[flashrom] T440p flashrom -V

[Martin Kjær Jørgensen]

flashrom asked me to send you this output, so I did. Hope it helps.

/Martin

flashrom v0.9.7-r1782 on Linux 3.14-1-amd64 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian
Command line (3 args): flashrom -p internal -V
Calibrating delay loop... OS timer resolution is 1 usecs, 3313M loops per
second, 10 myus = 10 us, 100 myus = 118 us, 1000 myus = 997 us, 10000 myus =
9897 us, 4 myus = 15 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
W836xx enter config mode worked or we were already in config mode. W836xx leave
config mode had no effect.
Active config mode, unknown reg 0x20 ID: 00.
Please send the output of "flashrom -V" to
flashrom at flashrom.org with W836xx: your board name: flashrom -V
as the subject to help us finish support for your Super I/O. Thanks.
Found chipset "Intel QM87" with PCI ID 8086:8c4f.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom at flashrom.org including a verbose (-V)
log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI)
Top Swap : not enabled

0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytesSPI Read Configuration: prefetching
enabled, caching enabled,
BIOS_CNTL = 0x2b: BIOS Lock Enable: enabled, BIOS Write Enable: enabled
Warning: BIOS region SMM protection is enabled!
Warning: Setting Bios Control at 0xdc from 0x2a to 0x09 failed.
New value is 0x2b.
SPIBAR = 0x00007f85a7697000 + 0x3800
0x04: 0xf008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x50: 0x00004a4b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x4a, BRRA 0x4b
0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff)
is read-only.
0x58: 0x0bff0500 FREG1: BIOS region (0x00500000-0x00bfffff) is read-write.
0x5C: 0x04ff0003 FREG2: Warning: Management Engine region
(0x00003000-0x004fffff) is locked.
0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is
read-write.
Not all flash regions are freely accessible by flashrom. This is most likely
due to an active ME. Please see http://flashrom.org/ME for details.
0x78: 0x8bff0b40 PR1: Warning: 0x00b40000-0x00bfffff is read-only.
0x7C: 0x8adf0ab1 PR2: Warning: 0x00ab1000-0x00adffff is read-only.
0x80: 0x8ab00ab0 PR3: Warning: 0x00ab0000-0x00ab0fff is read-only.
0x84: 0x8aaf0800 PR4: Warning: 0x00800000-0x00aaffff is read-only.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0xc0 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xf94000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=1
0x94: 0x0606     (PREOP)
0x96: 0x3f90     (OPTYPE)
0x98: 0x03013505 (OPMENU)
0x9C: 0x9f20d802 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80802025 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x80002025 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0
0xD0: 0x00f12005 (FPB)

Enabling hardware sequencing due to multiple flash chips detected.
Density of ICH SPI component with index 1 is invalid. Encoded density is 0x6.
OK.
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip
with a density of 8192 kB.
The flash address space (0x000000 - 0x7fffff) is divided at address 0x005000 in
two partitions.
The first partition ranges from 0x000000 to 0x004fff.
In that range are 5 erase blocks with 4096 B each.
The second partition ranges from 0x005000 to 0x7fffff.
In that range are 2043 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific)
at physical address 0x0.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x00, id2 0x00, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x80, id2 0x03, id1
is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x83, id2 0xc4,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x3b, id2 0x04,
id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported
size 1024 kB of chipset/board/programmer for FWH interface,
probe/read/erase/write may fail. probe_82802ab: id1 0x70, id2 0xf2, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity
violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported
size 1024 kB of chipset/board/programmer for FWH interface,
probe/read/erase/write may fail. probe_82802ab: id1 0x70, id2 0xf2, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x80, id2 0x03, id1 is
normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x3b, id2 0x04, id1 is
normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x80, id2 0x03,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x00, id2 0x00,
id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x3b, id2 0x04,
id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x80,
id2 0x03, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific).
No operations were specified.
Restoring MMIO space at 0x7f85a769a8a0
Restoring PCI config space for 00:1f:0 reg 0xdc