[flashrom] Intel Z97 chipset

somebody forums at n0sq.tech
Sat Nov 10 23:15:56 CET 2018


flashrom  on Linux 4.18.18-041818-generic (x86_64)
flashrom was built with libpci 3.5.2, GCC 7.3.0, little endian
Command line (5 args): flashrom --programmer internal -V -o result.txt
Using clock_gettime for delay loops (clk_id: 1, resolution: 1ns).
Initializing internal programmer
/sys/class/mtd/mtd0 does not exist
No coreboot table found.
Using Internal DMI decoder.
DMI string chassis-type: "Desktop"
DMI string system-manufacturer: "Gigabyte Technology Co., Ltd."
DMI string system-product-name: "Z97-HD3"
DMI string system-version: "To be filled by O.E.M."
DMI string baseboard-manufacturer: "Gigabyte Technology Co., Ltd."
DMI string baseboard-product-name: "Z97-HD3"
DMI string baseboard-version: "x.x"
Found ITE Super I/O, ID 0x8620 on port 0x2e
Found chipset "Intel Z97" with PCI ID 8086:8cc4.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware
with it,
then please email a report to flashrom at flashrom.org including a verbose
(-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc65: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching enabled, caching enabled,
BIOS_CNTL = 0x09: BIOS Lock Enable: disabled, BIOS Write Enable: enabled
SPIBAR = 0x00007f3d65a61000 + 0x3800
0x04: 0xf008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
SPI Configuration is locked down.
Reading OPCODES... done
        OP        Type      Pre-OP
op[0]: 0x02, write w/  addr, none
op[1]: 0x3b, read  w/  addr, none
op[2]: 0x20, write w/  addr, none
op[3]: 0x05, read  w/o addr, none
op[4]: 0x9f, read  w/o addr, none
op[5]: 0x01, write w/o addr, none
op[6]: 0x00, read  w/o addr, none
op[7]: 0x00, read  w/o addr, none
Pre-OP 0: 0x06, Pre-OP 1: 0x00
0x06: 0x0000 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0
0x08: 0x00000000 (FADDR)
0x50: 0x0000ffff (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff
0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff)
is read-write.
0x58: 0x07ff0000 FREG1: BIOS region (0x00000000-0x007fffff) is read-write.
0x5C: 0x01ff0001 FREG2: Management Engine region (0x00001000-0x001fffff)
is read-write.
0x60: 0x00007fff FREG3: Gigabit Ethernet region is unused.
0x64: 0x00007fff FREG4: Platform Data region is unused.
0x74: 0x00000000 (PR0 is unused)
0x78: 0x00000000 (PR1 is unused)
0x7C: 0x00000000 (PR2 is unused)
0x80: 0x00000000 (PR3 is unused)
0x84: 0x00000000 (PR4 is unused)
0x90: 0xc0 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xfc4010 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=0, SME=0, SCF=4
0x94: 0x0006     (PREOP)
0x96: 0x043b     (OPTYPE)
0x98: 0x05203b02 (OPMENU)
0x9c: 0x0000019f (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80802045 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002045 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x50444653 (FPB)
Reading flash descriptors mapped by the chipset via FDOC/FDOD... done.
=== Content Section ===
FLVALSIG 0x0ff0a55a
FLMAP0   0x02040003
FLMAP1   0x15100206
FLMAP2   0x26210120

--- Details ---
NR          (Number of Regions):                     3
FRBA        (Flash Region Base Address):         0x040
NC          (Number of Components):                  1
FCBA        (Flash Component Base Address):      0x030
ISL         (ICH/PCH Strap Length):                 21
FISBA/FPSBA (Flash ICH/PCH Strap Base Address):  0x100
NM          (Number of Masters):                     3
FMBA        (Flash Master Base Address):         0x060
MSL/PSL     (MCH/PROC Strap Length):                 1
FMSBA       (Flash MCH/PROC Strap Base Address): 0x200

=== Component Section ===
FLCOMP   0x64900044
FLILL    0xad604221

--- Details ---
Component 1 density:            8 MB
Component 2 is not used.
Read Clock Frequency:           20 MHz
Read ID and Status Clock Freq.: 50 MHz
Write and Erase Clock Freq.:    50 MHz
Fast Read is supported.
Fast Read Clock Frequency:      50 MHz
Dual Output Fast Read Support:  disabled
Invalid instruction 0:          0x21
Invalid instruction 1:          0x42
Invalid instruction 2:          0x60
Invalid instruction 3:          0xad

=== Region Section ===
FLREG0   0x00000000
FLREG1   0x07ff0000
FLREG2   0x01ff0001

--- Details ---
Region 0 (Descr. ) 0x00000000 - 0x00000fff
Region 1 (BIOS   ) 0x00000000 - 0x007fffff
Region 2 (ME     ) 0x00001000 - 0x001fffff

=== Master Section ===
FLMSTR1  0xffff0000
FLMSTR2  0xffff0000
FLMSTR3  0xffff0118

--- Details ---
      Descr. BIOS ME GbE Platf.
BIOS    rw    rw  rw  rw   rw
ME      rw    rw  rw  rw   rw
GbE     rw    rw  rw  rw   rw

Enabling hardware sequencing because some important opcode is locked.
OK.
Super I/O ID 0x8620 is not on the list of flash-capable controllers.
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Hardware sequencing
reports 1 attached SPI flash chip with a density of 8192 kB.
The flash address space (0x000000 - 0x7fffff) is divided at address
0x653000 in two partitions.
The first partition ranges from 0x000000 to 0x652fff.
In that range are 1619 erase blocks with 4096 B each.
The second partition ranges from 0x653000 to 0x7fffff.
In that range are 429 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (8192 kB,
Programmer-specific) mapped at physical address 0x0000000000000000.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xc6, id2 0x33,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xc6, id2
0x33, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xc6, id2
0x33, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xea, id2
0xd0, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xe8, id2 0x94,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xc6, id2 0x33, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xe8, id2 0x94, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x00, id2 0x00, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xea, id2 0xd0, id1
is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x00, id2
0x00, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xc6, id2
0x33, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xea,
id2 0xd0, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common:
id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content,
id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (8192 kB,
Programmer-specific).
No operations were specified.
Restoring MMIO space at 0x7f3d65a648a0




More information about the flashrom mailing list