openfirmware

openfirmware@openfirmware.info

3007 discussions

Re: [openfirmware] Making Open Firmware look like CE
by Mark Morgan Lloyd 31 May '11

31 May '11

Mitch Bradley wrote: > The NK.bin file makes sense in light of the .bin format description and tool that I posted in my last message. > > The first few segment records: > > a) (offset 0x0f) Insert a branch instruction (0xea0003fe) at location 0x80100000 > > b) (offset 0x1f) Insert a CECE + pointer block at location 0x80100040. The pointer value is 0x81c61460. It is a pointer to a "romhdr" structure as described at http://msdn.microsoft.com/en-us/library/aa908726.aspx > > c) (offset 0x33) Insert a TOC pointer at location 0x80100048. TOC is "Table of Contents", which is a data structure that WinCE uses when it is starting up. It helps WinCE find various parts of itself. The TOC pointer value is 0x01b61460. > > d) (offset 0x43) Copy the kernel image (of size 0x0004292c) to location 0x80101000. The data in that section is clearly a bunch of ARM instructions. ARM opcodes have a very high probability of having an "e" in the high nibble (which means the instruction is not conditional). > > The rest of the file is almost certainly a bunch of sections for copying various DLLs into memory. > > "XIP" just means that the code has been prelinked and the addresses have been resolved to the absolute address at which the code is expected to execute, so relocation information is unnecessary and not present. > > Here is what you should do: > > 1) Try the makecebin.fth program. Use it to wrap an OFW image file - or any other file for that matter - into a .bin format file. Then see if BLDR will try to load that file. If BLDR will load it, then we have solved the file format problem and it is then a matter of modifying OFW to work on your board in that environment. > > 2) If BLDR will not load it, we then need to work out what needs to be added. The first thing to try would be to add an ECEC section. It might be sufficient to have the ECEC section refer to a dummy address. I doubt that the bootloader actually follows the ECEC pointer, because that would require sophisticated parsing of the .bin section information to find data that is much later in the file. Instead, what I think happens is that the bootloader just uses the section information to place stuff in memory, and then the WinCE kernel/BSP code follows the pointer. But it is possible that the bootloader might do a quick check to see if an ECEC section exists. We shouldn't worry about this step (2) until we are sure that it is necessary. Thanks Mitch, I'll investigate. I'll be back, but possibly not immediately due to other commitments. -- Mark Morgan Lloyd markMLl .AT. telemetry.co .DOT. uk [Opinions above are the author's, not those of his employers or colleagues]

1 0

[commit] r2234 - cpu/arm/olpc/1.75
by repository service 31 May '11

31 May '11

Author: wmb Date: Tue May 31 01:23:49 2011 New Revision: 2234 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2234 Log: OLPC XO-1.75 - fixed microphone test. It turns out that the ALC5631 codec doesn't like to have its ADC powered up before BCLK is present. Modified: cpu/arm/olpc/1.75/alc5631.fth cpu/arm/olpc/1.75/sound.fth Modified: cpu/arm/olpc/1.75/alc5631.fth ============================================================================== --- cpu/arm/olpc/1.75/alc5631.fth Fri May 27 04:16:25 2011 (r2233) +++ cpu/arm/olpc/1.75/alc5631.fth Tue May 31 01:23:49 2011 (r2234) @@ -1,17 +1,36 @@ \ See license at end of file purpose: Driver for Realtek ALC5631Q audio CODEC chip +: adc-on ( -- ) h# 0c00 h# 3a codec-set ; +: adc-off ( -- ) h# 0c00 h# 3a codec-clr ; +: dac-on ( -- ) h# 0300 h# 3a codec-set ; +: dac-off ( -- ) h# 0300 h# 3a codec-clr ; + : codec-on ( -- ) - h# 8001 h# 34 codec! \ Slave mode, 16 bits, left justified - b# 1001.1111.1110.0000 h# 3a codec! \ All on - b# 1111.1100.0011.1100 h# 3b codec! \ All on except PLL + 0 0 codec! \ Reset + b# 1010.0000.0001.1101 h# 3c codec! \ All on except AX and MONO + d# 110 ms + b# 1110.0000.0001.1101 h# 3c codec! \ Fast VREF control + d# 100 ms + + h# 8021 h# 34 codec! \ Slave mode, 16 bits, left justified, left channel on LRCLK high + + h# 1010 h# 38 codec! \ Divisors; the values in this register don't seem to make much + \ difference unless you set the divisors to very high values. + + \ The ADC and DAC will be turned on as needed by adc-on and dac-on, after + \ the BCLK clock from the SoC is on. If you turn on the ADC when BCLK is + \ not clocking, the ADC often doesn't output any data. + b# 1001.0000.1110.0000 h# 3a codec! \ All on except ADC and DAC + b# 1111.1100.0011.1100 h# 3b codec! \ All on except PLL b# 1111.1100.0000.0000 h# 3e codec! \ AXI and MONO IN off + \ h# 8c00 h# 40 codec! \ Speaker Amp Auto Ratio GAIN, use HPFs - h# 8000 h# 40 codec! \ Speaker Amp Auto Ratio GAIN, no HPFs + h# 4e00 h# 40 codec! \ Speaker Amp Ratio GAIN is 1.44x, no HPFs h# 0000 h# 42 codec! \ Use MCLK, not PLL - b# 1110.1100.1001.0000 h# 52 codec! \ Protection on - h# 4000 h# 56 codec! \ Power on Cap-free block with de-pop +\ b# 1110.1100.1001.0000 h# 52 codec! \ Protection on + h# 8000 h# 56 codec! \ HP depop by register control ; : codec-off ( -- ) 0 h# 3a codec! \ All off @@ -82,7 +101,7 @@ ; d# 0 constant default-adc-gain \ 0 dB - range is -96.625 to +28.5 d# 0 constant default-dac-gain \ 0 dB - range is -96.625 to +28.5 -d# 44 constant default-mic-gain \ 44 dB - range is 0 to 50 dB +d# 52 constant default-mic-gain \ 52 dB - range is 0 to 52 dB d# 0 constant default-speaker-volume \ 0 dB - range is -46.5 to +12 d# -10 constant default-headphone-volume \ -10 dB - range is -46.5 to 0 @@ -131,6 +150,7 @@ false value external-mic? : mic-routing ( -- n ) mic1-single-ended mic2-single-ended + mic1-low-bias mic2-low-bias \ Works better than high bias adc-unmute-mic ; : db>mic-boost ( db -- code ) @@ -172,7 +192,9 @@ d# 48000 of h# 0000 h# 3072 endof ( default ) true abort" Unsupported audio sample rate" endcase ( reg62val2 reg60val ) - h# 60 codec! h# 62 codec! + \ XXX need to do something with register 38 + 2drop +\ h# 60 codec! h# 62 codec! ; \ LICENSE_BEGIN Modified: cpu/arm/olpc/1.75/sound.fth ============================================================================== --- cpu/arm/olpc/1.75/sound.fth Fri May 27 04:16:25 2011 (r2233) +++ cpu/arm/olpc/1.75/sound.fth Tue May 31 01:23:49 2011 (r2234) @@ -193,6 +193,15 @@ r> codec! ( ) ; +[ifdef] cl2-a1 +fload ${BP}/cpu/arm/olpc/1.75/alc5624.fth \ Realtek ALC5624 CODEC +[else] +: headphones-inserted? ( -- flag ) d# 97 gpio-pin@ ; +: microphone-inserted? ( -- flag ) d# 96 gpio-pin@ ; + +fload ${BP}/cpu/arm/olpc/1.75/alc5631.fth \ Realtek ALC5631Q CODEC +[then] + d# 48000 value sample-rate \ Longest time to wait for a buffer event - a little more @@ -284,6 +293,7 @@ copy-out start-out-ring enable-sspa-tx + dac-on out-len if copy-out then \ Prefill the second buffer install-playback-alarm true to playing? @@ -323,6 +333,7 @@ tuck to in-len to in-adr ( actual ) make-in-ring ( actual ) enable-sspa-rx ( actual ) + adc-on ( actual ) start-in-ring ( actual ) begin in-len while ( actual ) wait-in ( actual ) @@ -351,15 +362,6 @@ \ Page 1498 - The data transmit register is listed as RO. How can a transmit register be RO???? [then] -[ifdef] cl2-a1 -fload ${BP}/cpu/arm/olpc/1.75/alc5624.fth \ Realtek ALC5624 CODEC -[else] -: headphones-inserted? ( -- flag ) d# 97 gpio-pin@ ; -: microphone-inserted? ( -- flag ) d# 96 gpio-pin@ ; - -fload ${BP}/cpu/arm/olpc/1.75/alc5631.fth \ Realtek ALC5631Q CODEC -[then] - : set-sample-rate ( rate -- ) dup to sample-rate dup set-ctlr-sample-rate

1 0

Making Open Firmware look like CE
by Mark Morgan Lloyd 30 May '11

30 May '11

A few weeks ago (mid March) I mentioned that I had some ARM boards that I'd like use as Linux development systems. Unfortunately, they come with CE, and while the manufacturer does supply Linux it's prohibitively expensive. CE is booted from a partitioned CompactFlash card, and I initially thought that the code in the partition and filesystem boot sectors was relevant, i.e. that there was something equivalent to a PC's BIOS in Flash. However on inspection I think that the code is x86, which implies that the loader in Flash is reading and transferring control to the OS image directly. Is it possible to build Open Firmware to look like a CE image, which would possibly allow this board (and potentially many other devices) to run Linux without modification to the content of internal Flash? -- Mark Morgan Lloyd markMLl .AT. telemetry.co .DOT. uk [Opinions above are the author's, not those of his employers or colleagues]

2 5

How to play a music with tone?
by 胡松涛 30 May '11

30 May '11

Hi everyone, I want to make a small demo for Open Firmware to show that it can play a music. the very basic is : play, pause, play with play, I use tone . but, I can't find WORD for pause, where is it? further more, I read some articles about midi file. It's a little complicated for me. So I want to finished the first tone-music first :) PS: Are there some detail articles about Open Firmware handle with music? wav, midi, mp3 or event avi? -- Hu Songtao works as an English Teacher in weekends Skype: idisblueflash Beijing, China

2 1

[commit] r2233 - cpu/arm/olpc/1.75 dev/usb2 dev/usb2/device/hub dev/usb2/hcd dev/usb2/hcd/ehci
by repository service 27 May '11

27 May '11

Author: wmb Date: Fri May 27 04:16:25 2011 New Revision: 2233 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2233 Log: OLPC trac #10887 - added selftest support for USB hubs. Modified: cpu/arm/olpc/1.75/usb.fth dev/usb2/device/hub/hub.fth dev/usb2/hcd/ehci/probe.fth dev/usb2/hcd/ehci/qhtd.fth dev/usb2/hcd/hcd-call.fth dev/usb2/hcd/probehub.fth dev/usb2/pkt-data.fth Modified: cpu/arm/olpc/1.75/usb.fth ============================================================================== --- cpu/arm/olpc/1.75/usb.fth Thu May 26 23:23:22 2011 (r2232) +++ cpu/arm/olpc/1.75/usb.fth Fri May 27 04:16:25 2011 (r2233) @@ -16,6 +16,9 @@ : otg-set-host-mode 3 h# a8 ehci-reg! ; \ Force host mode ' otg-set-host-mode to set-host-mode + \ Port 1 on the hub (bit 0) is connected to unused pins on the + \ WLAN connector, so testing it is confusing + h# e " hub-port-mask" integer-property end-package d# 300 config-int usb-delay \ Milliseconds to wait before probing hub ports Modified: dev/usb2/device/hub/hub.fth ============================================================================== --- dev/usb2/device/hub/hub.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/device/hub/hub.fth Fri May 27 04:16:25 2011 (r2233) @@ -53,6 +53,11 @@ reprobe-hub-xt execute then ; +: selftest ( -- ) + ['] hub-id catch 0= if + hub-selftest-xt execute + then +; probe-hub Modified: dev/usb2/hcd/ehci/probe.fth ============================================================================== --- dev/usb2/hcd/ehci/probe.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/hcd/ehci/probe.fth Fri May 27 04:16:25 2011 (r2233) @@ -60,9 +60,10 @@ then ( #testable-ports ) ; +: port-connected? ( port# -- flag ) portsc@ h# 2001 and ; : wait-connect ( port# -- error? ) begin ( port# ) - dup portsc@ h# 2001 and 0= ( port# unconnected? ) + dup port-connected? 0= ( port# unconnected? ) while ( port# ) key? if ( port# ) key h# 1b = if ( port# ) \ ESC aborts @@ -156,11 +157,11 @@ ehci-reg dup 0= if map-regs then #testable-ports 0 ?do - i portsc@ h# 2001 and if \ Port owned by usb 1.1 controller (2000) or device is present (1) + i port-connected? if \ Port owned by usb 1.1 controller (2000) or device is present (1) ." USB 2.0 port " i u. ." in use" cr else diagnostic-mode? if - ." Please connect a device to USB port " i u. " !" cr + ." Please connect a device to USB port " i u. cr i wait-connect if true unloop exit then else ." Fisheye pattern out to USB 2.0 port " i u. cr Modified: dev/usb2/hcd/ehci/qhtd.fth ============================================================================== --- dev/usb2/hcd/ehci/qhtd.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/hcd/ehci/qhtd.fth Fri May 27 04:16:25 2011 (r2233) @@ -549,7 +549,7 @@ ; true value delay? -: poll-delay ( -- ) d# 100 " us" evaluate ; +: poll-delay ( -- ) d# 300 " us" evaluate ; : done? ( qh -- usberr ) delay? if poll-delay then begin dup qh-done? 0= while ( qh ) Modified: dev/usb2/hcd/hcd-call.fth ============================================================================== --- dev/usb2/hcd/hcd-call.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/hcd/hcd-call.fth Fri May 27 04:16:25 2011 (r2233) @@ -13,12 +13,15 @@ \ Probing support : set-target ( device -- ) " set-target" $call-parent - ; +; : probe-hub-xt ( -- adr ) - " probe-hub-xt" $call-parent + " probe-hub-xt" $call-parent ; : reprobe-hub-xt ( -- adr ) - " reprobe-hub-xt" $call-parent + " reprobe-hub-xt" $call-parent +; +: hub-selftest-xt ( -- adr ) + " hub-selftest-xt" $call-parent ; : set-pipe-maxpayload ( size len -- ) " set-pipe-maxpayload" $call-parent Modified: dev/usb2/hcd/probehub.fth ============================================================================== --- dev/usb2/hcd/probehub.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/hcd/probehub.fth Fri May 27 04:16:25 2011 (r2233) @@ -11,6 +11,9 @@ : power-hub-port ( port -- ) PORT_POWER DR_PORT " set-feature" $call-parent drop ; : reset-hub-port ( port -- ) PORT_RESET DR_PORT " set-feature" $call-parent drop d# 20 ms ; +\ Test modes: 1:J 2:K 3:SE0_NAK 4:Packet 5:ForceEnable +: test-hub-port ( port test-mode -- ) wljoin PORT_TEST DR_PORT " set-feature" $call-parent drop ; +: untest-hub-port ( port -- ) PORT_TEST DR_PORT " clear-feature" $call-parent drop ; : clear-status-change ( port -- ) C_PORT_CONNECTION DR_PORT " clear-feature" $call-parent drop ; : parent-set-target ( dev -- ) " set-target" $call-parent ; : hub-error? ( -- error? ) @@ -155,6 +158,77 @@ : reprobe-hub-xt ( -- adr ) ['] do-reprobe-hub ; +: hub-port-connected? ( port# -- flag ) + get-port-status if false exit then + hub-buf c@ 1 and 0<> +; +0 value hub-dev +: wait-hub-connect ( port# -- error? ) + begin ( port# ) + dup hub-port-connected? 0= ( port# unconnected? ) + while ( port# ) + key? if ( port# ) + key h# 1b = if ( port# ) \ ESC aborts + drop true exit ( -- true ) + then ( port# ) + then ( port# ) + repeat ( port# ) + ." Device connected - probing ... " + probe-setup ( port# ) + hub-dev swap ['] probe-hub-port catch if ( x x ) + 2drop ( ) + ." Failed" cr ( ) + true ( true ) + else ( ) + ." Done" cr ( ) + false ( false ) + then ( error? ) + probe-teardown ( error? ) +; + +0 value hub-test-mask +: hub-selftest ( hub-dev -- error? ) + to hub-dev ( ) + + " hub-port-mask" get-inherited-property if ( ) + -1 ( mask ) + else ( propval$ ) + get-encoded-int ( mask ) + then ( mask ) + to hub-test-mask ( ) + + hub-#ports 1+ 1 ?do ( ) + 1 i 1- lshift hub-test-mask and if + hub-dev parent-set-target ( ) + i get-port-status if ( ) + ." Get-port-status failed for hub port " i u. cr + true unloop exit ( -- true ) + then ( ) + hub-buf c@ 8 and if \ Connected ( ) + ." Hub port " i u. ." in over current" cr + true unloop exit ( -- true ) + then ( ) + hub-buf c@ 1 and if \ Connected ( ) + ." Hub port " i u. ." in use" cr ( ) + else ( ) + diagnostic-mode? if ( ) + ." Please connect a device to USB hub port " i u. cr ( ) + i wait-hub-connect if true unloop exit then ( ) + else ( ) + ." Fisheye pattern out to USB hub port " i u. cr ( ) + i 4 test-hub-port ( ) + d# 2,000 ms ( ) + i untest-hub-port ( ) + i reset-hub-port i power-hub-port ( ) + then ( ) + then ( ) + then ( ) + loop ( ) + \ Mabye need to reset the entire hub here + false ( false ) +; +: hub-selftest-xt ( -- xt ) ['] hub-selftest ; + headers \ LICENSE_BEGIN Modified: dev/usb2/pkt-data.fth ============================================================================== --- dev/usb2/pkt-data.fth Thu May 26 23:23:22 2011 (r2232) +++ dev/usb2/pkt-data.fth Fri May 27 04:16:25 2011 (r2233) @@ -72,11 +72,13 @@ 04 constant PORT_RESET 08 constant PORT_POWER 09 constant PORT_LOW_SPEED -10 constant C_PORT_CONNECTION -11 constant C_PORT_ENABLE -12 constant C_PORT_SUSPEND -13 constant C_PORT_OVER_CURRENT -14 constant C_PORT_RESET +d# 16 constant C_PORT_CONNECTION +d# 17 constant C_PORT_ENABLE +d# 18 constant C_PORT_SUSPEND +d# 19 constant C_PORT_OVER_CURRENT +d# 20 constant C_PORT_RESET +d# 21 constant PORT_TEST +d# 22 constant PORT_INDICATOR \ Use tmp-l to make sure that le-l! and le-w! are atomic writes

1 0

[commit] r2232 - cpu/x86/pc/biosload
by repository service 26 May '11

26 May '11

Author: wmb Date: Thu May 26 23:23:22 2011 New Revision: 2232 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2232 Log: BIOSload version - another fix to callbios.fth, so the return values can be seen. Modified: cpu/x86/pc/biosload/callbios.fth Modified: cpu/x86/pc/biosload/callbios.fth ============================================================================== --- cpu/x86/pc/biosload/callbios.fth Thu May 26 11:46:46 2011 (r2231) +++ cpu/x86/pc/biosload/callbios.fth Thu May 26 23:23:22 2011 (r2232) @@ -73,25 +73,34 @@ label bios-ret 16-bit - bios-target # sp mov \ Set the stack pointer to the top of the rm reg area + cli + + \ The SS:SP is currently at bios-rflags+2, as a result of the "far ret" + \ in bios-call having popped bios-target and the IRET in the INT handler + \ having popped bios-retloc (32 bits) and bios-rflags (16 bits). + \ The next line moves SS:SP down so subsequents pushes will hit the + \ register area. + d# 10 # sp sub \ Copy the real-mode registers to the buffer op: pushf op: pusha ds push es push fs push gs push - cli - ax ax xor ax ds mov \ Assumes that the real-mode buffers are in the low 64K + pm-gdt-save >seg:off ( offset segment ) + # push ds pop ( offset ) \ Don't kill any other registers + op: #) lgdt ( ) - op: pm-gdt-save #) lgdt - cr0 ax mov 1 # al or ax cr0 mov + cr0 ax mov 1 # al or ax cr0 mov \ Switch to protected mode - here 5 + bios-ret - 'bios-ret + pm-code-desc #) far jmp + here 5 + bios-ret - 'bios-ret + pm-code-desc #) far jmp \ Jump to next location 32-bit + \ Reload descriptors with protected mode versions pm-data-desc # ax mov ax ds mov ax es mov ax gs mov ax gs mov ax ss mov - pm-idt-save #) lidt - pm-sp-save #) sp mov + pm-idt-save #) lidt \ Switch back to protected mode IDT + + pm-sp-save #) sp mov \ Switch back to protected mode stack popf popa c; @@ -114,8 +123,8 @@ bios-prepped? if exit then true to bios-prepped? bios-call 'bios-call /bios-call move bios-ret 'bios-ret /bios-ret move - h# ffff 'bios-idt w! - 0 'bios-idt 2+ l! + h# ffff 'bios-idt w! \ IDT size + 0 'bios-idt 2+ l! \ IDT base address bios-regs 'bios-sp seg:off! \ Setup real-mode full pointer for lss 'bios-ret bios-retloc seg:off! \ Setup return address full pointer bios-flagval bios-retloc 4 + w! \ Flags for return

1 0

[commit] r2231 - cpu/x86/pc/biosload
by repository service 26 May '11

26 May '11

Author: wmb Date: Thu May 26 11:46:46 2011 New Revision: 2231 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2231 Log: BIOSload version - now that callbios no longer kills the IDTR value, install the alarm handler and use hlt when waiting at the prompt, thus greatly reducing virtual CPU usage under emulators. Modified: cpu/x86/pc/biosload/fw.bth Modified: cpu/x86/pc/biosload/fw.bth ============================================================================== --- cpu/x86/pc/biosload/fw.bth Thu May 26 11:39:28 2011 (r2230) +++ cpu/x86/pc/biosload/fw.bth Thu May 26 11:46:46 2011 (r2231) @@ -339,6 +339,11 @@ [then] ; +\ This reduces processor use when waiting for a key. It helps +\ a lot when running on an emulator. +: c1-idle ( -- ) interrupts-enabled? if halt then ; +' c1-idle to stdin-idle + : startup ( -- ) standalone? 0= if exit then ." calibrate-ms" cr @@ -358,7 +363,8 @@ warning on only forth also definitions -\ install-alarm + ." Installing alarms" cr + install-alarm #line off

1 0

[commit] r2230 - cpu/x86/pc/biosload
by repository service 26 May '11

26 May '11

Author: wmb Date: Thu May 26 11:39:28 2011 New Revision: 2230 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2230 Log: BIOSload version - careful use of op: in callbios.fth to ensure that all bits of the GDT and IDT address are saved and restored. Modified: cpu/x86/pc/biosload/callbios.fth Modified: cpu/x86/pc/biosload/callbios.fth ============================================================================== --- cpu/x86/pc/biosload/callbios.fth Thu May 26 10:59:12 2011 (r2229) +++ cpu/x86/pc/biosload/callbios.fth Thu May 26 11:39:28 2011 (r2230) @@ -50,8 +50,8 @@ rm-data-desc # ax mov \ 16-bit data segment ax ds mov ax es mov ax fs mov ax gs mov ax ss mov - pm-gdt-save #) sgdt \ So we can get back - pm-idt-save #) sidt \ So we can get back + op: pm-gdt-save #) sgdt \ So we can get back + op: pm-idt-save #) sidt \ So we can get back 'bios-idt #) lidt cr0 ax mov h# fe # al and ax cr0 mov \ Enter real mode

1 0

[commit] r2229 - cpu/x86/pc/biosload
by repository service 26 May '11

26 May '11

Author: wmb Date: Thu May 26 10:59:12 2011 New Revision: 2229 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2229 Log: BIOSload version - changed the real-mode startup code so its GDT is compatible with callbios.fth, and fixed the virtualbox config to use a VESA console. Modified: cpu/x86/pc/biosload/biostart.bth cpu/x86/pc/biosload/config-virtualbox.fth cpu/x86/pc/biosload/fw.bth cpu/x86/pc/biosload/ofw.bth Modified: cpu/x86/pc/biosload/biostart.bth ============================================================================== --- cpu/x86/pc/biosload/biostart.bth Thu May 26 10:11:24 2011 (r2228) +++ cpu/x86/pc/biosload/biostart.bth Thu May 26 10:59:12 2011 (r2229) @@ -50,14 +50,16 @@ label gdt-template \ Will be copied to gdt-pa 0 le-w, 0 le-l, 0 le-w, \ 0 Mandatory null descriptor - 0 le-w, 0 le-l, 0 le-w, \ * Another null descriptor - ffff le-w, 9b.000000 le-l, 00.c.f le-w, \ 10 Code, linear=physical, 4GB - ffff le-w, 93.000000 le-l, 00.c.f le-w, \ 18 Data, linear=physical, 4GB + ffff le-w, 9b.000000 le-l, 0 le-w, \ 8 16-bit code, linear=physical, 64K + ffff le-w, 93.000000 le-l, 00.8.f le-w, \ 10 16-bit data, linear=physical, 4GB + ffff le-w, 93.000000 le-l, 0 le-w, \ 18 16-bit data, linear=physical, 64K + ffff le-w, 9b.000000 le-l, 00.c.f le-w, \ 20 Code, linear=physical, 4GB + ffff le-w, 93.000000 le-l, 00.c.f le-w, \ 28 Data, linear=physical, 4GB end-code label gdt-end end-code label gdt-ptr \ GDT limit + address - 1f le-w, gdt-pa le-l, \ # slots (3 * 8 - 1) , starting address + 2f le-w, gdt-pa le-l, \ # slots (3 * 8 - 1) , starting address end-code h# 100 pad-to \ space for stack @@ -191,7 +193,7 @@ \ Execute a far jump to following code to reload CS with a \ protected mode selector. The offset portion of the address \ (here asm-base - 7 +) has been relocated by the code above. - op: here asm-base - 7 + 10 #) far jmp + op: here asm-base - 7 + 20 #) far jmp 32-bit \ The following 2 lines execute at compile time, patching the @@ -202,7 +204,7 @@ here asm-base - 6 - r> le-w! \ set segment registers - 18 # bx mov \ Data segment selector + 28 # bx mov \ Data segment selector bx ds mov \ Set segment register bx es mov \ Set segment register bx fs mov \ Set segment register Modified: cpu/x86/pc/biosload/config-virtualbox.fth ============================================================================== --- cpu/x86/pc/biosload/config-virtualbox.fth Thu May 26 10:11:24 2011 (r2228) +++ cpu/x86/pc/biosload/config-virtualbox.fth Thu May 26 10:59:12 2011 (r2229) @@ -10,6 +10,8 @@ \ create debug-startup \ create serial-console +create pc + create resident-packages create addresses-assigned \ Don't reassign PCI addresses \ create virtual-mode @@ -17,7 +19,8 @@ create use-timestamp-counter create use-pci-isa create use-isa-ide -create use-ega +\ create use-ega +create use-vesa create use-elf \ create use-ne2000 create use-watch-all Modified: cpu/x86/pc/biosload/fw.bth ============================================================================== --- cpu/x86/pc/biosload/fw.bth Thu May 26 10:11:24 2011 (r2228) +++ cpu/x86/pc/biosload/fw.bth Thu May 26 10:59:12 2011 (r2229) @@ -186,10 +186,7 @@ fload ${BP}/cpu/x86/pc/rmtools.fth fload ${BP}/cpu/x86/pc/biosload/callbios.fth - -[ifdef] syslinux-loaded fload ${BP}/cpu/x86/pc/biosload/callvbe.fth -[then] fload ${BP}/cpu/x86/pc/biosload/devices.fth Modified: cpu/x86/pc/biosload/ofw.bth ============================================================================== --- cpu/x86/pc/biosload/ofw.bth Thu May 26 10:11:24 2011 (r2228) +++ cpu/x86/pc/biosload/ofw.bth Thu May 26 10:59:12 2011 (r2229) @@ -1,7 +1,7 @@ purpose: Construct the final BIOS-start OFW image command: &builder &this -\ in: biostart.img +in: biostart.img in: reset.di in: start.di in: ${BP}/cpu/x86/pc/biosload/build/paging.di

1 0

[commit] r2228 - cpu/x86/pc/biosload
by repository service 26 May '11

26 May '11

Author: wmb Date: Thu May 26 10:11:24 2011 New Revision: 2228 URL: http://tracker.coreboot.org/trac/openfirmware/changeset/2228 Log: BIOSload version - added floppy image format to ofw.bth for virtualbox config Modified: cpu/x86/pc/biosload/config-virtualbox.fth cpu/x86/pc/biosload/ofw.bth Modified: cpu/x86/pc/biosload/config-virtualbox.fth ============================================================================== --- cpu/x86/pc/biosload/config-virtualbox.fth Thu May 26 02:16:32 2011 (r2227) +++ cpu/x86/pc/biosload/config-virtualbox.fth Thu May 26 10:11:24 2011 (r2228) @@ -6,6 +6,7 @@ \ Load and run in VirtualBox (also works for other emulators) create virtualbox-loaded +create real-mode-entry \ create debug-startup \ create serial-console Modified: cpu/x86/pc/biosload/ofw.bth ============================================================================== --- cpu/x86/pc/biosload/ofw.bth Thu May 26 02:16:32 2011 (r2227) +++ cpu/x86/pc/biosload/ofw.bth Thu May 26 10:11:24 2011 (r2228) @@ -36,6 +36,10 @@ hex +[ifdef] virtualbox-loaded +writing floppyofw.img +[then] + [ifdef] grub-loaded fload ${BP}/cpu/x86/pc/elfhdr.fth .( --- Saving as ofwgrub.elf - GRUB multiboot format) cr

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

openfirmware