[flashrom] FAILED: AXIOMTEK PICO821 REV:A2-RC
Recovery.se
info at recovery.se
Thu Feb 9 16:51:13 CET 2012
Hello
I'm very pleased with flashrom! Hovever we have a problem erasing.
I can work around it by running erase (flashrom -E) sevral times and
then flash with (flashrom -w <rom>).
When I run errase the falure posision moves forward
..
"ERASE FAILED at 0x00030000!"
"ERASE FAILED at 0x00040000!"
"ERASE FAILED at 0x000ef000!"
...
Regards
Eric Eriksson
Recovery.se
-------------- next part --------------
flashrom v0.9.4-runknown on Linux 2.6.31-19-generic-pae (i686), built with libpci 3.0.0, GCC 4.4.3, little endian
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 2 usecs, 365M loops per second, 10 myus = 10 us, 100 myus = 101 us, 1000 myus = 1024 us, 10000 myus = 10005 us, 8 myus = 9 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: " "
DMI string system-product-name: " "
DMI string system-version: " "
DMI string baseboard-manufacturer: " "
DMI string baseboard-product-name: "POULSBO"
DMI string baseboard-version: " "
DMI string chassis-type: "Desktop"
Found chipset "Intel SCH Poulsbo" with PCI ID 8086:8119. Enabling flash write...
BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1
BIOS Prefetch Enable: disabled, OK.
The following protocols are supported: FWH.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Found SST flash chip "SST49LF008A" (1024 kB, FWH) at physical address 0xfff00000.
Lock status for 0x000000 (size 0x010000) is 00, full access
Lock status for 0x010000 (size 0x010000) is 00, full access
Lock status for 0x020000 (size 0x010000) is 00, full access
Lock status for 0x030000 (size 0x010000) is 00, full access
Lock status for 0x040000 (size 0x010000) is 00, full access
Lock status for 0x050000 (size 0x010000) is 00, full access
Lock status for 0x060000 (size 0x010000) is 00, full access
Lock status for 0x070000 (size 0x010000) is 00, full access
Lock status for 0x080000 (size 0x010000) is 00, full access
Lock status for 0x090000 (size 0x010000) is 00, full access
Lock status for 0x0a0000 (size 0x010000) is 00, full access
Lock status for 0x0b0000 (size 0x010000) is 00, full access
Lock status for 0x0c0000 (size 0x010000) is 00, full access
Lock status for 0x0d0000 (size 0x010000) is 00, full access
Lock status for 0x0e0000 (size 0x010000) is 00, full access
Lock status for 0x0f0000 (size 0x010000) is 00, full access
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xbf, id2 0x5a
Found SST flash chip "SST49LF008A" (1024 kB, FWH).
Lock status for 0x000000 (size 0x010000) is 00, full access
Lock status for 0x010000 (size 0x010000) is 00, full access
Lock status for 0x020000 (size 0x010000) is 00, full access
Lock status for 0x030000 (size 0x010000) is 00, full access
Lock status for 0x040000 (size 0x010000) is 00, full access
Lock status for 0x050000 (size 0x010000) is 00, full access
Lock status for 0x060000 (size 0x010000) is 00, full access
Lock status for 0x070000 (size 0x010000) is 00, full access
Lock status for 0x080000 (size 0x010000) is 00, full access
Lock status for 0x090000 (size 0x010000) is 00, full access
Lock status for 0x0a0000 (size 0x010000) is 00, full access
Lock status for 0x0b0000 (size 0x010000) is 00, full access
Lock status for 0x0c0000 (size 0x010000) is 00, full access
Lock status for 0x0d0000 (size 0x010000) is 00, full access
Lock status for 0x0e0000 (size 0x010000) is 00, full access
Lock status for 0x0f0000 (size 0x010000) is 00, full access
Erasing and writing flash chip... Trying erase function 0... 0x000000-0x000fff:EERASE FAILED at 0x00000000! Expected=0xff, Read=0x40, failed byte count from 0x00000000-0x00000fff: 0x94f
ERASE FAILED!
Reading current flash chip contents... done. Looking for another erase function.
Trying erase function 1... 0x000000-0x00ffff:S, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:S, 0x050000-0x05ffff:S, 0x060000-0x06ffff:S, 0x070000-0x07ffff:S, 0x080000-0x08ffff:S, 0x090000-0x09ffff:S, 0x0a0000-0x0affff:S, 0x0b0000-0x0bffff:S, 0x0c0000-0x0cffff:S, 0x0d0000-0x0dffff:EERASE FAILED at 0x000d0000! Expected=0xff, Read=0x40, failed byte count from 0x000d0000-0x000dffff: 0x90b
ERASE FAILED!
Looking for another erase function.
No usable erase functions left.
FAILED!
Your flash chip is in an unknown state.
Get help on IRC at irc.freenode.net (channel #flashrom) or
mail flashrom at flashrom.org with FAILED: your board name in the subject line!
-------------------------------------------------------------------------------
DO NOT REBOOT OR POWEROFF!
-------------- next part --------------
flashrom v0.9.4-runknown on Linux 2.6.31-19-generic-pae (i686), built with libpci 3.0.0, GCC 4.4.3, little endian
flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK.
Found chipset "Intel SCH Poulsbo". Enabling flash write... OK.
Found SST flash chip "SST49LF008A" (1024 kB, FWH) at physical address 0xfff00000.
No operations were specified.
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at fdf00000 (32-bit, non-prefetchable) [size=512K]
I/O ports at ff00 [size=8]
Memory at d0000000 (32-bit, non-prefetchable) [size=256M]
Memory at fdf80000 (32-bit, non-prefetchable) [size=256K]
Capabilities: [d0] Power Management version 2
Capabilities: [b0] Vendor Specific Information <?>
Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-
00:1a.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB Client Controller (rev 07) (prog-if 80)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [50] Power Management version 2
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at fdff8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Capabilities: [100] Virtual Channel <?>
Capabilities: [130] Root Complex Link <?>
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07)
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fdb00000-fdbfffff
Prefetchable memory behind bridge: fde00000-fdefffff
Capabilities: [40] Express Root Port (Slot-), MSI 00
Capabilities: [90] Subsystem: Device 8100:8086
Capabilities: [a0] Power Management version 2
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 16
I/O ports at fe00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 17
I/O ports at fd00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 18
I/O ports at fc00 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07) (prog-if 20)
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0, IRQ 19
Memory at fdffe000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Kernel driver in use: ehci_hcd
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)
Subsystem: Device 8100:8086
Flags: fast devsel
Kernel driver in use: isch_smbus
Kernel modules: i2c-isch
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07) (prog-if 80 [Master])
Subsystem: Device 8100:8086
Flags: bus master, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at fb00 [size=16]
Kernel driver in use: pata_sch
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
Subsystem: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller
Flags: bus master, fast devsel, latency 0, IRQ 24
I/O ports at ee00 [size=256]
Memory at fdbff000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at fde00000 [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Capabilities: [48] Vital Product Data <?>
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Capabilities: [60] Express Endpoint, MSI 00
Capabilities: [84] Vendor Specific Information <?>
Capabilities: [100] Advanced Error Reporting <?>
Capabilities: [12c] Virtual Channel <?>
Capabilities: [148] Device Serial Number 68-81-ec-10-00-00-00-c4
Capabilities: [154] Power Budgeting <?>
Kernel driver in use: r8169
Kernel modules: r8169
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation System Controller Hub (SCH Poulsbo) (rev 07)
00:02.0 VGA compatible controller: Intel Corporation System Controller Hub (SCH Poulsbo) Graphics Controller (rev 07)
00:1a.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB Client Controller (rev 07)
00:1b.0 Audio device: Intel Corporation System Controller Hub (SCH Poulsbo) HD Audio Controller (rev 07)
00:1c.0 PCI bridge: Intel Corporation System Controller Hub (SCH Poulsbo) PCI Express Port 1 (rev 07)
00:1d.0 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #1 (rev 07)
00:1d.1 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #2 (rev 07)
00:1d.2 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB UHCI #3 (rev 07)
00:1d.7 USB Controller: Intel Corporation System Controller Hub (SCH Poulsbo) USB EHCI #1 (rev 07)
00:1f.0 ISA bridge: Intel Corporation System Controller Hub (SCH Poulsbo) LPC Bridge (rev 07)
00:1f.1 IDE interface: Intel Corporation System Controller Hub (SCH Poulsbo) IDE Controller (rev 07)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
More information about the flashrom
mailing list