[flashrom] [commit] r1466 - trunk
repository service
svn at flashrom.org
Mon Nov 14 14:00:12 CET 2011
Author: stefanct
Date: Mon Nov 14 14:00:12 2011
New Revision: 1466
URL: http://flashrom.org/trac/flashrom/changeset/1466
Log:
board_enable.c: Make it8712f_gpio_set generic
This looks suspiciously like intel_ich_gpio_set.
Based on that, add board enables for the ASUS P5N-D and P5N-E SLI.
This was tested by Guillaume Poirier-Morency on a P5N-D:
http://www.flashrom.org/pipermail/flashrom/2011-August/007706.html
Signed-off-by: Joshua Roys <roysjosh at gmail.com>
Small changes were also contributed and
Signed-off-by: Stefan Tauner <stefan.tauner at student.tuwien.ac.at>
Acked-by: Stefan Tauner <stefan.tauner at student.tuwien.ac.at>
Modified:
trunk/board_enable.c
trunk/print.c
Modified: trunk/board_enable.c
==============================================================================
--- trunk/board_enable.c Mon Nov 14 00:03:30 2011 (r1465)
+++ trunk/board_enable.c Mon Nov 14 14:00:12 2011 (r1466)
@@ -1917,54 +1917,90 @@
}
/*
- * General routine for raising/dropping GPIO lines on the ITE IT8712F.
- * There is only some limited checking on the port numbers.
+ * General routine for raising/dropping GPIO lines on the ITE IT87xx.
*/
-static int it8712f_gpio_set(unsigned int line, int raise)
+static int it87_gpio_set(unsigned int gpio, int raise)
{
+ int allowed, sio;
unsigned int port;
- uint16_t id, base;
+ uint16_t base, sioport;
uint8_t tmp;
- port = line / 10;
- port--;
- line %= 10;
-
- /* Check line */
- if ((port > 4) || /* also catches unsigned -1 */
- ((port < 4) && (line > 7)) || ((port == 4) && (line > 5))) {
- msg_perr("\nERROR: Unsupported IT8712F GPIO line %02d.\n", line);
+ /* IT87 GPIO configuration table */
+ static const struct it87cfg {
+ uint16_t id;
+ uint8_t base_reg;
+ uint32_t bank0;
+ uint32_t bank1;
+ uint32_t bank2;
+ } it87_gpio_table[] = {
+ {0x8712, 0x62, 0xCFF3FC00, 0x00FCFF3F, 0},
+ {0x8718, 0x62, 0xCFF37C00, 0xF3FCDF3F, 0x0000000F},
+ {0, 0, 0, 0, 0} /* end marker */
+ };
+ const struct it87cfg *cfg = NULL;
+
+ /* Find the Super I/O in the probed list */
+ for (sio = 0; sio < superio_count; sio++) {
+ int i;
+ if (superios[sio].vendor != SUPERIO_VENDOR_ITE)
+ continue;
+
+ /* Is this device in our list? */
+ for (i = 0; it87_gpio_table[i].id; i++)
+ if (superios[sio].model == it87_gpio_table[i].id) {
+ cfg = &it87_gpio_table[i];
+ goto found;
+ }
+ }
+
+ if (cfg == NULL) {
+ msg_perr("\nERROR: No IT87 Super I/O GPIO configuration "
+ "found.\n");
return -1;
}
- /* Find the IT8712F. */
- enter_conf_mode_ite(0x2E);
- id = (sio_read(0x2E, 0x20) << 8) | sio_read(0x2E, 0x21);
- exit_conf_mode_ite(0x2E);
+found:
+ /* Check whether the gpio is allowed. */
+ if (gpio < 32)
+ allowed = (cfg->bank0 >> gpio) & 0x01;
+ else if (gpio < 64)
+ allowed = (cfg->bank1 >> (gpio - 32)) & 0x01;
+ else if (gpio < 96)
+ allowed = (cfg->bank2 >> (gpio - 64)) & 0x01;
+ else
+ allowed = 0;
- if (id != 0x8712) {
- msg_perr("\nERROR: IT8712F Super I/O not found.\n");
+ if (!allowed) {
+ msg_perr("\nERROR: IT%02X does not allow setting GPIO%02u.\n",
+ cfg->id, gpio);
return -1;
}
- /* Get the GPIO base */
- enter_conf_mode_ite(0x2E);
- sio_write(0x2E, 0x07, 0x07);
- base = (sio_read(0x2E, 0x62) << 8) | sio_read(0x2E, 0x63);
- exit_conf_mode_ite(0x2E);
+ /* Read the Simple I/O Base Address Register */
+ sioport = superios[sio].port;
+ enter_conf_mode_ite(sioport);
+ sio_write(sioport, 0x07, 0x07);
+ base = (sio_read(sioport, cfg->base_reg) << 8) |
+ sio_read(sioport, cfg->base_reg + 1);
+ exit_conf_mode_ite(sioport);
if (!base) {
- msg_perr("\nERROR: Failed to read IT8712F Super I/O GPIO"
- " Base.\n");
+ msg_perr("\nERROR: Failed to read IT87 Super I/O GPIO Base.\n");
return -1;
}
- /* Set GPIO. */
+ msg_pdbg("Using IT87 GPIO base 0x%04x\n", base);
+
+ port = gpio / 10 - 1;
+ gpio %= 10;
+
+ /* set GPIO. */
tmp = INB(base + port);
if (raise)
- tmp |= 1 << line;
+ tmp |= 1 << gpio;
else
- tmp &= ~(1 << line);
+ tmp &= ~(1 << gpio);
OUTB(tmp, base + port);
return 0;
@@ -1975,9 +2011,19 @@
* - ASUS A7V600-X: VIA KT600 + VT8237 + IT8712F
* - ASUS A7V8X-X: VIA KT400 + VT8235 + IT8712F
*/
-static int it8712f_gpio3_1_raise(void)
+static int it8712f_gpio31_raise(void)
+{
+ return it87_gpio_set(32, 1);
+}
+
+/*
+ * Suited for:
+ * - ASUS P5N-D: NVIDIA MCP51 + IT8718F
+ * - ASUS P5N-E SLI: NVIDIA MCP51 + IT8718F
+ */
+static int it8718f_gpio63_raise(void)
{
- return it8712f_gpio_set(32, 1);
+ return it87_gpio_set(63, 1);
}
#endif
@@ -2047,11 +2093,11 @@
{0x1039, 0x0741, 0x1849, 0x0741, 0x1039, 0x5513, 0x1849, 0x5513, "^K7S41GX$", NULL, NULL, P3, "ASRock", "K7S41GX", 0, OK, w836xx_memw_enable_2e},
{0x8086, 0x24D4, 0x1849, 0x24D0, 0x8086, 0x24D5, 0x1849, 0x9739, NULL, NULL, NULL, P3, "ASRock", "P4i65GV", 0, OK, intel_ich_gpio23_raise},
{0x8086, 0x2570, 0x1849, 0x2570, 0x8086, 0x24d3, 0x1849, 0x24d0, NULL, NULL, NULL, P3, "ASRock", "775i65G", 0, OK, intel_ich_gpio23_raise},
- {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3065, 0x1043, 0x80ED, NULL, NULL, NULL, P3, "ASUS", "A7V600-X", 0, OK, it8712f_gpio3_1_raise},
+ {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3065, 0x1043, 0x80ED, NULL, NULL, NULL, P3, "ASUS", "A7V600-X", 0, OK, it8712f_gpio31_raise},
{0x1106, 0x3177, 0x1043, 0x80A1, 0x1106, 0x3205, 0x1043, 0x8118, NULL, NULL, NULL, P3, "ASUS", "A7V8X-MX SE", 0, OK, w836xx_memw_enable_2e},
{0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x808C, NULL, NULL, NULL, P3, "ASUS", "A7V8X", 0, OK, it8703f_gpio51_raise},
{0x1106, 0x3099, 0x1043, 0x807F, 0x1106, 0x3147, 0x1043, 0x808C, NULL, NULL, NULL, P3, "ASUS", "A7V333", 0, OK, it8703f_gpio51_raise},
- {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x80A1, NULL, NULL, NULL, P3, "ASUS", "A7V8X-X", 0, OK, it8712f_gpio3_1_raise},
+ {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x80A1, NULL, NULL, NULL, P3, "ASUS", "A7V8X-X", 0, OK, it8712f_gpio31_raise},
{0x1002, 0x4372, 0x103c, 0x2a26, 0x1002, 0x4377, 0x103c, 0x2a26, NULL, NULL, NULL, P3, "ASUS", "A8AE-LE", 0, OK, amd_sbxxx_gpio9_raise},
{0x8086, 0x27A0, 0x1043, 0x1287, 0x8086, 0x27DF, 0x1043, 0x1287, "^A8J", NULL, NULL, P3, "ASUS", "A8Jm", 0, NT, intel_ich_gpio34_raise},
{0x10DE, 0x0260, 0x103C, 0x2A34, 0x10DE, 0x0264, 0x103C, 0x2A34, "NODUSM3", NULL, NULL, P3, "ASUS", "A8M2N-LA (NodusM3-GL8E)", 0, OK, nvidia_mcp_gpio0_raise},
@@ -2084,6 +2130,8 @@
{0x8086, 0x27b8, 0x1043, 0x2a22, 0x8086, 0x2770, 0x1043, 0x2a22, "^P5LP-LE$", NULL, NULL, P3, "ASUS", "P5LP-LE (Epson OEM)", 0, OK, intel_ich_gpio34_raise},
{0x8086, 0x27da, 0x1043, 0x8179, 0x8086, 0x27b8, 0x1043, 0x8179, "^P5LD2$", NULL, NULL, P3, "ASUS", "P5LD2", 0, NT, intel_ich_gpio16_raise},
{0x10DE, 0x0030, 0x1043, 0x818a, 0x8086, 0x100E, 0x1043, 0x80EE, NULL, NULL, NULL, P3, "ASUS", "P5ND2-SLI Deluxe", 0, OK, nvidia_mcp_gpio10_raise},
+ {0x10DE, 0x0260, 0x1043, 0x81BC, 0x10DE, 0x026C, 0x1043, 0x829E, "^P5N-D$", NULL, NULL, P3, "ASUS", "P5N-D", 0, OK, it8718f_gpio63_raise},
+ {0x10DE, 0x0260, 0x1043, 0x81BC, 0x10DE, 0x026C, 0x1043, 0x8249, "^P5N-E SLI$",NULL, NULL, P3, "ASUS", "P5N-E SLI", 0, NT, it8718f_gpio63_raise},
{0x8086, 0x24dd, 0x1043, 0x80a6, 0x8086, 0x2570, 0x1043, 0x8157, NULL, NULL, NULL, P3, "ASUS", "P5PE-VM", 0, OK, intel_ich_gpio21_raise},
{0x10b7, 0x9055, 0x1028, 0x0082, 0x8086, 0x7190, 0, 0, NULL, NULL, NULL, P3, "Dell", "OptiPlex GX1", 0, OK, intel_piix4_gpo30_lower},
{0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, NULL, P3, "Dell", "PowerEdge 1850", 0, OK, intel_ich_gpio23_raise},
Modified: trunk/print.c
==============================================================================
--- trunk/print.c Mon Nov 14 00:03:30 2011 (r1465)
+++ trunk/print.c Mon Nov 14 14:00:12 2011 (r1466)
@@ -661,6 +661,8 @@
B("ASUS", "P5LP-LE (Epson OEM)", 1, NULL, "This is an OEM board from Epson (e.g. Endeavor MT7700)."),
B("ASUS", "P5LP-LE", 0, NULL, "This designation is used for OEM boards from HP, Epson and maybe others. The HP names vary and not all of them have been tested yet. Please report any success or failure, thanks."),
B("ASUS", "P5N-E SLI", 0, "http://www.asus.com/product.aspx?P_ID=KyHOsOKWujC2QguJ", "Needs a board enable (http://patchwork.coreboot.org/patch/3298/)."),
+ B("ASUS", "P5N-D", 1, "http://www.asus.com/Motherboards/Intel_Socket_775/P5ND/", NULL),
+ B("ASUS", "P5N-E SLI", 0, "http://www.asus.com/Motherboards/Intel_Socket_775/P5NE_SLI/", "Untested board enable."),
B("ASUS", "P5N32-E SLI", 1, "http://www.asus.com/product.aspx?P_ID=vBZLIBtPzYB2bLcb", NULL),
B("ASUS", "P5ND2-SLI Deluxe", 1, "http://www.asus.com/product.aspx?P_ID=WY7XroDuUImVbgp5", NULL),
B("ASUS", "P5PE-VM", 1, "http://www.asus.com/product.aspx?P_ID=k3h0ZFVu9Lo1dUvk", NULL),
More information about the flashrom
mailing list