[coreboot] NEOWARE EON 4000S
Uwe Hermann
uwe at hermann-uwe.de
Tue Jul 15 00:05:11 CEST 2008
On Mon, Jul 14, 2008 at 05:25:24PM +0200, Hannes Hegewald wrote:
> Great, the irqpoll option did it!! Can we do something to make it work
> even without the irqpoll option? Maybe creating a new irq_table.c ?! I
> will also run getpir once more and compare the two files.
Yep, please do. If you want to hack on this you can also checkout
http://www.coreboot.org/Creating_Valid_IRQ_Tables
which may be useful for manually figuring out the IRQs in case
the table in svn is not correct.
> The minicom log is attached.
>
> Hannes.
>
>
>
> coreboot-2.0.0.0Normal Fr 11. Jul 18:12:37 CEST 2008 starting...
> Setting up default parameters for memory
> Sizing memory
> Probing for DIMM0
> Found DIMM0
> Page Size: 00001000
> Component Banks: 4
> Module Banks: 2
> DIMM size: 08000000
> Probing for DIMM1
> MC_BANK_CFG = 00705520
> Copying coreboot to RAM.
> Jumping to coreboot.
> coreboot-2.0.0.0Normal Fr 11. Jul 18:20:47 CEST 2008 booting...
> end 56bd01c6, start 0
> 32-bit delta 464
> calibrate_tsc 32-bit result is 464
> clocks_per_usec: 464
> Enumerating buses...
> scan_static_bus for Root Device
> northbridge.c:enable_dev()
> DEVICE_PATH_PCI_DOMAIN
> Finding PCI configuration type.
> PCI: Using configuration type 1
> PCI_DOMAIN: 0000 enabled
> PCI_DOMAIN: 0000 scanning...
> PCI: pci_scan_bus for bus 00
> northbridge.c:enable_dev()
> device path type 2
> PCI: 00:00.0 [1078/0001] ops
> PCI: 00:00.0 [1078/0001] enabled
> PCI: devfn 0x8, bad id 0xffffffff
> PCI: devfn 0x10, bad id 0xffffffff
> PCI: devfn 0x18, bad id 0xffffffff
> PCI: devfn 0x20, bad id 0xffffffff
> PCI: devfn 0x28, bad id 0xffffffff
> PCI: devfn 0x30, bad id 0xffffffff
> PCI: devfn 0x38, bad id 0xffffffff
> PCI: devfn 0x40, bad id 0xffffffff
> PCI: devfn 0x48, bad id 0xffffffff
> PCI: devfn 0x50, bad id 0xffffffff
> PCI: devfn 0x58, bad id 0xffffffff
> PCI: devfn 0x60, bad id 0xffffffff
> PCI: devfn 0x68, bad id 0xffffffff
> PCI: devfn 0x70, bad id 0xffffffff
> PCI: 00:0f.0 [10ec/8139] enabled
> PCI: devfn 0x80, bad id 0xffffffff
> PCI: devfn 0x88, bad id 0xffffffff
> PCI: 00:12.0 [1078/0100] bus ops
> PCI: 00:12.0 [1078/0100] enabled
> PCI: 00:12.1 [1078/0101] disabled
> PCI: 00:12.2 [1078/0102] bus ops
> PCI: 00:12.2 [1078/0102] enabled
> PCI: 00:12.3 [1078/0103] enabled
> PCI: 00:12.4 [1078/0104] ops
> PCI: 00:12.4 [1078/0104] enabled
> PCI: devfn 0x95, bad id 0xffffffff
> PCI: devfn 0x96, bad id 0xffffffff
> PCI: devfn 0x97, bad id 0xffffffff
> PCI: 00:13.0 [0e11/a0f8] enabled
> PCI: devfn 0xa0, bad id 0xffffffff
> PCI: devfn 0xa8, bad id 0xffffffff
> PCI: devfn 0xb0, bad id 0xffffffff
> PCI: devfn 0xb8, bad id 0xffffffff
> PCI: devfn 0xc0, bad id 0xffffffff
> PCI: devfn 0xc8, bad id 0xffffffff
> PCI: devfn 0xd0, bad id 0xffffffff
> PCI: devfn 0xd8, bad id 0xffffffff
> PCI: devfn 0xe0, bad id 0xffffffff
> PCI: devfn 0xe8, bad id 0xffffffff
> PCI: devfn 0xf0, bad id 0xffffffff
> PCI: devfn 0xf8, bad id 0xffffffff
> scan_static_bus for PCI: 00:12.0
> malloc Enter, size 1100, free_mem_ptr 0001a000
> malloc 0x0001a000
> PNP: 002e.0 disabled
> PNP: 002e.1 enabled
> PNP: 002e.2 enabled
> PNP: 002e.e enabled
> PNP: 002e.4 enabled
> PNP: 002e.5 enabled
> PNP: 002e.6 enabled
> PNP: 002e.7 enabled
> PNP: 002e.8 enabled
> PNP: 002e.3 enabled
> scan_static_bus for PCI: 00:12.0 done
> scan_static_bus for PCI: 00:12.2
> scan_static_bus for PCI: 00:12.2 done
> PCI: pci_scan_bus returning with max=000
> scan_static_bus for Root Device done
> done
> Allocating resources...
> Reading resources...
> Root Device compute_allocate_io: base: 00000400 size: 00000000 align: 0 gran: 0
> Root Device read_resources bus 0 link: 0
> northbridge.c:pci_domain_read_resources()
> PCI_DOMAIN: 0000 read_resources bus 0 link: 0
> PCI_DOMAIN: 0000 read_resources bus 0 link: 0 done
> Root Device read_resources bus 0 link: 0 done
> PCI: 00:0f.0 10 * [0x00000400 - 0x000004ff] io
> PCI: 00:12.2 20 * [0x00000800 - 0x0000087f] io
> Root Device compute_allocate_io: base: 00000880 size: 00000480 align: 8 gran: 0 done
> Root Device compute_allocate_mem: base: 00000000 size: 00000000 align: 0 gran: 0
> Root Device read_resources bus 0 link: 0
> Root Device read_resources bus 0 link: 0 done
> PCI: 00:12.4 10 * [0x00000000 - 0x00000fff] mem
> PCI: 00:13.0 10 * [0x00001000 - 0x00001fff] mem
> PCI: 00:0f.0 14 * [0x00002000 - 0x000020ff] mem
> PCI: 00:12.3 10 * [0x00003000 - 0x0000307f] mem
> Root Device compute_allocate_mem: base: 00003080 size: 00003080 align: 12 gran: 0 done
> Done reading resources.
> Setting resources...
> Root Device compute_allocate_io: base: 00001000 size: 00000480 align: 8 gran: 0
> Root Device read_resources bus 0 link: 0
> Root Device read_resources bus 0 link: 0 done
> PCI: 00:0f.0 10 * [0x00001000 - 0x000010ff] io
> PCI: 00:12.2 20 * [0x00001400 - 0x0000147f] io
> Root Device compute_allocate_io: base: 00001480 size: 00000480 align: 8 gran: 0 done
> Root Device compute_allocate_mem: base: febfc000 size: 00003080 align: 12 gran: 0
> Root Device read_resources bus 0 link: 0
> Root Device read_resources bus 0 link: 0 done
> PCI: 00:12.4 10 * [0xfebfc000 - 0xfebfcfff] mem
> PCI: 00:13.0 10 * [0xfebfd000 - 0xfebfdfff] mem
> PCI: 00:0f.0 14 * [0xfebfe000 - 0xfebfe0ff] mem
> PCI: 00:12.3 10 * [0xfebff000 - 0xfebff07f] mem
> Root Device compute_allocate_mem: base: febff080 size: 00003080 align: 12 gran: 0 done
> Root Device assign_resources, bus 0 link: 0
> BC_DRAM_TOP = 0x07dfffff
> MC_GBASE_ADD = 0x000000fc
> I would set ram size to 126 Mbytes
> PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
> PCI: 00:0f.0 10 <- [0x0000001000 - 0x00000010ff] size 0x00000100 gran 0x08 io
> PCI: 00:0f.0 14 <- [0x00febfe000 - 0x00febfe0ff] size 0x00000100 gran 0x08 mem
> PCI: 00:12.2 20 <- [0x0000001400 - 0x000000147f] size 0x00000080 gran 0x07 io
> PCI: 00:12.3 10 <- [0x00febff000 - 0x00febff07f] size 0x00000080 gran 0x07 mem
> PCI: 00:12.4 10 <- [0x00febfc000 - 0x00febfcfff] size 0x00001000 gran 0x0c mem
> PCI: 00:13.0 10 <- [0x00febfd000 - 0x00febfdfff] size 0x00001000 gran 0x0c mem
> PCI_DOMAIN: 0000 assign_resources, bus 0 link: 0
> Root Device assign_resources, bus 0 link: 0
> Done setting resources.
> Done allocating resources.
> Enabling resources...
> PCI: 00:00.0 cmd <- 07
> PCI: 00:0f.0 subsystem <- 00/00
> PCI: 00:0f.0 cmd <- 03
> PCI: 00:12.0 cmd <- 0f
> PNP: 002e.e missing enable_resources
> PCI: 00:12.2 cmd <- 01
> PCI: 00:12.3 subsystem <- 00/00
> PCI: 00:12.3 cmd <- 02
> PCI: 00:12.4 cmd <- 02
> PCI: 00:13.0 subsystem <- 00/00
> PCI: 00:13.0 cmd <- 02
> done.
> Initializing devices...
> Root Device init
> PCI: 00:00.0 init
> northbridge: northbridge_init()
> Calling enable_cache()
> PCI: 00:0f.0 init
> PCI: 00:12.0 init
> PNP: 002e.1 init
> PNP: 002e.2 init
> PNP: 002e.4 init
> PNP: 002e.5 init
> PNP: 002e.6 init
> Keyboard init...
> PNP: 002e.7 init
> PNP: 002e.8 init
> PCI: 00:12.2 init
> Primary IDE interface enabled
> Secondary IDE interface disabled
> PCI: 00:12.3 init
> PCI: 00:12.4 init
> Setting up video mode 640x480 with 31500000 Hz clock
> PCI: 00:13.0 init
> PNP: 002e.3 init
> Devices initialized
> Copying IRQ routing tables to 0xf0000...done.
> Verifing copy of IRQ routing tables at 0xf0000...done
> Checking IRQ routing table consistency...
> check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
> done.
> PIR Entry 0 Dev/Fn: 7 Slot: 1
> INT: A link: 2 bitmap: deb8 IRQ: 3
> INT: B link: 3 bitmap: deb8 IRQ: 4
> INT: C link: 4 bitmap: deb8 IRQ: 5
> INT: D link: 1 bitmap: deb8 IRQ: 7
> PIR Entry 1 Dev/Fn: F Slot: 2
> INT: A link: 3 bitmap: deb8 IRQ: 4
> INT: B link: 4 bitmap: deb8 IRQ: 5
> INT: C link: 1 bitmap: deb8 IRQ: 7
> INT: D link: 2 bitmap: deb8 IRQ: 3
> Assigning IRQ 4 to 0:f.0
> Readback = 4
> pci_level_irq: current ints are 0x0
> pci_level_irq: try to set ints 0x10
> PIR Entry 2 Dev/Fn: 13 Slot: 0
> INT: A link: 1 bitmap: deb8 IRQ: 7
> INT: B link: 0 bitmap: deb8 not routed
> INT: C link: 0 bitmap: deb8 not routed
> INT: D link: 0 bitmap: deb8 not routed
> Assigning IRQ 7 to 0:13.0
> Readback = 7
> pci_level_irq: current ints are 0x10
> pci_level_irq: try to set ints 0x90
> PIRQ1: 7
> PIRQ2: 3
> PIRQ3: 4
> PIRQ4: 5
> Moving GDT to 0x500...ok
> Adjust low_table_end from 0x00000530 to 0x00001000
> Adjust rom_table_end from 0x000f0400 to 0x00100000
> Wrote coreboot table at: 00000530 - 00000748 checksum e10a
>
> Welcome to elfboot, the open sourced starter.
> January 2002, Eric Biederman.
> Version 1.3
>
> rom_stream: 0xfffc0000 - 0xfffcffff
> Found ELF candidate at offset 0
> header_offset is 0
> Try to load at offset 0x0
> malloc Enter, size 32, free_mem_ptr 0001a44c
> malloc 0x0001a44c
> New segment addr 0x100000 size 0x33ae0 offset 0xc0 filesize 0xa648
> (cleaned up) New segment addr 0x100000 size 0x33ae0 offset 0xc0 filesize 0xa648
> lb: [0x0000000000004000, 0x000000000001e000)
> malloc Enter, size 32, free_mem_ptr 0001a46c
> malloc 0x0001a46c
> New segment addr 0x133ae0 size 0x48 offset 0xa720 filesize 0x48
> (cleaned up) New segment addr 0x133ae0 size 0x48 offset 0xa720 filesize 0x48
> lb: [0x0000000000004000, 0x000000000001e000)
> Dropping non PT_LOAD segment
> Dropping non PT_LOAD segment
> Loading Segment: addr: 0x0000000000100000 memsz: 0x0000000000033ae0 filesz: 0x000000000000a648
> [ 0x0000000000100000, 000000000010a648, 0x0000000000133ae0) <- 00000000000000c0
> Clearing Segment: addr: 0x000000000010a648 memsz: 0x0000000000029498
> Loading Segment: addr: 0x0000000000133ae0 memsz: 0x0000000000000048 filesz: 0x0000000000000048
> [ 0x0000000000133ae0, 0000000000133b28, 0x0000000000133b28) <- 000000000000a720
> Loaded segments
> verified segments
> closed down stream
> Jumping to boot code at 0x10854c
> entry = 0x0010854c
> lb_start = 0x00004000
> lb_size = 0x0001a000
> adjust = 0x07de2000
> buffer = 0x07dcc000
> elf_boot_notes = 0x00014140
> adjusted_boot_notes = 0x07df6140
> FILO version 0.5.5 (root at zendeb) Fri Jul 11 18:19:27 CEST 2008
> boot: hda1:/boot/vmlinuz root=/dev/hda1 console=tty0 console=ttyS0,115200 irqpoll
> hda: LBA 80GB: MAXTOR 6L080J4
> Mounted EXT2 filesystem
> Found Linux version 2.6.24.4 (root at crux) #2 SMP Fri May 23 11:56:57 CEST 2008 bzImage.
> Loading kernel... ok
> Jumping to entry point...
> Linux version 2.6.24.4 (root at crux) (gcc version 4.2.4 (CRUX)) #2 SMP Fri May 23 11:56:57 CEST 2008
> BIOS-provided physical RAM map:
> BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
> BIOS-e820: 0000000000100000 - 0000000007e00000 (usable)
> 126MB LOWMEM available.
> Zone PFN ranges:
> DMA 0 -> 4096
> Normal 4096 -> 32256
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0 -> 32256
> DMI not present or invalid.
> Allocating PCI resources starting at 10000000 (gap: 07e00000:f8200000)
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32004
> Kernel command line: root=/dev/hda1 console=tty0 console=ttyS0,115200 irqpoll
> Misrouted IRQ fixup and polling support enabled
> This may significantly impact system performance
> No local APIC present or hardware disabled
> Initializing CPU#0
> PID hash table entries: 512 (order: 9, 2048 bytes)
> Detected 300.677 MHz processor.
> Console: colour dummy device 80x25
> console [tty0] enabled
> console [ttyS0] enabled
> Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
> Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
> Memory: 123264k/129024k available (2644k kernel code, 5260k reserved, 888k data, 208k init, 0k highmem)
> virtual kernel memory layout:
> fixmap : 0xfffb5000 - 0xfffff000 ( 296 kB)
> vmalloc : 0xc8800000 - 0xfffb3000 ( 887 MB)
> lowmem : 0xc0000000 - 0xc7e00000 ( 126 MB)
> .init : 0xc047a000 - 0xc04ae000 ( 208 kB)
> .data : 0xc03950d0 - 0xc04732f4 ( 888 kB)
> .text : 0xc0100000 - 0xc03950d0 (2644 kB)
> Checking if this processor honours the WP bit even in supervisor mode... Ok.
> Calibrating delay using timer specific routine.. 626.79 BogoMIPS (lpj=1253584)
> Mount-cache hash table entries: 512
> Working around Cyrix MediaGX virtual DMA bugs.
> Enable Memory-Write-back mode on Cyrix/NSC processor.
> Enable Memory access reorder on Cyrix/NSC processor.
> Enable Incrementor on Cyrix/NSC processor.
> Compat vDSO mapped to ffffe000.
> Checking 'hlt' instruction... OK.
> SMP alternatives: switching to UP code
> Freeing SMP alternatives: 14k freed
> ACPI: Core revision 20070126
> ACPI Exception (tbxface-0629): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126]
> ACPI: Unable to load the System Description Tables
> CPU0: NSC Geode(TM) Integrated Processor by National Semi stepping 02
> SMP motherboard not detected.
> Local APIC not detected. Using dummy APIC emulation.
> Brought up 1 CPUs
> net_namespace: 64 bytes
> NET: Registered protocol family 16
> EISA bus registered
> PCI: Using configuration type 1
> Setting up standard PCI resources
> ACPI: Interpreter disabled.
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI: disabled
> SCSI subsystem initialized
> PCI: Probing PCI hardware
> PCI: Using IRQ router NatSemi [1078/0100] at 0000:00:12.0
> Time: tsc clocksource has been installed.
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 4096 (order: 3, 32768 bytes)
> TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 4096 bind 4096)
> TCP reno registered
> microcode: CPU0 not a capable Intel processor
> IA-32 Microcode Update Driver: v1.14a <tigran at aivazian.fsnet.co.uk>
> JFS: nTxBlock = 964, nTxLock = 7712
> SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
> SGI XFS Quota Management subsystem
> io scheduler noop registered
> io scheduler deadline registered (default)
> PCI: Fixup for MediaGX/Geode Slave Disconnect Boundary (0x41=0x10)
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> loop: module loaded
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> CS5530: IDE controller (0x1078:0x0102 rev 0x00) at PCI slot 0000:00:12.2
> CS5530: not 100% native mode: will probe irqs later
> ide0: BM-DMA at 0x1400-0x1407, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x1408-0x140f, BIOS settings: hdc:pio, hdd:pio
> Clocksource tsc unstable (delta = -161502172 ns)
> Time: pit clocksource has been installed.
> hda: MAXTOR 6L080J4, ATA DISK drive
> hda: UDMA/33 mode selected
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> hda: max request size: 128KiB
> hda: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=65535/16/63
> hda: cache flushes supported
> hda: hda1 hda2 hda3
> Driver 'sd' needs updating - please use bus_type methods
> Driver 'sr' needs updating - please use bus_type methods
> Fusion MPT base driver 3.04.06
> Copyright (c) 1999-2007 LSI Corporation
> Fusion MPT SPI Host driver 3.04.06
> PNP: No PS/2 controller found. Probing ports directly.
> serio: i8042 KBD port at 0x60,0x64 irq 1
> serio: i8042 AUX port at 0x60,0x64 irq 12
> mice: PS/2 mouse device common for all mice
> EISA: Probing bus 0 at eisa.0
> Cannot allocate resource for EISA slot 1
> EISA: Detected 0 cards.
> TCP cubic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> Using IPI No-Shortcut mode
> kjournald starting. Commit interval 5 seconds
> EXT3-fs: mounted filesystem with ordered data mode.
> VFS: Mounted root (ext3 filesystem) readonly.
> Freeing unused kernel memory: 208k freed
> INIT: version 2.86 booting
> The system is coming up. Please wait.
> 8139too Fast Ethernet driver 0.9.28
> PCI: Found IRQ 5 for device 0000:00:0f.0
> IRQ routing conflict for 0000:00:0f.0, have irq 4, want irq 5
> eth0: RealTek RTL8139 at 0xc88a4000, 00:e0:c5:6e:52:16, IRQ 4
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
> PCI: Found IRQ 3 for device 0000:00:13.0
> IRQ routing conflict for 0000:00:13.0, have irq 7, want irq 3
> ohci_hcd 0000:00:13.0: OHCI Host Controller
> ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
> ohci_hcd 0000:00:13.0: irq 7, io mem 0xfebfd000
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 2 ports detected
> /dev/hda1 has gone 25809 days without being checked, check forced.
> /sbin/fsck.xfs: XFS file system.
> EXT3 FS on hda1, internal journal
> XFS mounting filesystem hda2
> Adding 265064k swap on /dev/hda3. Priority:-1 extents:1 across:265064k
> hostname: crux
> font: default
> keyboard: de-latin1
> INIT: Entering runlevel: 2
> starting services: sysklogd net fcron sshd samba led
>
>
> CRUX (crux) (ttyS0)
>
> crux login: root
> Password:
Uwe.
--
http://www.hermann-uwe.de | http://www.holsham-traders.de
http://www.crazy-hacks.org | http://www.unmaintained-free-software.org
More information about the coreboot
mailing list