[flashrom] Tyan S2915-E flash detection problem (HP board)

[Phil]

Hiya,


I'll add my Tyan S2915 to the mix, as it  also does not find the chip:

they are attacched, but I do not know if this is visible or not...


Cheers

PHiL




Nicolas AVELINE wrote:
> Hello !
>
> my tyan :
>
> S2915-E AS#408544-004
> *
>
> root at Serveur:~# flashrom -V*
> flashrom v0.9.1-r877
> No coreboot table found.
> DMI string 0: "Hewlett-Packard"
> DMI string 1: "HP xw9400 Workstation"
> DMI string 2: " "
> DMI string 3: "Hewlett-Packard"
> DMI string 4: "0A1Ch"
> DMI string 5: "E"
> Found chipset "NVIDIA MCP55", enabling flash write... OK.
> This chipset supports the following protocols: Non-SPI.
> Calibrating delay loop... 478M loops per second, 100 myus = 255 us. OK.
> Probing for AMD Am29F010A/B, 128 KB: probe_29f040b: id1 0x24, id2 0x50
> Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2 0xff
> Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
> Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0x41, id2 
> 0x4d, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
> Probing for AMD Am29LV081B, 1024 KB: probe_29f040b: id1 0x41, id2 0x4d
> Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0xe9, id2 
> 0x6d, id1 is normal flash content, id2 is normal flash content
> Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0xe9, id2 
> 0x6d, id1 is normal flash content, id2 is normal flash content
> Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xff, id2 0xd3
> Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xff, id2 0xd3
> Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
> Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0xff, 
> id2 0xff
> Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0xff, 
> id2 0xff
> Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0x24, 
> id2 0x50, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0x24, 
> id2 0x50, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff
> Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x41, id2 0x4d
> Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix MX29F001B, 128 KB: probe_29f002: id1 0x24, id2 0x50
> Probing for Macronix MX29F001T, 128 KB: probe_29f002: id1 0x24, id2 0x50
> Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xff, id2 0xd3
> Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xff, id2 0xd3
> Probing for Macronix MX29LV040, 512 KB: probe_29f002: id1 0xff, id2 0xff
> Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for PMC Pm29F002T, 256 KB: probe_29f040b: id1 0xff, id2 0xd3
> Probing for PMC Pm29F002B, 256 KB: probe_29f040b: id1 0xff, id2 0xd3
> Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Sharp LHF00L04, 1024 KB: probe_49lfxxxc: id1 0x41, id2 0x4d
> Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0xff, id2 0xff
> Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0xe9, id2 
> 0x6d, id1 is normal flash content, id2 is normal flash content
> Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0x41, id2 
> 0x4d, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0xff, id2 0xff
> Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x41, 
> id2 0x4d, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0x41, id2 0x4d
> Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
> Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0x41, 
> id2 0x4d, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2 0xff
> Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip 
> bus type SPI are incompatible.
> Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip 
> bus type SPI are incompatible.
> Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0xff, id2 0xff
> Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff
> Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for ST M50FLW040A, 512 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for ST M50FLW040B, 512 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for ST M50FLW080A, 1024 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0x41, 
> id2 0x4d, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for ST M50FLW080B, 1024 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0x41, 
> id2 0x4d, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2 0xd3
> Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff
> Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff
> Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x41, id2 0x4d
> Probing for ST M50LPW116, 2048 KB: probe_jedec_common: id1 0xff, id2 
> 0xff, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0x24, 
> id2 0x50, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0xff, id2 
> 0xd3, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and 
> chip bus type SPI are incompatible.
> Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI 
> and chip bus type SPI are incompatible.
> Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0x24, id2 
> 0x50, id1 parity violation, id1 is normal flash content, id2 is normal 
> flash content
> Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond 
> W29EE011 because the probing sequence puts the AMIC A49LF040A in a 
> funky state. Use 'flashrom -c W29EE011' if you have a board with this 
> chip.
> Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing 
> information, using default 10mS/40uS. probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xff, 
> id2 0xff, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0x41, 
> id2 0x4d, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, 
> id2 0xd3, id1 parity violation, id1 is normal flash content, id2 is 
> normal flash content
> Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe 
> timing information, using default 10mS/40uS. probe_jedec_common: id1 
> 0x41, id2 0x4d, id1 parity violation, id1 is normal flash content, id2 
> is normal flash content
> Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct 
> probe timing information, using default 10mS/40uS. probe_jedec_common: 
> id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, 
> id2 is normal flash content
> Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host 
> bus type Non-SPI and chip bus type SPI are incompatible.
> Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type 
> Non-SPI and chip bus type SPI are incompatible.
> Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus 
> type Non-SPI and chip bus type SPI are incompatible.
> Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus 
> type Non-SPI and chip bus type SPI are incompatible.
> No EEPROM/flash device found.
> If you know which flash chip you have, and if this version of flashrom
> supports a similar flash chip, you can try to force read your chip. Run:
> flashrom -f -r -c similar_supported_flash_chip filename
>
> Note: flashrom can never write when the flash chip isn't found 
> automatically.
>
> *root at Serveur:~# superiotool -deV*
> superiotool r3844
> Probing for ALi Super I/O at 0x3f0...
>   Failed. Returned data: id=0x0000, rev=0x00
> Probing for ALi Super I/O at 0x370...
>   Failed. Returned data: id=0xffff, rev=0xff
> Probing for Fintek Super I/O at 0x2e...
>   Failed. Returned data: vid=0x0400, id=0x0081
> Probing for Fintek Super I/O at 0x4e...
>   Failed. Returned data: vid=0xffff, id=0xffff
> Probing for ITE Super I/O (init=standard) at 0x2e...
>   Failed. Returned data: id=0x8100, rev=0x1
> Probing for ITE Super I/O (init=it8761e) at 0x2e...
>   Failed. Returned data: id=0x8100, rev=0x1
> Probing for ITE Super I/O (init=it8228e) at 0x2e...
>   Failed. Returned data: id=0x8100, rev=0x1
> Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
>   Failed. Returned data: id=0x8100, rev=0x1
> Probing for ITE Super I/O (init=standard) at 0x4e...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for ITE Super I/O (init=it8761e) at 0x4e...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for ITE Super I/O (init=it8228e) at 0x4e...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...
>   Failed. Returned data: id=0xffff, rev=0xf
> Probing for NSC Super I/O at 0x2e...
>   Failed. Returned data: port=0xff, port+1=0xff
> Probing for NSC Super I/O at 0x4e...
>   Failed. Returned data: port=0xff, port+1=0xff
> Probing for NSC Super I/O at 0x15c...
>   Failed. Returned data: port=0xff, port+1=0xff
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
> Found SMSC SCH5307 (id=0x81, rev=0x00) at 0x2e
> No dump available for this Super I/O
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
>   Failed. Returned data: id=0x00, rev=0x00
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
> Found SMSC FDC37N972 (id=0x0b, rev=0x00) at 0x4e
> Register dump:
> idx 02 20 21 22 23 24 25 26  27 28 29 2a 2b 2c 2d 2e  2f
> val 00 0b 00 00 00 00 00 4e  00 00 00 00 00 00 00 00  00
> def 00 0b 00 00 00 04 04 NA  NA 00 00 00 00 00 00 00  00
> LDN 0x00 (Floppy)
> idx 30 60 61 70 74 f0 f1 f2  f3 f4 f5
> val 01 04 c0 00 00 00 d1 15  0b 00 10
> def 00 03 f0 06 02 0e 00 ff  RR 00 00
> LDN 0x01 (Power Management (PM1))
> idx 30 60 61
> val 01 04 c0
> def 00 00 00
> LDN 0x03 (Parallel port)
> idx 30 60 61 70 74 f0 f1
> val 01 04 c0 00 00 00 d1
> def 00 00 00 00 04 3c 00
> LDN 0x04 (COM1)
> idx 30 60 61 70 f0
> val 01 04 c0 00 00
> def 00 00 00 00 00
> LDN 0x05 (COM2)
> idx 30 60 61 62 63 70 74 f0  f1 f2 f7 f8
> val 01 04 c0 00 00 00 00 00  d1 15 00 00
> def 00 00 00 00 00 00 04 00  02 03 00 00
> LDN 0x06 (Real-time clock (RTC))
> idx 30 60 61 62 63 70 f0 f1
> val 01 04 c0 00 00 00 00 d1
> def 00 00 70 00 74 00 00 NA
> LDN 0x07 (Keyboard)
> idx 30 60 61 70 72 f0
> val 01 04 c0 00 00 00
> def 00 00 00 00 00 00
> LDN 0x08 (Embedded Controller (EC))
> idx 30 60 61
> val 01 04 c0
> def 00 00 62
> LDN 0x09 (Mailbox)
> idx 30 60 61
> val 01 04 c0
> def 00 00 00
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
>   Failed. Returned data: id=0x00, rev=0x00
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
>   Failed. Returned data: id=0x00, rev=0x00
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
>   Failed. Returned data: id=0x00, rev=0x00
> Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
>   Failed. Returned data: id=0xff, rev=0xff
> Probing for Winbond Super I/O (init=0x88) at 0x2e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x89) at 0x2e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x88) at 0x4e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x89) at 0x4e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x88) at 0x3f0...
>   Failed. Returned data: id/oldid=0x00/0x00, rev=0x00
> Probing for Winbond Super I/O (init=0x89) at 0x3f0...
>   Failed. Returned data: id/oldid=0x00/0x00, rev=0x00
> Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
>   Failed. Returned data: id/oldid=0x00/0x00, rev=0x00
> Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
>   Failed. Returned data: id/oldid=0x00/0x00, rev=0x00
> Probing for Winbond Super I/O (init=0x88) at 0x370...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x89) at 0x370...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x88) at 0x250...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x89) at 0x250...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
> Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
>   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
>
>
> *root at Serveur:~# lspci -nnvvvxxx*
> 0000:00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory 
> Controller [10de:0369] (rev a2)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0
>     Capabilities: [44] HyperTransport: Slave or Primary Interface
>         Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
>         Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- 
> LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
>         Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ 
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
>         Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit 
> DwFcInEn- LWO=8bit DwFcOutEn-
>         Revision ID: 1.03
>         Link Frequency 0: 1.0GHz
>         Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
>         Link Frequency 1: 200MHz
>         Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 
> 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- 
> SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
>         Prefetchable memory behind bridge Upper: 00-00
>         Bus Number: 00
>     Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed-
>         Mapping Address Base: 00000000fee00000
> 00: de 10 69 03 06 01 b0 00 a2 00 00 05 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00
> 40: 3c 10 fe 12 08 dc e0 01 22 20 11 11 d0 00 00 00
> 50: 23 06 7f 00 03 00 00 00 00 00 03 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 38 0a 00
> 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00
> 80: 23 99 88 00 fa 00 64 0e 02 00 00 00 7f 00 00 00
> 90: 78 00 00 90 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00
> c0: 02 00 00 00 00 00 00 00 00 00 00 00 80 00 0f 0f
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8
> e0: 00 00 e0 fe 00 00 00 00 00 00 80 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge 
> [10de:0364] (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0
> 00: de 10 64 03 0f 00 a0 00 a3 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
> 40: 3c 10 fe 12 00 00 00 00 fa 3e ff 00 de fd 00 00
> 50: fa 3e ff 00 00 5a 62 02 00 00 00 01 00 00 ff ff
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 ff
> 70: 10 00 ff ff c1 80 00 00 00 00 64 19 03 00 00 10
> 80: 09 c0 00 2d 16 24 00 80 ff 00 00 01 ff 00 00 00
> 90: 00 08 00 00 00 00 00 00 21 47 95 86 ef cd ab 00
> a0: a3 00 10 10 00 00 00 00 00 04 cb 04 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 50 28 00 fe fd e1 00 b0
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
>
> 0000:00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] 
> (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Interrupt: pin A routed to IRQ 10
>     Region 4: I/O ports at 3000 [size=64]
>     Region 5: I/O ports at 3040 [size=64]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Kernel driver in use: nForce2_smbus
>     Kernel modules: i2c-nforce2
> 00: de 10 68 03 01 00 b0 00 a3 00 05 0c 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 30 00 00 41 30 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 00 00
> 40: 3c 10 fe 12 01 00 02 c0 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 f8 00 00 01 f9 00 00 01 fa 00 00 00 f0 ef fd
> 70: 01 00 00 00 00 00 e0 fc 00 00 00 00 01 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: d4 30 80 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 64 15 05 00 b5 03 00 07 80 30 00 00 77 44 44 11
> f0: 5a ff 5f 3f 00 00 00 c0 10 00 00 00 00 00 00 00
>
> 0000:00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB 
> Controller [10de:036c] (rev a1) (prog-if 10)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Interrupt: pin A routed to IRQ 18
>     Region 0: Memory at fce44000 (32-bit, non-prefetchable) [size=4K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Kernel driver in use: ohci_hcd
> 00: de 10 6c 03 07 00 b0 00 a1 10 03 0c 00 00 80 00
> 10: 00 40 e4 fc 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 03 01
> 40: 3c 10 fe 12 01 00 02 fe 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 1d 47 40 00 10 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
>
> 0000:00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB 
> Controller [10de:036d] (rev a2) (prog-if 20)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Interrupt: pin B routed to IRQ 19
>     Region 0: Memory at fce4a000 (32-bit, non-prefetchable) [size=256]
>     Capabilities: [44] Debug port: BAR=1 offset=0098
>     Capabilities: [80] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Kernel driver in use: ehci_hcd
> 00: de 10 6d 03 06 00 b0 00 a2 20 03 0c 00 00 80 00
> 10: 00 a0 e4 fc 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 02 03 01
> 40: 3c 10 fe 12 0a 80 98 20 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 20 20 01 00 00 60 18 85 03 3c 3f 01 00 00 00 00
> 70: 00 00 08 00 00 10 20 80 89 3d b6 22 77 25 64 00
> 80: 01 00 02 fe 00 00 00 00 00 00 00 00 15 16 00 00
> 90: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 01 00 00 00 00 00 08 80 00 00 00 00 00 00 00 00
> b0: 44 44 00 00 00 00 00 00 ff 03 00 00 00 00 00 00
> c0: 10 10 2d 0d 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
>
> 0000:00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE 
> [10de:036e] (rev a1) (prog-if 8a [Master SecP PriP])
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) 
> [disabled] [size=8]
>     Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) 
> [disabled] [size=1]
>     Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) 
> [disabled] [size=8]
>     Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) 
> [disabled] [size=1]
>     Region 4: I/O ports at 3080 [size=16]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Kernel driver in use: pata_amd
> 00: de 10 6e 03 05 00 b0 00 a1 8a 01 01 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 81 30 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01
> 40: 3c 10 fe 12 01 00 02 00 00 00 00 00 00 00 00 00
> 50: 02 80 00 00 00 00 00 00 99 99 20 20 0a 00 a8 20
> 60: 00 00 c4 c6 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 c0 91 e7 00 00 02 34 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 01
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
>
> 0000:00:05.0 IDE interface [0101]: nVidia Corporation MCP55 SATA 
> Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Interrupt: pin A routed to IRQ 22
>     Region 0: I/O ports at 30c0 [size=8]
>     Region 1: I/O ports at 3100 [size=4]
>     Region 2: I/O ports at 30c8 [size=8]
>     Region 3: I/O ports at 3104 [size=4]
>     Region 4: I/O ports at 3090 [size=16]
>     Region 5: Memory at fce45000 (32-bit, non-prefetchable) [size=4K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/2 Enable-
>         Address: 0000000000000000  Data: 0000
>     Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: sata_nv
> 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00
> 10: c1 30 00 00 01 31 00 00 c9 30 00 00 05 31 00 00
> 20: 91 30 00 00 00 50 e4 fc 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 03 01
> 40: 3c 10 fe 12 01 b0 02 00 00 00 00 00 00 00 00 00
> 50: 0f 68 08 80 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00
> 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 00
> 80: 00 00 00 c0 d7 fb c7 bb 00 00 0b 03 fd bc 0e 6f
> 90: 00 00 ff 3d 00 00 00 00 06 00 06 10 7f 03 01 01
> a0: 12 0a 00 00 c0 00 00 00 00 00 00 00 33 31 00 02
> b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8
> d0: 0a 00 02 65 42 00 00 00 00 00 00 00 01 00 e0 07
> e0: 0a 00 02 65 42 00 00 00 00 00 00 00 00 00 10 00
> f0: 00 00 00 00 00 00 00 00 12 00 0c 00 00 00 00 00
>
> 0000:00:05.1 IDE interface [0101]: nVidia Corporation MCP55 SATA 
> Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Interrupt: pin B routed to IRQ 21
>     Region 0: I/O ports at 30d0 [size=8]
>     Region 1: I/O ports at 3108 [size=4]
>     Region 2: I/O ports at 30d8 [size=8]
>     Region 3: I/O ports at 310c [size=4]
>     Region 4: I/O ports at 30a0 [size=16]
>     Region 5: Memory at fce46000 (32-bit, non-prefetchable) [size=4K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/2 Enable-
>         Address: 0000000000000000  Data: 0000
>     Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: sata_nv
> 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00
> 10: d1 30 00 00 09 31 00 00 d9 30 00 00 0d 31 00 00
> 20: a1 30 00 00 00 60 e4 fc 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 02 03 01
> 40: 3c 10 fe 12 01 b0 02 00 00 00 00 00 00 00 00 00
> 50: 0f 68 08 80 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00
> 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 00
> 80: 00 00 00 c0 6f fd 7f bb 00 00 0f 03 fb f7 f8 73
> 90: 00 00 23 3f 00 00 00 00 06 00 06 10 7f 03 01 01
> a0: 12 0a 00 00 c0 00 00 00 00 00 00 00 33 31 00 02
> b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8
> d0: 0a 00 02 65 42 00 00 00 00 00 00 00 00 00 90 00
> e0: 0a 00 02 65 42 00 00 00 00 00 00 00 00 a1 80 02
> f0: 00 00 00 00 00 00 00 00 12 00 0c 00 00 00 00 00
>
> 0000:00:05.2 IDE interface [0101]: nVidia Corporation MCP55 SATA 
> Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO])
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (750ns min, 250ns max)
>     Interrupt: pin C routed to IRQ 20
>     Region 0: I/O ports at 30e0 [size=8]
>     Region 1: I/O ports at 3110 [size=4]
>     Region 2: I/O ports at 30e8 [size=8]
>     Region 3: I/O ports at 3114 [size=4]
>     Region 4: I/O ports at 30b0 [size=16]
>     Region 5: Memory at fce47000 (32-bit, non-prefetchable) [size=4K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/2 Enable-
>         Address: 0000000000000000  Data: 0000
>     Capabilities: [cc] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: sata_nv
> 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00
> 10: e1 30 00 00 11 31 00 00 e9 30 00 00 15 31 00 00
> 20: b1 30 00 00 00 70 e4 fc 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 03 03 01
> 40: 3c 10 fe 12 01 b0 02 00 00 00 00 00 00 00 00 00
> 50: 0f 68 08 80 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00
> 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 00
> 80: 00 00 00 c0 be 7d fb fc 00 00 eb 12 0c bd f7 bd
> 90: 00 00 92 18 00 00 00 00 06 00 06 10 7f 03 01 01
> a0: 12 0a 00 00 c0 00 00 00 00 00 00 00 33 31 00 02
> b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 02 a8
> d0: 0a 00 02 76 42 00 00 00 00 00 00 00 00 03 00 04
> e0: 0a 00 02 76 42 00 00 00 00 00 00 00 00 00 f0 07
> f0: 00 00 00 00 00 00 00 00 10 00 0c 00 00 00 00 00
>
> 0000:00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge 
> [10de:0370] (rev a2) (prog-if 01)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0
>     Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
>     I/O behind bridge: 0000f000-00000fff
>     Memory behind bridge: fc400000-fccfffff
>     Prefetchable memory behind bridge: f8000000-f80fffff
>     Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- <SERR- <PERR-
>     BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
>         PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn+
>     Capabilities: [b8] Subsystem: nVidia Corporation Device [10de:cb84]
>     Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed-
>         Mapping Address Base: 00000000fee00000
> 00: de 10 70 03 07 01 b0 00 a2 01 04 06 00 00 81 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 20 f0 00 80 02
> 20: 40 fc c0 fc 00 f8 00 f8 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 b8 00 00 00 00 00 00 00 ff 00 0a 0a
> 40: 00 00 33 07 01 00 02 00 05 00 00 00 00 00 48 00
> 50: 00 00 fe ef 00 00 00 00 ff 1f ff 1f 03 00 84 00
> 60: 00 00 85 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 fe 0f 01 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 a8
> 90: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 06 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
> b0: 00 00 00 00 ff ff 00 00 0d 8c 00 00 de 10 84 cb
> c0: de 10 84 cb 03 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:06.1 Audio device [0403]: nVidia Corporation MCP55 High 
> Definition Audio [10de:0371] (rev a2)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (500ns min, 1250ns max)
>     Interrupt: pin B routed to IRQ 22
>     Region 0: Memory at fce40000 (32-bit, non-prefetchable) [size=16K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ 
> Queue=0/0 Enable-
>         Address: 0000000000000000  Data: 0000
>         Masking: 00000000  Pending: 00000000
>     Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: HDA Intel
>     Kernel modules: snd-hda-intel
> 00: de 10 71 03 06 00 b0 00 a2 00 03 04 00 00 80 00
> 10: 00 00 e4 fc 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 02 05
> 40: 3c 10 fe 12 01 50 02 c0 00 00 00 00 01 01 0f 00
> 50: 05 6c 80 01 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 02 a8
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 47 10 29 00 00 00 00 00 00
>
> 0000:00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet 
> [10de:0373] (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx+
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (250ns min, 5000ns max)
>     Interrupt: pin A routed to IRQ 50
>     Region 0: Memory at fce48000 (32-bit, non-prefetchable) [size=4K]
>     Region 1: I/O ports at 30f0 [size=8]
>     Region 2: Memory at fce4a100 (32-bit, non-prefetchable) [size=256]
>     Region 3: Memory at fce4a300 (32-bit, non-prefetchable) [size=16]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
>     Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
>         Vector table: BAR=2 offset=00000000
>         PBA: BAR=3 offset=00000000
>     Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ 
> Queue=0/3 Enable+
>         Address: 00000000feeff00c  Data: 41a1
>         Masking: 000000fe  Pending: 00000000
>     Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: forcedeth
>     Kernel modules: forcedeth
> 00: de 10 73 03 07 04 b0 00 a3 00 80 06 00 00 00 00
> 10: 00 80 e4 fc f1 30 00 00 00 a1 e4 fc 00 a3 e4 fc
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 01 14
> 40: 3c 10 fe 12 01 70 02 fe 00 01 00 00 01 00 00 00
> 50: 05 6c 87 01 0c f0 ef fe 00 00 00 00 a1 41 00 00
> 60: fe 00 00 00 00 00 00 00 ff 00 00 00 08 00 02 a8
> 70: 11 50 07 00 02 00 00 00 03 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 11 00 00 00 52 01 00 00 00 00 00 00
>
> 0000:00:09.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet 
> [10de:0373] (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx+
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0 (250ns min, 5000ns max)
>     Interrupt: pin A routed to IRQ 51
>     Region 0: Memory at fce49000 (32-bit, non-prefetchable) [size=4K]
>     Region 1: I/O ports at 30f8 [size=8]
>     Region 2: Memory at fce4a200 (32-bit, non-prefetchable) [size=256]
>     Region 3: Memory at fce4a310 (32-bit, non-prefetchable) [size=16]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
>     Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
>         Vector table: BAR=2 offset=00000000
>         PBA: BAR=3 offset=00000000
>     Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ 
> Queue=0/3 Enable+
>         Address: 00000000feeff00c  Data: 41a9
>         Masking: 000000fe  Pending: 00000000
>     Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
>     Kernel driver in use: forcedeth
>     Kernel modules: forcedeth
> 00: de 10 73 03 07 04 b0 00 a3 00 80 06 00 00 00 00
> 10: 00 90 e4 fc f9 30 00 00 00 a2 e4 fc 10 a3 e4 fc
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 01 14
> 40: 3c 10 fe 12 01 70 02 fe 00 01 00 00 00 00 00 00
> 50: 05 6c 87 01 0c f0 ef fe 00 00 00 00 a9 41 00 00
> 60: fe 00 00 00 00 00 00 00 ff 00 00 00 08 00 02 a8
> 70: 11 50 07 00 02 00 00 00 03 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 11 00 00 00 52 01 00 00 00 00 00 00
>
> 0000:00:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express 
> bridge [10de:0378] (rev a3)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx+
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0, Cache Line Size: 64 bytes
>     Bus: primary=00, secondary=2b, subordinate=2d, sec-latency=0
>     I/O behind bridge: 0000f000-00000fff
>     Memory behind bridge: fcd00000-fcdfffff
>     Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
>     Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>     BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
>         PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>     Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
>     Capabilities: [48] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/1 Enable+
>         Address: 00000000feeff00c  Data: 4151
>     Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>         Mapping Address Base: 00000000fee00000
>     Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
>         DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s 
> <64ns, L1 <1us
>             ExtTag- RBE+ FLReset-
>         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>             RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>             MaxPayload 128 bytes, MaxReadReq 512 bytes
>         DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>         LnkCap:    Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, 
> Latency L0 <512ns, L1 <4us
>             ClockPM- Suprise- LLActRep+ BwNot-
>         LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
>             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>         LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ 
> DLActive+ BWMgmt- ABWMgmt-
>         SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
> Surpise-
>             Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
>         SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>             Control: AttnInd Off, PwrInd On, Power- Interlock-
>         SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
> Interlock-
>             Changed: MRL- PresDet+ LinkState+
>         RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
> CRSVisible-
>         RootCap: CRSVisible-
>         RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>     Capabilities: [100] Virtual Channel <?>
>     Capabilities: [160] Advanced Error Reporting <?>
>     Kernel driver in use: pcieport-driver
>     Kernel modules: shpchp
> 00: de 10 78 03 07 05 10 00 a3 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 2b 2d 00 f1 01 00 20
> 20: d0 fc d0 fc f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 02 00
> 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00
> 50: 05 60 83 00 0c f0 ef fe 00 00 00 00 51 41 00 00
> 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 10 00 41 01 01 80 00 00 10 28 00 00 41 3c 11 02
> 90: 00 00 41 30 00 00 00 00 c0 01 48 01 04 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Capabilities: [80] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
>     Capabilities: [a0] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
>     Capabilities: [c0] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
> 00: 22 10 00 12 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 02 14 00 04 04 04 00 01 02 04 00 01 02 04 00
> 50: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00
> 60: 10 00 07 00 e0 02 00 00 20 c8 4e 00 10 0a 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 a0 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> 90: 44 99 8a 04 00 00 00 00 03 00 00 00 00 00 00 00
> a0: 08 c0 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> b0: 44 99 8a 04 00 00 00 00 03 00 00 00 00 00 00 00
> c0: 08 00 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> d0: 92 02 85 04 00 00 00 00 07 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Address Map [1022:1201]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> 00: 22 10 01 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 7f 00 03 00 80 00 01 00 0f 01
> 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
> 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
> 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
> 80: 03 0a 00 00 20 0b 00 00 03 00 f4 00 81 ff f7 00
> 90: 03 40 fc 00 20 ef fc 00 03 f0 fc 00 01 0f fd 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 13 30 00 00 20 30 00 00 03 10 00 00 01 20 00 00
> d0: 00 00 00 00 00 00 00 00 03 e0 00 00 01 e0 00 00
> e0: 03 02 00 3f 13 00 40 ff 00 00 00 00 00 00 00 00
> f0: 02 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Kernel driver in use: amd64_edac
>     Kernel modules: amd64_edac_mod
> 00: 22 10 02 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 e0 3f 38 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 05 00 c0 0e 00 00 00 00
> 80: 60 00 00 00 00 00 00 00 24 ca 69 ef 34 03 82 00
> 90: 10 21 08 00 0a 80 48 6f 2a 00 00 80 05 00 06 00
> a0: 00 02 00 00 00 00 00 00 02 00 00 00 00 00 00 00
> b0: 90 8f a0 1e c1 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Capabilities: [f0] Secure device <?>
> 00: 22 10 03 12 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
> 40: ff ff ff 3f 5c 00 70 4a 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 10 10 12 10 01 57 81 1b
> 60: 00 00 00 00 04 00 7f 42 00 00 00 40 52 80 01 00
> 70: 53 11 04 00 11 11 08 00 14 0c 20 00 14 09 09 00
> 80: 81 87 00 e6 e6 41 e6 80 08 00 00 00 10 40 40 00
> 90: 03 00 00 00 10 00 00 00 00 98 7d 00 00 00 00 00
> a0: 00 28 01 a0 80 18 8c 09 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 1a 29 02 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 24 0f 31 c3 14 1c 00 03 28 54 00 00
> e0: 00 00 00 00 30 15 00 00 9f 77 f0 02 00 00 00 00
> f0: 0f 00 10 00 00 00 00 00 00 00 00 00 21 0f 10 00
>
> 0000:00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Link Control [1022:1204]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> 00: 22 10 04 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.0 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] HyperTransport Configuration [1022:1200]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Capabilities: [80] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
>     Capabilities: [a0] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
>     Capabilities: [c0] HyperTransport: Host or Secondary Interface
>         Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- 
> <EOCErr- DUL-
>         Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
>         Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit 
> DwFcInEn- LWO=16bit DwFcOutEn-
>         Revision ID: 3.00
>         Link Frequency: 1.0GHz
>         Link Error: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ 
> UIDRD- ExtRS- UCnfE-
> 00: 22 10 00 12 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 08 08 04 00 01 02 24 00 01 02 04 00 01 02 04 00
> 50: 01 02 04 00 01 02 04 00 01 02 04 00 01 02 04 00
> 60: 11 00 07 00 e0 00 00 00 20 c8 4e 00 08 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 a0 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> 90: 92 02 85 04 00 40 00 00 07 00 00 00 00 00 00 00
> a0: 08 c0 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> b0: 44 99 8a 04 00 00 00 00 03 00 00 00 00 00 00 00
> c0: 08 00 01 21 20 20 11 11 60 06 75 80 13 00 00 00
> d0: 44 99 8a 04 00 00 00 00 03 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.1 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Address Map [1022:1201]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> 00: 22 10 01 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 7f 00 03 00 80 00 01 00 0f 01
> 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
> 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
> 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
> 80: 03 0a 00 00 20 0b 00 00 03 00 f4 00 81 ff f7 00
> 90: 03 40 fc 00 20 ef fc 00 03 f0 fc 00 01 0f fd 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 13 30 00 00 20 30 00 00 03 10 00 00 01 20 00 00
> d0: 00 00 00 00 00 00 00 00 03 e0 00 00 01 e0 00 00
> e0: 03 02 00 3f 13 00 40 ff 00 00 00 00 00 00 00 00
> f0: 03 90 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.2 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] DRAM Controller [1022:1202]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Kernel driver in use: amd64_edac
>     Kernel modules: amd64_edac_mod
> 00: 22 10 02 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 e0 3f 38 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 05 00 00 0f 00 00 00 00
> 80: 60 00 00 00 00 00 00 00 24 ca 69 ef 34 03 82 00
> 90: 10 21 08 00 0a 80 48 6f 2a 00 00 80 05 00 08 00
> a0: 00 02 00 00 00 00 00 00 02 00 00 00 00 00 00 00
> b0: b8 19 8c 1f c1 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.3 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Miscellaneous Control [1022:1203]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Capabilities: [f0] Secure device <?>
> 00: 22 10 03 12 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
> 40: ff ff ff 3f 5c 00 70 4a 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 10 10 12 10 01 59 81 9b
> 60: 00 00 00 00 04 00 7f 42 00 00 00 40 52 80 01 00
> 70: 53 11 04 00 11 11 08 00 14 0c 20 00 14 09 09 00
> 80: 81 87 00 e6 e6 41 e6 80 08 00 00 00 10 40 40 00
> 90: 03 00 00 00 10 00 00 00 00 98 7d 00 00 00 00 00
> a0: 00 28 01 a0 80 18 8c 0f 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 24 0f 31 c3 14 1c 00 03 28 54 00 00
> e0: 00 00 00 00 30 15 00 00 9f 77 f0 02 00 00 00 00
> f0: 0f 00 10 00 00 00 00 00 00 00 00 00 21 0f 10 00
>
> 0000:00:19.4 Host bridge [0600]: Advanced Micro Devices [AMD] K10 
> [Opteron, Athlon64, Sempron] Link Control [1022:1204]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
> 00: 22 10 04 12 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:04.0 VGA compatible controller [0300]: Trident Microsystems 
> TGUI 9660/938x/968x [1023:9660] (rev d3)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort+ <MAbort+ >SERR- <PERR- INTx-
>     Latency: 32
>     Interrupt: pin A routed to IRQ 5
>     Region 0: Memory at fc400000 (32-bit, non-prefetchable) [size=4M]
>     Region 1: Memory at fcc00000 (32-bit, non-prefetchable) [size=64K]
>     Region 2: Memory at fc800000 (32-bit, non-prefetchable) [size=4M]
>     [virtual] Expansion ROM at f8000000 [disabled] [size=64K]
>     Kernel modules: tridentfb
> 00: 23 10 60 96 07 00 00 32 d3 00 00 03 00 20 00 00
> 10: 00 00 40 fc 00 00 c0 fc 00 00 80 fc 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:05.0 FireWire (IEEE 1394) [0c00]: Texas Instruments 
> TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
>     Interrupt: pin A routed to IRQ 16
>     Region 0: Memory at fcc14000 (32-bit, non-prefetchable) [size=2K]
>     Region 1: Memory at fcc10000 (32-bit, non-prefetchable) [size=16K]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME+
>     Kernel driver in use: ohci1394
>     Kernel modules: firewire-ohci, ohci1394
> 00: 4c 10 23 80 06 01 10 02 00 10 00 0c 10 20 00 00
> 10: 00 40 c1 fc 00 00 c1 fc 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 01 02 04
> 40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 88 00 00 00
> f0: 10 00 00 00 82 00 00 00 3c 10 fe 12 00 00 00 00
>
> 0000:2b:00.0 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express 
> - PCI/PCI-X Bridge [1033:0125] (rev 06)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0, Cache Line Size: 64 bytes
>     Bus: primary=2b, secondary=2c, subordinate=2c, sec-latency=32
>     I/O behind bridge: 0000f000-00000fff
>     Memory behind bridge: fff00000-000fffff
>     Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
>     Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>     BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
>         PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>     Capabilities: [40] Express (v1) PCI/PCI-X Bridge, MSI 00
>         DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s 
> <64ns, L1 <1us
>             ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal+ 
> Unsupported-
>             RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
>             MaxPayload 128 bytes, MaxReadReq 512 bytes
>         DevSta:    CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- 
> TransPend-
>         LnkCap:    Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, 
> Latency L0 <4us, L1 <16us
>             ClockPM- Suprise- LLActRep- BwNot-
>         LnkCtl:    ASPM Disabled; Disabled- Retrain- CommClk-
>             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>         LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- 
> DLActive- BWMgmt- ABWMgmt-
>     Capabilities: [54] PCI-X bridge device
>         Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
>         Status: Dev=2b:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
>         Upstream: Capacity=32 CommitmentLimit=32
>         Downstream: Capacity=16 CommitmentLimit=16
>     Capabilities: [64] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA 
> PME(D0+,D1+,D2-,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>         Bridge: PM- B3+
>     Capabilities: [100] Advanced Error Reporting <?>
>     Kernel modules: shpchp
> 00: 33 10 25 01 07 00 10 00 06 00 04 06 10 00 81 00
> 10: 00 00 00 00 00 00 00 00 2b 2c 2c 20 f1 01 20 24
> 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 02 00
> 40: 10 54 71 00 01 00 00 00 04 20 0a 00 81 6c 02 00
> 50: 00 00 41 00 07 64 c3 00 00 2b 00 00 20 00 20 00
> 60: 10 00 10 00 01 00 42 da 00 00 c0 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 0c 00 19 1f 00 00 00 00
> 90: 13 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:2b:00.1 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express 
> - PCI/PCI-X Bridge [1033:0125] (rev 06)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0, Cache Line Size: 64 bytes
>     Region 0: Memory at fcd00000 (64-bit, non-prefetchable) [size=128]
>     Bus: primary=2b, secondary=2d, subordinate=2d, sec-latency=32
>     I/O behind bridge: 0000f000-00000fff
>     Memory behind bridge: fff00000-000fffff
>     Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
>     Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>     BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
>         PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>     Capabilities: [40] Express (v1) PCI/PCI-X Bridge, MSI 00
>         DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s 
> <64ns, L1 <1us
>             ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal+ 
> Unsupported-
>             RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
>             MaxPayload 128 bytes, MaxReadReq 512 bytes
>         DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>         LnkCap:    Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, 
> Latency L0 <4us, L1 <16us
>             ClockPM- Suprise- LLActRep- BwNot-
>         LnkCtl:    ASPM Disabled; Disabled- Retrain- CommClk-
>             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>         LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- 
> DLActive- BWMgmt- ABWMgmt-
>     Capabilities: [54] PCI-X bridge device
>         Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
>         Status: Dev=2b:00.1 64bit- 133MHz- SCD- USC- SCO- SRD-
>         Upstream: Capacity=32 CommitmentLimit=32
>         Downstream: Capacity=16 CommitmentLimit=16
>     Capabilities: [64] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA 
> PME(D0+,D1+,D2-,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>         Bridge: PM- B3+
>     Capabilities: [6c] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/0 Enable-
>         Address: 0000000000000000  Data: 0000
>     Capabilities: [7c] Hot-plug capable
>     Capabilities: [100] Advanced Error Reporting <?>
>     Kernel modules: shpchp
> 00: 33 10 25 01 07 00 10 00 06 00 04 06 10 00 81 00
> 10: 04 00 d0 fc 00 00 00 00 2b 2d 2d 20 f1 01 20 24
> 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 01 02 00
> 40: 10 54 71 00 01 00 00 00 04 20 00 00 81 6c 02 00
> 50: 00 00 41 00 07 64 03 00 01 2b 00 00 20 00 20 00
> 60: 10 00 10 00 01 6c 42 da 00 00 c0 00 05 7c 80 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 13 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0001:40:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory 
> Controller [10de:0369] (rev a2)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0
>     Capabilities: [44] HyperTransport: Slave or Primary Interface
>         Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
>         Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- 
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
>         Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- 
> LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
>         Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ 
> <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
>         Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit 
> DwFcInEn- LWO=8bit DwFcOutEn-
>         Revision ID: 1.03
>         Link Frequency 0: 1.0GHz
>         Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 
> 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
>         Link Frequency 1: 200MHz
>         Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
>         Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 
> 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
>         Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- 
> SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
>         Prefetchable memory behind bridge Upper: 00-00
>         Bus Number: 00
>     Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed-
>         Mapping Address Base: 00000000fee00000
> 00: de 10 69 03 06 01 b0 00 a2 00 00 05 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 00 00 00
> 40: 3c 10 fe 12 08 dc e0 01 22 00 11 11 d0 00 00 00
> 50: 23 06 7f 00 03 00 00 00 00 00 03 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 38 0a 00
> 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00
> 80: 23 99 88 00 fa 00 64 0e 02 00 00 00 7f 00 00 00
> 90: 78 00 40 90 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 80 00 0f 0f
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8
> e0: 00 00 e0 fe 00 00 00 00 00 00 80 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0001:40:01.0 RAM memory [0500]: nVidia Corporation MCP55 LPC Bridge 
> [10de:0361] (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0
>     Region 1: Memory at fd000000 (32-bit, non-prefetchable) [size=4K]
> 00: de 10 61 03 0f 00 a0 00 a3 00 00 05 00 00 80 00
> 10: 00 00 00 00 00 00 00 fd 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
> 40: 3c 10 fe 12 00 00 00 00 fa 3e ff 00 fa 3e ff 00
> 50: fa 3e ff 00 00 5a 62 02 00 00 00 01 00 00 ff ff
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 f9 ff
> 70: 10 00 ff ff c7 80 00 00 00 00 46 20 00 00 00 c0
> 80: 00 00 00 00 00 00 00 00 ff 00 00 01 ff 00 00 00
> 90: ff 7f 00 00 00 00 00 00 21 47 95 86 ef cd ab 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
>
> 0001:40:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] 
> (rev a3)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Interrupt: pin A routed to IRQ 255
>     Region 4: I/O ports at 2000 [size=64]
>     Region 5: I/O ports at 2040 [size=64]
>     Capabilities: [44] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Kernel driver in use: nForce2_smbus
>     Kernel modules: i2c-nforce2
> 00: de 10 68 03 01 00 b0 00 a3 00 05 0c 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 20 00 00 41 20 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 01 00 00
> 40: 3c 10 fe 12 01 00 02 c0 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 e8 00 00 01 e9 00 00 01 ea 00 00 00 00 00 00
> 70: 01 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: d4 30 80 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: e6 16 05 00 b5 03 00 07 80 ff 57 00 61 44 44 11
> f0: 5a ff 5f 3f 00 00 00 c0 10 00 00 00 00 00 00 00
>
> 0001:40:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express 
> bridge [10de:0378] (rev a3)
>     Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR+ FastB2B- DisINTx+
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Latency: 0, Cache Line Size: 64 bytes
>     Bus: primary=40, secondary=6b, subordinate=6b, sec-latency=0
>     I/O behind bridge: 00001000-00001fff
>     Memory behind bridge: fcf00000-fcffffff
>     Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
>     Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort+ <SERR- <PERR-
>     BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
>         PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
>     Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
>     Capabilities: [48] Power Management version 2
>         Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/1 Enable+
>         Address: 00000000feeff00c  Data: 4159
>     Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
>         Mapping Address Base: 00000000fee00000
>     Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
>         DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s 
> <64ns, L1 <1us
>             ExtTag- RBE+ FLReset-
>         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>             RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>             MaxPayload 128 bytes, MaxReadReq 512 bytes
>         DevSta:    CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>         LnkCap:    Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, 
> Latency L0 <512ns, L1 <4us
>             ClockPM- Suprise- LLActRep+ BwNot-
>         LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
>             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>         LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ 
> DLActive+ BWMgmt- ABWMgmt-
>         SltCap:    AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
> Surpise-
>             Slot #  0, PowerLimit 0.000000; Interlock- NoCompl-
>         SltCtl:    Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- 
> HPIrq- LinkChg-
>             Control: AttnInd Off, PwrInd On, Power- Interlock-
>         SltSta:    Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
> Interlock-
>             Changed: MRL- PresDet+ LinkState+
>         RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
> CRSVisible-
>         RootCap: CRSVisible-
>         RootSta: PME ReqID 0000, PMEStatus- PMEPending-
>     Capabilities: [100] Virtual Channel <?>
>     Capabilities: [160] Advanced Error Reporting <?>
>     Kernel driver in use: pcieport-driver
>     Kernel modules: shpchp
> 00: de 10 78 03 07 05 10 00 a3 00 04 06 10 00 01 00
> 10: 00 00 00 00 00 00 00 00 40 6b 6b 00 11 11 00 20
> 20: f0 fc f0 fc f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 02 00
> 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00
> 50: 05 60 83 00 0c f0 ef fe 00 00 00 00 59 41 00 00
> 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 10 00 41 01 01 80 00 00 10 28 01 00 41 3c 11 02
> 90: 00 00 41 30 00 00 00 00 c0 01 48 01 04 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0001:6b:00.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 
> SAS1068E PCI-Express Fusion-MPT SAS [1000:0058] (rev 08)
>     Subsystem: Hewlett-Packard Company Device [103c:12fe]
>     Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- 
> ParErr- Stepping- SERR- FastB2B- DisINTx-
>     Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- 
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>     Interrupt: pin A routed to IRQ 43
>     Region 0: I/O ports at 1000 [disabled] [size=256]
>     Region 1: Memory at <unassigned> (64-bit, non-prefetchable) [disabled]
>     Region 3: Memory at <unassigned> (64-bit, non-prefetchable) [disabled]
>     [virtual] Expansion ROM at fcf00000 [disabled] [size=1M]
>     Capabilities: [50] Power Management version 2
>         Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
>         Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>     Capabilities: [68] Express (v1) Endpoint, MSI 00
>         DevCap:    MaxPayload 4096 bytes, PhantFunc 0, Latency L0s 
> <64ns, L1 <1us
>             ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
>         DevCtl:    Report errors: Correctable- Non-Fatal- Fatal- 
> Unsupported-
>             RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
>             MaxPayload 128 bytes, MaxReadReq 512 bytes
>         DevSta:    CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
> TransPend-
>         LnkCap:    Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, 
> Latency L0 <64ns, L1 <1us
>             ClockPM- Suprise- LLActRep- BwNot-
>         LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
>             ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
>         LnkSta:    Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- 
> DLActive- BWMgmt- ABWMgmt-
>     Capabilities: [98] Message Signalled Interrupts: Mask- 64bit+ 
> Queue=0/0 Enable-
>         Address: 0000000000000000  Data: 0000
>     Capabilities: [b0] MSI-X: Enable- Mask- TabSize=1
>         Vector table: BAR=1 offset=00002000
>         PBA: BAR=1 offset=00003000
>     Capabilities: [100] Advanced Error Reporting <?>
>     Kernel modules: mptsas
> 00: 00 10 58 00 00 00 10 00 08 00 00 01 00 00 00 00
> 10: 01 00 00 00 04 00 00 00 00 00 00 00 04 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 3c 10 fe 12
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 00 01 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 01 68 02 06 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 10 98 01 00 25 00 00 00
> 70: 10 28 00 00 81 0c 00 00 00 00 41 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 05 b0 80 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 11 00 00 00 01 20 00 00 01 30 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
>
>
>
>
> ------------------------------------------------------------------------
> Windows 7 : Trouvez le PC qui vous convient! Découvrez notre offre ! 
> <http://clk.atdmt.com/FRM/go/181574577/direct/01/>
>
>
> _______________________________________________
> flashrom mailing list
> flashrom at flashrom.org
> http://www.flashrom.org/mailman/listinfo/flashrom
>    

-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: dump.txt
URL: <http://www.flashrom.org/pipermail/flashrom/attachments/20100120/ebd430d2/attachment.txt>
-------------- next part --------------
An embedded and charset-unspecified text was scrubbed...
Name: superiotool.txt
URL: <http://www.flashrom.org/pipermail/flashrom/attachments/20100120/ebd430d2/attachment-0001.txt>