[flashrom] [commit] r786 - trunk
svn at flashrom.org
svn at flashrom.org
Sat Nov 28 19:07:51 CET 2009
Author: libv
Date: 2009-11-28 19:07:51 +0100 (Sat, 28 Nov 2009)
New Revision: 786
Modified:
trunk/board_enable.c
Log:
Boards: provide enormous intel_ich_gpio_set function.
This code sets gpio lines on random intel ichs. Detects all currently
known intel ICHs, checks gpio lines, and then sets them accordingly.
Signed-off-by: Luc Verhaegen <libv at skynet.be>
Acked-by: Idwer Vollering <vidwer at gmail.com>
Modified: trunk/board_enable.c
===================================================================
--- trunk/board_enable.c 2009-11-27 17:49:42 UTC (rev 785)
+++ trunk/board_enable.c 2009-11-28 18:07:51 UTC (rev 786)
@@ -523,32 +523,6 @@
}
/**
- * Suited for Acorp 6A815EPD.
- */
-static int board_acorp_6a815epd(const char *name)
-{
- struct pci_dev *dev;
- uint16_t port;
- uint8_t val;
-
- dev = pci_dev_find(0x8086, 0x2440); /* Intel ICH2 LPC */
- if (!dev) {
- fprintf(stderr, "\nERROR: ICH2 LPC bridge not found.\n");
- return -1;
- }
-
- /* Use GPIOBASE register to find where the GPIO is mapped. */
- port = (pci_read_word(dev, 0x58) & 0xFFC0) + 0xE;
-
- val = INB(port);
- val |= 0x80; /* Top Block Lock -- pin 8 of PLCC32 */
- val |= 0x40; /* Lower Blocks Lock -- pin 7 of PLCC32 */
- OUTB(val, port);
-
- return 0;
-}
-
-/**
* Suited for Artec Group DBE61 and DBE62.
*/
static int board_artecgroup_dbe6x(const char *name)
@@ -590,105 +564,262 @@
}
/**
- * Set the specified GPIO on the specified ICHx southbridge to high.
- *
- * @param name The name of this board.
- * @param ich_vendor PCI vendor ID of the specified ICHx southbridge.
- * @param ich_device PCI device ID of the specified ICHx southbridge.
- * @param gpiobase_reg GPIOBASE register offset in the LPC bridge.
- * @param gp_lvl Offset of GP_LVL register in I/O space, relative to GPIOBASE.
- * @param gp_lvl_bitmask GP_LVL bitmask (set GPIO bits to 1, all others to 0).
- * @param gpio_bit The bit (GPIO) which shall be set to high.
- * @return If the write-enable was successful return 0, otherwise return -1.
+ * Set a GPIO line on a given intel ICH LPC controller.
*/
-static int ich_gpio_raise(const char *name, uint16_t ich_vendor,
- uint16_t ich_device, uint8_t gpiobase_reg,
- uint8_t gp_lvl, uint32_t gp_lvl_bitmask,
- unsigned int gpio_bit)
+static int intel_ich_gpio_set(int gpio, int raise)
{
+ /* table mapping the different intel ICH LPC chipsets. */
+ static struct {
+ uint16_t id;
+ uint8_t base_reg;
+ uint32_t bank0;
+ uint32_t bank1;
+ uint32_t bank2;
+ } intel_ich_gpio_table[] = {
+ {0x2410, 0x58, 0x0FE30000, 0, 0}, /* 82801AA (ICH) */
+ {0x2420, 0x58, 0x0FE30000, 0, 0}, /* 82801AB (ICH0) */
+ {0x2440, 0x58, 0x1BFF391B, 0, 0}, /* 82801BA (ICH2) */
+ {0x244C, 0x58, 0x1A23399B, 0, 0}, /* 82801BAM (ICH2M) */
+ {0x2450, 0x58, 0x1BFF0000, 0, 0}, /* 82801E (C-ICH) */
+ {0x2480, 0x58, 0x1BFF0000, 0x00000FFF, 0}, /* 82801CA (ICH3-S) */
+ {0x248C, 0x58, 0x1A230000, 0x00000FFF, 0}, /* 82801CAM (ICH3-M) */
+ {0x24C0, 0x58, 0x1BFF0000, 0x00000FFF, 0}, /* 82801DB/DBL (ICH4/ICH4-L) */
+ {0x24CC, 0x58, 0x1A030000, 0x00000FFF, 0}, /* 82801DBM (ICH4-M) */
+ {0x24D0, 0x58, 0x1BFF0000, 0x00030305, 0}, /* 82801EB/ER (ICH5/ICH5R) */
+ {0x2640, 0x48, 0x1BFF0000, 0x00030307, 0}, /* 82801FB/FR (ICH6/ICH6R) */
+ {0x2641, 0x48, 0x1BFF0000, 0x00030307, 0}, /* 82801FBM (ICH6M) */
+ {0x27B8, 0x48, 0xFFFFFFFF, 0x000300FF, 0}, /* 82801GB/GR (ICH7 Family) */
+ {0x27B9, 0x48, 0xFFEBFFFE, 0x000300FE, 0}, /* 82801GBM (ICH7-M) */
+ {0x27BD, 0x48, 0xFFEBFFFE, 0x000300FE, 0}, /* 82801GHM (ICH7-M DH) */
+ {0x2810, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HB/HR (ICH8/R) */
+ {0x2811, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HBM (ICH8M-E) */
+ {0x2812, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HH (ICH8DH) */
+ {0x2814, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HO (ICH8DO) */
+ {0x2815, 0x48, 0xFFFFFFFF, 0x00FF0FFF, 0}, /* 82801HEM (ICH8M) */
+ {0x2912, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IH (ICH9DH) */
+ {0x2914, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IO (ICH9DO) */
+ {0x2916, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IR (ICH9R) */
+ {0x2917, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IEM (ICH9M-E) */
+ {0x2918, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IB (ICH9) */
+ {0x2919, 0x48, 0xFFFFFFFF, 0x00FFFFFF, 0}, /* 82801IBM (ICH9M) */
+ {0x3A14, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JDO (ICH10DO) */
+ {0x3A16, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIR (ICH10R) */
+ {0x3A18, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JIB (ICH10) */
+ {0x3A1A, 0x48, 0xFFFFFFFF, 0xFFFFFFFF, 0x00000100}, /* 82801JD (ICH10D) */
+ {0, 0, 0, 0, 0} /* end marker */
+ };
+
struct pci_dev *dev;
- uint16_t gpiobar;
- uint32_t reg32;
+ uint16_t base;
+ uint32_t tmp;
+ int i, allowed;
- dev = pci_dev_find(ich_vendor, ich_device); /* Intel ICHx LPC */
+ /* First, look for a known LPC bridge */
+ for (dev = pacc->devices; dev; dev = dev->next)
+ if ((dev->vendor_id == 0x8086) &&
+ (dev->device_class == 0x0601)) { /* ISA Bridge */
+ /* Is this device in our list? */
+ for (i = 0; intel_ich_gpio_table[i].id; i++)
+ if (dev->device_id == intel_ich_gpio_table[i].id)
+ break;
+
+ if (intel_ich_gpio_table[i].id)
+ break;
+ }
+
if (!dev) {
- fprintf(stderr, "\nERROR: ICHx LPC dev %4x:%4x not found.\n",
- ich_vendor, ich_device);
+ fprintf(stderr, "\nERROR: No Known Intel LPC Bridge found.\n");
return -1;
}
- /* Use GPIOBASE register to find the I/O space for GPIO. */
- gpiobar = pci_read_word(dev, gpiobase_reg) & gp_lvl_bitmask;
+ /* According to the datasheets, all intel ICHs have the gpio bar 5:1
+ strapped to zero. From some mobile ich9 version on, this becomes
+ 6:1. The mask below catches all. */
+ base = pci_read_word(dev, intel_ich_gpio_table[i].base_reg) & 0xFFC0;
- /* Set specified GPIO to high. */
- reg32 = INL(gpiobar + gp_lvl);
- reg32 |= (1 << gpio_bit);
- OUTL(reg32, gpiobar + gp_lvl);
+ /* check whether the line is allowed */
+ if (gpio < 32)
+ allowed = (intel_ich_gpio_table[i].bank0 >> gpio) & 0x01;
+ else if (gpio < 64)
+ allowed = (intel_ich_gpio_table[i].bank1 >> (gpio - 32)) & 0x01;
+ else
+ allowed = (intel_ich_gpio_table[i].bank2 >> (gpio - 64)) & 0x01;
+ if (!allowed) {
+ fprintf(stderr, "\nERROR: This Intel LPC Bridge does not allow"
+ " setting GPIO%02d\n", gpio);
+ return -1;
+ }
+
+ printf("\nIntel ICH LPC Bridge: %sing GPIO%02d.\n",
+ raise ? "Rais" : "Dropp", gpio);
+
+ if (gpio < 32) {
+ /* Set line to GPIO */
+ tmp = INL(base);
+ /* ICH/ICH0 multiplexes 27/28 on the line set. */
+ if ((gpio == 28) &&
+ ((dev->device_id == 0x2410) || (dev->device_id == 0x2420)))
+ tmp |= 1 << 27;
+ else
+ tmp |= 1 << gpio;
+ OUTL(tmp, base);
+
+ /* As soon as we are talking to ICH8 and above, this register
+ decides whether we can set the gpio or not. */
+ if (dev->device_id > 0x2800) {
+ tmp = INL(base);
+ if (!(tmp & (1 << gpio))) {
+ fprintf(stderr, "\nERROR: This Intel LPC Bridge"
+ " does not allow setting GPIO%02d\n",
+ gpio);
+ return -1;
+ }
+ }
+
+ /* Set GPIO to OUTPUT */
+ tmp = INL(base + 0x04);
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x04);
+
+ /* Raise GPIO line */
+ tmp = INL(base + 0x0C);
+ if (raise)
+ tmp |= 1 << gpio;
+ else
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x0C);
+ } else if (gpio < 64) {
+ gpio -= 32;
+
+ /* Set line to GPIO */
+ tmp = INL(base + 0x30);
+ tmp |= 1 << gpio;
+ OUTL(tmp, base + 0x30);
+
+ /* As soon as we are talking to ICH8 and above, this register
+ decides whether we can set the gpio or not. */
+ if (dev->device_id > 0x2800) {
+ tmp = INL(base + 30);
+ if (!(tmp & (1 << gpio))) {
+ fprintf(stderr, "\nERROR: This Intel LPC Bridge"
+ " does not allow setting GPIO%02d\n",
+ gpio + 32);
+ return -1;
+ }
+ }
+
+ /* Set GPIO to OUTPUT */
+ tmp = INL(base + 0x34);
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x34);
+
+ /* Raise GPIO line */
+ tmp = INL(base + 0x38);
+ if (raise)
+ tmp |= 1 << gpio;
+ else
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x38);
+ } else {
+ gpio -= 64;
+
+ /* Set line to GPIO */
+ tmp = INL(base + 0x40);
+ tmp |= 1 << gpio;
+ OUTL(tmp, base + 0x40);
+
+ tmp = INL(base + 40);
+ if (!(tmp & (1 << gpio))) {
+ fprintf(stderr, "\nERROR: This Intel LPC Bridge does "
+ "not allow setting GPIO%02d\n", gpio + 64);
+ return -1;
+ }
+
+ /* Set GPIO to OUTPUT */
+ tmp = INL(base + 0x44);
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x44);
+
+ /* Raise GPIO line */
+ tmp = INL(base + 0x48);
+ if (raise)
+ tmp |= 1 << gpio;
+ else
+ tmp &= ~(1 << gpio);
+ OUTL(tmp, base + 0x48);
+ }
+
return 0;
}
/**
- * Suited for ASUS P4B266.
+ * Suited for Abit IP35: Intel P35 + ICH9R.
*/
-static int ich2_gpio22_raise(const char *name)
+static int intel_ich_gpio16_raise(const char *name)
{
- return ich_gpio_raise(name, 0x8086, 0x2440, 0x58, 0x0c, 0xffc0, 22);
+ return intel_ich_gpio_set(16, 1);
}
/**
- * Suited for the Dell PowerEdge 1850. All parameters except the last one are
- * documented in the public Intel 82801EB ICH5 / 82801ER ICH5R datasheet. The
- * last parameter (GPIO number) has to be in the range [16,31] according to
- * said Intel datasheet and was found by exhaustive search.
+ * Suited for MSI MS-7046: LGA775 + 915P + ICH6.
*/
-static int ich5_gpio23_raise(const char *name)
+static int intel_ich_gpio19_raise(const char *name)
{
- return ich_gpio_raise(name, 0x8086, 0x24d0, 0x58, 0x0c, 0xffc0, 23);
+ return intel_ich_gpio_set(19, 1);
}
/**
- * Suited for MSI MS-7046.
+ * Suited for Asus P4P800-E Deluxe: Intel socket478 + 865PE + ICH5R.
*/
-static int ich6_gpio19_raise(const char *name)
+static int intel_ich_gpio21_raise(const char *name)
{
- return ich_gpio_raise(name, 0x8086, 0x2640, 0x48, 0x0c, 0xffc0, 19);
+ return intel_ich_gpio_set(21, 1);
}
-static int board_kontron_986lcd_m(const char *name)
+/**
+ * Suited for ASUS P4B266: socket478 + intel 845D + ICH2.
+ */
+static int intel_ich_gpio22_raise(const char *name)
{
- struct pci_dev *dev;
- uint16_t gpiobar;
- uint32_t val;
+ return intel_ich_gpio_set(22, 1);
+}
-#define ICH7_GPIO_LVL2 0x38
+/**
+ * Suited for Dell Poweredge 1850: Intel PPGA604 + E7520 + ICH5R.
+ */
+static int intel_ich_gpio23_raise(const char *name)
+{
+ return intel_ich_gpio_set(23, 1);
+}
- dev = pci_dev_find(0x8086, 0x27b8); /* Intel ICH7 LPC */
- if (!dev) {
- // This will never happen on this board
- fprintf(stderr, "\nERROR: ICH7 LPC bridge not found.\n");
- return -1;
- }
+/**
+ * Suited for Acorp 6A815EPD: socket 370 + intel 815 + ICH2.
+ */
+static int board_acorp_6a815epd(const char *name)
+{
+ int ret;
- /* Use GPIOBASE register to find where the GPIO is mapped. */
- gpiobar = pci_read_word(dev, 0x48) & 0xfffc;
+ /* Lower Blocks Lock -- pin 7 of PLCC32 */
+ ret = intel_ich_gpio_set(22, 1);
+ if (!ret) /* Top Block Lock -- pin 8 of PLCC32 */
+ ret = intel_ich_gpio_set(23, 1);
- val = INL(gpiobar + ICH7_GPIO_LVL2); /* GP_LVL2 */
- printf_debug("\nGPIOBAR=0x%04x GP_LVL: 0x%08x\n", gpiobar, val);
+ return ret;
+}
- /* bit 2 (0x04) = 0 #TBL --> bootblock locking = 1
- * bit 2 (0x04) = 1 #TBL --> bootblock locking = 0
- * bit 3 (0x08) = 0 #WP --> block locking = 1
- * bit 3 (0x08) = 1 #WP --> block locking = 0
- *
- * To enable full block locking, you would do:
- * val &= ~ ((1 << 2) | (1 << 3));
- */
- val |= (1 << 2) | (1 << 3);
+/**
+ * Suited for Kontron 986LCD-M: socket478 + 915GM + ICH7R.
+ */
+static int board_kontron_986lcd_m(const char *name)
+{
+ int ret;
- OUTL(val, gpiobar + ICH7_GPIO_LVL2);
+ ret = intel_ich_gpio_set(34, 1); /* #TBL */
+ if (!ret)
+ ret = intel_ich_gpio_set(35, 1); /* #WP */
- return 0;
+ return ret;
}
/**
@@ -881,32 +1012,6 @@
}
/**
- * Suited for Abit IP35: Intel P35 + ICH9R.
- */
-static int board_abit_ip35(const char *name)
-{
- struct pci_dev *dev;
- uint16_t base;
- uint8_t tmp;
-
- dev = pci_dev_find(0x8086, 0x2916); /* Intel ICH9R LPC Interface */
- if (!dev) {
- fprintf(stderr, "\nERROR: Intel ICH9R LPC not found.\n");
- return -1;
- }
-
- /* get LPC GPIO base */
- base = pci_read_long(dev, 0x48) & 0x0000FFC0;
-
- /* Raise GPIO 16 */
- tmp = INB(base + 0x0E);
- tmp |= 0x01;
- OUTB(tmp, base + 0x0E);
-
- return 0;
-}
-
-/**
* Suited for Asus A7V8X: VIA KT400 + VT8235 + IT8703F-A
*/
static int board_asus_a7v8x(const char *name)
@@ -1009,32 +1114,6 @@
}
/**
- * Suited for Asus P4P800-E Deluxe: Intel Intel 865PE + ICH5R.
- */
-static int board_asus_p4p800(const char *name)
-{
- struct pci_dev *dev;
- uint16_t base;
- uint8_t tmp;
-
- dev = pci_dev_find(0x8086, 0x24D0); /* Intel ICH5R ISA Bridge */
- if (!dev) {
- fprintf(stderr, "\nERROR: Intel ICH5R ISA Bridge not found.\n");
- return -1;
- }
-
- /* get PM IO base */
- base = pci_read_long(dev, 0x58) & 0x0000FFC0;
-
- /* Raise GPIO 21 */
- tmp = INB(base + 0x0E);
- tmp |= 0x20;
- OUTB(tmp, base + 0x0E);
-
- return 0;
-}
-
-/**
* Below is the list of boards which need a special "board enable" code in
* flashrom before their ROM chip can be accessed/written to.
*
@@ -1063,7 +1142,7 @@
/* Please keep this list alphabetically ordered by vendor/board name. */
struct board_pciid_enable board_pciid_enables[] = {
/* first pci-id set [4], second pci-id set [4], coreboot id [2], vendor name board name flash enable */
- {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, "Abit", "IP35", board_abit_ip35},
+ {0x8086, 0x2926, 0x147b, 0x1084, 0x11ab, 0x4364, 0x147b, 0x1084, NULL, NULL, "Abit", "IP35", intel_ich_gpio16_raise},
{0x8086, 0x1130, 0, 0, 0x105a, 0x0d30, 0x105a, 0x4d33, "acorp", "6a815epd", "Acorp", "6A815EPD", board_acorp_6a815epd},
{0x1022, 0x746B, 0x1022, 0x36C0, 0, 0, 0, 0, "AGAMI", "ARUMA", "agami", "Aruma", w83627hf_gpio24_raise_2e},
{0x1106, 0x3177, 0x17F2, 0x3177, 0x1106, 0x3148, 0x17F2, 0x3148, NULL, NULL, "Albatron", "PM266A*", board_epox_ep_8k5a2},
@@ -1073,12 +1152,12 @@
{0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3065, 0x1043, 0x80ED, NULL, NULL, "ASUS", "A7V600-X", board_asus_a7v600x},
{0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x808C, NULL, NULL, "ASUS", "A7V8X", board_asus_a7v8x},
{0x1106, 0x3177, 0x1043, 0x80A1, 0x1106, 0x3205, 0x1043, 0x8118, NULL, NULL, "ASUS", "A7V8X-MX SE", board_asus_a7v8x_mx},
- {0x8086, 0x1a30, 0x1043, 0x8070, 0x8086, 0x244b, 0x1043, 0x8028, NULL, NULL, "ASUS", "P4B266", ich2_gpio22_raise},
- {0x8086, 0x2570, 0x1043, 0x80F2, 0x105A, 0x3373, 0x1043, 0x80F5, NULL, NULL, "ASUS", "P4P800-E Deluxe", board_asus_p4p800},
+ {0x8086, 0x1a30, 0x1043, 0x8070, 0x8086, 0x244b, 0x1043, 0x8028, NULL, NULL, "ASUS", "P4B266", intel_ich_gpio22_raise},
+ {0x8086, 0x2570, 0x1043, 0x80F2, 0x105A, 0x3373, 0x1043, 0x80F5, NULL, NULL, "ASUS", "P4P800-E Deluxe", intel_ich_gpio21_raise},
{0x10B9, 0x1541, 0, 0, 0x10B9, 0x1533, 0, 0, "asus", "p5a", "ASUS", "P5A", board_asus_p5a},
{0x10DE, 0x0030, 0x1043, 0x818a, 0x8086, 0x100E, 0x1043, 0x80EE, NULL, NULL, "ASUS", "P5ND2-SLI Deluxe", board_asus_p5nd2_sli},
{0x1106, 0x3149, 0x1565, 0x3206, 0x1106, 0x3344, 0x1565, 0x1202, NULL, NULL, "Biostar", "P4M80-M4", it8705_rom_write_enable},
- {0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, "Dell", "PowerEdge 1850", ich5_gpio23_raise},
+ {0x8086, 0x3590, 0x1028, 0x016c, 0x1000, 0x0030, 0x1028, 0x016c, NULL, NULL, "Dell", "PowerEdge 1850", intel_ich_gpio23_raise},
{0x1106, 0x3038, 0x1019, 0x0996, 0x1106, 0x3177, 0x1019, 0x0996, NULL, NULL, "Elitegroup", "K7VTA3", it8705f_write_enable_2e},
{0x1106, 0x3177, 0x1106, 0x3177, 0x1106, 0x3059, 0x1695, 0x3005, NULL, NULL, "EPoX", "EP-8K5A2", board_epox_ep_8k5a2},
{0x10EC, 0x8139, 0x1695, 0x9001, 0x11C1, 0x5811, 0x1695, 0x9015, NULL, NULL, "EPoX", "EP-8RDA3+", board_epox_ep_8rda3plus},
@@ -1103,7 +1182,7 @@
{0x13f6, 0x0111, 0x1462, 0x5900, 0x1106, 0x3177, 0x1106, 0, "msi", "kt4ultra", "MSI", "MS-6590 (KT4 Ultra)",board_msi_kt4v},
{0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, NULL, NULL, "MSI", "MS-6702E (K8T Neo2-F)",w83627thf_gpio4_4_raise_2e},
{0x1106, 0x0571, 0x1462, 0x7120, 0, 0, 0, 0, "msi", "kt4v", "MSI", "MS-6712 (KT4V)", board_msi_kt4v},
- {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, "MSI", "MS-7046", ich6_gpio19_raise},
+ {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, "MSI", "MS-7046", intel_ich_gpio19_raise},
{0x10de, 0x005e, 0, 0, 0, 0, 0, 0, "msi", "k8n-neo3", "MSI", "MS-7135 (K8N Neo3)", w83627thf_gpio4_4_raise_4e},
{0x1106, 0x3104, 0x1297, 0xa238, 0x1106, 0x3059, 0x1297, 0xc063, NULL, NULL, "Shuttle", "AK38N", it8705f_write_enable_2e},
{0x10DE, 0x0050, 0x1297, 0x5036, 0x1412, 0x1724, 0x1297, 0x5036, NULL, NULL, "Shuttle", "FN25", board_shuttle_fn25},
More information about the flashrom
mailing list