[coreboot] Fam10h support for Tyan S2912-E

[Arne Georg Gleditsch]

Arne Georg Gleditsch <arne.gleditsch at dolphinics.no> writes:
> Here you go.  My current status is as follows:
>
> * SATA controller: works, but only if vendor BIOS is allowed to run once
>   after poweron.  Not sure what the issue can be here, since the
>   controller seems to work flawlessly both in FILO and Linux when the
>   vendor BIOS is replaced with coreboot in flight and hard reset is
>   applied.

As an additional data point, this is what the Linux kernel (here loaded
from IDE cdrom) has to say about the SATA ports when they're not
working:

[  359.158098] sata_nv 0000:00:06.0: version 3.3
[  359.158124] PCI: Setting latency timer of device 0000:00:06.0 to 64
[  359.158182] ata1: SATA max UDMA/133 cmd 0x0000000000012cc0 ctl 0x0000000000013032 bmdma 0x0000000000012c90 irq 20
[  359.158319] ata2: SATA max UDMA/133 cmd 0x0000000000012cd0 ctl 0x0000000000013042 bmdma 0x0000000000012c98 irq 20
[  359.158435] scsi0 : sata_nv
[  359.473303] ata1: SATA link down (SStatus 0 SControl 300)
[  359.484085] ATA: abnormal status 0x7F on port 0x0000000000012cc7
[  359.484172] scsi1 : sata_nv
[  359.796672] ata2: SATA link down (SStatus 0 SControl 300)
[  359.807446] ATA: abnormal status 0x7F on port 0x0000000000012cd7
[  359.807572] PCI: Setting latency timer of device 0000:00:06.1 to 64
[  359.807601] ata3: SATA max UDMA/133 cmd 0x0000000000012ce0 ctl 0x0000000000013052 bmdma 0x0000000000012ca0 irq 23
[  359.807736] ata4: SATA max UDMA/133 cmd 0x0000000000012cf0 ctl 0x0000000000013062 bmdma 0x0000000000012ca8 irq 23
[  359.807849] scsi2 : sata_nv
[  360.120043] ata3: SATA link down (SStatus 0 SControl 300)
[  360.130812] ATA: abnormal status 0x7F on port 0x0000000000012ce7
[  360.130895] scsi3 : sata_nv
[  360.443414] ata4: SATA link down (SStatus 0 SControl 300)
[  360.454183] ATA: abnormal status 0x7F on port 0x0000000000012cf7
[  360.454290] PCI: Setting latency timer of device 0000:00:06.2 to 64
[  360.454315] ata5: SATA max UDMA/133 cmd 0x0000000000012d00 ctl 0x0000000000013072 bmdma 0x0000000000012cb0 irq 21
[  360.454448] ata6: SATA max UDMA/133 cmd 0x0000000000013000 ctl 0x0000000000013082 bmdma 0x0000000000012cb8 irq 21
[  360.454559] scsi4 : sata_nv
[  360.766785] ata5: SATA link down (SStatus 0 SControl 300)
[  360.777557] ATA: abnormal status 0x7F on port 0x0000000000012d07
[  360.777640] scsi5 : sata_nv
[  361.090155] ata6: SATA link down (SStatus 0 SControl 300)
[  361.100932] ATA: abnormal status 0x7F on port 0x0000000000013007

-- 
								Arne.