[flashrom] About my motherboard.

Mon May 10 01:05:07 CEST 2010

Hi, I have a laptop with sis chipset and i decided to give you some
information about it if it would help.
Below are the outputs from lspci, flashrom and superiotool. It seem it
hasn't any significant information (except being unsupported).
I hope this helps.
Regards,
Bugra

lspci -nnvvvxxx

00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 671MX
[1039:0671]
        Subsystem: Fujitsu Siemens Computers Device
[1734:1125]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
        Latency:
32

        Region 0: Memory at d0000000 (32-bit, non-prefetchable)
[size=64M]
        Capabilities: <access
denied>

        Kernel driver in use:
agpgart-sis

00: 39 10 71 06 07 00 10 22 00 00 00 06 00 20 00
00
10: 00 00 00 d0 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25
11
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00
00

00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SiS AGP Port
(virtual PCI-to-PCI bridge) [1039:0003] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 16
bytes

        Bus: primary=00, secondary=01, subordinate=01,
sec-latency=0

        I/O behind bridge:
00009000-00009fff

        Memory behind bridge:
d4000000-d40fffff

        Prefetchable memory behind bridge:
c0000000-cfffffff

        Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset-
FastB2B-

                PriDiscTmr- SecDiscTmr- DiscTmrStat-
DiscTmrSERREn-

        Kernel modules:
shpchp

00: 39 10 03 00 07 00 20 00 00 00 04 06 04 00 01
00

10: 00 00 00 00 00 00 00 00 00 01 01 00 90 90 20
20

20: 00 d4 00 d4 00 c0 f0 cf 00 00 00 00 00 00 00
00

30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 0c
00

00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS968 [MuTIOL
Media IO] [1039:0968] (rev 01)
        Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency:
0

00: 39 10 68 09 0f 00 00 02 01 00 01 06 00 00 80
00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00

00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE]
[1039:5513] (rev 01) (prog-if 80 [Master])
        Subsystem: Silicon Integrated Systems [SiS] SiS5513 EIDE Controller
(A,B step) [1039:5513]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency:
128

        Interrupt: pin ? routed to IRQ
16

        Region 0: I/O ports at 01f0
[size=8]

        Region 1: I/O ports at 03f4
[size=1]

        Region 2: I/O ports at 0170
[size=8]

        Region 3: I/O ports at 0374
[size=1]

        Region 4: I/O ports at 1000
[size=16]

        Capabilities: <access
denied>

        Kernel driver in use:
pata_sis

        Kernel modules:
pata_sis

00: 39 10 13 55 05 00 10 02 01 80 01 01 00 80 00
00
10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00
00
20: 01 10 00 00 00 00 00 00 00 00 00 00 39 10 13
55
30: 00 00 00 00 58 00 00 00 00 00 00 00 00 00 00
00

00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1
Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
        Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller
[1039:7001]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (20000ns
max)

        Interrupt: pin A routed to IRQ
20

        Region 0: Memory at d4204000 (32-bit, non-prefetchable)
[size=4K]
        Kernel driver in use:
ohci_hcd

00: 39 10 01 70 17 00 80 02 0f 10 03 0c 00 20 80
00
10: 00 40 20 d4 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 01
70
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00
50

00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1
Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
        Subsystem: Silicon Integrated Systems [SiS] USB 1.1 Controller
[1039:7001]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (20000ns
max)

        Interrupt: pin B routed to IRQ
21

        Region 0: Memory at d4205000 (32-bit, non-prefetchable)
[size=4K]
        Kernel driver in use:
ohci_hcd

00: 39 10 01 70 17 00 80 02 0f 10 03 0c 00 20 00
00
10: 00 50 20 d4 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 01
70
30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 02 00
50

00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0
Controller [1039:7002] (prog-if 20 [EHCI])
        Subsystem: Fujitsu Siemens Computers Device
[1734:1125]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 32 (20000ns max), Cache Line Size: 32
bytes
        Interrupt: pin C routed to IRQ
22
        Region 0: Memory at d4206000 (32-bit, non-prefetchable)
[size=4K]
        Capabilities: <access
denied>

        Kernel driver in use:
ehci_hcd

00: 39 10 02 70 06 00 90 02 00 20 03 0c 08 20 00
00
10: 00 60 20 d4 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25
11
30: 00 00 00 00 50 00 00 00 00 00 00 00 07 03 00
50

00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191
Gigabit Ethernet Adapter [1039:0191] (rev 02)
        Subsystem: Fujitsu Siemens Computers Device
[1734:1125]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency:
0

        Interrupt: pin A routed to IRQ
19

        Region 0: Memory at d4407000 (32-bit, non-prefetchable)
[size=128]
        Region 1: I/O ports at 1080
[size=128]

        Capabilities: <access
denied>

        Kernel driver in use:
sis190

        Kernel modules:
sis190

00: 39 10 91 01 07 00 10 02 02 00 00 02 00 00 00
00
10: 00 70 40 d4 81 10 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25
11
30: 00 00 00 00 40 00 00 00 00 00 00 00 03 01 00
00

00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] SATA
Controller / IDE mode [1039:1183] (rev 03) (prog-if 8f [Master SecP SecO
PriP PriO])
        Subsystem: Silicon Integrated Systems [SiS] SATA Controller / IDE
mode
[1039:1183]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
INTx-
        Latency:
32

        Interrupt: pin A routed to IRQ
17

        Region 0: I/O ports at 1058
[size=8]

        Region 1: I/O ports at 104c
[size=4]

        Region 2: I/O ports at 1050
[size=8]

        Region 3: I/O ports at 1048
[size=4]

        Region 4: I/O ports at 1020
[size=16]

        Capabilities: <access
denied>

        Kernel driver in use:
sata_sis

        Kernel modules:
sata_sis

00: 39 10 83 11 05 00 10 02 03 8f 01 01 00 20 00
00

10: 59 10 00 00 4d 10 00 00 51 10 00 00 49 10 00
00

20: 21 10 00 00 00 00 00 00 00 00 00 00 39 10 83
11

30: 00 00 00 00 58 00 00 00 00 00 00 00 05 01 00
00

00:06.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI
bridge [1039:000a] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 16
bytes

        Bus: primary=00, secondary=02, subordinate=02,
sec-latency=0
        I/O behind bridge:
0000f000-00000fff

        Memory behind bridge:
d4100000-d41fffff

        Prefetchable memory behind bridge:
00000000fff00000-00000000000fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset-
FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat-
DiscTmrSERREn-
        Capabilities: <access
denied>

        Kernel driver in use:
pcieport-driver

        Kernel modules:
shpchp

00: 39 10 0a 00 07 00 10 00 00 00 04 06 04 00 01
00
10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00
20
20: 10 d4 10 d4 f1 ff 01 00 00 00 00 00 00 00 00
00
30: 00 00 00 00 b0 00 00 00 00 00 00 00 09 01 04
00

00:07.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI
bridge [1039:000a] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 16
bytes

        Bus: primary=00, secondary=4d, subordinate=4e,
sec-latency=0
        I/O behind bridge:
00003000-00004fff

        Memory behind bridge:
dc000000-dfffffff

        Prefetchable memory behind bridge:
00000000fff00000-00000000000fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset-
FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat-
DiscTmrSERREn-
        Capabilities: <access
denied>

        Kernel driver in use:
pcieport-driver

        Kernel modules:
shpchp

00: 39 10 0a 00 07 00 10 00 00 00 04 06 04 00 01
00
10: 00 00 00 00 00 00 00 00 00 4d 4e 00 31 41 00
00
20: 00 dc f0 df f1 ff 01 00 00 00 00 00 00 00 00
00
30: 00 00 00 00 b0 00 00 00 00 00 00 00 09 01 04
00

00:0f.0 Audio device [0403]: Silicon Integrated Systems [SiS] Azalia Audio
Controller [1039:7502]
        Subsystem: Fujitsu Siemens Computers Device
[1734:1125]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0 (13000ns min, 2750ns
max)
        Interrupt: pin A routed to IRQ
18
        Region 0: Memory at d4200000 (32-bit, non-prefetchable)
[size=16K]
        Capabilities: <access
denied>

        Kernel driver in use: HDA
Intel
        Kernel modules:
snd-hda-intel

00: 39 10 02 75 06 00 10 02 00 00 03 04 00 00 00
00
10: 00 00 20 d4 00 00 00 00 00 00 00 00 00 00 00
00
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25
11
30: 00 00 00 00 50 00 00 00 00 00 00 00 04 01 34
0b

00:1f.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] PCI-to-PCI
bridge [1039:0004] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 16
bytes

        Bus: primary=00, secondary=04, subordinate=04,
sec-latency=0
        I/O behind bridge:
0000f000-00000fff

        Memory behind bridge:
fff00000-000fffff

        Prefetchable memory behind bridge:
00000000fff00000-00000000000fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset-
FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat-
DiscTmrSERREn-
        Capabilities: <access
denied>

        Kernel modules:
shpchp

00: 39 10 04 00 07 00 10 00 00 00 04 06 04 00 01
00
10: 00 00 00 00 00 00 00 00 00 04 04 00 f1 01 00
20
20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00
00
30: 00 00 00 00 d0 00 00 00 00 00 00 00 ff 00 04 00

01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS]
771/671 PCIE VGA Display Adapter [1039:6351] (rev 10) (prog-if 00 [VGA
controller])
        Subsystem: Fujitsu Siemens Computers Device [1734:1125]
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin A routed to IRQ 16
        BIST result: 00
        Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
        Region 1: Memory at d4000000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at 9000 [size=128]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: <access denied>
00: 39 10 51 63 03 00 30 02 10 00 00 03 00 00 00 80
10: 08 00 00 c0 00 00 00 d4 01 90 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 34 17 25 11
30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 00 00

02:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x
802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
        Subsystem: Atheros Communications Inc. AR242x 802.11abg Wireless PCI
Express Adapter (rev 01) [168c:3067]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 16 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at d4100000 (64-bit, non-prefetchable) [size=64K]
        Capabilities: <access denied>
        Kernel driver in use: ath_pci
        Kernel modules: ath_pci, ath5k
00: 8c 16 1c 00 07 00 10 00 01 00 00 02 04 00 00 00
10: 04 00 10 d4 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 01 50 00 00 8c 16 67 30
30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 00 00

--------------------------------------------------------------

flashrom -V
flashrom
v0.9.1-r710

No coreboot table
found.

This chipset supports the following protocols:
Non-SPI.

WARNING: No chipset found. Flash detection will most likely
fail.

Calibrating delay loop... 491M loops per second, 100 myus = 199 us.
OK.

Probing for AMD Am29F010A/B, 128 KB: probe_29f040b: id1 0xff, id2
0xff

Probing for AMD Am29F002(N)BB, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for AMD Am29F002(N)BT, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for AMD Am29F016D, 2048 KB: probe_29f040b: id1 0xff, id2
0xff

Probing for AMD Am29F040B, 512 KB: probe_29f040b: id1 0x4e, id2
0x41

Probing for AMD Am29F080B, 1024 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1
is normal flash content, id2 is normal flash
content

Probing for AMD Am29LV040B, 512 KB: probe_29f040b: id1 0x4e, id2
0x41

Probing for AMD Am29LV081B, 1024 KB: probe_29f040b: id1 0x02, id2
0x00

Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Atmel AT29C512, 64 KB: probe_jedec: id1 0xee, id2 0xba, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT29C010A, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT29C020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT29C040A, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.

Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Atmel AT49BV512, 64 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xee, id2 0xba, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Atmel AT49F002(N), 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Atmel AT49F002(N)T, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for AMIC A25L40P, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for AMIC A29002B, 256 KB: probe_29f002: id1 0xff, id2
0xff

Probing for AMIC A29002T, 256 KB: probe_29f002: id1 0xff, id2
0xff

Probing for AMIC A29040B, 512 KB: probe_29f040b: id1 0x4e, id2
0x41

Probing for AMIC A49LF040A, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for EMST F49B002UA, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for EON EN29F002(A)(N)B, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for EON EN29F002(A)(N)T, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Fujitsu MBM29F004BC, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Fujitsu MBM29F004TC, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x4e, id2
0x50

Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x4e, id2
0x50

Probing for Intel 28F001BX-B, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Intel 28F001BX-T, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x4e, id2
0x41

Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x02, id2
0x00

Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.

Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.

Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.

Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI
and chip bus type SPI are
incompatible.
Probing for Macronix MX29F001B, 128 KB: probe_29f002: id1 0xff, id2
0xff

Probing for Macronix MX29F001T, 128 KB: probe_29f002: id1 0xff, id2
0xff

Probing for Macronix MX29F002B, 256 KB: probe_29f002: id1 0xff, id2
0xff

Probing for Macronix MX29F002T, 256 KB: probe_29f002: id1 0xff, id2
0xff

Probing for Macronix MX29LV040, 512 KB: probe_29f002: id1 0x4e, id2
0x41

Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Numonyx M25PE40, 256 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.

Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.

Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.

Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for PMC Pm29F0002T, 256 KB: probe_29f040b: id1 0xff, id2
0xff

Probing for PMC Pm29F0002B, 256 KB: probe_29f040b: id1 0xff, id2
0xff

Probing for PMC Pm39LV010, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for PMC Pm49FL002, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for PMC Pm49FL004, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Sharp LHF00L04, 1024 KB: probe_lhf00l04: id1 0x02, id2
0x00

Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are
incompatible.
Probing for SST SST28SF040A, 512 KB: probe_28sf040: id1 0x4e, id2
0x41

Probing for SST SST29EE010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST29LE010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST29EE020A, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SST SST29LE020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39SF010A, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39SF020A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39SF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39VF512, 64 KB: probe_jedec: id1 0xee, id2 0xba, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39VF010, 128 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39VF020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39VF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST39VF080, 1024 KB: probe_jedec: id1 0x02, id2 0x00, id1 is
normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SST SST49LF003A/B, 384 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SST SST49LF004A/B, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SST SST49LF004C, 512 KB: probe_49lfxxxc: id1 0x4e, id2
0x41

Probing for SST SST49LF008A, 1024 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1
is normal flash content, id2 is normal flash
content

Probing for SST SST49LF008C, 1024 KB: probe_49lfxxxc: id1 0x02, id2
0x00

Probing for SST SST49LF016C, 2048 KB: probe_49lfxxxc: id1 0xff, id2
0xff

Probing for SST SST49LF020, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST49LF020A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST49LF040, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content
Probing for SST SST49LF040B, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x02, id2 0x00, id1
is normal flash content, id2 is normal flash
content

Probing for SST SST49LF160C, 2048 KB: probe_49lfxxxc: id1 0xff, id2
0xff

Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.

Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.

Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.

Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.

Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus
type SPI are incompatible.
Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are
incompatible.
Probing for ST M29F002B, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for ST M29F002T/NT, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for ST M29F040B, 512 KB: probe_29f040b: id1 0x4e, id2
0x41

Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x4e, id2
0x50

Probing for ST M29W010B, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for ST M29W040B, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for ST M50FLW040A, 512 KB: probe_stm50flw0x0x: id1 0x4e, id2
0x41

Probing for ST M50FLW040B, 512 KB: probe_stm50flw0x0x: id1 0x4e, id2
0x41

Probing for ST M50FLW080A, 1024 KB: probe_stm50flw0x0x: id1 0x02, id2
0x00

Probing for ST M50FLW080B, 1024 KB: probe_stm50flw0x0x: id1 0x02, id2
0x00

Probing for ST M50FW002, 256 KB: probe_49lfxxxc: id1 0xff, id2
0xff

Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2
0xff

Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x4e, id2
0x41

Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x02, id2
0x00

Probing for ST M50LPW116, 2048 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SyncMOS S29C31004T, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SyncMOS S29C51001T, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SyncMOS S29C51002T, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for SyncMOS S29C51004T, 512 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for TI TMS29F002RB, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for TI TMS29F002RT, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash
content

Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip
bus type SPI are incompatible.
Probing for Winbond W29C011, 128 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W29C020C, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W29C040P, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011
because the probing sequence puts the AMIC A49LF040A in a funky state. Use
'flashrom -c W29EE011' if you have a board with this chip.
Probing for Winbond W39V040A, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040B, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040C, 512 KB: probe_w39v040c: id1 0x4e, id2 0x41,
id1 parity violation
Probing for Winbond W39V040FA, 512 KB: probe_jedec: id1 0x4e, id2 0x41, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080A, 1024 KB: probe_jedec: id1 0x02, id2 0x00, id1
is normal flash content, id2 is normal flash content
Probing for Winbond W49F002U, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002A, 256 KB: probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 KB: Chip lacks correct probe timing
information, using default 10mS/40uS. probe_jedec: id1 0xff, id2 0xff, id1
parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 KB: probe_winbond_fwhub: id1 0x2, id2
0x0
Probing for Winbond W39V080FA (dual mode), 512 KB: probe_winbond_fwhub: id1
0x4e, id2 0x41
Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type
Non-SPI and chip bus type SPI are incompatible.
Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI
and chip bus type SPI are incompatible.
Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type
Non-SPI and chip bus type SPI are incompatible.
Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI
and chip bus type SPI are incompatible.
Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI
and chip bus type SPI are incompatible.
Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and
chip bus type SPI are incompatible.
No EEPROM/flash device found.
If you know which flash chip you have, and if this version of flashrom
supports a similar flash chip, you can try to force read your chip. Run:
flashrom -f -r -c similar_supported_flash_chip filename

Note: flashrom can never write when the flash chip isn't found
automatically.

--------------------------

superiotool -deV

superiotool r5537
Probing for ALi Super I/O at 0x3f0...
  Failed. Returned data: id=0xffff, rev=0xff
Probing for ALi Super I/O at 0x370...
  Failed. Returned data: id=0xffff, rev=0xff
Probing for Fintek Super I/O at 0x2e...
  Failed. Returned data: vid=0xffff, id=0xffff
Probing for Fintek Super I/O at 0x4e...
  Failed. Returned data: vid=0xffff, id=0xffff
Probing for ITE Super I/O (init=standard) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x2e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=standard) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8761e) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=it8228e) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=0x87,0x87) at 0x4e...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8661f) at 0x370...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for ITE Super I/O (init=legacy/it8671f) at 0x370...
  Failed. Returned data: id=0xffff, rev=0xf
Probing for NSC Super I/O at 0x2e...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x4e...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for NSC Super I/O at 0x15c...
  Failed. Returned data: port=0xff, port+1=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370...
  Failed. Returned data: id=0xff, rev=0xff
Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370...
  Failed. Returned data: id=0xff, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x370...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x88) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x89) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x86,0x86) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for Winbond Super I/O (init=0x87,0x87) at 0x250...
  Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
Probing for VIA Super I/O at 0x3f0...
  PCI device 1106:0686 not found.
No Super I/O found
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.flashrom.org/pipermail/flashrom/attachments/20100510/f49d21c6/attachment.html>