[flashrom] Tyan S3992 Success

Corey Jewett cj at syntheticplayground.com
Fri Oct 21 04:39:24 CEST 2011


Special thanks to dashcloud on IRC for holding my hand.

Mobo: http://www.tyan.com/product_board_detail.aspx?pid=235

Upgrading to latest BIOS for dual-proc quad core support.

Did not lose my MAC addresses. Eight cores of joy. Wish I'd found  
Flashrom before wasting a couple hours noodling through endless  
variations of freedos thumb drive messes.


tweakerO ~ # flashrom -Vw 3992V205.ROM
flashrom v0.9.4-r1395 on Linux 2.6.36-gentoo-r8 (x86_64), built with  
libpci 3.1.7, GCC 4.4.5, little endian
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OS timer resolution is 1 usecs, 595M loops  
per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1011 us,  
10000 myus = 10023 us, 4 myus = 5 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "empty"
DMI string system-product-name: "empty"
DMI string system-version: "empty"
DMI string baseboard-manufacturer: "TYAN Computer Corporation"
DMI string baseboard-product-name: "S3992"
DMI string baseboard-version: "empty"
DMI string chassis-type: "Desktop"
Found chipset "Broadcom HT-1000" with PCI ID 1166:0205. Enabling flash  
write... OK.
This chipset supports the following protocols: Non-SPI.
Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0x0b,  
id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0x0b,  
id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0x0b,  
id2 0xf2
Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0x0b,  
id2 0xf2
Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0x0b,  
id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1  
0x32, id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1  
0x0b, id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1  
0x0b, id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1  
0x0b, id2 0xf2, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1  
0x0b, id2 0xf2, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x0b, id2 0x76,  
id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for Macronix MX29F002B, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29F002T, 256 kB: probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0x0b,  
id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0x0b,  
id2 0x76, id1 is normal flash content, id2 is normal flash content
Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0x32,  
id2 0x69, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0xbf,  
id2 0x5b
Found SST flash chip "SST49LF080A" (1024 kB, LPC) at physical address  
0xfff00000.
Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0x0b, id2 0xf2
Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0x0b, id2 0xf2
Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0x0b, id2  
0x76, id1 is normal flash content, id2 is normal flash content
Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x10, id2  
0x9e, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x0b, id2 0x76,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x0b, id2 0x76,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x32, id2 0x69,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x0b, id2 0x76,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0x32, id2  
0x69, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB:  
Old Winbond W29* probe method disabled because the probing sequence  
puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/ 
W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip.
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common:  
id1 0xbf, id2 0x5b
Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common:  
id1 0xbf, id2 0x5b
Flash image seems to be a legacy BIOS. Disabling coreboot-related  
checks.
Reading old flash chip contents... done.
Erasing and writing flash chip... Trying erase function 0...  
0x000000-0x000fff:S, 0x001000-0x001fff:S, 0x002000-0x002fff:S,  
0x003000-0x003fff:S, 0x004000-0x004fff:S, 0x005000-0x005fff:S,  
0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S,  
0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:S,  
0x00c000-0x00cfff:S, 0x00d000-0x00dfff:S, 0x00e000-0x00efff:S,  
0x00f000-0x00ffff:S, 0x010000-0x010fff:S, 0x011000-0x011fff:S,  
0x012000-0x012fff:S, 0x013000-0x013fff:S, 0x014000-0x014fff:S,  
0x015000-0x015fff:S, 0x016000-0x016fff:S, 0x017000-0x017fff:S,  
0x018000-0x018fff:S, 0x019000-0x019fff:S, 0x01a000-0x01afff:S,  
0x01b000-0x01bfff:S, 0x01c000-0x01cfff:S, 0x01d000-0x01dfff:S,  
0x01e000-0x01efff:S, 0x01f000-0x01ffff:S, 0x020000-0x020fff:S,  
0x021000-0x021fff:S, 0x022000-0x022fff:S, 0x023000-0x023fff:S,  
0x024000-0x024fff:S, 0x025000-0x025fff:S, 0x026000-0x026fff:S,  
0x027000-0x027fff:S, 0x028000-0x028fff:S, 0x029000-0x029fff:S,  
0x02a000-0x02afff:S, 0x02b000-0x02bfff:S, 0x02c000-0x02cfff:W,  
0x02d000-0x02dfff:W, 0x02e000-0x02efff:W, 0x02f000-0x02ffff:W,  
0x030000-0x030fff:W, 0x031000-0x031fff:W, 0x032000-0x032fff:W,  
0x033000-0x033fff:W, 0x034000-0x034fff:W, 0x035000-0x035fff:W,  
0x036000-0x036fff:W, 0x037000-0x037fff:W, 0x038000-0x038fff:W,  
0x039000-0x039fff:W, 0x03a000-0x03afff:W, 0x03b000-0x03bfff:W,  
0x03c000-0x03cfff:W, 0x03d000-0x03dfff:W, 0x03e000-0x03efff:W,  
0x03f000-0x03ffff:W, 0x040000-0x040fff:W, 0x041000-0x041fff:W,  
0x042000-0x042fff:W, 0x043000-0x043fff:W, 0x044000-0x044fff:W,  
0x045000-0x045fff:W, 0x046000-0x046fff:W, 0x047000-0x047fff:W,  
0x048000-0x048fff:W, 0x049000-0x049fff:W, 0x04a000-0x04afff:W,  
0x04b000-0x04bfff:W, 0x04c000-0x04cfff:W, 0x04d000-0x04dfff:EW,  
0x04e000-0x04efff:EW, 0x04f000-0x04ffff:EW, 0x050000-0x050fff:EW,  
0x051000-0x051fff:EW, 0x052000-0x052fff:EW, 0x053000-0x053fff:EW,  
0x054000-0x054fff:EW, 0x055000-0x055fff:EW, 0x056000-0x056fff:EW,  
0x057000-0x057fff:EW, 0x058000-0x058fff:EW, 0x059000-0x059fff:EW,  
0x05a000-0x05afff:EW, 0x05b000-0x05bfff:EW, 0x05c000-0x05cfff:EW,  
0x05d000-0x05dfff:EW, 0x05e000-0x05efff:EW, 0x05f000-0x05ffff:EW,  
0x060000-0x060fff:EW, 0x061000-0x061fff:EW, 0x062000-0x062fff:EW,  
0x063000-0x063fff:EW, 0x064000-0x064fff:EW, 0x065000-0x065fff:EW,  
0x066000-0x066fff:EW, 0x067000-0x067fff:EW, 0x068000-0x068fff:EW,  
0x069000-0x069fff:EW, 0x06a000-0x06afff:EW, 0x06b000-0x06bfff:EW,  
0x06c000-0x06cfff:EW, 0x06d000-0x06dfff:EW, 0x06e000-0x06efff:EW,  
0x06f000-0x06ffff:EW, 0x070000-0x070fff:EW, 0x071000-0x071fff:EW,  
0x072000-0x072fff:EW, 0x073000-0x073fff:EW, 0x074000-0x074fff:EW,  
0x075000-0x075fff:EW, 0x076000-0x076fff:EW, 0x077000-0x077fff:EW,  
0x078000-0x078fff:EW, 0x079000-0x079fff:EW, 0x07a000-0x07afff:EW,  
0x07b000-0x07bfff:EW, 0x07c000-0x07cfff:EW, 0x07d000-0x07dfff:EW,  
0x07e000-0x07efff:EW, 0x07f000-0x07ffff:EW, 0x080000-0x080fff:EW,  
0x081000-0x081fff:EW, 0x082000-0x082fff:EW, 0x083000-0x083fff:EW,  
0x084000-0x084fff:EW, 0x085000-0x085fff:EW, 0x086000-0x086fff:EW,  
0x087000-0x087fff:EW, 0x088000-0x088fff:EW, 0x089000-0x089fff:EW,  
0x08a000-0x08afff:EW, 0x08b000-0x08bfff:EW, 0x08c000-0x08cfff:EW,  
0x08d000-0x08dfff:EW, 0x08e000-0x08efff:EW, 0x08f000-0x08ffff:EW,  
0x090000-0x090fff:EW, 0x091000-0x091fff:EW, 0x092000-0x092fff:EW,  
0x093000-0x093fff:EW, 0x094000-0x094fff:EW, 0x095000-0x095fff:EW,  
0x096000-0x096fff:EW, 0x097000-0x097fff:EW, 0x098000-0x098fff:EW,  
0x099000-0x099fff:EW, 0x09a000-0x09afff:EW, 0x09b000-0x09bfff:EW,  
0x09c000-0x09cfff:EW, 0x09d000-0x09dfff:EW, 0x09e000-0x09efff:EW,  
0x09f000-0x09ffff:EW, 0x0a0000-0x0a0fff:EW, 0x0a1000-0x0a1fff:EW,  
0x0a2000-0x0a2fff:EW, 0x0a3000-0x0a3fff:EW, 0x0a4000-0x0a4fff:EW,  
0x0a5000-0x0a5fff:EW, 0x0a6000-0x0a6fff:EW, 0x0a7000-0x0a7fff:EW,  
0x0a8000-0x0a8fff:EW, 0x0a9000-0x0a9fff:EW, 0x0aa000-0x0aafff:EW,  
0x0ab000-0x0abfff:EW, 0x0ac000-0x0acfff:EW, 0x0ad000-0x0adfff:EW,  
0x0ae000-0x0aefff:EW, 0x0af000-0x0affff:EW, 0x0b0000-0x0b0fff:EW,  
0x0b1000-0x0b1fff:EW, 0x0b2000-0x0b2fff:EW, 0x0b3000-0x0b3fff:EW,  
0x0b4000-0x0b4fff:EW, 0x0b5000-0x0b5fff:EW, 0x0b6000-0x0b6fff:EW,  
0x0b7000-0x0b7fff:EW, 0x0b8000-0x0b8fff:EW, 0x0b9000-0x0b9fff:EW,  
0x0ba000-0x0bafff:EW, 0x0bb000-0x0bbfff:EW, 0x0bc000-0x0bcfff:EW,  
0x0bd000-0x0bdfff:EW, 0x0be000-0x0befff:EW, 0x0bf000-0x0bffff:EW,  
0x0c0000-0x0c0fff:EW, 0x0c1000-0x0c1fff:EW, 0x0c2000-0x0c2fff:EW,  
0x0c3000-0x0c3fff:EW, 0x0c4000-0x0c4fff:EW, 0x0c5000-0x0c5fff:EW,  
0x0c6000-0x0c6fff:EW, 0x0c7000-0x0c7fff:EW, 0x0c8000-0x0c8fff:EW,  
0x0c9000-0x0c9fff:EW, 0x0ca000-0x0cafff:EW, 0x0cb000-0x0cbfff:EW,  
0x0cc000-0x0ccfff:EW, 0x0cd000-0x0cdfff:EW, 0x0ce000-0x0cefff:EW,  
0x0cf000-0x0cffff:EW, 0x0d0000-0x0d0fff:EW, 0x0d1000-0x0d1fff:EW,  
0x0d2000-0x0d2fff:EW, 0x0d3000-0x0d3fff:EW, 0x0d4000-0x0d4fff:EW,  
0x0d5000-0x0d5fff:EW, 0x0d6000-0x0d6fff:EW, 0x0d7000-0x0d7fff:EW,  
0x0d8000-0x0d8fff:EW, 0x0d9000-0x0d9fff:S, 0x0da000-0x0dafff:S,  
0x0db000-0x0dbfff:S, 0x0dc000-0x0dcfff:S, 0x0dd000-0x0ddfff:S,  
0x0de000-0x0defff:S, 0x0df000-0x0dffff:EW, 0x0e0000-0x0e0fff:S,  
0x0e1000-0x0e1fff:S, 0x0e2000-0x0e2fff:S, 0x0e3000-0x0e3fff:S,  
0x0e4000-0x0e4fff:S, 0x0e5000-0x0e5fff:S, 0x0e6000-0x0e6fff:S,  
0x0e7000-0x0e7fff:S, 0x0e8000-0x0e8fff:S, 0x0e9000-0x0e9fff:S,  
0x0ea000-0x0eafff:S, 0x0eb000-0x0ebfff:S, 0x0ec000-0x0ecfff:E,  
0x0ed000-0x0edfff:E, 0x0ee000-0x0eefff:E, 0x0ef000-0x0effff:S,  
0x0f0000-0x0f0fff:EW, 0x0f1000-0x0f1fff:EW, 0x0f2000-0x0f2fff:EW,  
0x0f3000-0x0f3fff:EW, 0x0f4000-0x0f4fff:EW, 0x0f5000-0x0f5fff:EW,  
0x0f6000-0x0f6fff:EW, 0x0f7000-0x0f7fff:EW, 0x0f8000-0x0f8fff:EW,  
0x0f9000-0x0f9fff:EW, 0x0fa000-0x0fafff:S, 0x0fb000-0x0fbfff:S,  
0x0fc000-0x0fcfff:S, 0x0fd000-0x0fdfff:S, 0x0fe000-0x0fefff:S,  
0x0ff000-0x0fffff:EW
Erase/write done.
Verifying flash... VERIFIED.
Restoring PCI config space for 00:02:0 reg 0x43
Restoring PCI config space for 00:02:0 reg 0x41


tweakerO ~ # flashrom -V
flashrom v0.9.4-r1395 on Linux 2.6.36-gentoo-r8 (x86_64), built with  
libpci 3.1.7, GCC 4.4.5, little endian
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OS timer resolution is 1 usecs, 594M loops  
per second, 10 myus = 11 us, 100 myus = 101 us, 1000 myus = 1009 us,  
10000 myus = 10007 us, 4 myus = 5 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: "empty"
DMI string system-product-name: "empty"
DMI string system-version: "empty"
DMI string baseboard-manufacturer: "TYAN Computer Corporation"
DMI string baseboard-product-name: "S3992"
DMI string baseboard-version: "empty"
DMI string chassis-type: "Desktop"
Found chipset "Broadcom HT-1000" with PCI ID 1166:0205. Enabling flash  
write... OK.
This chipset supports the following protocols: Non-SPI.
Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for EMST F49B002UA, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0x52,  
id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0x52,  
id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0x52,  
id2 0xdf
Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0x52,  
id2 0xdf
Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0x52,  
id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1  
0x58, id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1  
0x52, id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1  
0x52, id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1  
0x52, id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1  
0x52, id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x52, id2 0xdf,  
id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0xff,  
id2 0xff, id1 parity violation, id1 is normal flash content, id2 is  
normal flash content
Probing for Macronix MX29F002B, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29F002T, 256 kB: probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0x52,  
id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0x52,  
id2 0xdf, id1 is normal flash content, id2 is normal flash content
Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1  
0xbf, id2 0x5b
Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0x58,  
id2 0x0b, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing  
information, using default 10mS/40uS. probe_jedec_common: id1 0xbf,  
id2 0x5b
Found SST flash chip "SST49LF080A" (1024 kB, LPC) at physical address  
0xfff00000.
Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0x52, id2 0xdf
Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0x52, id2 0xdf
Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0xff, id2  
0xff, id1 parity violation, id1 is normal flash content, id2 is normal  
flash content
Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0x52, id2  
0xdf, id1 is normal flash content, id2 is normal flash content
Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0x91, id2  
0x7a, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x52, id2 0xdf,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x52, id2 0xdf,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x58, id2 0x0b,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x52, id2 0xdf,  
id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0xff, id2 0xff,  
id1 parity violation, id1 is normal flash content, id2 is normal flash  
content
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0x58, id2  
0x0b, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB:  
Old Winbond W29* probe method disabled because the probing sequence  
puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/ 
W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip.
Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB:  
probe_jedec_common: id1 0xbf, id2 0x5b
Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common:  
id1 0xbf, id2 0x5b
Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0xbf, id2  
0x5b
Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf,  
id2 0x5b
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common:  
id1 0xbf, id2 0x5b
No operations were specified.
Restoring PCI config space for 00:02:0 reg 0x43
Restoring PCI config space for 00:02:0 reg 0x41


tweakerO ~ # lspci -nnvvxxx
00:01.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge  
[1166:0036] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=02, sec-latency=64
	I/O behind bridge: 0000a000-0000bfff
	Memory behind bridge: ff400000-ff4fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort-  
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [90] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
		Status: Dev=00:01.0 64bit- 133MHz- SCD- USC- SCO- SRD-
		Upstream: Capacity=0 CommitmentLimit=0
		Downstream: Capacity=0 CommitmentLimit=0
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] HyperTransport: Slave or Primary Interface
		Command: BaseUnitID=1 UnitCnt=3 MastHost- DefDir-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config 0: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
		Link Control 1: CFlE- CST- CFE- <LkFail- Init- EOC+ TXO+ <CRCErr=0
		Link Config 1: MLWI=8bit MLWO=8bit LWI=N/C LWO=N/C
		Revision ID: 0.00
	Capabilities: [d8] Subsystem: Gammagraphx, Inc. (or missing ID)  
Device [0000:0000]
00: 66 11 36 00 07 00 10 00 00 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 01 02 40 a1 b1 00 24
20: 40 ff 40 ff f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 90 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 00 00 00 01 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 c0 74 00 c0
60: e0 70 38 1c 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 01 04 08 00 01 08 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 07 a0 c3 00 08 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 08 d8 61 00 20 00 00 00 c0 00 00 77 00 05 75 00
c0: 02 00 35 00 00 00 00 00 00 00 00 00 0c 05 03 03
d0: 00 00 00 00 e0 0f 04 00 0d 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 80 00 40 00 04 00 00 00 00 00 00 00 00 00

00:02.0 Host bridge [0600]: Broadcom BCM5785 [HT1000] Legacy South  
Bridge [1166:0205]
	Subsystem: Broadcom Device [1166:0201]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
00: 66 11 05 02 07 01 00 02 00 00 00 06 00 40 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 01 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: a0 28 16 04 00 ff 00 00 07 00 00 00 10 02 10 04
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 8f c1 f3 1d 00 00 00 40 36 01 00 01
70: 0b 00 00 00 00 00 00 00 80 00 00 00 00 00 00 00
80: 80 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
90: 81 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:02.1 IDE interface [0101]: Broadcom BCM5785 [HT1000] IDE  
[1166:0214] (prog-if 8a [Master SecP PriP])
	Subsystem: Broadcom BCM5785 [HT1000] IDE [1166:0214]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4 [size=1]
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374 [size=1]
	Region 4: I/O ports at ffa0 [size=16]
	Capabilities: [b0] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 66 11 14 02 05 00 10 02 00 8a 01 01 10 40 80 00
10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 66 11 14 02
30: 00 00 00 00 b0 00 00 00 00 00 00 00 00 00 00 00
40: 5d 5d 5d 5d ff ff ff ff f0 f1 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 0f 04 03 00 00 00 00 00
60: 00 00 00 00 01 07 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 01 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:02.2 ISA bridge [0601]: Broadcom BCM5785 [HT1000] LPC [1166:0234]
	Subsystem: Broadcom Device [1166:0230]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
00: 66 11 34 02 07 01 00 02 00 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 30 02
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: ff ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11
90: 40 00 06 ff 00 ff 00 00 00 00 00 00 7c 64 00 00
a0: 00 00 00 00 03 03 02 ff 02 0b 30 0a ff ff 0f 00
b0: 03 a9 00 04 09 00 00 00 20 00 80 00 80 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:03.0 USB Controller [0c03]: Broadcom BCM5785 [HT1000] USB  
[1166:0223] (rev 01) (prog-if 10 [OHCI])
	Subsystem: Broadcom BCM5785 [HT1000] USB [1166:0223]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at ff6ec000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at d400 [size=256]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Kernel driver in use: ohci_hcd
00: 66 11 23 02 17 01 b0 02 01 10 03 0c 10 40 80 00
10: 00 c0 6e ff 01 d4 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 23 02
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 00 00
40: 80 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 00
e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:03.1 USB Controller [0c03]: Broadcom BCM5785 [HT1000] USB  
[1166:0223] (rev 01) (prog-if 10 [OHCI])
	Subsystem: Broadcom BCM5785 [HT1000] USB [1166:0223]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at ff6ed000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at d800 [size=256]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Kernel driver in use: ohci_hcd
00: 66 11 23 02 17 01 b0 02 01 10 03 0c 10 40 00 00
10: 00 d0 6e ff 01 d8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 23 02
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 00 00
40: 80 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 00
e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:03.2 USB Controller [0c03]: Broadcom BCM5785 [HT1000] USB  
[1166:0223] (rev 01) (prog-if 20 [EHCI])
	Subsystem: Broadcom BCM5785 [HT1000] USB [1166:0223]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 10
	Region 0: Memory at ff6ee000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at e800 [size=256]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot 
+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+
	Kernel driver in use: ehci_hcd
00: 66 11 23 02 17 01 b0 02 01 20 03 0c 10 40 00 00
10: 00 e0 6e ff 01 e8 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 66 11 23 02
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 00 00
40: 80 ff 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 20 20 00 00 00 20 00 00 00 20 00 00 00 20 00 00
70: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 01 00 00 00 00 00 08 c0 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 7e
e0: 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:04.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1  
Ethernet Pro 100 [8086:1229] (rev 10)
	Subsystem: Intel Corporation EtherExpress PRO/100 S Server Adapter  
[8086:1040]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at ff6eb000 (32-bit, non-prefetchable) [size=4K]
	Region 1: I/O ports at ec00 [size=64]
	Region 2: Memory at ff6a0000 (32-bit, non-prefetchable) [size=128K]
	Capabilities: [dc] Power Management version 2
		Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot 
+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=2 PME-
	Kernel driver in use: e100
00: 86 80 29 12 17 01 90 02 10 00 00 02 10 40 00 00
10: 00 b0 6e ff 01 ec 00 00 00 00 6a ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 40 10
30: 00 00 00 00 dc 00 00 00 00 00 00 00 09 01 08 38
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 22 fe
e0: 00 40 00 4b 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:06.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge  
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
	Capabilities: [90] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
		Status: Dev=00:06.0 64bit- 133MHz- SCD- USC- SCO- SRD-
		Upstream: Capacity=0 CommitmentLimit=0
		Downstream: Capacity=0 CommitmentLimit=0
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] HyperTransport: Slave or Primary Interface
		Command: BaseUnitID=6 UnitCnt=6 MastHost- DefDir-
		Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config 0: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
		Link Control 1: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
		Link Config 1: MLWI=8bit MLWO=8bit LWI=8bit LWO=8bit
		Revision ID: 0.00
00: 66 11 30 01 06 00 10 00 a3 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 03 03 40 f1 01 00 22
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 90 00 00 00 00 00 00 00 60 00 04 02
40: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 ca 53 00 c0
60: 0a 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 00 00 20 03 00 00 00 01 04 08 00 00 08 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 07 a0 c3 00 30 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 08 00 c6 00 20 00 11 11 20 00 00 00 00 06 75 00
c0: 02 05 35 00 00 00 00 00 00 00 00 00 0c 56 03 03
d0: 00 00 00 00 e0 0f 04 00 00 00 00 00 00 00 00 00
e0: 00 00 00 07 00 00 00 00 00 ff ca 20 00 00 00 00
f0: 00 00 00 40 00 00 00 00 00 00 00 00 00 00 00 00

00:07.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge  
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=64
	Memory behind bridge: ff500000-ff5fffff
	Prefetchable memory behind bridge: 00000000cfe00000-00000000cfefffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort-  
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [90] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
		Status: Dev=00:07.0 64bit- 133MHz- SCD- USC- SCO- SRD-
		Upstream: Capacity=0 CommitmentLimit=0
		Downstream: Capacity=0 CommitmentLimit=0
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
00: 66 11 30 01 06 00 10 00 a3 00 04 06 00 40 01 00
10: 00 00 00 00 00 00 00 00 00 04 04 40 f1 01 00 24
20: 50 ff 50 ff e1 cf e1 cf 00 00 00 00 00 00 00 00
30: 00 00 00 00 90 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 00 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 c8 00 00 c0
60: ca 60 30 18 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 00 00 20 01 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 07 a0 c3 00 38 00 00 00 00 00 00 00 00 00 00 00
a0: 08 00 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 08 00 c0 00 00 00 11 00 00 00 00 00 00 00 75 00
c0: 02 00 35 00 00 00 00 00 00 00 00 00 0c 00 03 03
d0: 00 00 00 00 e0 0f 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 ff 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:08.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express  
Bridge [1166:0132] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=05, subordinate=05, sec-latency=64
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <16us
			ExtTag- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #1, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0  
<4us, L1 <16us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive-  
BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-  
CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
00: 66 11 32 01 06 00 10 00 a3 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 05 05 40 f1 01 00 02
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 01 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0
60: 01 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 09 8f 84 34 00 00 00 00 01 00 00 00 00 00
80: 01 00 00 00 20 10 70 2b 72 0a 18 00 01 00 00 fb
90: 90 03 80 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 10 00 41 00 82 09 00 00 00 00 00 00 81 6c 02 01
c0: 08 00 81 00 00 00 08 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:09.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express  
Bridge [1166:0132] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=06, subordinate=06, sec-latency=64
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <16us
			ExtTag- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0  
<4us, L1 <16us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk- DLActive-  
BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-  
CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
00: 66 11 32 01 06 00 10 00 a3 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 06 06 40 f1 01 00 02
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 01 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0
60: 01 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 09 8f 84 34 00 00 00 00 01 00 00 00 00 00
80: 01 00 00 00 20 10 70 2b 72 0a 18 00 01 00 00 fb
90: 90 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 10 00 41 00 82 09 00 00 00 00 00 00 41 6c 02 02
c0: 08 00 01 00 00 00 10 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:0a.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express  
Bridge [1166:0132] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=07, subordinate=07, sec-latency=64
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <16us
			ExtTag- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #3, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0  
<4us, L1 <16us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk- DLActive-  
BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-  
CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
00: 66 11 32 01 06 00 10 00 a3 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 07 07 40 f1 01 00 02
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 01 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0
60: 01 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 09 8f 84 34 00 00 00 00 01 00 00 00 00 00
80: 01 00 00 00 20 10 70 2b 72 0a 18 00 01 00 00 fb
90: 90 03 80 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 10 00 41 00 82 09 00 00 00 00 00 00 81 6c 02 03
c0: 08 00 81 00 00 00 18 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:0b.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express  
Bridge [1166:0132] (rev a3) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=08, subordinate=08, sec-latency=64
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [a0] HyperTransport: MSI Mapping Enable+ Fixed-
		Mapping Address Base: 00000000fee00000
	Capabilities: [b0] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 512 bytes, PhantFunc 0, Latency L0s <4us, L1 <16us
			ExtTag- RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #4, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0  
<4us, L1 <16us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x0, TrErr- Train- SlotClk- DLActive-  
BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-  
CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
00: 66 11 32 01 06 00 10 00 a3 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 08 08 40 f1 01 00 02
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 60 00 04 00
40: 00 00 00 00 01 00 00 00 00 00 00 20 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0
60: 01 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00
70: 00 00 09 87 84 34 00 00 00 00 01 00 00 00 00 00
80: 01 00 00 00 20 10 70 2b 72 0a 18 00 01 00 00 fb
90: 90 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 08 b0 01 a8 00 00 e0 fe 00 00 00 00 00 00 00 00
b0: 10 00 41 00 82 09 00 00 00 00 00 00 41 6c 02 04
c0: 08 00 01 00 00 00 20 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:0c.0 VGA compatible controller [0300]: ATI Technologies Inc ES1000  
[1002:515e] (rev 02) (prog-if 00 [VGA controller])
	Subsystem: ATI Technologies Inc ES1000 [1002:515e]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping+ SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at e000 [size=256]
	Region 2: Memory at ff6f0000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at ff6c0000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 5e 51 87 01 90 02 02 00 00 03 10 40 00 00
10: 08 00 00 d8 01 e0 00 00 00 00 6f ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 5e 51
30: 00 00 6c ff 50 00 00 00 00 00 00 00 0b 01 08 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 02 10 5e 51
50: 01 00 02 06 00 00 00 00 02 50 20 00 00 02 00 2f
60: 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/ 
Opteron] HyperTransport Technology Configuration [1022:1100]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [80] HyperTransport: Host or Secondary Interface
		Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave-  
<EOCErr- DUL-
		Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0  
IsocEn- LSEn- ExtCTL- 64b-
		Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit  
DwFcInEn- LWO=16bit DwFcOutEn-
		Revision ID: 1.02
		Link Frequency: 1.0GHz
		Link Error: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+  
800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-  
ExtRS- UCnfE-
	Capabilities: [a0] HyperTransport: Host or Secondary Interface
		Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave-  
<EOCErr- DUL-
		Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0  
IsocEn- LSEn- ExtCTL- 64b-
		Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=N/C  
DwFcInEn- LWO=N/C DwFcOutEn-
		Revision ID: 1.02
		Link Frequency: 200MHz
		Link Error: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+  
800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-  
ExtRS- UCnfE-
	Capabilities: [c0] HyperTransport: Host or Secondary Interface
		Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave-  
<EOCErr- DUL-
		Link Control: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0  
IsocEn- LSEn- ExtCTL- 64b-
		Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=N/C  
DwFcInEn- LWO=N/C DwFcOutEn-
		Revision ID: 1.02
		Link Frequency: 200MHz
		Link Error: <Prot- <Ovfl- <EOC- CTLTm-
		Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+  
800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
		Feature Capability: IsocFC- LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-  
ExtRS- UCnfE-
00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
40: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
60: 00 00 01 00 e4 00 00 00 20 c8 0f 0f 2c 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 08 a0 01 21 20 00 11 11 22 06 75 80 02 00 00 00
90: 56 04 51 02 00 00 ff 00 07 00 00 00 00 00 00 00
a0: 08 c0 01 21 d0 00 11 77 22 00 75 80 02 00 00 00
b0: 79 ff 70 01 00 00 00 00 00 00 00 00 00 00 00 00
c0: 08 00 01 21 d0 00 11 77 22 00 75 80 02 00 00 00
d0: 60 c1 74 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/ 
Opteron] Address Map [1022:1101]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 03 00 00 00 00 00 3f 01 00 00 00 00 01 00 00 00
50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00
60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00
70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 03 0a 00 00 00 0b 00 00 03 00 c0 00 00 70 ff 00
c0: 13 10 00 00 00 f0 ff 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 03 00 00 ff 00 00 00 00 00 00 00 00 00 00 00 00
f0: 01 40 00 c0 00 00 00 00 00 00 00 00 00 00 00 00

00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/ 
Opteron] DRAM Controller [1022:1102]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
40: 01 00 00 00 01 02 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: e0 3d f8 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00
80: 06 00 00 00 00 00 00 00 24 a2 68 c3 20 13 13 00
90: 10 19 08 00 5a 80 00 a4 10 00 00 80 2c 00 00 00
a0: e9 02 00 c3 00 00 00 00 00 00 00 00 00 00 00 00
b0: 44 2e 99 87 9d 00 00 00 d9 ff 0e 2b bc e8 04 80
c0: 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 4d 96 9b 64 cb 9f c1 80 d6 c2 b0 4c 1c 89 9a 72
e0: 0f 82 dd 72 a5 9a 40 a0 6e e0 90 0f 1c 41 9b 3b
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/ 
Opteron] Miscellaneous Control [1022:1103]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: [f0] Secure device <?>
00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00
40: ff 3b 04 00 44 00 d0 0a 00 00 00 00 00 00 00 00
50: f0 ff ff 3f 01 00 00 00 00 00 00 00 c0 82 06 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 11 01 02 51 11 80 00 50 00 38 00 08 2a 22 00 00
80: 00 00 07 23 13 21 13 00 00 00 00 00 00 00 00 00
90: 03 00 00 00 10 00 00 00 00 aa 3e 01 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 0f 00 00 00 00 00 00 00 00 00 70 ff 23
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 07 a7 e2 04 10 27 a0 20 25 26 25 00
e0: 00 00 00 00 20 18 53 00 1b 17 00 00 00 00 00 00
f0: 0f 00 10 00 00 04 00 00 02 00 00 00 12 0f 04 00

01:0d.0 PCI bridge [0604]: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge  
[1166:0104] (rev c0) (prog-if 00 [Normal decode])
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-  
Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64, Cache Line Size: 64 bytes
	Bus: primary=01, secondary=02, subordinate=02, sec-latency=64
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
	Capabilities: [90] PCI-X bridge device
		Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
		Status: Dev=01:0d.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
		Upstream: Capacity=8 CommitmentLimit=8
		Downstream: Capacity=8 CommitmentLimit=8
	Capabilities: [88] Subsystem: Device [daef:fdae]
00: 66 11 04 01 16 00 30 02 c0 00 04 06 10 40 01 00
10: 00 00 00 00 00 00 00 00 01 02 02 40 f1 01 20 22
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 90 00 00 00 00 00 00 00 00 00 04 02
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 c0 13 00 c0
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 04 00 00 00 00 00 00 0d 00 00 00 ef da ae fd
90: 07 88 03 00 68 01 03 00 08 00 08 00 08 00 08 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01:0e.0 IDE interface [0101]: Broadcom BCM5785 [HT1000] SATA (PATA/IDE  
Mode) [1166:024b] (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: Broadcom BCM5785 [HT1000] SATA (PATA/IDE Mode) [1166:024b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at bc00 [size=8]
	Region 1: I/O ports at b880 [size=4]
	Region 2: I/O ports at b800 [size=8]
	Region 3: I/O ports at b480 [size=4]
	Region 4: I/O ports at b400 [size=16]
	Region 5: Memory at ff4fe000 (32-bit, non-prefetchable) [size=8K]
	Expansion ROM at ff4c0000 [disabled] [size=128K]
	Capabilities: [60] PCI-X non-bridge device
		Command: DPERE- ERO- RBC=512 OST=8
		Status: Dev=01:0e.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512  
DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
	Capabilities: [90] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Kernel driver in use: sata_svw
00: 66 11 4b 02 07 01 10 02 00 8f 01 01 00 40 80 00
10: 01 bc 00 00 81 b8 00 00 01 b8 00 00 81 b4 00 00
20: 01 b4 00 00 00 e0 4f ff 00 00 00 00 66 11 4b 02
30: 00 00 4c ff 60 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 07 90 40 00 70 01 03 0a 00 00 00 00 00 00 00 00
70: 28 00 00 00 00 00 00 00 84 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 01 a0 02 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

01:0e.1 IDE interface [0101]: Broadcom BCM5785 [HT1000] SATA (PATA/IDE  
Mode) [1166:024b] (prog-if 8f [Master SecP SecO PriP PriO])
	Subsystem: Broadcom BCM5785 [HT1000] SATA (PATA/IDE Mode) [1166:024b]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Interrupt: pin A routed to IRQ 11
	Region 0: I/O ports at b080 [size=8]
	Region 1: I/O ports at b000 [size=4]
	Region 2: I/O ports at ac00 [size=8]
	Region 3: I/O ports at a880 [size=4]
	Region 4: I/O ports at a800 [size=16]
	Capabilities: [60] PCI-X non-bridge device
		Command: DPERE- ERO- RBC=512 OST=8
		Status: Dev=01:0e.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512  
DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
	Capabilities: [90] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA  
PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [a0] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
00: 66 11 4b 02 07 01 30 02 00 8f 01 01 00 40 80 00
10: 81 b0 00 00 01 b0 00 00 01 ac 00 00 81 a8 00 00
20: 01 a8 00 00 00 00 00 00 00 00 00 00 66 11 4b 02
30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00
40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 07 90 40 00 70 01 03 0a 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 01 a0 02 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

04:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme  
BCM5780 Gigabit Ethernet [14e4:166a] (rev 03)
	Subsystem: Broadcom Corporation NetXtreme BCM5780 Gigabit Ethernet  
[14e4:166a]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (16000ns min), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 26
	Region 0: Memory at ff5d0000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at ff5c0000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] PCI-X non-bridge device
		Command: DPERE- ERO+ RBC=512 OST=1
		Status: Dev=04:04.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048  
DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot 
+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
		Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
		Read-only fields:
			[PN] Part number: BCM95780
			[EC] Engineering changes: 106679-15
			[SN] Serial number: 0123456789
			[MN] Manufacture ID: 31 34 65 34
			[RV] Reserved: checksum bad, 28 byte(s) reserved
		Read/write fields:
			[YA] Asset tag: XYZ01234567
			[RW] Read-write area: 107 byte(s) free
		End
	Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
		Address: bf7f5badf77cbd10  Data: 5ebb
	Kernel driver in use: tg3
00: e4 14 6a 16 06 01 b0 02 03 00 00 02 10 40 80 00
10: 04 00 5d ff 00 00 00 00 04 00 5c ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 6a 16
30: 00 00 00 00 40 00 00 00 00 00 00 00 07 01 40 00
40: 07 48 02 00 20 04 43 04 01 50 02 c0 00 20 00 64
50: 03 58 ac 00 00 00 00 78 05 00 86 00 10 bd 7c f7
60: ad 5b 7f bf bb 5e 00 00 9a 02 03 80 00 40 14 76
70: 8a 12 00 00 a7 00 00 00 50 00 00 00 00 00 00 00
80: 03 58 fc 80 4f 51 8a 5f 34 00 00 00 fe 50 08 04
90: 01 ba 00 01 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

04:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme  
BCM5780 Gigabit Ethernet [14e4:166a] (rev 03)
	Subsystem: Broadcom Corporation NetXtreme BCM5780 Gigabit Ethernet  
[14e4:166a]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-  
Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-  
<TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (16000ns min), Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 27
	Region 0: Memory at ff5f0000 (64-bit, non-prefetchable) [size=64K]
	Region 2: Memory at ff5e0000 (64-bit, non-prefetchable) [size=64K]
	Capabilities: [40] PCI-X non-bridge device
		Command: DPERE- ERO+ RBC=512 OST=1
		Status: Dev=04:04.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048  
DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
	Capabilities: [48] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot 
+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
	Capabilities: [50] Vital Product Data
		Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
		Read-only fields:
			[PN] Part number: BCM95780
			[EC] Engineering changes: 106679-15
			[SN] Serial number: 0123456789
			[MN] Manufacture ID: 31 34 65 34
			[RV] Reserved: checksum bad, 28 byte(s) reserved
		Read/write fields:
			[YA] Asset tag: XYZ01234567
			[RW] Read-write area: 107 byte(s) free
		End
	Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
		Address: ffbf8bfffff93bd8  Data: dd1b
	Kernel driver in use: tg3
00: e4 14 6a 16 06 01 b0 02 03 00 00 02 10 40 80 00
10: 04 00 5f ff 00 00 00 00 04 00 5e ff 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 e4 14 6a 16
30: 00 00 00 00 40 00 00 00 00 00 00 00 05 02 40 00
40: 07 48 02 00 21 04 43 04 01 50 02 c0 00 20 00 64
50: 03 58 cc 00 00 00 00 78 05 00 86 00 d8 3b f9 ff
60: ff 8b bf ff 1b dd 00 00 9a 02 03 80 00 40 14 76
70: 8a 12 00 00 a7 00 00 00 50 00 00 00 00 00 00 00
80: 03 58 fc 80 87 e6 52 9f 34 00 00 00 fe 50 08 04
90: 01 ba 00 09 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

tweakerO ~ #


tweakerO superiotool # ./superiotool -deV
superiotool r
Probing for ALi Super I/O at 0x3f0...
   Failed. Returned data: id=0xffff, rev=0xff
Probing for ALi Super I/O at 0x370...
   Failed. Returned data: id=0xffff, rev=0xff
Probing for Fintek Super I/O at 0x2e...
   Failed. Returned data: vid=0x0040, id=0x19ee
Probing for Fintek Super I/O at 0x4e...
   Failed. Returned data: vid=0xffff, id=0xffff
Probing for Fintek Super I/O at 0x2e...
   Failed. Returned data: vid=0x0040, id=0x19ee
Probing for Fintek Super I/O at 0x4e...
   Failed. Returned data: vid=0xffff, id=0xffff
Probing for ITE Super I/O (init=standard) at 0x25e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8502e) at 0x25e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x25e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x25e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x25e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=standard) at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x0
Probing for ITE Super I/O (init=it8502e) at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x0
Probing for ITE Super I/O (init=it8761e) at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x0
Probing for ITE Super I/O (init=it8228e) at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x0
Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x0
Probing for ITE Super I/O (init=standard) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8502e) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...
   Failed. Returned data: id=0xffff, rev=0xf
Probing for NSC Super I/O at 0x2e...
Found NSC PC8741x (sid=0xee, srid=0x09) at 0x2e
Register dump:
idx 20 21 22 23 24 25 26 27  28 29 2a 2b 2c 2d 2e 2f
val ee 19 a0 40 00 71 00 09  00 1c 00 00 00 00 00 00
def ee 11 20 MM MM MM 00 NA  00 MM 00 RR RR RR RR RR
LDN 0x00 (Floppy)
idx 30 60 61 70 71 74 75 f0  f1
val 00 00 00 00 03 04 04 24  00
def 00 03 f2 06 03 02 04 24  00
LDN 0x01 (Parallel port)
idx 30 60 61 70 71 74 75 f0
val 00 02 78 07 02 04 04 f2
def 00 02 78 07 02 04 04 f2
LDN 0x02 (COM2)
idx 30 60 61 70 71 74 75 f0
val 01 02 f8 03 03 04 04 02
def 00 02 f8 03 03 04 04 02
LDN 0x03 (COM1)
idx 30 60 61 70 71 74 75 f0
val 01 03 f8 04 03 04 04 02
def 00 03 f8 04 03 04 04 02
LDN 0x04 (System wake-up control (SWC))
idx 30 60 61 62 63 64 65 66  67 70 71 74 75
val 01 05 20 05 40 05 44 05  50 00 03 04 04
def 00 00 00 00 00 00 00 00  00 00 03 04 04
LDN 0x05 (Mouse)
idx 30 70 71 74 75
val 01 0c 02 04 04
def 00 0c 02 04 04
LDN 0x06 (Keyboard)
idx 30 60 61 62 63 70 71 74  75 f0
val 01 00 60 00 64 01 02 04  04 40
def 00 00 60 00 64 01 02 04  04 40
LDN 0x07 (GPIO)
idx 30 60 61 70 71 74 75 f0  f1 f2 f3
val 01 06 00 00 03 04 04 44  03 00 00
def 00 00 00 00 03 04 04 00  MM 01 00
LDN 0x0f (X-Bus)
idx 30 60 61 70 71 74 75 f0  f1 f2 f3 f4 f5 f6 f7 f8  f9 fa fb fc
val 00 00 00 00 00 04 04 00  00 00 00 00 00 00 00 00  00 00 00 00
def 00 00 00 00 00 04 04 00  00 00 00 00 00 00 00 00  00 00 00 00
LDN 0x10 (Real-time clock (RTC))
idx 30 60 61 62 63 70 71 74  75 f0 f1 f2 f3
val 01 00 70 00 72 08 00 04  04 00 7d 7e 32
def 00 00 70 00 72 08 00 04  04 00 00 00 00
Probing for NSC Super I/O at 0x4e...
   Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x15c...
   Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x164e...
   Failed. Returned data: port=0xff, port+1=0xff
Probing for Nuvoton Super I/O at 0x164e...
   Failed. Returned data: chip_id=0xffff
Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e...
   Failed. Returned data: sid=0xff, id=0xffff, rev=0x00
Probing for Nuvoton Super I/O at 0x2e...
   Failed. Returned data: chip_id=0xee19
Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e...
   Failed. Returned data: sid=0xee, id=0xee19, rev=0x00
Probing for Nuvoton Super I/O at 0x4e...
   Failed. Returned data: chip_id=0xffff
Probing for Nuvoton Super I/O (sid=0xfc) at 0x4e...
   Failed. Returned data: sid=0xff, id=0xffff, rev=0x00
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
   Failed. Returned data: id=0xee, rev=0x19
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
   Failed. Returned data: id=0x00, rev=0x00
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
   Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
   Failed. Returned data: id=0xff, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x2e...
   Failed. Returned data: id/oldid=0xee/0x00, rev=0x19
Probing for Winbond Super I/O (init=0x89) at 0x2e...
   Failed. Returned data: id/oldid=0xee/0x00, rev=0x19
Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
   Failed. Returned data: id/oldid=0xee/0x00, rev=0x19
Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
   Failed. Returned data: id/oldid=0xee/0x00, rev=0x19
Probing for Winbond Super I/O (init=0x88) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
   Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for VIA Super I/O at 0x3f0...
   PCI device 1106:0686 not found.
Probing for Server Engines Super I/O at 0x2e...
   Failed. Returned data: id=0xee19, rev=0x00





More information about the flashrom mailing list