[flashrom] [PATCH] Add coreboot IDs to make manual selection of HP xw9400 possible

[Michael Karcher]

Hi Nilse-Helge,

you experience problems trying to flash back to the HP BIOS, because with
the original Tyan BIOS, flashrom is unable to detect you have the HP OEM 
version of the board. This is why flashrom does not remove write protection
anymore. The attached patch adds a coreboot ID for the HP xw9400 board, which
makes it possible to tell flashrom you are on an xw9400 from the command line.

After applying this patch, run
   
flashrom -m hp:xw9400 -w hpbios.bin

This should return you to the original HP BIOS if the boot block write
enable jumper is shorted (the two pins next to F2), or bring you into    
big trouble if the boot block is still write protected.

Regards,
  Michael Karcher

---
 board_enable.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

diff --git a/board_enable.c b/board_enable.c
index 69de0f9..a1867be 100644
--- a/board_enable.c
+++ b/board_enable.c
@@ -1469,7 +1469,7 @@ struct board_pciid_enable board_pciid_enables[] = {
 	{0x1166, 0x0223, 0x103c, 0x320d,  0x102b, 0x0522, 0x103c, 0x31fa, NULL,          "hp",         "dl145_g3",    "HP",          "DL145 G3",              0,   OK, board_hp_dl145_g3_enable},
 	{0x8086, 0x2415, 0x103c, 0x1249,  0x10b7, 0x9200, 0x103c, 0x1246, NULL,          NULL,         NULL,          "HP",          "Vectra VL400",          0,   OK, board_hp_vl400}, 
 	{0x8086, 0x1a30, 0x103c, 0x1a30,  0x8086, 0x2443, 0x103c, 0x2440, "^VL420$",     NULL,         NULL,          "HP",          "VL420 SFF",             0,   OK, intel_ich_gpio22_raise},
-	{0x10de, 0x0369, 0x103c, 0x12fe,  0x10de, 0x0364, 0x103c, 0x12fe, NULL,          NULL,         NULL,          "HP",          "xw9400",                0,   OK, nvidia_mcp_gpio5_raise},
+	{0x10de, 0x0369, 0x103c, 0x12fe,  0x10de, 0x0364, 0x103c, 0x12fe, NULL,          "hp",         "xw9400",      "HP",          "xw9400",                0,   OK, nvidia_mcp_gpio5_raise},
 	{0x8086, 0x27A0,      0,      0,  0x8086, 0x27B9,      0,      0, NULL,          "ibase",      "mb899",       "iBASE",       "MB899",                 0,   NT, intel_ich_gpio26_raise},
 	{0x1166, 0x0205, 0x1014, 0x0347,  0x1002, 0x515E, 0x1014, 0x0325, NULL,          NULL,         NULL,          "IBM",         "x3455",                 0,   OK, board_ibm_x3455},
 	{0x1039, 0x5513, 0x8086, 0xd61f,  0x1039, 0x6330, 0x8086, 0xd61f, NULL,          NULL,         NULL,          "Intel",       "D201GLY",               0,   OK, wbsio_check_for_spi},
-- 
1.7.1