[flashrom] W836xx: Lenovo 3460AQG: flashrom -V

Thomas Nilsen thomas at 3mt.no
Sun Mar 20 23:36:10 CET 2016


flashrom v0.9.7-r1852 on Linux 4.2.0-34-generic (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.2.1, GCC 4.9.1, little endian
Command line (3 args): flashrom -V --programmer internal
Calibrating delay loop... OS timer resolution is 1 usecs, 3174M loops per
second, 10 myus = 10 us, 100 myus = 108 us, 1000 myus = 1001 us, 10000 myus
= 9986 us, 4 myus = 5 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
W836xx enter config mode worked or we were already in config mode. W836xx
leave config mode had no effect.
Active config mode, unknown reg 0x20 ID: 00.
Please send the output of "flashrom -V -p internal" to
flashrom at flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
Found chipset "Intel QS77" with PCI ID 8086:1e56.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with
it,
then please email a report to flashrom at flashrom.org including a verbose
(-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap: enabled (A16(+) inverted)
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x0
0xffe00000/0xffa00000 FWH IDSEL: 0x0
0xffd80000/0xff980000 FWH IDSEL: 0x0
0xffd00000/0xff900000 FWH IDSEL: 0x0
0xffc80000/0xff880000 FWH IDSEL: 0x0
0xffc00000/0xff800000 FWH IDSEL: 0xf
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x380000 bytes
SPI Read Configuration: prefetching enabled, caching enabled,
BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
Warning: BIOS region SMM protection is enabled!
Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed.
New value is 0x2a.
SPIBAR = 0x00007ffa22eea000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x50: 0x00000a0b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b
0x54: 0x00000000 FREG0: Warning: Flash Descriptor region
(0x00000000-0x00000fff) is read-only.
0x58: 0x0bff0500 FREG1: BIOS region (0x00500000-0x00bfffff) is read-write.
0x5C: 0x04ff0003 FREG2: Warning: Management Engine region
(0x00003000-0x004fffff) is locked.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is
read-write.
Not all flash regions are freely accessible by flashrom. This is most likely
due to an active ME. Please see http://flashrom.org/ME for details.
0x74: 0x8aaf0800 PR0: Warning: 0x00800000-0x00aaffff is read-only.
0x78: 0x8ade0ad0 PR1: Warning: 0x00ad0000-0x00adefff is read-only.
0x7C: 0x8b100b10 PR2: Warning: 0x00b10000-0x00b10fff is read-only.
0x80: 0x8bff0b40 PR3: Warning: 0x00b40000-0x00bfffff is read-only.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0xc0 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf80000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0
0x94: 0x0606     (PREOP)
0x96: 0x0fe4     (OPTYPE)
0x98: 0x02030105 (OPMENU)
0x9C: 0xff9f20d8 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00802005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x00000000 (FPB)
Enabling hardware sequencing due to multiple flash chips detected.
PROBLEMS, continuing anyway
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Found 2 attached SPI flash
chips with a combined density of 12288 kB.
There is only one partition containing the whole address space (0x000000 -
0xbfffff).
There are 3072 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (12288 kB,
Programmer-specific) mapped at physical address 0x0000000000000000.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x01, id2 0x00, id1
is normal flash content, id2 is normal flash content
Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0x6e, id2 0x81,
id1 is normal flash content, id2 is normal flash content
Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1
is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1
is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1
is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x01, id2 0x00,
id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x6e, id2 0x81,
id1 is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1
is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x01, id2
0x00, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x28, id2
0x68, id1 parity violation, id1 is normal flash content, id2 is normal
flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x6e, id2
0x81, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1
is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xec, id2
0xba, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xec, id2 0xba,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0x29, id2 0xc1,
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1
is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1
is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1
is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1
is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x01, id2 0x00, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0x29, id2 0xc1, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x6e, id2 0x81, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xec, id2 0xba, id1 is
normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x6e, id2
0x81, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x6e, id2
0x81, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x6e, id2
0x81, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x01, id2
0x00, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xec, id2
0xba, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1
0x6e, id2 0x81, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (12288 kB,
Programmer-specific).
No operations were specified.
Restoring MMIO space at 0x7ffa22eed8a0
Restoring PCI config space for 00:1f:0 reg 0xdc




---------------
dmidecode output for machine & bios;

Handle 0x000C, DMI type 0, 24 bytes
BIOS Information
        Vendor: LENOVO
        Version: G6ETB2WW (2.72 )
        Release Date: 10/08/2015
        Address: 0xE0000
        Runtime Size: 128 kB
        ROM Size: 12288 kB
        Characteristics:
                PCI is supported
                PNP is supported
                BIOS is upgradeable
                BIOS shadowing is allowed
                Boot from CD is supported
                Selectable boot is supported
                EDD is supported
                3.5"/720 kB floppy services are supported (int 13h)
                Print screen service is supported (int 5h)
                8042 keyboard services are supported (int 9h)
                Serial services are supported (int 14h)
                Printer services are supported (int 17h)
                CGA/mono video services are supported (int 10h)
                ACPI is supported
                USB legacy is supported
                BIOS boot specification is supported
                Targeted content distribution is supported
                UEFI is supported
        BIOS Revision: 2.72
        Firmware Revision: 1.6

Handle 0x000D, DMI type 1, 27 bytes
System Information
        Manufacturer: LENOVO
        Product Name: 3460AQG
        Version: ThinkPad X1 Carbon
        Serial Number: ******
        UUID: ******
        Wake-up Type: Power Switch
        SKU Number: LENOVO_MT_3460
        Family: ThinkPad X1 Carbon



-- 

*Thomas Nilsen*
3mt Communications AS
PB 195, 1112 Oslo, Norway
(+47) 41888888 | thomas at 3mt.no | www.3mt.no
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.flashrom.org/pipermail/flashrom/attachments/20160320/08c17524/attachment.html>


More information about the flashrom mailing list