[flashrom] [PATCH] Trivial: fix spelling in comments and a string

[dforsi at gmail.com]

This fixes 5 errors found running codespell on the sources.
Codespell is at https://github.com/lucasdemarchi/codespell

Signed-off-by: Daniele Forsi <dforsi at gmail.com>

Index: Documentation/serprog-protocol.txt
===================================================================
--- Documentation/serprog-protocol.txt	(revision 1830)
+++ Documentation/serprog-protocol.txt	(working copy)
@@ -74,7 +74,7 @@
 		Send and receive bytes via SPI.
 		Maximum slen is Q_WRNMAXLEN in case Q_BUSTYPE returns SPI only or S_BUSTYPE was used
 		to set SPI exclusively before. Same for rlen and Q_RDNMAXLEN.
-		This operation is immediate, meaning it doesnt use the operation buffer.
+		This operation is immediate, meaning it doesn't use the operation buffer.
 	0x14 (S_SPI_FREQ):
 		Set the SPI clock frequency. The 32-bit value indicates the
 		requested frequency in Hertz. Value 0 is reserved and should
Index: atavia.c
===================================================================
--- atavia.c	(revision 1830)
+++ atavia.c	(working copy)
@@ -113,7 +113,7 @@
 	}
 
 	msg_pdbg2("\n%s: %s after %d tries (access=0x%02x, status=0x%02x)\n",
-		  __func__, ready ? "suceeded" : "failed", try, access, status);
+		  __func__, ready ? "succeeded" : "failed", try, access, status);
 	atavia_prettyprint_access(access);
 	return ready;
 }
Index: dmi.c
===================================================================
--- dmi.c	(revision 1830)
+++ dmi.c	(working copy)
@@ -188,7 +188,7 @@
 		/* - If a short entry is found (less than 4 bytes), not only it
 		 *   is invalid, but we cannot reliably locate the next entry.
 		 * - If the length value indicates that this structure spreads
-		 *   accross the table border, something is fishy too.
+		 *   across the table border, something is fishy too.
 		 * Better stop at this point, and let the user know his/her
 		 * table is broken.
 		 */
Index: flashchips.c
===================================================================
--- flashchips.c	(revision 1830)
+++ flashchips.c	(working copy)
@@ -6327,7 +6327,7 @@
 				.block_erase = spi_block_erase_c7,
 			},
 		},
-		.printlock	= spi_prettyprint_status_register_bp3_srwd, /* bit6: Continously Program (CP) mode */
+		.printlock	= spi_prettyprint_status_register_bp3_srwd, /* bit6: Continuously Program (CP) mode */
 		.unlock		= spi_disable_blockprotect,
 		.write		= spi_chip_write_256,
 		.read		= spi_chip_read, /* Fast read (0x0B), dual I/O supported */
Index: flashrom.8.tmpl
===================================================================
--- flashrom.8.tmpl	(revision 1830)
+++ flashrom.8.tmpl	(working copy)
@@ -772,7 +772,7 @@
 .B value
 can be
 .BR 1 " or " 2
-to select target chip 1 or 2 repectively. The default is target chip 1.
+to select target chip 1 or 2 respectively. The default is target chip 1.
 .SS
 .BR "rayer_spi " programmer
 The default I/O base address used for the parallel port is 0x378 and you can use