[coreboot] [v2] r4456 - in trunk/coreboot-v2/src/southbridge/intel/i82801gx: . acpi
svn at coreboot.org
svn at coreboot.org
Tue Jul 21 23:50:34 CEST 2009
Author: stepan
Date: 2009-07-21 23:50:34 +0200 (Tue, 21 Jul 2009)
New Revision: 4456
Added:
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/globalnvs.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_ac97.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/sleepstates.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_power.h
Modified:
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_audio.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smihandler.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_debug.c
trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c
Log:
Intel ICH7 updates
- code restructuring (move ich7 out of i945)
- ACPI fixes
- major SMI handler updates
- make sure SMBus lives where we expect it
- try to get usb debug working
Signed-off-by: Stefan Reinauer <stepan at coresystems.de>
Acked-by: Peter Stuge <peter at stuge.se>
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/globalnvs.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/globalnvs.asl (rev 0)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/globalnvs.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -0,0 +1,161 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Global Variables */
+
+Name(\PICM, 0) // IOAPIC/8259
+Name(\DSEN, 1) // Display Output Switching Enable
+
+/* Global ACPI memory region. This region is used for passing information
+ * between coreboot (aka "the system bios"), ACPI, and the SMI handler.
+ * Since we don't know where this will end up in memory at ACPI compile time,
+ * we have to fix it up in coreboot's ACPI creation phase.
+ */
+
+
+OperationRegion (GNVS, SystemMemory, 0xC0DEBABE, 0x100)
+Field (GNVS, ByteAcc, NoLock, Preserve)
+{
+ /* Miscellaneous */
+ Offset (0x00),
+ OSYS, 16, // 0x00 - Operating System
+ SMIF, 8, // 0x02 - SMI function
+ PRM0, 8, // 0x03 - SMI function parameter
+ PRM1, 8, // 0x04 - SMI function parameter
+ SCIF, 8, // 0x05 - SCI function
+ PRM2, 8, // 0x06 - SCI function parameter
+ PRM3, 8, // 0x07 - SCI function parameter
+ LCKF, 8, // 0x08 - Global Lock function for EC
+ PRM4, 8, // 0x09 - Lock function parameter
+ PRM5, 8, // 0x0a - Lock function parameter
+ P80D, 32, // 0x0b - Debug port (IO 0x80) value
+ LIDS, 8, // 0x0f - LID state (open = 1)
+ PWRS, 8, // 0x10 - Power State (AC = 1)
+ DBGS, 8, // 0x11 - Debug State
+ LINX, 8, // 0x12 - Linux OS
+ DCKN, 8, // 0x13 - PCIe docking state
+ /* Thermal policy */
+ Offset (0x14),
+ ACTT, 8, // 0x14 - active trip point
+ PSVT, 8, // 0x15 - passive trip point
+ TC1V, 8, // 0x16 - passive trip point TC1
+ TC2V, 8, // 0x17 - passive trip point TC2
+ TSPV, 8, // 0x18 - passive trip point TSP
+ CRTT, 8, // 0x19 - critical trip point
+ DTSE, 8, // 0x1a - Digital Thermal Sensor enable
+ DTS1, 8, // 0x1b - DT sensor 1
+ DTS2, 8, // 0x1c - DT sensor 2
+ /* Battery Support */
+ Offset (0x1e),
+ BNUM, 8, // 0x1e - number of batteries
+ B0SC, 8, // 0x1f - BAT0 stored capacity
+ B1SC, 8, // 0x20 - BAT1 stored capacity
+ B2SC, 8, // 0x21 - BAT2 stored capacity
+ B0SS, 8, // 0x22 - BAT0 stored status
+ B1SS, 8, // 0x23 - BAT1 stored status
+ B2SS, 8, // 0x24 - BAT2 stored status
+ /* Processor Identification */
+ Offset (0x28),
+ APIC, 8, // 0x28 - APIC Enabled by coreboot
+ MPEN, 8, // 0x29 - Multi Processor Enable
+ PCP0, 8, // 0x2a - PDC CPU/CORE 0
+ PCP1, 8, // 0x2b - PDC CPU/CORE 1
+ PPCM, 8, // 0x2c - Max. PPC state
+ /* Super I/O & CMOS config */
+ Offset (0x32),
+ NATP, 8, // 0x32 - ...
+ /* Integrated Graphics Device */
+ Offset (0x3c),
+ IGDS, 8, // 0x3c - IGD state (primary = 1)
+ TLST, 8, // 0x3d - Display Toggle List pointer
+ CADL, 8, // 0x3e - Currently Attached Devices List
+ PADL, 8, // 0x3f - Previously Attached Devices List
+ CSTE, 16, // 0x40 - Current display state
+ NSTE, 16, // 0x42 - Next display state
+ SSTE, 16, // 0x44 - Set display state
+ Offset (0x46),
+ NDID, 8, // 0x46 - Number of Device IDs
+ DID1, 32, // 0x47 - Device ID 1
+ DID2, 32, // 0x4b - Device ID 2
+ DID3, 32, // 0x4f - Device ID 3
+ DID4, 32, // 0x53 - Device ID 4
+ DID5, 32, // 0x57 - Device ID 5
+ /* Backlight Control */
+ Offset (0x64),
+ BLCS, 8, // 0x64 - Backlight control possible?
+ BRTL, 8, // 0x65 - Brightness Level
+ ODDS, 8, // 0x66
+ /* Ambient Light Sensors */
+ Offset (0x6e),
+ ALSE, 8, // 0x6e - ALS enable
+ ALAF, 8, // 0x6f - Ambient light adjustment factor
+ LLOW, 8, // 0x70 - LUX Low
+ LHIH, 8, // 0x71 - LUX High
+ /* EMA */
+ Offset (0x78),
+ EMAE, 8, // 0x78 - EMA enable
+ EMAP, 16, // 0x79 - EMA pointer
+ EMAL, 16, // 0x7b - EMA length
+ /* MEF */
+ Offset (0x82),
+ MEFE, 8, // 0x82 - MEF enable
+ /* TPM support */
+ Offset (0x8c),
+ TPMP, 8, // 0x8c - TPM
+ TPME, 8, // 0x8d - TPM enable
+ /* SATA */
+ Offset (0x96),
+ GTF0, 56, // 0x96 - GTF task file buffer for port 0
+ GTF1, 56, // 0x9d - GTF task file buffer for port 1
+ GTF2, 56, // 0xa4 - GTF task file buffer for port 2
+ IDEM, 8, // 0xab - IDE mode (compatible / enhanced)
+ IDET, 8, // 0xac - IDE
+ /* IGD OpRegion */
+ Offset (0xb4),
+ ASLB, 32, // 0xb4 - IGD OpRegion Base Address
+ IBTT, 8, // 0xb8 - IGD boot panel device
+ IPAT, 8, // 0xb9 - IGD panel type cmos option
+ ITVF, 8, // 0xba - IGD TV format cmos option
+ ITVM, 8, // 0xbb - IGD TV minor format option
+ IPSC, 8, // 0xbc - IGD panel scaling
+ IBLC, 8, // 0xbd - IGD BLC config
+ IBIA, 8, // 0xbe - IGD BIA config
+ ISSC, 8, // 0xbf - IGD SSC config
+ I409, 8, // 0xc0 - IGD 0409 modified settings
+ I509, 8, // 0xc1 - IGD 0509 modified settings
+ I609, 8, // 0xc2 - IGD 0609 modified settings
+ I709, 8, // 0xc3 - IGD 0709 modified settings
+ IDMM, 8, // 0xc4 - IGD DVMT Mode
+ IDMS, 8, // 0xc5 - IGD DVMT memory size
+ IF1E, 8, // 0xc6 - IGD function 1 enable
+ HVCO, 8, // 0xc7 - IGD HPLL VCO
+ NXD1, 32, // 0xc8 - IGD _DGS next DID1
+ NXD2, 32, // 0xcc - IGD _DGS next DID2
+ NXD3, 32, // 0xd0 - IGD _DGS next DID3
+ NXD4, 32, // 0xd4 - IGD _DGS next DID4
+ NXD5, 32, // 0xd8 - IGD _DGS next DID5
+ NXD6, 32, // 0xdc - IGD _DGS next DID6
+ NXD7, 32, // 0xe0 - IGD _DGS next DID7
+ NXD8, 32, // 0xe4 - IGD _DGS next DID8
+ /* Mainboard Specific (TODO move elsewhere) */
+ Offset (0xf0),
+ DOCK, 8, // 0xf0 - Docking Status
+}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7.asl 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -92,7 +92,8 @@
Offset(0x38), // GPIO Level 2
, 5,
GP37, 1, // PATA_PWR_EN
- , 2,
+ GP38, 1, // Battery / Power (?)
+ GP39, 1, // ??
GL05, 8,
GL06, 8,
GL07, 8
@@ -100,7 +101,7 @@
// ICH7 Root Complex Register Block. Memory Mapped through RCBA)
- OperationRegion(RCRB, SystemMemory, 0xfff1000, 0x4000)
+ OperationRegion(RCRB, SystemMemory, 0xfed1c000, 0x4000)
Field(RCRB, DWordAcc, Lock, Preserve)
{
Offset(0x0000), // Backbone
@@ -111,12 +112,22 @@
, 5,
HPTE, 1, // Address Enable
Offset(0x3418), // FD (Function Disable)
- , 1,
+ , 1, // Reserved
PATD, 1, // PATA disable
SATD, 1, // SATA disable
SMBD, 1, // SMBUS disable
HDAD, 1, // Azalia disable
- , 11, // ... FIXME
+ A97D, 1, // AC'97 disable
+ M97D, 1, // AC'97 disable
+ ILND, 1, // Internal LAN disable
+ US1D, 1, // UHCI #1 disable
+ US2D, 1, // UHCI #2 disable
+ US3D, 1, // UHCI #3 disable
+ US4D, 1, // UHCI #4 disable
+ , 2, // Reserved
+ LPBD, 1, // LPC bridge disable
+ EHCD, 1, // EHCI disable
+ Offset(0x341a), // FD Root Ports
RP1D, 1, // Root Port 1 disable
RP2D, 1, // Root Port 2 disable
RP3D, 1, // Root Port 3 disable
@@ -139,6 +150,9 @@
// PCI Bridge
Include ("../../../southbridge/intel/i82801gx/acpi/ich7_pci.asl")
+// AC97 Audio and Modem
+Include ("../../../southbridge/intel/i82801gx/acpi/ich7_ac97.asl")
+
// LPC Bridge
Include ("../../../southbridge/intel/i82801gx/acpi/ich7_lpc.asl")
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_ac97.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_ac97.asl (rev 0)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_ac97.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -0,0 +1,40 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+/* Intel i82801G AC'97 Audio and Modem */
+
+// Intel AC'97 Audio 0:1e.2
+
+Device (AUD0)
+{
+ Name (_ADR, 0x001e0002)
+}
+
+// Intel AC'97 Modem 0:1e.3
+
+Device (MODM)
+{
+ Name (_ADR, 0x001e0003)
+
+ Name (_PRW, Package(){ 5, 4 })
+}
+
+
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_audio.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_audio.asl 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_audio.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -27,6 +27,10 @@
{
Name (_ADR, 0x001b0000)
- Name (_PRW, Package(){ 13, 4 })
+ // Power Resources for Wake
+ Name (_PRW, Package(){
+ 5, // Bit 5 of GPE
+ 4 // Can wake from S4 state.
+ })
}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_lpc.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -68,7 +68,7 @@
})
}
- Device (FWHD) // Firmware Hub
+ Device (FWH) // Firmware Hub
{
Name (_HID, EISAID("INT0800"))
Name (_CRS, ResourceTemplate()
@@ -80,7 +80,7 @@
Device (HPET)
{
Name (_HID, EISAID("PNP0103"))
- Name (_CID, EISAID("PNP0C01"))
+ Name (_CID, 0x010CD041)
Name(BUF0, ResourceTemplate()
{
@@ -92,19 +92,33 @@
If (HPTE) {
// Note: Ancient versions of Windows don't want
// to see the HPET in order to work right
- // Return (0xb) // Enable and don't show device
-
- Return (0xf) // Enable and show device
+ If (LGreaterEqual(OSYS, 2001)) {
+ Return (0xf) // Enable and show device
+ } Else {
+ Return (0xb) // Enable and don't show device
+ }
}
Return (0x0) // Not enabled, don't show.
}
- Method (_CRS, 0, Serialized)
+ Method (_CRS, 0, Serialized) // Current resources
{
- // Here we could do crazy stuff like move the HPET. Why
- // should we?
+ If (HPTE) {
+ CreateDWordField(BUF0, \_SB.PCI0.LPCB.HPET.FED0._BAS, HPT0)
+ If (Lequal(HPAS, 1)) {
+ Store(0xfed01000, HPT0)
+ }
+ If (Lequal(HPAS, 2)) {
+ Store(0xfed02000, HPT0)
+ }
+
+ If (Lequal(HPAS, 3)) {
+ Store(0xfed03000, HPT0)
+ }
+ }
+
Return (BUF0)
}
}
@@ -130,7 +144,7 @@
IO (Decode16, 0xb4, 0xb4, 0x01, 0x02)
IO (Decode16, 0xb8, 0xb8, 0x01, 0x02)
IO (Decode16, 0xbc, 0xbc, 0x01, 0x02)
- IO (Decode16, 0x4d0, 0x4b0, 0x01, 0x02)
+ IO (Decode16, 0x4d0, 0x4d0, 0x01, 0x02)
IRQNoFlags () { 2 }
})
}
@@ -145,7 +159,7 @@
})
}
- Device(MISC) // Various other devices
+ Device(LDRC) // LPC device: Resource consumption
{
Name (_HID, EISAID("PNP0C02"))
Name (_UID, 2)
@@ -153,18 +167,18 @@
{
IO (Decode16, 0x2e, 0x2e, 0x1, 0x02) // First SuperIO
IO (Decode16, 0x4e, 0x4e, 0x1, 0x02) // Second SuperIO
- IO (Decode16, 0x61, 0x61, 0x1, 0x1) // NMI Status
- IO (Decode16, 0x63, 0x63, 0x1, 0x1) // CPU Reserved
- IO (Decode16, 0x65, 0x65, 0x1, 0x1) // CPU Reserved
- IO (Decode16, 0x67, 0x67, 0x1, 0x1) // CPU Reserved
- IO (Decode16, 0x80, 0x80, 0x1, 0x1) // Port 80 Post
- IO (Decode16, 0x92, 0x92, 0x1, 0x1) // CPU Reserved
+ IO (Decode16, 0x61, 0x61, 0x1, 0x01) // NMI Status
+ IO (Decode16, 0x63, 0x63, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x65, 0x65, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x67, 0x67, 0x1, 0x01) // CPU Reserved
+ IO (Decode16, 0x80, 0x80, 0x1, 0x01) // Port 80 Post
+ IO (Decode16, 0x92, 0x92, 0x1, 0x01) // CPU Reserved
IO (Decode16, 0xb2, 0xb2, 0x1, 0x02) // SWSMI
- IO (Decode16, 0x680, 0x680, 0x1, 0x70) // IO ???
+ // IO (Decode16, 0x680, 0x680, 0x1, 0x70) // IO ???
IO (Decode16, 0x800, 0x800, 0x1, 0x10) // ACPI I/O trap
IO (Decode16, 0x0500, 0x0500, 0x1, 0x80) // ICH7-M ACPI
- IO (Decode16, 0x1180, 0x1180, 0x1, 0x40) // ICH7-M GPIO
- IO (Decode16, 0x1640, 0x1640, 0x1, 0x10) // IO ???
+ IO (Decode16, 0x0480, 0x0480, 0x1, 0x40) // ICH7-M GPIO
+ // IO (Decode16, 0x1640, 0x1640, 0x1, 0x10) // IO ???
})
}
@@ -194,12 +208,19 @@
Device (PS2K) // Keyboard
{
Name(_HID, EISAID("PNP0303"))
+ Name(_CID, EISAID("PNP030B"))
+
Name(_CRS, ResourceTemplate()
{
IO (Decode16, 0x60, 0x60, 0x01, 0x01)
IO (Decode16, 0x64, 0x64, 0x01, 0x01)
IRQ (Edge, ActiveHigh, Exclusive) { 0x01 } // IRQ 1
})
+
+ Method (_STA, 0)
+ {
+ Return (0xf)
+ }
}
Device (PS2M) // Mouse
@@ -209,5 +230,36 @@
{
IRQ (Edge, ActiveHigh, Exclusive) { 0x0c } // IRQ 12
})
+
+ Method(_STA, 0)
+ {
+ Return (0xf)
+ }
}
+
+ Device (FDC0) // Floppy controller
+ {
+ Name (_HID, EisaId ("PNP0700"))
+ Method (_STA, 0, NotSerialized)
+ {
+ Return (0x0f) // FIXME
+ }
+
+ Name(_CRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x03F0, 0x03F0, 0x01, 0x06)
+ IO (Decode16, 0x03F7, 0x03F7, 0x01, 0x01)
+ IRQNoFlags () {6}
+ DMA (Compatibility, NotBusMaster, Transfer8) {2}
+ })
+
+ Name(_PRS, ResourceTemplate()
+ {
+ IO (Decode16, 0x03F0, 0x03F0, 0x01, 0x06)
+ IO (Decode16, 0x03F7, 0x03F7, 0x01, 0x01)
+ IRQNoFlags () {6}
+ DMA (Compatibility, NotBusMaster, Transfer8) {2}
+ })
+
+ }
}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_pci.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -43,6 +43,24 @@
Name (_PRW, Package(){ 11, 4 })
}
+ Device (SLT6)
+ {
+ Name (_ADR, 0x00050000)
+ Name (_PRW, Package(){ 11, 4 })
+ }
+
+ Device (LANC)
+ {
+ Name (_ADR, 0x00080000)
+ Name (_PRW, Package(){ 11, 3 })
+ }
+
+ Device (LANR)
+ {
+ Name (_ADR, 0x00000000)
+ Name (_PRW, Package(){ 11, 3 })
+ }
+
// TODO: How many slots, where?
// PCI Interrupt Routing.
@@ -52,47 +70,7 @@
Method (_PRT)
{
- If (PICM) {
- Return (Package() {
- // PCI Slot 1 routes FGHE
- Package() { 0x0000ffff, 0, 0, 16}, /* Firewire */
- Package() { 0x0000ffff, 1, 0, 22},
- Package() { 0x0000ffff, 2, 0, 23},
- Package() { 0x0000ffff, 3, 0, 20},
-
- // PCI Slot 2 routes GFEH (but is EFGH now, because that actually works)
- Package() { 0x0001ffff, 0, 0, 20},
- Package() { 0x0001ffff, 1, 0, 21},
- Package() { 0x0001ffff, 2, 0, 22},
- Package() { 0x0001ffff, 3, 0, 23},
-
- // PCI Slot 3 routes CDBA
- Package() { 0x0002ffff, 0, 0, 18},
- Package() { 0x0002ffff, 1, 0, 19},
- Package() { 0x0002ffff, 2, 0, 17},
- Package() { 0x0002ffff, 3, 0, 16}
- })
- } Else {
- Return (Package() {
- // PCI Slot 1 routes FGHE
- Package() { 0x0000ffff, 0, \_SB.PCI0.LPCB.LNKF, 0},
- Package() { 0x0000ffff, 1, \_SB.PCI0.LPCB.LNKE, 0},
- Package() { 0x0000ffff, 2, \_SB.PCI0.LPCB.LNKH, 0},
- Package() { 0x0000ffff, 3, \_SB.PCI0.LPCB.LNKG, 0},
-
- // PCI Slot 2 routes GFEH
- Package() { 0x0001ffff, 0, \_SB.PCI0.LPCB.LNKG, 0},
- Package() { 0x0001ffff, 1, \_SB.PCI0.LPCB.LNKF, 0},
- Package() { 0x0001ffff, 2, \_SB.PCI0.LPCB.LNKE, 0},
- Package() { 0x0001ffff, 3, \_SB.PCI0.LPCB.LNKH, 0},
-
- // PCI Slot 3 routes CDBA
- Package() { 0x0002ffff, 0, \_SB.PCI0.LPCB.LNKC, 0},
- Package() { 0x0002ffff, 1, \_SB.PCI0.LPCB.LNKD, 0},
- Package() { 0x0002ffff, 2, \_SB.PCI0.LPCB.LNKB, 0},
- Package() { 0x0002ffff, 3, \_SB.PCI0.LPCB.LNKA, 0},
- })
- }
+ Include ("acpi/ich7_pci_irqs.asl")
}
}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/ich7_smbus.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -33,7 +33,8 @@
I2CE, 1
}
- OperationRegion (SMBI, SystemIO, 0x500, 0x20)
+ /*
+ OperationRegion (SMBI, SystemIO, 0x400, 0x20)
Field (SMBI, ByteAcc, NoLock, Preserve)
{
HSTS, 8, // Host Status
@@ -236,6 +237,7 @@
Return (0xffff)
}
+ */
// Todo: Does anyone ever use these?
// Missing: Read / Write Word
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/sleepstates.asl
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/sleepstates.asl (rev 0)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/acpi/sleepstates.asl 2009-07-21 21:50:34 UTC (rev 4456)
@@ -0,0 +1,27 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2007-2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+Name(\_S0, Package(4){0x0,0x0,0,0})
+Name(\_S1, Package(4){0x1,0x0,0,0})
+Name(\_S3, Package(4){0x5,0x0,0,0})
+Name(\_S4, Package(4){0x6,0x0,0,0})
+Name(\_S5, Package(4){0x7,0x0,0,0})
+
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx.h 2009-07-21 21:50:34 UTC (rev 4456)
@@ -21,9 +21,16 @@
#ifndef SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H
#define SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H
+/* __ROMCC__ is set by auto.c to make sure
+ * none of the stage2 data structures are included.
+ */
+#ifndef __ROMCC__
#include "chip.h"
extern void i82801gx_enable(device_t dev);
+#endif
+/* PCI Configuration Space (D31:F0): LPC */
+
#define SERIRQ_CNTL 0x64
#define GEN_PMCON_1 0xa0
@@ -58,7 +65,31 @@
#define IDE_TIM_PRI 0x40 /* IDE timings, primary */
#define IDE_DECODE_ENABLE (1 << 15)
#define IDE_SITRE (1 << 14)
+#define IDE_ISP_5_CLOCKS (0 << 12)
+#define IDE_ISP_4_CLOCKS (1 << 12)
+#define IDE_ISP_3_CLOCKS (2 << 12)
+#define IDE_RCT_4_CLOCKS (0 << 8)
+#define IDE_RCT_3_CLOCKS (1 << 8)
+#define IDE_RCT_2_CLOCKS (2 << 8)
+#define IDE_RCT_1_CLOCKS (3 << 8)
+#define IDE_DTE1 (1 << 7)
+#define IDE_PPE1 (1 << 6)
+#define IDE_IE1 (1 << 5)
+#define IDE_TIME1 (1 << 4)
+#define IDE_DTE0 (1 << 3)
+#define IDE_PPE0 (1 << 2)
+#define IDE_IE0 (1 << 1)
+#define IDE_TIME0 (1 << 0)
#define IDE_TIM_SEC 0x42 /* IDE timings, secondary */
+
+#define IDE_SDMA_CNT 0x48 /* Synchronous DMA control */
+#define IDE_SSDE1 (1 << 3)
+#define IDE_SSDE0 (1 << 2)
+#define IDE_PSDE1 (1 << 1)
+#define IDE_PSDE0 (1 << 0)
+
+#define IDE_SDMA_TIM 0x4a
+
#define IDE_CONFIG 0x54 /* IDE I/O Configuration Register */
#define SIG_MODE_NORMAL (0 << 16)
#define SIG_MODE_TRISTATE (1 << 16)
@@ -78,12 +109,13 @@
#define HST_EN (1 << 0)
/* SMBus I/O bits.
- * TODO: It does not matter where we put the SMBus IO base, as long as we keep
- * consistent and don't interfere with other devices. Stage2 will relocate
- * this anyways. But it's a general problem we have not solved in the brightest
- * possible way.
+ * It does not matter where we put the SMBus I/O base, as long as we
+ * keep it consistent and don't interfere with other devices. Stage2
+ * will relocate this anyways.
+ * Our solution is to have SMB initialization move the I/O to SMBUS_IO_BASE
+ * again. But handling static BARs is a generic problem that should be
+ * solved in the device allocator.
*/
-/* #define SMBUS_IO_BASE 0x1000 */
#define SMBUS_IO_BASE 0x0400
#define SMBHSTSTAT 0x0
@@ -103,4 +135,124 @@
/* HPET, if present */
#define HPET_ADDR 0xfed0000
+/* Southbridge IO BARs */
+
+/* TODO Make sure these don't get changed by stage2 */
+#define GPIOBASE 0x48
+#define DEFAULT_GPIOBASE 0x480
+
+#define PMBASE 0x40
+#define DEFAULT_PMBASE 0x500
+
+/* Root Complex Register Block */
+#define RCBA 0xf0
+#define DEFAULT_RCBA 0xfed1c000
+
+#define RCBA8(x) *((volatile u8 *)(DEFAULT_RCBA + x))
+#define RCBA16(x) *((volatile u16 *)(DEFAULT_RCBA + x))
+#define RCBA32(x) *((volatile u32 *)(DEFAULT_RCBA + x))
+
+#define VCH 0x0000 /* 32bit */
+#define VCAP1 0x0004 /* 32bit */
+#define VCAP2 0x0008 /* 32bit */
+#define PVC 0x000c /* 16bit */
+#define PVS 0x000e /* 16bit */
+
+#define V0CAP 0x0010 /* 32bit */
+#define V0CTL 0x0014 /* 32bit */
+#define V0STS 0x001a /* 16bit */
+
+#define V1CAP 0x001c /* 32bit */
+#define V1CTL 0x0020 /* 32bit */
+#define V1STS 0x0026 /* 16bit */
+
+#define RCTCL 0x0100 /* 32bit */
+#define ESD 0x0104 /* 32bit */
+#define ULD 0x0110 /* 32bit */
+#define ULBA 0x0118 /* 64bit */
+
+#define RP1D 0x0120 /* 32bit */
+#define RP1BA 0x0128 /* 64bit */
+#define RP2D 0x0130 /* 32bit */
+#define RP2BA 0x0138 /* 64bit */
+#define RP3D 0x0140 /* 32bit */
+#define RP3BA 0x0148 /* 64bit */
+#define RP4D 0x0150 /* 32bit */
+#define RP4BA 0x0158 /* 64bit */
+#define HDD 0x0160 /* 32bit */
+#define HDBA 0x0168 /* 64bit */
+#define RP5D 0x0170 /* 32bit */
+#define RP5BA 0x0178 /* 64bit */
+#define RP6D 0x0180 /* 32bit */
+#define RP6BA 0x0188 /* 64bit */
+
+#define ILCL 0x01a0 /* 32bit */
+#define LCAP 0x01a4 /* 32bit */
+#define LCTL 0x01a8 /* 16bit */
+#define LSTS 0x01aa /* 16bit */
+
+#define RPC 0x0224 /* 32bit */
+#define RPFN 0x0238 /* 32bit */
+
+#define TRSR 0x1e00 /* 8bit */
+#define TRCR 0x1e10 /* 64bit */
+#define TWDR 0x1e18 /* 64bit */
+
+#define IOTR0 0x1e80 /* 64bit */
+#define IOTR1 0x1e88 /* 64bit */
+#define IOTR2 0x1e90 /* 64bit */
+#define IOTR3 0x1e98 /* 64bit */
+
+#define TCTL 0x3000 /* 8bit */
+
+#define D31IP 0x3100 /* 32bit */
+#define D30IP 0x3104 /* 32bit */
+#define D29IP 0x3108 /* 32bit */
+#define D28IP 0x310c /* 32bit */
+#define D27IP 0x3110 /* 32bit */
+#define D31IR 0x3140 /* 16bit */
+#define D30IR 0x3142 /* 16bit */
+#define D29IR 0x3144 /* 16bit */
+#define D28IR 0x3146 /* 16bit */
+#define D27IR 0x3148 /* 16bit */
+#define OIC 0x31ff /* 8bit */
+
+#define RC 0x3400 /* 32bit */
+#define HPTC 0x3404 /* 32bit */
+#define GCS 0x3410 /* 32bit */
+#define BUC 0x3414 /* 32bit */
+#define FD 0x3418 /* 32bit */
+#define CG 0x341c /* 32bit */
+
+/* Function Disable (FD) register values.
+ * Setting a bit disables the corresponding
+ * feature.
+ * Not all features might be disabled on
+ * all chipsets. Esp. ICH-7U is picky.
+ */
+#define FD_PCIE6 (1 << 21)
+#define FD_PCIE5 (1 << 20)
+#define FD_PCIE4 (1 << 19)
+#define FD_PCIE3 (1 << 18)
+#define FD_PCIE2 (1 << 17)
+#define FD_PCIE1 (1 << 16)
+#define FD_EHCI (1 << 15)
+#define FD_LPCB (1 << 14)
+
+/* UHCI must be disabled from 4 downwards.
+ * If UHCI controllers get disabled, EHCI
+ * must know about it, too! */
+#define FD_UHCI4 (1 << 11)
+#define FD_UHCI34 (1 << 10) | FD_UHCI4
+#define FD_UHCI234 (1 << 9) | FD_UHCI3
+#define FD_UHCI1234 (1 << 8) | FD_UHCI2
+
+#define FD_INTLAN (1 << 7)
+#define FD_ACMOD (1 << 6)
+#define FD_ACAUD (1 << 5)
+#define FD_HDAUD (1 << 4)
+#define FD_SMBUS (1 << 3)
+#define FD_SATA (1 << 2)
+#define FD_PATA (1 << 1)
+
#endif /* SOUTHBRIDGE_INTEL_I82801GX_I82801GX_H */
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_ac97.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -251,6 +251,21 @@
}
}
+static void ac97_set_subsystem(device_t dev, unsigned vendor, unsigned device)
+{
+ if (!vendor || !device) {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ pci_read_config32(dev, PCI_VENDOR_ID));
+ } else {
+ pci_write_config32(dev, PCI_SUBSYSTEM_VENDOR_ID,
+ ((device & 0xffff) << 16) | (vendor & 0xffff));
+ }
+}
+
+static struct pci_operations ac97_pci_ops = {
+ .set_subsystem = ac97_set_subsystem,
+};
+
static struct device_operations ac97_audio_ops = {
.read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
@@ -258,6 +273,7 @@
.init = ac97_audio_init,
.scan_bus = 0,
.enable = i82801gx_enable,
+ .ops_pci = &ac97_pci_ops,
};
static struct device_operations ac97_modem_ops = {
@@ -267,6 +283,7 @@
.init = ac97_modem_init,
.scan_bus = 0,
.enable = i82801gx_enable,
+ .ops_pci = &ac97_pci_ops,
};
/* 82801GB/GR/GDH/GBM/GHM (ICH7/ICH7R/ICH7DH/ICH7-M/ICH7-M DH) */
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_lpc.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -27,18 +27,13 @@
#include <pc80/i8259.h>
#include <arch/io.h>
#include "i82801gx.h"
+#include "i82801gx_power.h"
-#include "../../../northbridge/intel/i945/ich7.h"
+#define NMI_OFF 0
-#define MAINBOARD_POWER_OFF 0
-#define MAINBOARD_POWER_ON 1
+#define ENABLE_ACPI_MODE_IN_COREBOOT 0
+#define TEST_SMM_FLASH_LOCKDOWN 0
-#ifndef CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL
-#define CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL MAINBOARD_POWER_ON
-#endif
-
-#define NMI_OFF 0
-
typedef struct southbridge_intel_i82801gx_config config_t;
/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control
@@ -78,7 +73,9 @@
volatile u32 *ioapic_index = (volatile u32 *)0xfec00000;
volatile u32 *ioapic_data = (volatile u32 *)0xfec00010;
- /* Enable ACPI I/O and power management. */
+ /* Enable ACPI I/O and power management.
+ * Set SCI IRQ to IRQ9
+ */
pci_write_config8(dev, ACPI_CNTL, 0x80);
*ioapic_index = 0;
@@ -109,6 +106,27 @@
(1 << 7) | (1 << 6) | ((21 - 17) << 2) | (0 << 0));
}
+/* PIRQ[n]_ROUT[3:0] - PIRQ Routing Control
+ * 0x00 - 0000 = Reserved
+ * 0x01 - 0001 = Reserved
+ * 0x02 - 0010 = Reserved
+ * 0x03 - 0011 = IRQ3
+ * 0x04 - 0100 = IRQ4
+ * 0x05 - 0101 = IRQ5
+ * 0x06 - 0110 = IRQ6
+ * 0x07 - 0111 = IRQ7
+ * 0x08 - 1000 = Reserved
+ * 0x09 - 1001 = IRQ9
+ * 0x0A - 1010 = IRQ10
+ * 0x0B - 1011 = IRQ11
+ * 0x0C - 1100 = IRQ12
+ * 0x0D - 1101 = Reserved
+ * 0x0E - 1110 = IRQ14
+ * 0x0F - 1111 = IRQ15
+ * PIRQ[n]_ROUT[7] - PIRQ Routing Control
+ * 0x80 - The PIRQ is not routed.
+ */
+
static void i82801gx_pirq_init(device_t dev)
{
device_t irq_dev;
@@ -180,10 +198,14 @@
pci_write_config32(dev, 0xb8, reg32);
}
+extern u8 acpi_slp_type;
+
static void i82801gx_power_options(device_t dev)
{
u8 reg8;
- u16 reg16;
+ u16 reg16, pmbase;
+ u32 reg32;
+ char *state;
int pwr_on=CONFIG_MAINBOARD_POWER_ON_AFTER_POWER_FAIL;
int nmi_option;
@@ -195,16 +217,28 @@
get_option(&pwr_on, "power_on_after_fail");
reg8 = pci_read_config8(dev, GEN_PMCON_3);
reg8 &= 0xfe;
- if (pwr_on) {
+ switch (pwr_on) {
+ case MAINBOARD_POWER_OFF:
+ reg8 |= 1;
+ state = "off";
+ break;
+ case MAINBOARD_POWER_ON:
reg8 &= ~1;
- } else {
- reg8 |= 1;
+ state = "on";
+ break;
+ case MAINBOARD_POWER_KEEP:
+ reg8 &= ~1;
+ state = "state keep";
+ break;
+ default:
+ state = "undefined";
}
+
reg8 |= (3 << 4); /* avoid #S4 assertions */
reg8 &= ~(1 << 3); /* minimum asssertion is 1 to 2 RTCCLK */
pci_write_config8(dev, GEN_PMCON_3, reg8);
- printk_info("Set power %s after power failure.\n", pwr_on ? "on" : "off");
+ printk_info("Set power %s after power failure.\n", state);
/* Set up NMI on errors. */
reg8 = inb(0x61);
@@ -226,15 +260,27 @@
}
outb(reg8, 0x70);
- // Enable CPU_SLP# and Intel Speedstep, set SMI# rate down
+ /* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */
reg16 = pci_read_config16(dev, GEN_PMCON_1);
reg16 &= ~((3 << 0) | (1 << 10));
reg16 |= (1 << 3) | (1 << 5);
- reg16 |= (1 << 2); // CLKRUN_EN
+ reg16 |= (1 << 2); // CLKRUN_EN
pci_write_config16(dev, GEN_PMCON_1, reg16);
// Set the board's GPI routing.
i82801gx_gpi_routing(dev);
+
+ /* Set up power management block and determine sleep mode */
+ pmbase = pci_read_config16(dev, 0x40) & 0xfffe;
+ reg32 = inl(pmbase + 0x04); // PM1_CNT
+#if HAVE_ACPI_RESUME
+ acpi_slp_type = (((reg32 >> 10) & 7) == 5) ? 3 : 0;
+ printk_debug("PM1_CNT: 0x%08x --> acpi_sleep_type: %x\n",
+ reg32, acpi_slp_type);
+#endif
+ reg32 |= (1 << 1); // enable C3->C0 transition on bus master
+ reg32 |= 1; // SCI_EN
+ outl(reg32, pmbase + 0x04);
}
static void i82801gx_configure_cstates(device_t dev)
@@ -273,9 +319,10 @@
{
u32 reg32;
- /* Leave HPET at default address, but enable it */
+ /* Move HPET to default address 0xfed00000 and enable it */
reg32 = RCBA32(0x3404);
reg32 |= (1 << 7); // HPET Address Enable
+ reg32 &= ~(3 << 0);
RCBA32(0x3404) = reg32;
}
@@ -467,6 +514,13 @@
.ops_pci = &pci_ops,
};
+/* 82801GH (ICH7 DH) */
+static const struct pci_driver ich7_dh_lpc __pci_driver = {
+ .ops = &device_ops,
+ .vendor = PCI_VENDOR_ID_INTEL,
+ .device = 0x27b0,
+};
+
/* 82801GB/GR (ICH7/ICH7R) */
static const struct pci_driver ich7_ich7r_lpc __pci_driver = {
.ops = &device_ops,
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_nvs.h 2009-07-21 21:50:34 UTC (rev 4456)
@@ -1,7 +1,7 @@
/*
* This file is part of the coreboot project.
*
- * Copyright (C) 2008 coresystems GmbH
+ * Copyright (C) 2008-2009 coresystems GmbH
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
@@ -20,44 +20,48 @@
*/
typedef struct {
- u16 osys;
- u8 smif;
- u8 prm0;
- u8 prm1;
- u8 scif;
- u8 prm2;
- u8 prm3;
- u8 lckf;
- u8 prm4;
- u8 prm5;
- u32 p80d;
- u8 lids;
- u8 pwrs;
- u8 dbgs;
- u8 linxs;
- u8 rsvd;
- u8 actt;
- u8 psvt;
- u8 tc1v;
- u8 tc2v;
- u8 tspv;
- u8 crtt;
- u8 dtse;
- u8 dts1;
- u8 dts2;
+ /* Miscellaneous */
+ u16 osys; /* 0x00 - Operating System */
+ u8 smif; /* 0x02 - SMI function call ("TRAP") */
+ u8 prm0; /* 0x03 - SMI function call parameter */
+ u8 prm1; /* 0x04 - SMI function call parameter */
+ u8 scif; /* 0x05 - SCI function call (via _L00) */
+ u8 prm2; /* 0x06 - SCI function call parameter */
+ u8 prm3; /* 0x07 - SCI function call parameter */
+ u8 lckf; /* 0x08 - Global Lock function for EC */
+ u8 prm4; /* 0x09 - Lock function parameter */
+ u8 prm5; /* 0x0a - Lock function parameter */
+ u32 p80d; /* 0x0b - Debug port (IO 0x80) value */
+ u8 lids; /* 0x0f - LID state (open = 1) */
+ u8 pwrs; /* 0x10 - Power state (AC = 1) */
+ u8 dbgs; /* 0x11 - Debug state */
+ u8 linx; /* 0x12 - Linux OS */
+ u8 dckn; /* 0x13 - PCIe docking state */
+ /* Thermal policy */
+ u8 actt; /* 0x14 - active trip point */
+ u8 psvt; /* 0x15 - passive trip point */
+ u8 tc1v; /* 0x16 - passive trip point TC1 */
+ u8 tc2v; /* 0x17 - passive trip point TC2 */
+ u8 tspv; /* 0x18 - passive trip point TSP */
+ u8 crtt; /* 0x19 - critical trip point */
+ u8 dtse; /* 0x1a - Digital Thermal Sensor enable */
+ u8 dts1; /* 0x1b - DT sensor 1 */
+ u8 dts2; /* 0x1c - DT sensor 2 */
u8 rsvd2;
- u8 bnum;
- u8 b0sc, b1sc, b2sc;
- u8 b0ss, b1ss, b2ss;
+ /* Battery Support */
+ u8 bnum; /* 0x1e - number of batteries */
+ u8 b0sc, b1sc, b2sc; /* 0x1f-0x21 - stored capacity */
+ u8 b0ss, b1ss, b2ss; /* 0x22-0x24 - stored status */
u8 rsvd3[3];
- u8 apic;
- u8 mpen;
- u8 bten;
- u8 ppcm;
- u8 pcp0;
- u8 pcp1;
- u8 rsvd4[4];
- u8 natp;
+ /* Processor Identification */
+ u8 apic; /* 0x28 - APIC enabled */
+ u8 mpen; /* 0x29 - MP capable/enabled */
+ u8 pcp0; /* 0x2a - PDC CPU/CORE 0 */
+ u8 pcp1; /* 0x2b - PDC CPU/CORE 1 */
+ u8 ppcm; /* 0x2c - Max. PPC state */
+ u8 rsvd4[5];
+ /* Super I/O & CMOS config */
+ u8 natp; /* 0x32 - SIO type */
u8 cmap;
u8 cmbp;
u8 lptp;
@@ -67,42 +71,69 @@
u8 rtcf;
u8 util;
u8 acin;
- u8 igds;
- u8 tlst;
- u8 cadl;
- u8 padl;
- u16 cste;
- u16 pste;
- u16 nste;
- u16 sste;
- u8 ndid;
- u32 did1;
- u32 did2;
- u32 did3;
- u32 did4;
- u32 did5;
- u8 rsvd5[0xb];
+ /* Integrated Graphics Device */
+ u8 igds; /* 0x3c - IGD state */
+ u8 tlst; /* 0x3d - Display Toggle List Pointer */
+ u8 cadl; /* 0x3e - currently attached devices */
+ u8 padl; /* 0x3f - previously attached devices */
+ u16 cste; /* 0x40 - current display state */
+ u16 nste; /* 0x42 - next display state */
+ u16 sste; /* 0x44 - set display state */
+ u8 ndid; /* 0x46 - number of device ids */
+ u32 did[5]; /* 0x47 - 5b device id 1..5 */
+ u8 rsvd5[0x9];
+ /* Backlight Control */
+ u8 blcs; /* 0x64 - Backlight Control possible */
u8 brtl;
u8 odds;
- u8 alse;
+ u8 rsvd6[0x7];
+ /* Ambient Light Sensors*/
+ u8 alse; /* 0x6e - ALS enable */
u8 alaf;
u8 llow;
u8 lhih;
- u8 rsvd6;
- u8 emae;
+ u8 rsvd7[0x6];
+ /* EMA */
+ u8 emae; /* 0x78 - EMA enable */
u16 emap;
u16 emal;
- u8 rsvd7;
- u8 mefe;
- u8 igps;
- u8 rsvd8[2];
- u8 tpmp;
+ u8 rsvd8[0x5];
+ /* MEF */
+ u8 mefe; /* 0x82 - MEF enable */
+ u8 rsvd9[0x9];
+ /* TPM support */
+ u8 tpmp; /* 0x8c - TPM */
u8 tpme;
- u8 rsvd9[8];
- u8 gtf0[7];
+ u8 rsvd10[8];
+ /* SATA */
+ u8 gtf0[7]; /* 0x96 - GTF task file buffer for port 0 */
+ u8 gtf1[7];
u8 gtf2[7];
u8 idem;
u8 idet;
- u8 dock;
-} global_nvs_t;
+ u8 rsvd11[7];
+ /* IGD OpRegion (not implemented yet) */
+ u32 aslb; /* 0xb4 - IGD OpRegion Base Address */
+ u8 ibtt;
+ u8 ipat;
+ u8 itvf;
+ u8 itvm;
+ u8 ipsc;
+ u8 iblc;
+ u8 ibia;
+ u8 issc;
+ u8 i409;
+ u8 i509;
+ u8 i609;
+ u8 i709;
+ u8 idmm;
+ u8 idms;
+ u8 if1e;
+ u8 hvco;
+ u32 nxd[8];
+ u8 rsvd12[8];
+ /* Mainboard specific */
+ u8 dock; /* 0xf0 - Docking Status */
+ u8 rsvd13[15];
+} __attribute__((packed)) global_nvs_t;
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_pci.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -81,7 +81,7 @@
command = pci_read_config16(dev, PCI_COMMAND);
command |= dev->command;
-#if PCI_BRIDGE_UPDATE_COMMAND
+#ifdef PCI_BRIDGE_UPDATE_COMMAND
/* If we write to PCI_COMMAND, on some systems
* this will cause the ROM and APICs not being visible
* anymore.
Added: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_power.h
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_power.h (rev 0)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_power.h 2009-07-21 21:50:34 UTC (rev 4456)
@@ -0,0 +1,29 @@
+/*
+ * This file is part of the coreboot project.
+ *
+ * Copyright (C) 2009 coresystems GmbH
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; version 2 of
+ * the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#define MAINBOARD_POWER_OFF 0
+#define MAINBOARD_POWER_ON 1
+#define MAINBOARD_POWER_KEEP 2
+
+#ifndef MAINBOARD_POWER_ON_AFTER_FAIL
+#define MAINBOARD_POWER_ON_AFTER_FAIL MAINBOARD_POWER_ON
+#endif
+
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_sata.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -35,8 +35,10 @@
printk_debug("i82801gx_sata: initializing...\n");
- if (config == NULL)
+ if (config == NULL) {
printk_err("i82801gx_sata: error: device not in Config.lb!\n");
+ return;
+ }
/* SATA configuration */
@@ -55,12 +57,15 @@
pci_write_config8(dev, 0x09, 0x80);
/* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, 0x8000);
- pci_write_config16(dev, IDE_TIM_SEC, 0xa307);
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
/* Sync DMA */
- pci_write_config16(dev, 0x48, 0x0004);
- pci_write_config16(dev, 0x4a, 0x0200);
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0200);
/* Set IDE I/O Configuration */
reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
@@ -84,12 +89,15 @@
pci_write_config8(dev, INTR_LN, 0x0a);
/* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, 0xa307);
- pci_write_config16(dev, IDE_TIM_SEC, 0x8000);
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_ISP_5_CLOCKS | IDE_RCT_4_CLOCKS);
/* Sync DMA */
- pci_write_config16(dev, 0x48, 0x0001);
- pci_write_config16(dev, 0x4a, 0x0001);
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0001);
/* Set IDE I/O Configuration */
reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
@@ -126,12 +134,16 @@
pci_write_config8(dev, INTR_LN, 0xff);
/* Set timings */
- pci_write_config16(dev, IDE_TIM_PRI, 0xa307);
- pci_write_config16(dev, IDE_TIM_SEC, 0xe303);
+ pci_write_config16(dev, IDE_TIM_PRI, IDE_DECODE_ENABLE |
+ IDE_ISP_3_CLOCKS | IDE_RCT_1_CLOCKS |
+ IDE_PPE0 | IDE_IE0 | IDE_TIME0);
+ pci_write_config16(dev, IDE_TIM_SEC, IDE_DECODE_ENABLE |
+ IDE_SITRE | IDE_ISP_3_CLOCKS |
+ IDE_RCT_1_CLOCKS | IDE_IE0 | IDE_TIME0);
/* Sync DMA */
- pci_write_config16(dev, 0x48, 0x0005);
- pci_write_config16(dev, 0x4a, 0x0201);
+ pci_write_config16(dev, IDE_SDMA_CNT, IDE_SSDE0 | IDE_PSDE0);
+ pci_write_config16(dev, IDE_SDMA_TIM, 0x0201);
/* Set IDE I/O Configuration */
reg32 = SIG_MODE_NORMAL | FAST_PCB1 | FAST_PCB0 | PCB1 | PCB0;
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smbus.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -29,6 +29,19 @@
#include "i82801gx.h"
#include "i82801gx_smbus.h"
+#define SMB_BASE 0x20
+static void smbus_init(struct device *dev)
+{
+ u32 smb_base;
+
+ smb_base = pci_read_config32(dev, SMB_BASE);
+ printk_debug("Initializing SMBus device:\n");
+ printk_debug(" Old SMBUS Base Address: 0x%04x\n", smb_base);
+ pci_write_config32(dev, SMB_BASE, 0x00000401);
+ smb_base = pci_read_config32(dev, SMB_BASE);
+ printk_debug(" New SMBUS Base Address: 0x%04x\n", smb_base);
+}
+
static int lsmbus_read_byte(device_t dev, u8 address)
{
u16 device;
@@ -65,7 +78,7 @@
.read_resources = pci_dev_read_resources,
.set_resources = pci_dev_set_resources,
.enable_resources = pci_dev_enable_resources,
- .init = 0,
+ .init = smbus_init,
.scan_bus = scan_static_bus,
.enable = i82801gx_enable,
.ops_smbus_bus = &lops_smbus_bus,
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smi.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -27,11 +27,8 @@
#include <cpu/x86/cache.h>
#include <cpu/x86/smm.h>
#include <string.h>
-#include "chip.h"
+#include "i82801gx.h"
-// Future TODO: Move to i82801gx directory
-#include "../../../northbridge/intel/i945/ich7.h"
-
extern unsigned char smm[];
extern unsigned int smm_len;
@@ -318,8 +315,12 @@
void smm_init(void)
{
+ // FIXME is this a race condition?
smm_relocate();
smm_install();
+
+ // We're done. Make sure SMIs can happen!
+ smi_set_eos();
}
void smm_lock(void)
@@ -333,3 +334,13 @@
D_LCK | G_SMRAME | C_BASE_SEG);
}
+void smm_setup_structures(void *gnvs, void *tcg, void *smi1)
+{
+ /* The GDT or coreboot table is going to live here. But a long time
+ * after we relocated the GNVS, so this is not troublesome.
+ */
+ *(u32 *)0x500 = (u32)gnvs;
+ *(u32 *)0x504 = (u32)tcg;
+ *(u32 *)0x508 = (u32)smi1;
+ outb(0xea, 0xb2);
+}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smihandler.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smihandler.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_smihandler.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -19,22 +19,24 @@
* MA 02110-1301 USA
*/
+#include <types.h>
#include <arch/io.h>
#include <arch/romcc_io.h>
#include <console/console.h>
#include <cpu/x86/cache.h>
#include <cpu/x86/smm.h>
-//#include "chip.h"
+#include "i82801gx.h"
+#include "i82801gx_power.h"
-// Future TODO: Move to i82801gx directory
-#include "../../../northbridge/intel/i945/ich7.h"
-
#define DEBUG_SMI
#define APM_CNT 0xb2
-#define APM_STS 0xb3
+#define CST_CONTROL 0x85 // 0x85 crashes the box
+#define PST_CONTROL 0x80 // 0x80 crashes the box
#define ACPI_DISABLE 0x1e
#define ACPI_ENABLE 0xe1
+#define GNVS_UPDATE 0xea
+#define APM_STS 0xb3
/* I945 */
#define SMRAM 0x9d
@@ -48,6 +50,11 @@
#define PM1_STS 0x00
#define PM1_EN 0x02
#define PM1_CNT 0x04
+#define SLP_EN (1 << 13)
+#define SLP_TYP (7 << 10)
+#define GBL_RLS (1 << 2)
+#define BM_RLD (1 << 1)
+#define SCI_EN (1 << 0)
#define PM1_TMR 0x08
#define PROC_CNT 0x10
#define LV2 0x14
@@ -56,6 +63,7 @@
#define PM2_CNT 0x20 // mobile only
#define GPE0_STS 0x28
#define GPE0_EN 0x2c
+#define PME_B0_EN (1 << 13)
#define SMI_EN 0x30
#define EL_SMI_EN (1 << 25) // Intel Quick Resume Technology
#define INTEL_USB2_EN (1 << 18) // Intel-Specific USB2 SMI logic
@@ -84,8 +92,15 @@
/* While we read PMBASE dynamically in case it changed, let's
* initialize it with a sane value
*/
-static u16 pmbase = DEFAULT_PMBASE;
+u16 pmbase = DEFAULT_PMBASE;
+/* GNVS needs to be updated by an 0xEA PM Trap (B2) after it has been located
+ * by coreboot.
+ */
+global_nvs_t *gnvs = (global_nvs_t *)0x0;
+void *tcg = (void *)0x0;
+void *smi1 = (void *)0x0;
+
/**
* @brief read and clear PM1_STS
* @return PM1_STS register
@@ -235,7 +250,6 @@
printk_debug("\n");
}
-
/* We are using PCIe accesses for now
* 1. the chipset can do it
* 2. we don't need to worry about how we leave 0xcf8/0xcfc behind
@@ -244,12 +258,10 @@
int southbridge_io_trap_handler(int smif)
{
- global_nvs_t *gnvs = (global_nvs_t *)0xc00;
-
switch (smif) {
case 0x32:
printk_debug("OS Init\n");
- //gnvs->smif = 0;
+ gnvs->smif = 0;
break;
default:
/* Not handled */
@@ -278,141 +290,337 @@
outb(reg8, pmbase + SMI_EN);
}
-/**
- * @brief Interrupt handler for SMI#
- *
- * @param smm_revision revision of the smm state save map
- */
-void southbridge_smi_handler(unsigned int node, smm_state_save_area_t *state_save)
+static void southbridge_smi_sleep(unsigned int node, smm_state_save_area_t *state_save)
{
u8 reg8;
- u16 pmctrl;
- u16 pm1_sts;
- u32 smi_sts, gpe0_sts, tco_sts;
+ u32 reg32;
+ u8 slp_typ;
+ /* FIXME: the power state on boot should be read from
+ * CMOS or even better from GNVS. Right now it's hard
+ * coded at compile time.
+ */
+ u8 s5pwr = MAINBOARD_POWER_ON_AFTER_FAIL;
- pmbase = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0x40) & 0xfffc;
- printk_spew("SMI#: pmbase = 0x%04x\n", pmbase);
+ /* First, disable further SMIs */
+ reg8 = inb(pmbase + SMI_EN);
+ reg8 &= ~SLP_SMI_EN;
+ outb(reg8, pmbase + SMI_EN);
- /* We need to clear the SMI status registers, or we won't see what's
- * happening in the following calls.
+ /* Figure out SLP_TYP */
+ reg32 = inl(pmbase + PM1_CNT);
+ printk_spew("SMI#: SLP = 0x%08x\n", reg32);
+ slp_typ = (reg32 >> 10) & 7;
+
+ /* Next, do the deed.
*/
- smi_sts = reset_smi_status();
- dump_smi_status(smi_sts);
- if (smi_sts & (1 << 21)) { // MONITOR
- global_nvs_t *gnvs = (global_nvs_t *)0xc00;
- int i;
- u32 reg32;
-
- reg32 = RCBA32(0x1e00); // TRSR - Trap Status Register
+ switch (slp_typ) {
+ case 0: printk_debug("SMI#: Entering S0 (On)\n"); break;
+ case 1: printk_debug("SMI#: Entering S1 (Assert STPCLK#)\n"); break;
+ case 5:
+ printk_debug("SMI#: Entering S3 (Suspend-To-RAM)\n");
+ /* Invalidate the cache before going to S3 */
+ wbinvd();
+ break;
+ case 6: printk_debug("SMI#: Entering S4 (Suspend-To-Disk)\n"); break;
+ case 7:
+ printk_debug("SMI#: Entering S5 (Soft Power off)\n");
#if 0
- /* Comment in for some useful debug */
- for (i=0; i<4; i++) {
- if (reg32 & (1 << i)) {
- printk_debug(" io trap #%d\n", i);
- }
+ /* Set PME_B0_EN before going to S5 */
+ reg32 = inl(pmbase + GPE0_EN);
+ reg32 |= PME_B0_EN;
+ outl(reg32, pmbase + GPE0_EN);
+#endif
+ /* Should we keep the power state after a power loss?
+ * In case the setting is "ON" or "OFF" we don't have
+ * to do anything. But if it's "KEEP" we have to switch
+ * to "OFF" before entering S5.
+ */
+ if (s5pwr == MAINBOARD_POWER_KEEP) {
+ reg8 = pcie_read_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3);
+ reg8 |= 1;
+ pcie_write_config8(PCI_DEV(0, 0x1f, 0), GEN_PMCON_3, reg8);
}
-#endif
- RCBA32(0x1e00) = reg32; // TRSR
+ break;
+ default: printk_debug("SMI#: ERROR: SLP_TYP reserved\n"); break;
+ }
- reg32 = RCBA32(0x1e10);
+ /* Write back to the SLP register to cause the originally intended
+ * event again. We need to set BIT13 (SLP_EN) though to make the
+ * sleep happen.
+ */
+ outl(reg32 | SLP_EN, pmbase + PM1_CNT);
- if ((reg32 & 0xfffc) != 0x808) {
- printk_debug(" trapped io address = 0x%x\n", reg32 & 0xfffc);
- printk_debug(" AHBE = %x\n", (reg32 >> 16) & 0xf);
- printk_debug(" read/write: %s\n", (reg32 & (1 << 24)) ? "read" :
- "write");
- }
+ /* In most sleep states, the code flow of this function ends at
+ * the line above. However, if we entered sleep state S1 and wake
+ * up again, we will continue to execute code in this function.
+ */
+ reg32 = inl(pmbase + PM1_CNT);
+ if (reg32 & SCI_EN) {
+ /* The OS is not an ACPI OS, so we set the state to S0 */
+ reg32 &= ~(SLP_EN | SLP_TYP);
+ outl(reg32, pmbase + PM1_CNT);
+ }
+}
- if (!(reg32 & (1 << 24))) {
- /* Write Cycle */
- reg32 = RCBA32(0x1e18);
- printk_debug(" iotrap written data = 0x%08x\n", reg32);
+static void southbridge_smi_apmc(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 pmctrl;
+ u8 reg8;
- }
+ /* Emulate B2 register as the FADT / Linux expects it */
- if (gnvs->smif)
- io_trap_handler(gnvs->smif); // call function smif
+ reg8 = inb(APM_CNT);
+ switch (reg8) {
+ case CST_CONTROL:
+ /* Calling this function seems to cause
+ * some kind of race condition in Linux
+ * and causes a kernel oops
+ */
+ printk_debug("C-state control\n");
+ break;
+ case PST_CONTROL:
+ /* Calling this function seems to cause
+ * some kind of race condition in Linux
+ * and causes a kernel oops
+ */
+ printk_debug("P-state control\n");
+ break;
+ case ACPI_DISABLE:
+ pmctrl = inl(pmbase + PM1_CNT);
+ pmctrl &= ~SCI_EN;
+ outl(pmctrl, pmbase + PM1_CNT);
+ printk_debug("SMI#: ACPI disabled.\n");
+ break;
+ case ACPI_ENABLE:
+ pmctrl = inl(pmbase + PM1_CNT);
+ pmctrl |= SCI_EN;
+ outl(pmctrl, pmbase + PM1_CNT);
+ printk_debug("SMI#: ACPI enabled.\n");
+ break;
+ case GNVS_UPDATE:
+ gnvs = *(global_nvs_t **)0x500;
+ tcg = *(void **)0x504;
+ smi1 = *(void **)0x508;
+ printk_debug("SMI#: Setting up structures to %p, %p, %p\n", gnvs, tcg, smi1);
+ break;
+ default:
+ printk_debug("SMI#: Unknown function APM_CNT=%02x\n", reg8);
}
+}
- if (smi_sts & (1 << 13)) { // TCO
- tco_sts = reset_tco_status();
- dump_tco_status(tco_sts);
+static void southbridge_smi_pm1(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u16 pm1_sts;
- if (tco_sts & (1 << 8)) { // BIOSWR
- u8 bios_cntl;
+ pm1_sts = reset_pm1_status();
+ dump_pm1_status(pm1_sts);
+}
- bios_cntl = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc);
+static void southbridge_smi_gpe0(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 gpe0_sts;
- if (bios_cntl & 1) {
- /* BWE is RW, so the SMI was caused by a
- * write to BWE, not by a write to the BIOS
- */
+ gpe0_sts = reset_gpe0_status();
+ dump_gpe0_status(gpe0_sts);
+}
- /* This is the place where we notice someone
- * is trying to tinker with the BIOS. We are
- * trying to be nice and just ignore it. A more
- * resolute answer would be to power down the
- * box.
- */
- printk_debug("Switching back to RO\n");
- pcie_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1));
- } /* No else for now? */
- }
+static void southbridge_smi_mc(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_EN);
+
+ /* Are periodic SMIs enabled? */
+ if ((reg32 & MCSMI_EN) == 0)
+ return;
+
+ printk_debug("Microcontroller SMI.\n");
+}
+
+
+
+static void southbridge_smi_tco(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 tco_sts;
+
+ tco_sts = reset_tco_status();
+
+ /* Any TCO event? */
+ if (!tco_sts)
+ return;
+
+ if (tco_sts & (1 << 8)) { // BIOSWR
+ u8 bios_cntl;
+
+ bios_cntl = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0xdc);
+
+ if (bios_cntl & 1) {
+ /* BWE is RW, so the SMI was caused by a
+ * write to BWE, not by a write to the BIOS
+ */
+
+ /* This is the place where we notice someone
+ * is trying to tinker with the BIOS. We are
+ * trying to be nice and just ignore it. A more
+ * resolute answer would be to power down the
+ * box.
+ */
+ printk_debug("Switching back to RO\n");
+ pcie_write_config32(PCI_DEV(0, 0x1f, 0), 0xdc, (bios_cntl & ~1));
+ } /* No else for now? */
+ } else if (tco_sts & (1 << 3)) { /* TIMEOUT */
+ /* Handle TCO timeout */
+ printk_debug("TCO Timeout.\n");
+ } else if (!tco_sts) {
+ dump_tco_status(tco_sts);
}
+}
- if (smi_sts & (1 << 8)) { // PM1
- pm1_sts = reset_pm1_status();
- dump_pm1_status(pm1_sts);
+static void southbridge_smi_periodic(unsigned int node, smm_state_save_area_t *state_save)
+{
+ u32 reg32;
+
+ reg32 = inl(pmbase + SMI_EN);
+
+ /* Are periodic SMIs enabled? */
+ if ((reg32 & PERIODIC_EN) == 0)
+ return;
+
+ printk_debug("Periodic SMI.\n");
+}
+
+static void southbridge_smi_monitor(unsigned int node, smm_state_save_area_t *state_save)
+{
+#define IOTRAP(x) (trap_sts & (1 << x))
+ u32 trap_sts, trap_cycle;
+ u32 data, mask = 0;
+ int i;
+
+ trap_sts = RCBA32(0x1e00); // TRSR - Trap Status Register
+ RCBA32(0x1e00) = trap_sts; // Clear trap(s) in TRSR
+
+ trap_cycle = RCBA32(0x1e10);
+ for (i=16; i<20; i++) {
+ if (trap_cycle & (1 << i))
+ mask |= (0xff << ((i - 16) << 2));
}
- if (smi_sts & (1 << 9)) { // GPE0
- gpe0_sts = reset_gpe0_status();
- dump_gpe0_status(gpe0_sts);
+
+ /* IOTRAP(3) SMI function call */
+ if (IOTRAP(3)) {
+ if (gnvs && gnvs->smif)
+ io_trap_handler(gnvs->smif); // call function smif
+ return;
}
- if (smi_sts & (1 << 5)) { // APM
- /* Emulate B2 register as the FADT / Linux expects it */
+ /* IOTRAP(2) currently unused
+ * IOTRAP(1) currently unused */
- reg8 = inb(0xb2);
- switch (reg8) {
- case ACPI_DISABLE:
- pmctrl = inw(pmbase + 0x04);
- pmctrl |= (1 << 0);
- outw(pmctrl, pmbase + 0x04);
- printk_debug("SMI#: ACPI disabled.\n");
- break;
- case ACPI_ENABLE:
- pmctrl = inw(pmbase + 0x04);
- pmctrl &= ~(1 << 0);
- outw(pmctrl, pmbase + 0x04);
- printk_debug("SMI#: ACPI enabled.\n");
- break;
+ /* IOTRAP(0) SMIC */
+ if (IOTRAP(0)) {
+ if (!(trap_cycle & (1 << 24))) { // It's a write
+ printk_debug("SMI1 command\n");
+ data = RCBA32(0x1e18);
+ data &= mask;
+ // if (smi1)
+ // southbridge_smi_command(data);
+ // return;
}
+ // Fall through to debug
}
- if (smi_sts & (1 << 4)) { // SLP_SMI
- u32 reg32;
+ printk_debug(" trapped io address = 0x%x\n", trap_cycle & 0xfffc);
+ for (i=0; i < 4; i++) if(IOTRAP(i)) printk_debug(" TRAP = %d\n", i);
+ printk_debug(" AHBE = %x\n", (trap_cycle >> 16) & 0xf);
+ printk_debug(" MASK = 0x%08x\n", mask);
+ printk_debug(" read/write: %s\n", (trap_cycle & (1 << 24)) ? "read" : "write");
- /* First, disable further SMIs */
- reg8 = inb(pmbase + SMI_EN);
- reg8 &= ~SLP_SMI_EN;
- outb(reg8, pmbase + SMI_EN);
+ if (!(trap_cycle & (1 << 24))) {
+ /* Write Cycle */
+ data = RCBA32(0x1e18);
+ printk_debug(" iotrap written data = 0x%08x\n", data);
+ }
+#undef IOTRAP
+}
- /* Next, do the deed, we should change
- * power on after power loss bits here
- * if we're going to S5
- */
+typedef void (*smi_handler)(unsigned int node,
+ smm_state_save_area_t *state_save);
- /* Write back to the SLP register to cause the
- * originally intended event again. We need to set BIT13
- * (SLP_EN) though to make the sleep happen.
- */
- reg32 = inl(pmbase + 0x04);
- printk_debug("SMI#: SLP = 0x%08x\n", reg32);
- printk_debug("SMI#: Powering off.\n");
- outl(reg32 | (1 << 13), pmbase + 0x04);
+smi_handler southbridge_smi[32] = {
+ NULL, // [0] reserved
+ NULL, // [1] reserved
+ NULL, // [2] BIOS_STS
+ NULL, // [3] LEGACY_USB_STS
+ southbridge_smi_sleep, // [4] SLP_SMI_STS
+ southbridge_smi_apmc, // [5] APM_STS
+ NULL, // [6] SWSMI_TMR_STS
+ NULL, // [7] reserved
+ southbridge_smi_pm1, // [8] PM1_STS
+ southbridge_smi_gpe0, // [9] GPE0_STS
+ NULL, // [10] GPI_STS
+ southbridge_smi_mc, // [11] MCSMI_STS
+ NULL, // [12] DEVMON_STS
+ southbridge_smi_tco, // [13] TCO_STS
+ southbridge_smi_periodic, // [14] PERIODIC_STS
+ NULL, // [15] SERIRQ_SMI_STS
+ NULL, // [16] SMBUS_SMI_STS
+ NULL, // [17] LEGACY_USB2_STS
+ NULL, // [18] INTEL_USB2_STS
+ NULL, // [19] reserved
+ NULL, // [20] PCI_EXP_SMI_STS
+ southbridge_smi_monitor, // [21] MONITOR_STS
+ NULL, // [22] reserved
+ NULL, // [23] reserved
+ NULL, // [24] reserved
+ NULL, // [25] EL_SMI_STS
+ NULL, // [26] SPI_STS
+ NULL, // [27] reserved
+ NULL, // [28] reserved
+ NULL, // [29] reserved
+ NULL, // [30] reserved
+ NULL // [31] reserved
+};
+
+/**
+ * @brief Interrupt handler for SMI#
+ *
+ * @param smm_revision revision of the smm state save map
+ */
+
+void southbridge_smi_handler(unsigned int node, smm_state_save_area_t *state_save)
+{
+ int i, dump = 0;
+ u32 smi_sts;
+
+ /* Update global variable pmbase */
+ pmbase = pcie_read_config16(PCI_DEV(0, 0x1f, 0), 0x40) & 0xfffc;
+
+ /* We need to clear the SMI status registers, or we won't see what's
+ * happening in the following calls.
+ */
+ smi_sts = reset_smi_status();
+
+ /* Filter all non-enabled SMI events */
+ // FIXME Double check, this clears MONITOR
+ // smi_sts &= inl(pmbase + SMI_EN);
+
+ /* Call SMI sub handler for each of the status bits */
+ for (i = 0; i < 31; i++) {
+ if (smi_sts & (1 << i)) {
+ if (southbridge_smi[i])
+ southbridge_smi[i](node, state_save);
+ else {
+ printk_debug("SMI_STS[%d] occured, but no "
+ "handler available.\n", i);
+ dump = 1;
+ }
+ }
}
+ if(dump) {
+ dump_smi_status(smi_sts);
+ }
+
}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_debug.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_debug.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_debug.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -21,16 +21,26 @@
#define EHCI_BAR 0xFEF00000
// These could be read from DEBUG_BASE (0:1d.7 R 0x5A 16bit)
#define EHCI_BAR_INDEX 0x10
+
+#define EHCI_CONFIG_FLAG 0x40
+#define EHCI_PORTSC 0x44
#define EHCI_DEBUG_OFFSET 0xA0
-static void set_debug_port(unsigned port)
+void set_debug_port(unsigned port)
{
- // Nothing for now?
+ u32 dbgctl;
+
+ printk_debug("Enabling OWNER_CNT\n");
+ dbgctl = readl(EHCI_BAR + EHCI_DEBUG_OFFSET);
+ dbgctl |= (1 << 30);
+ writel(dbgctl, EHCI_BAR + EHCI_DEBUG_OFFSET);
+
}
static void i82801gx_enable_usbdebug_direct(unsigned port)
{
pci_write_config32(PCI_DEV(0, 0x1d, 7), EHCI_BAR_INDEX, EHCI_BAR);
pci_write_config8(PCI_DEV(0, 0x1d, 7), 0x04, 0x2); // Memory Space Enable
+ set_debug_port(port);
}
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c
===================================================================
--- trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c 2009-07-21 21:44:24 UTC (rev 4455)
+++ trunk/coreboot-v2/src/southbridge/intel/i82801gx/i82801gx_usb_ehci.c 2009-07-21 21:50:34 UTC (rev 4456)
@@ -31,7 +31,7 @@
static void usb_ehci_init(struct device *dev)
{
struct resource *res;
- u8 *base;
+ u32 base;
u32 reg32;
u8 reg8;
@@ -52,9 +52,9 @@
/* Clear any pending port changes */
res = find_resource(dev, 0x10);
- base =(u8 *)res->base;
- reg32 = readl(base + 0x24) | (1 << 2);
- writel(base + 0x24, reg32);
+ base = res->base;
+ reg32 = readl((u8 *)base + 0x24) | (1 << 2);
+ writel(reg32, (u8 *)base + 0x24);
/* workaround */
reg8 = pci_read_config8(dev, 0x84);
@@ -115,7 +115,7 @@
static struct device_operations usb_ehci_ops = {
.read_resources = pci_dev_read_resources,
- .set_resources = pci_dev_set_resources,
+ .set_resources = usb_ehci_set_resources,
.enable_resources = pci_dev_enable_resources,
.init = usb_ehci_init,
.scan_bus = 0,
More information about the coreboot
mailing list