - adjust? - str r1, [r0, #230] \ PHY_CTRL13 + str r1, [r0, #0x230] \ PHY_CTRL13
mov r1, #0x20000000 \ PHY_DLL_RESET str r1, [r0, #0x240] \ PHY_CTRL14 @@ -168,8 +165,11 @@ code do-self-refresh ( -- ) set r0,`memctrl-va #` \ Memory controller virtual address set r1,`'ddr-self-refresh #` \ Address of ddr-self-refresh routine in SRAM + mov r7,sp + set sp,`'ddr-self-refresh-sp #` mov lr,pc mov pc,r1 + mov sp,r7 c;
: +apbc ( offset -- io-offset ) h# 01.5000 + ; @@ -217,16 +217,28 @@ h# f0 h# 1c +scu io-clr \ SCU_MCB_CONF ; : disable-apmu-clks ( -- ) - h# 3f h# d8 +apmu io-clr \ PMUA_MSPRO_CLK_RES_CTRL - h# 1fffd h# dc +apmu io-clr \ PMUA_GLB_CLK_RES_CTRL -\ 0 h# 68 +apmu io! \ PMUA_WTM_CLK_RES_CTRL - h# 9 h# 5c +apmu io-clr \ PMUA_USB_CLK_RES_CTRL + h# 1b h# 54 +apmu io-clr \ PMUA_SDH0_CLK_RES_CTRL + h# 1b h# 58 +apmu io-clr \ PMUA_SDH1_CLK_RES_CTRL + h# 1b h# e8 +apmu io-clr \ PMUA_SDH2_CLK_RES_CTRL + h# 1b h# d4 +apmu io-clr \ PMUA_SMC_CLK_RES_CTRL + h# 3f h# 60 +apmu io-clr \ PMUA_NF_CLK_RES_CTRL + h# 3f h# d8 +apmu io-clr \ PMUA_MSPRO_CLK_RES_CTRL - XO does not use MSPRO + h# 12 h# 10c +apmu io-clr \ PMUA_AUDIO_CLK_RES_CTRL + h# 1fffd h# dc +apmu io-clr \ PMUA_GLB_CLK_RES_CTRL +\ 0 h# 68 +apmu io! \ PMUA_WTM_CLK_RES_CTRL + h# 9 h# 5c +apmu io-clr \ PMUA_USB_CLK_RES_CTRL ; : enable-apmu-clks ( -- ) - h# 3f h# d8 +apmu io-set \ PMUA_MSPRO_CLK_RES_CTRL - h# 1fffd h# dc +apmu io-set \ PMUA_GLB_CLK_RES_CTRL -\ h# 1b h# 68 +apmu io! \ PMUA_WTM_CLK_RES_CTRL - h# 9 h# 5c +apmu io-set \ PMUA_USB_CLK_RES_CTRL + h# 1b h# 54 +apmu io-set \ PMUA_SDH0_CLK_RES_CTRL + h# 1b h# 58 +apmu io-set \ PMUA_SDH1_CLK_RES_CTRL + h# 1b h# e8 +apmu io-set \ PMUA_SDH2_CLK_RES_CTRL + h# 1b h# d4 +apmu io-set \ PMUA_SMC_CLK_RES_CTRL \ ??? what is this and why is it on? + h# 3f h# 60 +apmu io-set \ PMUA_NF_CLK_RES_CTRL \ Should this be on? +\ h# 3f h# d8 +apmu io-set \ PMUA_MSPRO_CLK_RES_CTRL + h# 12 h# 10c +apmu io-set \ PMUA_AUDIO_CLK_RES_CTRL + h# 1fffd h# dc +apmu io-set \ PMUA_GLB_CLK_RES_CTRL +\ h# 1b h# 68 +apmu io! \ PMUA_WTM_CLK_RES_CTRL + h# 9 h# 5c +apmu io-set \ PMUA_USB_CLK_RES_CTRL ; : disable-mpmu-clks ( -- ) h# a010 h# 1024 +mpmu io! \ MPMU_ACGR @@ -310,9 +322,37 @@ save-apcr h# 1000 +mpmu io! ( ) \ Restore APCR save-idlecfg h# 18 +apmu io! ( ) \ Restore IDLE_CFG ; +\ Questions: +\ Meaning of various connect type options +\ do LP mode settings take effect immediately if SP is already at WFI, or only on entry to WFI +\ does WFI make any difference on SP? I don't see any difference in power +\ Which WFI instruction on SP? +\ Which WFI instruction on PJ4? +\ Any undocumented bits that affect the situation? +\ What are the _INT versions of the XDB config files? +\ What does CS stand for in ARM/CS ? +\ When using XDB on XO with OFW, XDB can see entry to LP state - core Status stays running - LowPower Internal +\ How to recapture short of restarting XDB? +\ Pushing button on JTAG box often seems to have no effect + : setup-sleep-state ( -- ) \ begin mmp2_pm_enter_lowpower_mode(state)
+ \ Security processor setup + sleep-depth 4 >= if \ state at least POWER_MODE_CHIP_SLEEP (turn off most of SoC) + h# fe08.6000 0 +mpmu io! \ In SP, set AXISD, resvd, SLPEN, SPSD, DDRCORSD, APBSD resvd, VCXOSD + then + + sleep-depth 3 = if \ state at least POWER_MODE_APPS_SLEEP (turn off slow IO) + h# de00.6000 0 +mpmu io! \ In SP, set AXISD, resvd, SPSD, DDRCORSD, APBSD resvd, + then + +\ Linux value +\ h# 8030.0020 h# 14 +apmu io! \ IN PMUA_SP_IDLE_CFG, set , DIVIDER_RESET_EN, SP_DIS_MC_SW_REQ, SP_MC_WAKE_EN, TCM_STATE_RETAIN + h# 8020.0020 h# 14 +apmu io! \ IN PMUA_SP_IDLE_CFG, set , DIVIDER_RESET_EN, SP_DIS_MC_SW_REQ, TCM_STATE_RETAIN + + \ PJ4 setup + h# 1000 +mpmu io@ to save-apcr h# 18 +apmu io@ to save-idlecfg
@@ -323,28 +363,23 @@ h# 0008.0000 or ( apcr' ) \ Set VCXOSD then
- h# 2000.0000 0 +mpmu io-clr \ In SP, clear SLPEN - we might set it later - sleep-depth 4 >= if \ state at least POWER_MODE_CHIP_SLEEP (turn off most of SoC) - h# 2008.0000 0 +mpmu io-set \ In SP, also set SLPEN, VCXOSD h# 2000.0000 or ( apcr' ) \ Set SLPEN setup-wakeup-sources and ( apcr' ) then
sleep-depth 3 >= if \ state at least POWER_MODE_APPS_SLEEP (turn off slow IO) - h# de00.0000 0 +mpmu io-set \ In SP, set AXISD, resvd, SPSD, DDRCORSD, APBSD resvd, h# 0400.0000 or ( apcr' ) \ Set APBSD then
- h# 8030.0020 h# 14 +apmu io! ( apcr ) \ IN PMUA_SP_IDLE_CFG, set , DIVIDER_RESET_EN, SP_DIS_MC_SW_REQ, SP_MC_WAKE_EN, TCM_STATE_RETAIN - sleep-depth 2 >= if \ state at least POWER_MODE_APPS_IDLE (turn off fast IO and DDR) h# 8800.0000 or ( apcr' ) \ Set AXISD, DDRCORSD then
h# 5200.0000 or ( apcr' ) \ Set DSPSD (bit 30, reserved), SPSD (bit 28), BBSD (bit 25, resvd)
- save-idlecfg 1 invert and ( apcr idle ) \ PMUA_MOH_IDLE + save-idlecfg 2 invert and ( apcr idle ) \ Clear PMUA_MOH_IDLE (AKA PJ_IDLE) +\ h# 8000.0000 invert and ( apcr idle' ) \ Clear PJ_DBG_CLOCK_EN
sleep-depth 2 >= if \ state at least POWER_MODE_APPS_IDLE h# 0000.0020 or ( apcr idle' ) \ PJ_PWRDWN @@ -352,7 +387,7 @@
sleep-depth 1 >= if \ state at least POWER_MODE_CORE_EXTIDLE h# 3000.0000 invert and ( apcr idle' ) \ PJ_ISO_MODE_CNTRL - isolation controlled by processor logic and active - h# 000a.0000 or ( apcr idle' ) \ 2 L2 power switches, 1 L1 power switch, 3 core power switches + h# 000a.0002 or ( apcr idle' ) \ 2 L2 power switches, 1 L1 power switch, 3 core power switches then
h# 0020.0000 or ( apcr idle' ) \ PJ_DIS_MC_SW_REQ - disable idle entry using software register bits @@ -376,7 +411,16 @@ : stdin-idle-on ['] safe-idle to stdin-idle d# 15 enable-interrupt ; : stdin-idle-off ['] noop to stdin-idle install-uart-io d# 15 disable-interrupt ;
+: timers-off ( -- ) + 0 h# 14048 io! \ Disable interrupts from the tick timer + 7 h# 1407c io! \ Clear any pending interrupts + h# f disable-interrupt \ Block timer interrupt +; + : str ( -- ) + timers-off + + screen-dark stdin-idle-off 5 h# 38 +mpmu io! \ Use 32 kHz clock instead of VCXO for slow clock
@@ -391,7 +435,7 @@
setup-sleep-state
-\ h# 00c0.0000 h# 8c +apmu io-set \ Power down CoreSight SRAM + h# 000c.0000 h# 8c +apmu io-set \ Power down CoreSight SRAM
\ TODO - need to power down sram/l2$ \ mmp2_cpu_disable_l2(0); @@ -402,7 +446,7 @@ disable-clks
\ begin mmp2_cpu_do_idle() - block-irqs ( ) \ Block IRQs - will be cleared by PMU + block-irqs ( ) \ Block IRQs - will be cleared by PMU do-self-refresh ( )
restore-run-state
Modified: cpu/arm/olpc/1.75/addrs.fth ============================================================================== --- cpu/arm/olpc/1.75/addrs.fth Wed Aug 31 10:31:46 2011 (r2495) +++ cpu/arm/olpc/1.75/addrs.fth Fri Sep 2 09:02:34 2011 (r2496) @@ -71,5 +71,6 @@
sram-va h# 2.0000 + constant 'ddr-recal sram-va h# 2.0100 + constant 'ddr-self-refresh +sram-va h# 2.0400 + constant 'ddr-self-refresh-sp
sram-pa h# 2.4000 + constant diagfb-pa \ Low-resolution frame buffer for startup numbers
openfirmware@openfirmware.info
-
repository service