[flashrom] "MX25L12805(D)

[Skip WB6YMH]

Sorry, I didn't create a log.  If I didn't have to solder wires
to my flash chip I'd try to recreate it for you.  My soldering
"skills" aren't !

The best I can do is the following which was still on
my screen.  Run under Ubuntu 10.04 on a Dell Optiplex 745
with a Intel Pentium D CPU 3.40GHz.

Code was pulled from svn on 4/16 (rev 1669).

Skip

---
skip at lucid:~/flashrom/new$ sudo ../flashrom -p
ft2232_spi:type=tumpa,port=B  -w new.bin
flashrom v0.9.6.1-r1669 on Linux 2.6.32-37-generic-pae (i686)
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OK.
Found Macronix flash chip "MX25L12805(D)" (16384 kB, SPI) on ft2232_spi.
===
This flash part has status UNTESTED for operations: READ ERASE WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to flashrom at flashrom.org if any of the above
operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -Vr,
-VE, -Vw), and mention which mainboard or programmer you tested.
Please mention your board in the subject line. Thanks for your help!
Reading old flash chip contents... ftdi_read_data: -19, usb bulk read failed
get_buf failed: 1
ftdi_write_data: -19, usb bulk write failed
send_buf failed at end: 1
FAILED.
skip at lucid:~/flashrom/new$ sudo ../flashrom -p
ft2232_spi:type=tumpa,port=B  -w new.bin
flashrom v0.9.6.1-r1669 on Linux 2.6.32-37-generic-pae (i686)
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OK.
Found Macronix flash chip "MX25L12805(D)" (16384 kB, SPI) on ft2232_spi.
===
This flash part has status UNTESTED for operations: READ ERASE WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to flashrom at flashrom.org if any of the above
operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -Vr,
-VE, -Vw), and mention which mainboard or programmer you tested.
Please mention your board in the subject line. Thanks for your help!
Reading old flash chip contents... done.
Erasing and writing flash chip... Erase/write done.
Verifying flash... VERIFIED.
skip at lucid:~/flashrom/new$
---



On Mon, Apr 22, 2013 at 2:37 PM, Stefan Tauner <
stefan.tauner at student.tuwien.ac.at> wrote:

> On Mon, 22 Apr 2013 13:24:44 -0700
> Skip WB6YMH <wb6ymh at gfrn.org> wrote:
>
> > I'd like to let you know that I successfully programmed the above
> > chip using a ft2232 based "TUMPA" interface card.  I've programmed
> > two chips on two separate boards, but worked fine and booted
> > Linux.
> >
> > I did get one  "get_buf failed: 1
> > ftdi_write_data: -19, usb bulk write failed
> > send_buf failed at end: 1
> > FAILED."
> >
> > Error, but that probably has nothing to do with the MX25L12805(D) chip.
> >
> > Thanks for the code !
> >
> > Skip
>
>
> Hello Skip,
>
> thanks for your report!
> I have marked the flash chip as fully tested and will commit that later
> together with other small changes.
>
> Please include the complete log in future reports (and an additional
> one with verbose output (-V) if the normal run did not include that).
> That's especially interesting for error cases such as the one you
> mentioned. Do you remember when the error occurred exactly?
> --
> Kind regards/Mit freundlichen Grüßen, Stefan Tauner
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.flashrom.org/pipermail/flashrom/attachments/20130422/eb0c26c4/attachment.html>