[coreboot-gerrit] Change in ...coreboot[master]: qcs405: Add blsp uart driver
Name of user not set (Code Review)
gerrit at coreboot.org
Fri Nov 30 11:14:06 CET 2018
nsekar at codeaurora.org has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/29964
Change subject: qcs405: Add blsp uart driver
......................................................................
qcs405: Add blsp uart driver
Change-Id: Id9626c68eadead8b8ec5ffbc08cab7b0ec36478f
Signed-off-by: Nitheesh Sekar <nsekar at codeaurora.org>
Signed-off-by: Sricharan R <sricharan at codeaurora.org>
Signed-off-by: Prudhvi Yarlagadda<pyarlaga at codeaurora.org>
Signed-off-by: Sricharan R <sricharan at codeaurora.org>
---
M src/soc/qualcomm/qcs405/Makefile.inc
A src/soc/qualcomm/qcs405/include/soc/blsp.h
A src/soc/qualcomm/qcs405/include/soc/cdp.h
A src/soc/qualcomm/qcs405/include/soc/iomap.h
A src/soc/qualcomm/qcs405/include/soc/ipq_uart.h
A src/soc/qualcomm/qcs405/uart.c
6 files changed, 976 insertions(+), 4 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/64/29964/1
diff --git a/src/soc/qualcomm/qcs405/Makefile.inc b/src/soc/qualcomm/qcs405/Makefile.inc
index 58a62fa..57d59f8 100644
--- a/src/soc/qualcomm/qcs405/Makefile.inc
+++ b/src/soc/qualcomm/qcs405/Makefile.inc
@@ -8,14 +8,14 @@
bootblock-y += timer.c
bootblock-y += gpio.c
bootblock-y += clock.c
-bootblock-$(CONFIG_DRIVERS_UART) += uart_bitbang.c
+bootblock-$(CONFIG_DRIVERS_UART) += uart.c
bootblock-$(CONFIG_QC_SOC_SIMULATE) += flash_controller.c
################################################################################
verstage-y += spi.c
verstage-y += timer.c
verstage-y += gpio.c
-verstage-$(CONFIG_DRIVERS_UART) += uart_bitbang.c
+verstage-$(CONFIG_DRIVERS_UART) += uart.c
verstage-$(CONFIG_QC_SOC_SIMULATE) += flash_controller.c
################################################################################
@@ -25,7 +25,7 @@
romstage-y += gpio.c
romstage-y += clock.c
romstage-y += mmu.c
-romstage-$(CONFIG_DRIVERS_UART) += uart_bitbang.c
+romstage-$(CONFIG_DRIVERS_UART) += uart.c
romstage-$(CONFIG_QC_SOC_SIMULATE) += flash_controller.c
################################################################################
@@ -35,7 +35,7 @@
ramstage-y += timer.c
ramstage-y += gpio.c
ramstage-y += clock.c
-ramstage-$(CONFIG_DRIVERS_UART) += uart_bitbang.c
+ramstage-$(CONFIG_DRIVERS_UART) += uart.c
ramstage-$(CONFIG_QC_SOC_SIMULATE) += flash_controller.c
################################################################################
diff --git a/src/soc/qualcomm/qcs405/include/soc/blsp.h b/src/soc/qualcomm/qcs405/include/soc/blsp.h
new file mode 100644
index 0000000..ce74e56
--- /dev/null
+++ b/src/soc/qualcomm/qcs405/include/soc/blsp.h
@@ -0,0 +1,60 @@
+/*
+ * Copyright (c) 2011-2012 The Linux Foundation. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of The Linux Foundation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+
+#ifndef __BLSP_H_
+#define __BLSP_H_
+
+typedef enum {
+ BLSP_QUP_ID_0,
+ BLSP_QUP_ID_1,
+ BLSP_QUP_ID_2,
+ BLSP_QUP_ID_3,
+} blsp_qup_id_t;
+
+typedef enum {
+ BLSP_SUCCESS = 0,
+ BLSP_ID_ERROR,
+ BLSP_ERROR,
+ BLSP_UNSUPPORTED
+} blsp_return_t;
+
+typedef enum {
+ BLSP_PROTO_I2C_UIM = 1,
+ BLSP_PROTO_I2C_ONLY,
+ BLSP_PROTO_SPI_ONLY,
+ BLSP_PROTO_UART_FLOW_CTL,
+ BLSP_PROTO_UIM,
+ BLSP_PROTO_I2C_UART,
+} blsp_protocol_t;
+
+blsp_return_t blsp_i2c_init(blsp_qup_id_t id);
+int blsp_i2c_init_board(blsp_qup_id_t id);
+
+#endif
diff --git a/src/soc/qualcomm/qcs405/include/soc/cdp.h b/src/soc/qualcomm/qcs405/include/soc/cdp.h
new file mode 100644
index 0000000..ca9e996
--- /dev/null
+++ b/src/soc/qualcomm/qcs405/include/soc/cdp.h
@@ -0,0 +1,175 @@
+/*
+ * Copyright (c) 2012 The Linux Foundation. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of The Linux Foundation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+
+#ifndef _IPQ40XX_CDP_H_
+#define _IPQ40XX_CDP_H_
+
+#include <types.h>
+
+unsigned smem_get_board_machtype(void);
+
+typedef enum {
+ PHY_INTERFACE_MODE_MII,
+ PHY_INTERFACE_MODE_GMII,
+ PHY_INTERFACE_MODE_SGMII,
+ PHY_INTERFACE_MODE_QSGMII,
+ PHY_INTERFACE_MODE_TBI,
+ PHY_INTERFACE_MODE_RMII,
+ PHY_INTERFACE_MODE_RGMII,
+ PHY_INTERFACE_MODE_RGMII_ID,
+ PHY_INTERFACE_MODE_RGMII_RXID,
+ PHY_INTERFACE_MODE_RGMII_TXID,
+ PHY_INTERFACE_MODE_RTBI,
+ PHY_INTERFACE_MODE_XGMII,
+ PHY_INTERFACE_MODE_NONE /* Must be last */
+} phy_interface_t;
+
+typedef struct {
+ gpio_t gpio;
+ unsigned int func;
+ unsigned int dir;
+ unsigned int pull;
+ unsigned int drvstr;
+ unsigned int enable;
+} gpio_func_data_t;
+
+typedef struct {
+ unsigned int m_value;
+ unsigned int n_value;
+ unsigned int d_value;
+} uart_clk_mnd_t;
+
+/* SPI Mode */
+
+typedef enum {
+ NOR_SPI_MODE_0,
+ NOR_SPI_MODE_1,
+ NOR_SPI_MODE_2,
+ NOR_SPI_MODE_3,
+} spi_mode;
+
+/* SPI GSBI Bus number */
+
+typedef enum {
+ GSBI_BUS_5 = 0,
+ GSBI_BUS_6,
+ GSBI_BUS_7,
+} spi_gsbi_bus_num;
+
+/* SPI Chip selects */
+
+typedef enum {
+ SPI_CS_0 ,
+ SPI_CS_1,
+ SPI_CS_2,
+ SPI_CS_3,
+} spi_cs;
+
+/* Flash Types */
+
+typedef enum {
+ ONLY_NAND,
+ ONLY_NOR,
+ NAND_NOR,
+ NOR_MMC,
+} flash_desc;
+
+#define NO_OF_DBG_UART_GPIOS 2
+
+#define SPI_NOR_FLASH_VENDOR_MICRON 0x1
+#define SPI_NOR_FLASH_VENDOR_SPANSION 0x2
+
+/* SPI parameters */
+
+typedef struct {
+ spi_mode mode;
+ spi_gsbi_bus_num bus_number;
+ spi_cs chip_select;
+ int vendor;
+} spinorflash_params_t;
+
+typedef struct {
+ unsigned count;
+ uint8_t addr[7];
+} ipq_gmac_phy_addr_t;
+
+typedef struct {
+ unsigned base;
+ int unit;
+ unsigned is_macsec;
+ unsigned mac_pwr0;
+ unsigned mac_pwr1;
+ unsigned mac_conn_to_phy;
+ phy_interface_t phy;
+ ipq_gmac_phy_addr_t phy_addr;
+} ipq_gmac_board_cfg_t;
+
+#define IPQ_GMAC_NMACS 4
+
+enum gale_board_id {
+ BOARD_ID_GALE_PROTO = 0,
+ BOARD_ID_GALE_EVT = 1,
+ BOARD_ID_GALE_EVT2_0 = 2,
+ BOARD_ID_GALE_EVT2_1 = 6,
+ BOARD_ID_GALE_EVT3 = 5,
+};
+
+/* Board specific parameters */
+typedef struct {
+#if 0
+ unsigned int gmac_gpio_count;
+ gpio_func_data_t *gmac_gpio;
+ ipq_gmac_board_cfg_t gmac_cfg[IPQ_GMAC_NMACS];
+ flash_desc flashdesc;
+ spinorflash_params_t flash_param;
+#endif
+} __packed board_ipq40xx_params_t;
+
+extern board_ipq40xx_params_t *gboard_param;
+
+#if 0
+static inline int gmac_cfg_is_valid(ipq_gmac_board_cfg_t *cfg)
+{
+ /*
+ * 'cfg' is valid if and only if
+ * unit number is non-negative and less than IPQ_GMAC_NMACS.
+ * 'cfg' pointer lies within the array range of
+ * board_ipq40xx_params_t->gmac_cfg[]
+ */
+ return ((cfg >= &gboard_param->gmac_cfg[0]) &&
+ (cfg < &gboard_param->gmac_cfg[IPQ_GMAC_NMACS]) &&
+ (cfg->unit >= 0) && (cfg->unit < IPQ_GMAC_NMACS));
+}
+#endif
+
+unsigned int get_board_index(unsigned machid);
+void ipq_configure_gpio(const gpio_func_data_t *gpio, unsigned count);
+
+#endif /* _IPQ40XX_CDP_H_ */
diff --git a/src/soc/qualcomm/qcs405/include/soc/iomap.h b/src/soc/qualcomm/qcs405/include/soc/iomap.h
new file mode 100644
index 0000000..2a7a148
--- /dev/null
+++ b/src/soc/qualcomm/qcs405/include/soc/iomap.h
@@ -0,0 +1,155 @@
+/*
+ * Copyright (c) 2012 - 2013, 2015 The Linux Foundation. All rights reserved.
+ *
+ * Copyright (c) 2008, Google Inc.
+ * All rights reserved.
+ *
+ * Copyright (c) 2009-2012, Code Aurora Forum. All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions
+ * are met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in
+ * the documentation and/or other materials provided with the
+ * distribution.
+ * * Neither the name of Google, Inc. nor the names of its contributors
+ * may be used to endorse or promote products derived from this
+ * software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
+ * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
+ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
+ * FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
+ * COPYRIGHT OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
+ * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
+ * OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED
+ * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
+ * OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+ * SUCH DAMAGE.
+ */
+
+#ifndef __SOC_QUALCOMM_IPQ40XX_IOMAP_H_
+#define __SOC_QUALCOMM_IPQ40XX_IOMAP_H_
+
+#include <arch/io.h>
+#include <soc/cdp.h>
+#include <soc/blsp.h>
+
+/* Typecast to allow integers being passed as address
+ This needs to be included because vendor code is not compliant with our
+ macros for read/write. Hence, special macros for readl_i and writel_i are
+ included to do this in one place for all occurrences in vendor code
+ */
+#define readl_i(a) read32((const void *)(a))
+#define writel_i(v,a) write32((void *)a, v)
+#define clrsetbits_le32_i(addr, clear, set) \
+ clrsetbits_le32(((void *)(addr)), (clear), (set))
+
+#define GCC_CLK_CTL_REG ((void *)0x01800000u)
+#define MSM_CLK_CTL_BASE GCC_CLK_CTL_REG
+#define GCC_CLK_BRANCH_ENA (GCC_CLK_CTL_REG + 0x6000)
+#define IMEM_AXI (1 << 17)
+#define SYS_NOC_APSS_AHB (1 << 16)
+#define BIMC_AXI_M0 (1 << 15)
+#define APSS_AHB (1 << 14)
+#define APSS_AXI (1 << 13)
+#define MPM_AHB (1 << 12)
+#define GMEM_SYS_NOC_AXI (1 << 11)
+#define BLSP1_AHB (1 << 10)
+#define BLSP1_SLEEP (1 << 9)
+#define PRNG_AHB (1 << 8)
+#define BOOT_ROM_AHB (1 << 7)
+#define MSG_RAM_AHB (1 << 6)
+#define TLMM_AHB (1 << 5)
+#define TLMM (1 << 4)
+#define SPMI_PCNOC_AHB (1 << 3)
+#define CRYPTO (1 << 2)
+#define CRYPTO_AXI (1 << 1)
+#define CRYPTO_AHB (1 << 0)
+
+#define GCC_BLSP1_QUP1_I2C_APPS_CBCR (MSM_CLK_CTL_BASE + 0x2008)
+#define GCC_BLSP1_QUP1_I2C_APPS_CMD_RCGR (MSM_CLK_CTL_BASE + 0x200c)
+#define GCC_BLSP1_QUP1_I2C_APPS_CFG_RCGR (MSM_CLK_CTL_BASE + 0x2010)
+#define GCC_BLSP1_QUP2_I2C_APPS_CBCR (MSM_CLK_CTL_BASE + 0x3010)
+#define GCC_BLSP1_QUP2_I2C_APPS_CMD_RCGR (MSM_CLK_CTL_BASE + 0x3000)
+#define GCC_BLSP1_QUP2_I2C_APPS_CFG_RCGR (MSM_CLK_CTL_BASE + 0x3004)
+
+#define GCNT_GLOBAL_CTRL_BASE ((void *)0x004a0000u)
+#define GCNT_CNTCR (GCNT_GLOBAL_CTRL_BASE + 0x1000)
+#define GCNT_GLB_CNTCV_LO (GCNT_GLOBAL_CTRL_BASE + 0x1008)
+#define GCNT_GLB_CNTCV_HI (GCNT_GLOBAL_CTRL_BASE + 0x100c)
+#define GCNT_CNTCV_LO (GCNT_GLOBAL_CTRL_BASE + 0x2000)
+#define GCNT_CNTCV_HI (GCNT_GLOBAL_CTRL_BASE + 0x2004)
+
+#define GCNT_PSHOLD ((void *)0x004AB000u)
+
+/* RPM interface constants */
+#define RPM_INT ((void *)0x63020)
+#define RPM_INT_ACK ((void *)0x63060)
+#define RPM_SIGNAL_COOKIE ((void *)0x47C20)
+#define RPM_SIGNAL_ENTRY ((void *)0x47C24)
+#define RPM_FW_MAGIC_NUM 0x4D505242
+
+#define TLMM_BASE_ADDR ((void *)0x01000000)
+#define GPIO_CONFIG_ADDR(x) (TLMM_BASE_ADDR + 0x1000 * (x))
+#define GPIO_IN_OUT_ADDR(x) (GPIO_CONFIG_ADDR(x) + 4)
+
+/* Yes, this is not a typo... host2 is actually mapped before host1. */
+#define USB_HOST2_XHCI_BASE 0x10000000
+#define USB_HOST2_DWC3_BASE 0x1000C100
+#define USB_HOST2_PHY_BASE 0x100F8800
+#define USB_HOST1_XHCI_BASE 0x11000000
+#define USB_HOST1_DWC3_BASE 0x1100C100
+#define USB_HOST1_PHY_BASE 0x110F8800
+
+#define UART1_DM_BASE ((void *)0x078af000)
+#define UART2_DM_BASE ((void *)0x078B1000)
+
+enum {
+ BLSP1_UART1,
+ BLSP1_UART2,
+};
+
+#define GCC_BLSP1_UART_BCR_BASE (GCC_CLK_CTL_REG + 0x2038)
+#define GCC_BLSP1_UART_BCR(x) (GCC_BLSP1_UART_BCR_BASE + (x) * 0xff0)
+#define GCC_BLSP1_UART_APPS_CBCR(x) (GCC_BLSP1_UART_BCR(x) + 4)
+#define GCC_BLSP1_UART_APPS_CMD_RCGR(x) (GCC_BLSP1_UART_APPS_CBCR(x) + 8)
+#define GCC_BLSP1_UART_APPS_CFG_RCGR(x) (GCC_BLSP1_UART_APPS_CMD_RCGR(x) + 4)
+#define GCC_BLSP1_UART_APPS_M(x) (GCC_BLSP1_UART_APPS_CFG_RCGR(x) + 4)
+#define GCC_BLSP1_UART_APPS_N(x) (GCC_BLSP1_UART_APPS_M(x) + 4)
+#define GCC_BLSP1_UART_APPS_D(x) (GCC_BLSP1_UART_APPS_N(x) + 4)
+#define GCC_BLSP1_UART_MISC(x) (GCC_BLSP1_UART_APPS_D(x) + 4)
+
+#define BLSP1_QUP0_BASE ((void *)0x078B5000)
+#define BLSP1_QUP1_BASE ((void *)0x078B6000)
+#define BLSP1_QUP2_BASE ((void *)0x078B7000)
+#define BLSP1_QUP3_BASE ((void *)0x078B8000)
+
+#define TCSR_BOOT_MISC_DETECT ((void *)0x0193D100)
+#define TCSR_RESET_DEBUG_SW_ENTRY ((void *)0x01940000)
+
+static inline void *blsp_qup_base(blsp_qup_id_t id)
+{
+ switch (id) {
+ case BLSP_QUP_ID_0: return BLSP1_QUP0_BASE;
+ case BLSP_QUP_ID_1: return BLSP1_QUP1_BASE;
+ case BLSP_QUP_ID_2: return BLSP1_QUP2_BASE;
+ case BLSP_QUP_ID_3: return BLSP1_QUP3_BASE;
+ }
+ return NULL;
+}
+
+#define BLSP_MINI_CORE_SHIFT 8
+#define BLSP_MINI_CORE_I2C (0x2u << BLSP_MINI_CORE_SHIFT)
+#define BLSP_MINI_CORE_MASK (0xfu << BLSP_MINI_CORE_SHIFT)
+
+#define ETIMEDOUT -10
+#define EINVAL -11
+#define EIO -12
+
+#endif // __SOC_QUALCOMM_IPQ40XX_IOMAP_H_
diff --git a/src/soc/qualcomm/qcs405/include/soc/ipq_uart.h b/src/soc/qualcomm/qcs405/include/soc/ipq_uart.h
new file mode 100644
index 0000000..8cb0f25
--- /dev/null
+++ b/src/soc/qualcomm/qcs405/include/soc/ipq_uart.h
@@ -0,0 +1,273 @@
+/*
+ * Copyright (c) 2012 The Linux Foundation. All rights reserved.*
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of The Linux Foundation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#ifndef __UART_DM_H__
+#define __UART_DM_H__
+
+#define PERIPH_BLK_BLSP 1
+
+#define MSM_BOOT_UART_DM_EXTR_BITS(value, start_pos, end_pos) \
+ ((value << (32 - end_pos)) >> (32 - (end_pos - start_pos)))
+
+extern void __udelay(unsigned long usec);
+
+
+enum MSM_BOOT_UART_DM_PARITY_MODE {
+ MSM_BOOT_UART_DM_NO_PARITY,
+ MSM_BOOT_UART_DM_ODD_PARITY,
+ MSM_BOOT_UART_DM_EVEN_PARITY,
+ MSM_BOOT_UART_DM_SPACE_PARITY
+};
+
+/* UART Stop Bit Length */
+enum MSM_BOOT_UART_DM_STOP_BIT_LEN {
+ MSM_BOOT_UART_DM_SBL_9_16,
+ MSM_BOOT_UART_DM_SBL_1,
+ MSM_BOOT_UART_DM_SBL_1_9_16,
+ MSM_BOOT_UART_DM_SBL_2
+};
+
+/* UART Bits per Char */
+enum MSM_BOOT_UART_DM_BITS_PER_CHAR {
+ MSM_BOOT_UART_DM_5_BPS,
+ MSM_BOOT_UART_DM_6_BPS,
+ MSM_BOOT_UART_DM_7_BPS,
+ MSM_BOOT_UART_DM_8_BPS
+};
+
+/* 8-N-1 Configuration */
+#define MSM_BOOT_UART_DM_8_N_1_MODE (MSM_BOOT_UART_DM_NO_PARITY | \
+ (MSM_BOOT_UART_DM_SBL_1 << 2) | \
+ (MSM_BOOT_UART_DM_8_BPS << 4))
+
+/* UART_DM Registers */
+
+/* UART Operational Mode Register */
+#define MSM_BOOT_UART_DM_MR1(base) ((base) + 0x00)
+#define MSM_BOOT_UART_DM_MR2(base) ((base) + 0x04)
+#define MSM_BOOT_UART_DM_RXBRK_ZERO_CHAR_OFF (1 << 8)
+#define MSM_BOOT_UART_DM_LOOPBACK (1 << 7)
+
+/* UART Clock Selection Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_CSR(base) ((base) + 0xA0)
+#else
+#define MSM_BOOT_UART_DM_CSR(base) ((base) + 0x08)
+#endif
+
+/* UART DM TX FIFO Registers - 4 */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x100+(4*(x)))
+#else
+#define MSM_BOOT_UART_DM_TF(base, x) ((base) + 0x70+(4*(x)))
+#endif
+
+/* UART Command Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_CR(base) ((base) + 0xA8)
+#else
+#define MSM_BOOT_UART_DM_CR(base) ((base) + 0x10)
+#endif
+#define MSM_BOOT_UART_DM_CR_RX_ENABLE (1 << 0)
+#define MSM_BOOT_UART_DM_CR_RX_DISABLE (1 << 1)
+#define MSM_BOOT_UART_DM_CR_TX_ENABLE (1 << 2)
+#define MSM_BOOT_UART_DM_CR_TX_DISABLE (1 << 3)
+
+/* UART Channel Command */
+#define MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x) ((x & 0x0f) << 4)
+#define MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x) ((x >> 4) << 11)
+#define MSM_BOOT_UART_DM_CR_CH_CMD(x) \
+ (MSM_BOOT_UART_DM_CR_CH_CMD_LSB(x) | MSM_BOOT_UART_DM_CR_CH_CMD_MSB(x))
+#define MSM_BOOT_UART_DM_CMD_NULL MSM_BOOT_UART_DM_CR_CH_CMD(0)
+#define MSM_BOOT_UART_DM_CMD_RESET_RX MSM_BOOT_UART_DM_CR_CH_CMD(1)
+#define MSM_BOOT_UART_DM_CMD_RESET_TX MSM_BOOT_UART_DM_CR_CH_CMD(2)
+#define MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT MSM_BOOT_UART_DM_CR_CH_CMD(3)
+#define MSM_BOOT_UART_DM_CMD_RES_BRK_CHG_INT MSM_BOOT_UART_DM_CR_CH_CMD(4)
+#define MSM_BOOT_UART_DM_CMD_START_BRK MSM_BOOT_UART_DM_CR_CH_CMD(5)
+#define MSM_BOOT_UART_DM_CMD_STOP_BRK MSM_BOOT_UART_DM_CR_CH_CMD(6)
+#define MSM_BOOT_UART_DM_CMD_RES_CTS_N MSM_BOOT_UART_DM_CR_CH_CMD(7)
+#define MSM_BOOT_UART_DM_CMD_RES_STALE_INT MSM_BOOT_UART_DM_CR_CH_CMD(8)
+#define MSM_BOOT_UART_DM_CMD_PACKET_MODE MSM_BOOT_UART_DM_CR_CH_CMD(9)
+#define MSM_BOOT_UART_DM_CMD_MODE_RESET MSM_BOOT_UART_DM_CR_CH_CMD(C)
+#define MSM_BOOT_UART_DM_CMD_SET_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(D)
+#define MSM_BOOT_UART_DM_CMD_RES_RFR_N MSM_BOOT_UART_DM_CR_CH_CMD(E)
+#define MSM_BOOT_UART_DM_CMD_RES_TX_ERR MSM_BOOT_UART_DM_CR_CH_CMD(10)
+#define MSM_BOOT_UART_DM_CMD_CLR_TX_DONE MSM_BOOT_UART_DM_CR_CH_CMD(11)
+#define MSM_BOOT_UART_DM_CMD_RES_BRKSTRT_INT MSM_BOOT_UART_DM_CR_CH_CMD(12)
+#define MSM_BOOT_UART_DM_CMD_RES_BRKEND_INT MSM_BOOT_UART_DM_CR_CH_CMD(13)
+#define MSM_BOOT_UART_DM_CMD_RES_PER_FRM_INT MSM_BOOT_UART_DM_CR_CH_CMD(14)
+
+/*UART General Command */
+#define MSM_BOOT_UART_DM_CR_GENERAL_CMD(x) ((x) << 8)
+
+#define MSM_BOOT_UART_DM_GCMD_NULL MSM_BOOT_UART_DM_CR_GENERAL_CMD(0)
+#define MSM_BOOT_UART_DM_GCMD_CR_PROT_EN MSM_BOOT_UART_DM_CR_GENERAL_CMD(1)
+#define MSM_BOOT_UART_DM_GCMD_CR_PROT_DIS MSM_BOOT_UART_DM_CR_GENERAL_CMD(2)
+#define MSM_BOOT_UART_DM_GCMD_RES_TX_RDY_INT MSM_BOOT_UART_DM_CR_GENERAL_CMD(3)
+#define MSM_BOOT_UART_DM_GCMD_SW_FORCE_STALE MSM_BOOT_UART_DM_CR_GENERAL_CMD(4)
+#define MSM_BOOT_UART_DM_GCMD_ENA_STALE_EVT MSM_BOOT_UART_DM_CR_GENERAL_CMD(5)
+#define MSM_BOOT_UART_DM_GCMD_DIS_STALE_EVT MSM_BOOT_UART_DM_CR_GENERAL_CMD(6)
+
+/* UART Interrupt Mask Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_IMR(base) ((base) + 0xB0)
+#else
+#define MSM_BOOT_UART_DM_IMR(base) ((base) + 0x14)
+#endif
+
+#define MSM_BOOT_UART_DM_TXLEV (1 << 0)
+#define MSM_BOOT_UART_DM_RXHUNT (1 << 1)
+#define MSM_BOOT_UART_DM_RXBRK_CHNG (1 << 2)
+#define MSM_BOOT_UART_DM_RXSTALE (1 << 3)
+#define MSM_BOOT_UART_DM_RXLEV (1 << 4)
+#define MSM_BOOT_UART_DM_DELTA_CTS (1 << 5)
+#define MSM_BOOT_UART_DM_CURRENT_CTS (1 << 6)
+#define MSM_BOOT_UART_DM_TX_READY (1 << 7)
+#define MSM_BOOT_UART_DM_TX_ERROR (1 << 8)
+#define MSM_BOOT_UART_DM_TX_DONE (1 << 9)
+#define MSM_BOOT_UART_DM_RXBREAK_START (1 << 10)
+#define MSM_BOOT_UART_DM_RXBREAK_END (1 << 11)
+#define MSM_BOOT_UART_DM_PAR_FRAME_ERR_IRQ (1 << 12)
+
+#define MSM_BOOT_UART_DM_IMR_ENABLED (MSM_BOOT_UART_DM_TX_READY | \
+ MSM_BOOT_UART_DM_TXLEV | \
+ MSM_BOOT_UART_DM_RXSTALE)
+
+/* UART Interrupt Programming Register */
+#define MSM_BOOT_UART_DM_IPR(base) ((base) + 0x18)
+#define MSM_BOOT_UART_DM_STALE_TIMEOUT_LSB 0x0f
+#define MSM_BOOT_UART_DM_STALE_TIMEOUT_MSB 0 /* Not used currently */
+
+/* UART Transmit/Receive FIFO Watermark Register */
+#define MSM_BOOT_UART_DM_TFWR(base) ((base) + 0x1C)
+/* Interrupt is generated when FIFO level is less than or equal to this value */
+#define MSM_BOOT_UART_DM_TFW_VALUE 0
+
+#define MSM_BOOT_UART_DM_RFWR(base) ((base) + 0x20)
+/*Interrupt generated when no of words in RX FIFO is greater than this value */
+#define MSM_BOOT_UART_DM_RFW_VALUE 0
+
+/* UART Hunt Character Register */
+#define MSM_BOOT_UART_DM_HCR(base) ((base) + 0x24)
+
+/* Used for RX transfer initialization */
+#define MSM_BOOT_UART_DM_DMRX(base) ((base) + 0x34)
+
+/* Default DMRX value - any value bigger than FIFO size would be fine */
+#define MSM_BOOT_UART_DM_DMRX_DEF_VALUE 0x220
+
+/* Register to enable IRDA function */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0xB8)
+#else
+#define MSM_BOOT_UART_DM_IRDA(base) ((base) + 0x38)
+#endif
+
+/* UART Data Mover Enable Register */
+#define MSM_BOOT_UART_DM_DMEN(base) ((base) + 0x3C)
+
+/* Number of characters for Transmission */
+#define MSM_BOOT_UART_DM_NO_CHARS_FOR_TX(base) ((base) + 0x040)
+
+/* UART RX FIFO Base Address */
+#define MSM_BOOT_UART_DM_BADR(base) ((base) + 0x44)
+
+/* UART Status Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_SR(base) ((base) + 0x0A4)
+#else
+#define MSM_BOOT_UART_DM_SR(base) ((base) + 0x008)
+#endif
+#define MSM_BOOT_UART_DM_SR_RXRDY (1 << 0)
+#define MSM_BOOT_UART_DM_SR_RXFULL (1 << 1)
+#define MSM_BOOT_UART_DM_SR_TXRDY (1 << 2)
+#define MSM_BOOT_UART_DM_SR_TXEMT (1 << 3)
+#define MSM_BOOT_UART_DM_SR_UART_OVERRUN (1 << 4)
+#define MSM_BOOT_UART_DM_SR_PAR_FRAME_ERR (1 << 5)
+#define MSM_BOOT_UART_DM_RX_BREAK (1 << 6)
+#define MSM_BOOT_UART_DM_HUNT_CHAR (1 << 7)
+#define MSM_BOOT_UART_DM_RX_BRK_START_LAST (1 << 8)
+
+/* UART Receive FIFO Registers - 4 in numbers */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x140 + (4*(x)))
+#else
+#define MSM_BOOT_UART_DM_RF(base, x) ((base) + 0x70 + (4*(x)))
+#endif
+
+/* UART Masked Interrupt Status Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_MISR(base) ((base) + 0xAC)
+#else
+#define MSM_BOOT_UART_DM_MISR(base) ((base) + 0x10)
+#endif
+
+/* UART Interrupt Status Register */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_ISR(base) ((base) + 0xB4)
+#else
+#define MSM_BOOT_UART_DM_ISR(base) ((base) + 0x14)
+#endif
+
+/* Number of characters received since the end of last RX transfer */
+#if PERIPH_BLK_BLSP
+#define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0xBC)
+#else
+#define MSM_BOOT_UART_DM_RX_TOTAL_SNAP(base) ((base) + 0x38)
+#endif
+
+/* UART TX FIFO Status Register */
+#define MSM_BOOT_UART_DM_TXFS(base) ((base) + 0x4C)
+#define MSM_BOOT_UART_DM_TXFS_STATE_LSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x, 0, 6)
+#define MSM_BOOT_UART_DM_TXFS_STATE_MSB(x) \
+ MSM_BOOT_UART_DM_EXTR_BITS(x, 14, 31)
+#define MSM_BOOT_UART_DM_TXFS_BUF_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x, 7, 9)
+#define MSM_BOOT_UART_DM_TXFS_ASYNC_STATE(x) \
+ MSM_BOOT_UART_DM_EXTR_BITS(x, 10, 13)
+
+/* UART RX FIFO Status Register */
+#define MSM_BOOT_UART_DM_RXFS(base) ((base) + 0x50)
+#define MSM_BOOT_UART_DM_RXFS_STATE_LSB(x) MSM_BOOT_UART_DM_EXTR_BITS(x, 0, 6)
+#define MSM_BOOT_UART_DM_RXFS_STATE_MSB(x) \
+ MSM_BOOT_UART_DM_EXTR_BITS(x, 14, 31)
+#define MSM_BOOT_UART_DM_RXFS_BUF_STATE(x) MSM_BOOT_UART_DM_EXTR_BITS(x, 7, 9)
+#define MSM_BOOT_UART_DM_RXFS_ASYNC_STATE(x) \
+ MSM_BOOT_UART_DM_EXTR_BITS(x, 10, 13)
+
+/* Macros for Common Errors */
+#define MSM_BOOT_UART_DM_E_SUCCESS 0
+#define MSM_BOOT_UART_DM_E_FAILURE 1
+#define MSM_BOOT_UART_DM_E_TIMEOUT 2
+#define MSM_BOOT_UART_DM_E_INVAL 3
+#define MSM_BOOT_UART_DM_E_MALLOC_FAIL 4
+#define MSM_BOOT_UART_DM_E_RX_NOT_READY 5
+
+void ipq40xx_uart_init(void);
+
+#endif /* __UART_DM_H__ */
diff --git a/src/soc/qualcomm/qcs405/uart.c b/src/soc/qualcomm/qcs405/uart.c
new file mode 100644
index 0000000..7cdc29f
--- /dev/null
+++ b/src/soc/qualcomm/qcs405/uart.c
@@ -0,0 +1,309 @@
+/*
+ * Copyright (c) 2012 The Linux Foundation. All rights reserved.
+ * Source : APQ8064 LK boot
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are
+ * met:
+ * * Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * * Redistributions in binary form must reproduce the above
+ * copyright notice, this list of conditions and the following
+ * disclaimer in the documentation and/or other materials provided
+ * with the distribution.
+ * * Neither the name of The Linux Foundation nor the names of its
+ * contributors may be used to endorse or promote products derived
+ * from this software without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED "AS IS" AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS
+ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
+ * BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
+ * WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
+ * OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN
+ * IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <arch/io.h>
+#include <boot/coreboot_tables.h>
+#include <console/console.h>
+#include <console/uart.h>
+#include <delay.h>
+#include <gpio.h>
+#include <soc/clock.h>
+#include <soc/blsp.h>
+#include <soc/ipq_uart.h>
+#include <soc/cdp.h>
+#include <stdint.h>
+#include <stdlib.h>
+#include <soc/iomap.h>
+
+#define FIFO_DATA_SIZE 4
+
+typedef struct {
+ void *uart_dm_base;
+ //uart_clk_mnd_t mnd_value;
+ unsigned blsp_uart;
+ gpio_func_data_t dbg_uart_gpio[NO_OF_DBG_UART_GPIOS];
+} uart_params_t;
+
+void ipq_configure_gpio(const gpio_func_data_t *gpio, unsigned count)
+{
+ int i;
+
+ for (i = 0; i < count; i++) {
+ gpio_configure(gpio->gpio, gpio->func,
+ gpio->pull, gpio->drvstr, gpio->enable);
+ gpio++;
+ }
+}
+
+static const uart_params_t uart_board_param = {
+ .uart_dm_base = UART2_DM_BASE,
+ //.mnd_value = { 24, 625, 313 },
+ .blsp_uart = BLSP1_UART2,
+ .dbg_uart_gpio = {
+ {
+ .gpio = GPIO(17),
+ .func = 1,
+ .dir = GPIO_OUTPUT,
+ .pull = GPIO_PULL_UP,
+ .enable = GPIO_OUTPUT
+ },
+ {
+ .gpio = GPIO(18),
+ .func = 1,
+ .dir = GPIO_INPUT,
+ .pull = GPIO_NO_PULL,
+ .enable = GPIO_INPUT
+ },
+ },
+};
+
+/**
+ * @brief msm_boot_uart_dm_init_rx_transfer - Init Rx transfer
+ * @param uart_dm_base: UART controller base address
+ */
+static unsigned int msm_boot_uart_dm_init_rx_transfer(void *uart_dm_base)
+{
+ /* Reset receiver */
+ write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
+ MSM_BOOT_UART_DM_CMD_RESET_RX);
+
+ /* Enable receiver */
+ write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
+ MSM_BOOT_UART_DM_CR_RX_ENABLE);
+ write32(MSM_BOOT_UART_DM_DMRX(uart_dm_base),
+ MSM_BOOT_UART_DM_DMRX_DEF_VALUE);
+
+ /* Clear stale event */
+ write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
+ MSM_BOOT_UART_DM_CMD_RES_STALE_INT);
+
+ /* Enable stale event */
+ write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
+ MSM_BOOT_UART_DM_GCMD_ENA_STALE_EVT);
+
+ return MSM_BOOT_UART_DM_E_SUCCESS;
+}
+
+#if IS_ENABLED(CONFIG_DRIVERS_UART)
+static unsigned int msm_boot_uart_dm_init(void *uart_dm_base);
+
+/* Received data is valid or not */
+static int valid_data = 0;
+
+/* Received data */
+static unsigned int word = 0;
+
+
+void uart_tx_byte(int idx, unsigned char data)
+{
+ int num_of_chars = 1;
+ void *base = uart_board_param.uart_dm_base;
+
+ /* Wait until transmit FIFO is empty. */
+ while (!(read32(MSM_BOOT_UART_DM_SR(base)) &
+ MSM_BOOT_UART_DM_SR_TXEMT))
+ udelay(1);
+ /*
+ * TX FIFO is ready to accept new character(s). First write number of
+ * characters to be transmitted.
+ */
+ write32(MSM_BOOT_UART_DM_NO_CHARS_FOR_TX(base), num_of_chars);
+
+ /* And now write the character(s) */
+ write32(MSM_BOOT_UART_DM_TF(base, 0), data);
+}
+#endif /* CONFIG_SERIAL_UART */
+
+/**
+ * @brief msm_boot_uart_dm_reset - resets UART controller
+ * @param base: UART controller base address
+ */
+static unsigned int msm_boot_uart_dm_reset(void *base)
+{
+ write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RESET_RX);
+ write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RESET_TX);
+ write32(MSM_BOOT_UART_DM_CR(base),
+ MSM_BOOT_UART_DM_CMD_RESET_ERR_STAT);
+ write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RES_TX_ERR);
+ write32(MSM_BOOT_UART_DM_CR(base), MSM_BOOT_UART_DM_CMD_RES_STALE_INT);
+
+ return MSM_BOOT_UART_DM_E_SUCCESS;
+}
+
+/**
+ * @brief msm_boot_uart_dm_init - initilaizes UART controller
+ * @param uart_dm_base: UART controller base address
+ */
+unsigned int msm_boot_uart_dm_init(void *uart_dm_base)
+{
+ /* Configure UART mode registers MR1 and MR2 */
+ /* Hardware flow control isn't supported */
+ write32(MSM_BOOT_UART_DM_MR1(uart_dm_base), 0x0);
+
+ /* 8-N-1 configuration: 8 data bits - No parity - 1 stop bit */
+ write32(MSM_BOOT_UART_DM_MR2(uart_dm_base),
+ MSM_BOOT_UART_DM_8_N_1_MODE);
+
+ /* Configure Interrupt Mask register IMR */
+ write32(MSM_BOOT_UART_DM_IMR(uart_dm_base),
+ MSM_BOOT_UART_DM_IMR_ENABLED);
+
+ /*
+ * Configure Tx and Rx watermarks configuration registers
+ * TX watermark value is set to 0 - interrupt is generated when
+ * FIFO level is less than or equal to 0
+ */
+ write32(MSM_BOOT_UART_DM_TFWR(uart_dm_base),
+ MSM_BOOT_UART_DM_TFW_VALUE);
+
+ /* RX watermark value */
+ write32(MSM_BOOT_UART_DM_RFWR(uart_dm_base),
+ MSM_BOOT_UART_DM_RFW_VALUE);
+
+ /* Configure Interrupt Programming Register */
+ /* Set initial Stale timeout value */
+ write32(MSM_BOOT_UART_DM_IPR(uart_dm_base),
+ MSM_BOOT_UART_DM_STALE_TIMEOUT_LSB);
+
+ /* Configure IRDA if required */
+ /* Disabling IRDA mode */
+ write32(MSM_BOOT_UART_DM_IRDA(uart_dm_base), 0x0);
+
+ /* Configure hunt character value in HCR register */
+ /* Keep it in reset state */
+ write32(MSM_BOOT_UART_DM_HCR(uart_dm_base), 0x0);
+
+ /*
+ * Configure Rx FIFO base address
+ * Both TX/RX shares same SRAM and default is half-n-half.
+ * Sticking with default value now.
+ * As such RAM size is (2^RAM_ADDR_WIDTH, 32-bit entries).
+ * We have found RAM_ADDR_WIDTH = 0x7f
+ */
+
+ /* Issue soft reset command */
+ msm_boot_uart_dm_reset(uart_dm_base);
+
+ /* Enable/Disable Rx/Tx DM interfaces */
+ /* Data Mover not currently utilized. */
+ write32(MSM_BOOT_UART_DM_DMEN(uart_dm_base), 0x0);
+
+ /* Enable transmitter */
+ write32(MSM_BOOT_UART_DM_CR(uart_dm_base),
+ MSM_BOOT_UART_DM_CR_TX_ENABLE);
+
+ /* Initialize Receive Path */
+ msm_boot_uart_dm_init_rx_transfer(uart_dm_base);
+
+ return 0;
+}
+
+/**
+ * @brief ipq40xx_uart_init - initializes UART
+ *
+ * Initializes clocks, GPIO and UART controller.
+ */
+void uart_init(int idx)
+{
+ /* Note int idx isn't used in this driver. */
+ void *dm_base;
+
+ dm_base = uart_board_param.uart_dm_base;
+
+ if (read32(MSM_BOOT_UART_DM_CSR(dm_base)) == 0xFF)
+ return; /* UART must have been already initialized. */
+
+ ipq_configure_gpio(uart_board_param.dbg_uart_gpio,
+ NO_OF_DBG_UART_GPIOS);
+
+ /* TODO: Configure the uart clock */
+ /*uart_clock_config(uart_board_param.blsp_uart,
+ uart_board_param.mnd_value.m_value,
+ uart_board_param.mnd_value.n_value,
+ uart_board_param.mnd_value.d_value);*/
+
+ write32(MSM_BOOT_UART_DM_CSR(dm_base), 0xFF);
+
+ /* Initialize UART_DM */
+ msm_boot_uart_dm_init(dm_base);
+}
+
+/* for the benefit of non-console uart init */
+void ipq40xx_uart_init(void)
+{
+ uart_init(0);
+}
+
+/**
+ * @brief uart_tx_flush - transmits a string of data
+ * @param idx: string to transmit
+ */
+void uart_tx_flush(int idx)
+{
+ void *base = uart_board_param.uart_dm_base;
+
+ while (!(read32(MSM_BOOT_UART_DM_SR(base)) &
+ MSM_BOOT_UART_DM_SR_TXEMT))
+ ;
+}
+
+#if IS_ENABLED(CONFIG_DRIVERS_UART)
+/**
+ * ipq40xx_serial_getc - reads a character
+ *
+ * Returns the character read from serial port.
+ */
+uint8_t uart_rx_byte(int idx)
+{
+ uint8_t byte;
+
+ byte = (uint8_t)(word & 0xff);
+ word = word >> 8;
+ valid_data--;
+
+ return byte;
+}
+#endif
+
+#ifndef __PRE_RAM__
+/* TODO: Implement function */
+void uart_fill_lb(void *data)
+{
+ struct lb_serial serial;
+
+ serial.type = LB_SERIAL_TYPE_MEMORY_MAPPED;
+ serial.baseaddr = (uint64_t)UART2_DM_BASE;
+ serial.baud = get_uart_baudrate();
+ serial.regwidth = 1;
+
+ lb_add_serial(&serial, data);
+ lb_add_console(LB_TAG_CONSOLE_SERIAL8250MEM, data);
+}
+#endif
--
To view, visit https://review.coreboot.org/c/coreboot/+/29964
To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings
Gerrit-Project: coreboot
Gerrit-Branch: master
Gerrit-Change-Id: Id9626c68eadead8b8ec5ffbc08cab7b0ec36478f
Gerrit-Change-Number: 29964
Gerrit-PatchSet: 1
Gerrit-Owner: nsekar at codeaurora.org
Gerrit-Reviewer: Martin Roth <martinroth at google.com>
Gerrit-Reviewer: Patrick Georgi <pgeorgi at google.com>
Gerrit-Reviewer: nsekar at codeaurora.org
Gerrit-MessageType: newchange
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mail.coreboot.org/pipermail/coreboot-gerrit/attachments/20181130/280fbd91/attachment-0001.html>
More information about the coreboot-gerrit
mailing list