[flashrom] [PATCH] Add support for RayeR SPIPGM hardware.

Carl-Daniel Hailfinger c-d.hailfinger.devel.2006 at gmx.net
Sun Jul 18 17:36:16 CEST 2010


Updated patch for the new bitbang interface.

Add support for RayeR SPIPGM hardware as described in
http://rayer.ic.cz/elektro/spipgm.htm

To use the RayeR driver, run
flashrom -p rayer_bitbang_spi -V

Known bugs/limitations:
- Won't compile/work on non-x86 architectures.
- Will always use direct port I/O access.

Log follows:

flashrom v0.9.2-r1039 on MS-DOS 7 (i686), built with libpci 3.1.5, GCC 
4.3.2, little endian
Calibrating delay loop... OK.
Initializing rayer_bitbang_spi programmer
Using port 0x378 as I/O base for parallel port access.
...
Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 
0xc2, id2 0x2015
...
Found chip "Macronix MX25L1605" (2048 KB, SPI) at physical address 
0xffe00000.
...
No operations were specified.

Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006 at gmx.net>
Acked-by: Martin Rehak <rayer at seznam.cz>

Index: flashrom-bitbang_spi_rayer/flash.h
===================================================================
--- flashrom-bitbang_spi_rayer/flash.h	(Revision 1092)
+++ flashrom-bitbang_spi_rayer/flash.h	(Arbeitskopie)
@@ -81,6 +81,9 @@
 #if CONFIG_DEDIPROG == 1
 	PROGRAMMER_DEDIPROG,
 #endif
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	PROGRAMMER_RAYER_BITBANG_SPI,
+#endif
 	PROGRAMMER_INVALID /* This must always be the last entry. */
 };
 
@@ -129,6 +132,9 @@
 
 enum bitbang_spi_master_type {
 	BITBANG_SPI_INVALID	= 0, /* This must always be the first entry. */
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	BITBANG_SPI_MASTER_RAYER,
+#endif
 };
 
 struct bitbang_spi_master {
@@ -531,6 +537,11 @@
 int ft2232_spi_read(struct flashchip *flash, uint8_t *buf, int start, int len);
 int ft2232_spi_write_256(struct flashchip *flash, uint8_t *buf, int start, int len);
 
+/* rayer_bitbang_spi.c */
+#if CONFIG_RAYER_BITBANG_SPI == 1
+int rayer_bitbang_spi_init(void);
+#endif
+
 /* bitbang_spi.c */
 int bitbang_spi_init(const struct bitbang_spi_master *master, int halfperiod);
 int bitbang_spi_send_command(unsigned int writecnt, unsigned int readcnt, const unsigned char *writearr, unsigned char *readarr);
@@ -650,6 +661,9 @@
 #if CONFIG_DEDIPROG == 1
 	SPI_CONTROLLER_DEDIPROG,
 #endif
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	SPI_CONTROLLER_RAYER_BITBANG,
+#endif
 	SPI_CONTROLLER_INVALID /* This must always be the last entry. */
 };
 extern const int spi_programmer_count;
Index: flashrom-bitbang_spi_rayer/spi.c
===================================================================
--- flashrom-bitbang_spi_rayer/spi.c	(Revision 1092)
+++ flashrom-bitbang_spi_rayer/spi.c	(Arbeitskopie)
@@ -121,6 +121,15 @@
 	},
 #endif
 
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	{ /* SPI_CONTROLLER_RAYER_BITBANG */
+		.command = bitbang_spi_send_command,
+		.multicommand = default_spi_send_multicommand,
+		.read = bitbang_spi_read,
+		.write_256 = bitbang_spi_write_256,
+	},
+#endif
+
 	{}, /* This entry corresponds to SPI_CONTROLLER_INVALID. */
 };
 
Index: flashrom-bitbang_spi_rayer/Makefile
===================================================================
--- flashrom-bitbang_spi_rayer/Makefile	(Revision 1092)
+++ flashrom-bitbang_spi_rayer/Makefile	(Arbeitskopie)
@@ -111,8 +111,15 @@
 # Always enable serprog for now. Needs to be disabled on Windows.
 CONFIG_SERPROG ?= yes
 
-# Bitbanging SPI infrastructure is not used yet.
+# RayeR SPIPGM hardware support
+CONFIG_RAYER_BITBANG_SPI ?= yes
+
+# Bitbanging SPI infrastructure, default off unless needed.
+ifeq ($(CONFIG_RAYER_BITBANG_SPI), yes)
+override CONFIG_BITBANG_SPI = yes
+else
 CONFIG_BITBANG_SPI ?= no
+endif
 
 # Always enable 3Com NICs for now.
 CONFIG_NIC3COM ?= yes
@@ -166,6 +173,13 @@
 NEED_NET := yes
 endif
 
+ifeq ($(CONFIG_RAYER_BITBANG_SPI), yes)
+FEATURE_CFLAGS += -D'CONFIG_RAYER_BITBANG_SPI=1'
+PROGRAMMER_OBJS += rayer_bitbang_spi.o
+# Actually, NEED_PCI is wrong. NEED_IOPORT_ACCESS would be more correct.
+NEED_PCI := yes
+endif
+
 ifeq ($(CONFIG_BITBANG_SPI), yes)
 FEATURE_CFLAGS += -D'CONFIG_BITBANG_SPI=1'
 PROGRAMMER_OBJS += bitbang_spi.o
Index: flashrom-bitbang_spi_rayer/flashrom.c
===================================================================
--- flashrom-bitbang_spi_rayer/flashrom.c	(Revision 1092)
+++ flashrom-bitbang_spi_rayer/flashrom.c	(Arbeitskopie)
@@ -48,7 +48,7 @@
  * if more than one of them is selected. If only one is selected, it is clear
  * that the user wants that one to become the default.
  */
-#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_FT2232_SPI+CONFIG_SERPROG+CONFIG_BUSPIRATE_SPI+CONFIG_DEDIPROG > 1
+#if CONFIG_NIC3COM+CONFIG_NICREALTEK+CONFIG_NICNATSEMI+CONFIG_GFXNVIDIA+CONFIG_DRKAISER+CONFIG_SATASII+CONFIG_ATAHPT+CONFIG_FT2232_SPI+CONFIG_SERPROG+CONFIG_BUSPIRATE_SPI+CONFIG_DEDIPROG+CONFIG_RAYER_BITBANG_SPI > 1
 #error Please enable either CONFIG_DUMMY or CONFIG_INTERNAL or disable support for all programmers except one.
 #endif
 enum programmer programmer =
@@ -86,6 +86,9 @@
 #if CONFIG_DEDIPROG == 1
 	PROGRAMMER_DEDIPROG
 #endif
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	PROGRAMMER_RAYER_BITBANG_SPI
+#endif
 ;
 #endif
 
@@ -391,6 +394,25 @@
 	},
 #endif
 
+#if CONFIG_RAYER_BITBANG_SPI == 1
+	{
+		.name			= "rayer_bitbang_spi",
+		.init			= rayer_bitbang_spi_init,
+		.shutdown		= noop_shutdown,
+		.map_flash_region	= fallback_map,
+		.unmap_flash_region	= fallback_unmap,
+		.chip_readb		= noop_chip_readb,
+		.chip_readw		= fallback_chip_readw,
+		.chip_readl		= fallback_chip_readl,
+		.chip_readn		= fallback_chip_readn,
+		.chip_writeb		= noop_chip_writeb,
+		.chip_writew		= fallback_chip_writew,
+		.chip_writel		= fallback_chip_writel,
+		.chip_writen		= fallback_chip_writen,
+		.delay			= internal_delay,
+	},
+#endif
+
 	{}, /* This entry corresponds to PROGRAMMER_INVALID. */
 };
 
Index: flashrom-bitbang_spi_rayer/rayer_bitbang_spi.c
===================================================================
--- flashrom-bitbang_spi_rayer/rayer_bitbang_spi.c	(Revision 0)
+++ flashrom-bitbang_spi_rayer/rayer_bitbang_spi.c	(Revision 0)
@@ -0,0 +1,123 @@
+/*
+ * This file is part of the flashrom project.
+ *
+ * Copyright (C) 2009,2010 Carl-Daniel Hailfinger
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301 USA
+ */
+
+/* Driver for the SPIPGM hardware by "RayeR" Martin Rehak.
+ * See http://rayer.ic.cz/elektro/spipgm.htm for schematics and instructions.
+ */
+
+/* This driver uses non-portable direct I/O port accesses which won't work on
+ * any non-x86 platform, and even on x86 there is a high chance there will be
+ * collisions with any loaded parallel port drivers.
+ * The big advantage of direct port I/O is OS independence and speed because
+ * most OS parport drivers will perform many unnecessary accesses although
+ * this driver just treats the parallel port as a GPIO set.
+ */
+#if defined(__i386__) || defined(__x86_64__)
+
+#include "flash.h"
+
+/* We have two sets of pins, out and in. The numbers for both sets are
+ * independent and are bitshift values, not real pin numbers.
+ */
+/* Pins for master->slave direction */
+#define SPI_CS_PIN 5
+#define SPI_SCK_PIN 6
+#define SPI_MOSI_PIN 7
+/* Pins for slave->master direction */
+#define SPI_MISO_PIN 6
+
+static int lpt_iobase;
+static const struct bitbang_spi_master bitbang_spi_master_rayer;
+
+/* FIXME: All rayer_bitbang_set_* functions could use caching of the value
+ * stored at port lpt_iobase to avoid unnecessary INB. In theory, only one
+ * INB(lpt_iobase) would be needed on programmer init to get the initial
+ * value.
+ */
+
+void rayer_bitbang_set_cs(int val)
+{
+	uint8_t tmp;
+
+	tmp = INB(lpt_iobase);
+	tmp &= ~(1 << SPI_CS_PIN);
+	tmp |= (val << SPI_CS_PIN);
+	OUTB(tmp, lpt_iobase);
+}
+
+void rayer_bitbang_set_sck(int val)
+{
+	uint8_t tmp;
+
+	tmp = INB(lpt_iobase);
+	tmp &= ~(1 << SPI_SCK_PIN);
+	tmp |= (val << SPI_SCK_PIN);
+	OUTB(tmp, lpt_iobase);
+}
+
+void rayer_bitbang_set_mosi(int val)
+{
+	uint8_t tmp;
+
+	tmp = INB(lpt_iobase);
+	tmp &= ~(1 << SPI_MOSI_PIN);
+	tmp |= (val << SPI_MOSI_PIN);
+	OUTB(tmp, lpt_iobase);
+}
+
+int rayer_bitbang_get_miso(void)
+{
+	uint8_t tmp;
+
+	tmp = INB(lpt_iobase + 1);
+	tmp = (tmp >> SPI_MISO_PIN) & 0x1;
+	return tmp;
+}
+
+int rayer_bitbang_spi_init(void)
+{
+	/* Pick a default value for now. */
+	lpt_iobase = 0x378;
+
+	msg_pdbg("Using port 0x%x as I/O base for parallel port access.\n",
+		 lpt_iobase);
+
+	get_io_perms();
+
+	/* 1 usec halfperiod delay for now. */
+	if (bitbang_spi_init(&bitbang_spi_master_rayer, 1))
+		return 1;
+
+	buses_supported = CHIP_BUSTYPE_SPI;
+	spi_controller = SPI_CONTROLLER_RAYER_BITBANG;
+
+	return 0;
+}
+
+static const struct bitbang_spi_master bitbang_spi_master_rayer = {
+	.type = BITBANG_SPI_MASTER_RAYER,
+	.set_cs = rayer_bitbang_set_cs,
+	.set_sck = rayer_bitbang_set_sck,
+	.set_mosi = rayer_bitbang_set_mosi,
+	.get_miso = rayer_bitbang_get_miso,
+};
+
+#else
+#error PCI port I/O access is not supported on this architecture yet.
+#endif


-- 
http://www.hailfinger.org/





More information about the flashrom mailing list