[flashrom] Abit IP35 needs board enable.

[Luc Verhaegen]

On Mon, Jul 06, 2009 at 08:18:32PM +0100, Richie Ward wrote:
> Oh and I hope i used right program :) Is this ok?
> 
> > Found Winbond W83627DHG (id=0xa0, rev=0x23) at 0x2e
> > Register dump:
> > idx 02 20 21 22 23 24 25 26  27 28 29 2a 2b 2c 2d 2e  2f
> > val ff a0 23 ff 00 4c 00 00  ff 50 00 7c c0 0a 01 00  ff
> > def 00 a0 NA ff 00 MM 00 MM  RR 50 00 00 RR e2 21 00  00
> > LDN 0x00 (Floppy)
> > idx 30 60 61 70 74 f0 f1 f2  f4 f5
> > val 00 00 00 00 04 0e 00 ff  00 00
> > def 01 03 f0 06 02 8e 00 ff  00 00
> > LDN 0x01 (Parallel port)
> > idx 30 60 61 70 74 f0
> > val 00 00 00 00 04 38
> > def 01 03 78 07 04 3f
> > LDN 0x02 (COM1)
> > idx 30 60 61 70 f0
> > val 00 00 00 00 00
> > def 01 03 f8 04 00
> > LDN 0x03 (COM2)
> > idx 30 60 61 70 f0 f1
> > val 00 00 00 00 00 00
> > def 01 02 f8 03 00 00
> > LDN 0x05 (Keyboard)
> > idx 30 60 61 62 63 70 72 f0
> > val 01 00 60 00 64 01 0c 80
> > def 01 00 60 00 64 01 0c 83
> > LDN 0x06 (Serial peripheral interface)
> > idx 30 62 63
> > val 00 ff ff
> > def 00 00 00
> > LDN 0x07 (GPIO 6)
> > idx 30 f4 f5 f6 f7
> > val 07 ff ff ff ff
> > def 00 ff 00 00 00
> > LDN 0x08 (WDTO#, PLED)
> > idx 30 f5 f6 f7
> > val 00 ff 00 ff
> > def 00 00 00 00
> > LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5)
> > idx 30 e0 e1 e2 e3 e4 e5 e6  e7 e8 e9 f0 f1 f2 f3 f4  f5 f6 f7 fe
> > val 0e ff 01 00 ff ff ff ff  e3 ff 01 ff e3 00 00 c0  ff 20 00 00
> > def 00 ff 00 00 ff 00 00 00  00 00 00 ff 00 00 00 ff  00 00 00 00
> > LDN 0x0a (ACPI)
> > idx 30 70 e0 e1 e2 e3 e4 e5  e6 e7 e8 e9 f2 f3 f4 f6  f7 fe
> > val 00 00 00 00 f0 04 00 00  1c 10 09 00 7d 00 00 00  08 00
> > def 00 00 01 00 ff 08 00 RR  1c 00 RR RR 7c 00 00 00  00 00
> > LDN 0x0b (Hardware monitor)
> > idx 30 60 61 70 f0 f1 f2
> > val 01 02 90 02 81 ff 81
> > def 00 00 00 00 81 00 00
> > LDN 0x0c (PECI, SST)
> > idx e0 e1 e2 e3 e4 e5 e8 f1  fe ff
> > val 10 52 48 48 48 00 01 48  00 00
> > def 00 48 48 48 48 00 00 48  00 00

Yeah, looking through this now.

Luc Verhaegen.