[LinuxBIOS] r2638 - in trunk/LinuxBIOSv2: src/cpu/amd/model_lx src/mainboard/digitallogic/msm800sev targets/digitallogic/msm800sev
svn at openbios.org
svn at openbios.org
Sat May 5 05:54:14 CEST 2007
Author: rminnich
Date: 2007-05-05 05:54:13 +0200 (Sat, 05 May 2007)
New Revision: 2638
Modified:
trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cache_as_ram.inc
trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb
trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb
trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c
trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c
trunk/LinuxBIOSv2/targets/digitallogic/msm800sev/Config.lb
Log:
This is the final patch to enable the msm800sev to build. This patch
adds a symbol to the model_lx/cache_as_ram.inc, and modifies some
files in the mainboard directory. This patch has been tested but there
is a remaining problem which I am tracking down. Expect one more patch
to "get it all working".
Signed-off-by: Ronald G. Minnich <rminnich at gmail.com>
Acked-by: Stefan Reinauer <stepan at coresystems.de>
Modified: trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cache_as_ram.inc
===================================================================
--- trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cache_as_ram.inc 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/src/cpu/amd/model_lx/cache_as_ram.inc 2007-05-05 03:54:13 UTC (rev 2638)
@@ -177,6 +177,7 @@
/* Go do early init and memory setup */
call cache_as_ram_main
+done_cache_as_ram_main:
/* If you wanted to maintain the stack in memory you would need to set the tags as dirty
so the wbinvd would push out the old stack contents to memory */
Modified: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Config.lb 2007-05-05 03:54:13 UTC (rev 2638)
@@ -44,31 +44,22 @@
driver mainboard.o
-if HAVE_PIRQ_TABLE object irq_tables.o end
-#object reset.o
-
-##
-## Romcc output
-##
-makerule ./failover.E
- depends "$(MAINBOARD)/failover.c ./romcc"
- action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+if HAVE_PIRQ_TABLE
+ object irq_tables.o
end
-makerule ./failover.inc
- depends "$(MAINBOARD)/failover.c ./romcc"
- action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/failover.c -o $@"
+if USE_DCACHE_RAM
+ #compile cache_as_ram.c to auto.inc
+ makerule ./cache_as_ram_auto.inc
+ depends "$(MAINBOARD)/cache_as_ram_auto.c option_table.h"
+ action "$(CC) -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/cache_as_ram_auto.c -Os -nostdinc -nostdlib -fno-builtin -Wall -c -S -o $@"
+ action "perl -e 's/.rodata/.rom.data/g' -pi $@"
+ action "perl -e 's/.text/.section .rom.text/g' -pi $@"
+ end
end
-makerule ./auto.E
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
- action "./romcc -E -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
-end
-makerule ./auto.inc
- depends "$(MAINBOARD)/auto.c option_table.h ./romcc"
- action "./romcc -mcpu=p2 -O -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/auto.c -o $@"
-end
+
##
## Build our 16 bit and 32 bit linuxBIOS entry code
##
@@ -104,7 +95,7 @@
###
if USE_FALLBACK_IMAGE
ldscript /arch/i386/lib/failover.lds
- mainboardinit ./failover.inc
+# mainboardinit ./failover.inc
end
###
@@ -115,8 +106,12 @@
## Setup RAM
##
mainboardinit cpu/x86/fpu/enable_fpu.inc
-mainboardinit ./auto.inc
+if USE_DCACHE_RAM
+ mainboardinit cpu/amd/model_lx/cache_as_ram.inc
+ mainboardinit ./cache_as_ram_auto.inc
+end
+
##
## Include the secondary Configuration files
##
@@ -124,57 +119,88 @@
config chip.h
chip northbridge/amd/lx
- # they keep changing this. 0:f.0 5c.w to see where it is
- register "irqmap" = "0xbaba"
- register "setupflash" = "0"
+ device pci_domain 0 on
+ device pci 1.0 on end
+ device pci 1.1 on end
+ chip southbridge/amd/cs5536
+ # IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK
+ # SIRQ Mode = Active(Quiet) mode. Save power....
+ # Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
+ # How to get these? Boot linux and do this:
+ # rdmsr 0x51400025
+ register "lpc_serirq_enable" = "0x000010da"
+ # rdmsr 0x5140004e -- polairy is high 16 bits of low 32 bits
+ register "lpc_serirq_polarity" = "0x0000EF25"
+ # mode is high 10 bits (determined from code)
+ register "lpc_serirq_mode" = "1"
+ # Don't yet know how to find this.
+ register "enable_gpio_int_route" = "0x0D0C0700"
+ register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
+ register "enable_USBP4_device" = "0" #0: host, 1:device
+ register "enable_USBP4_overcurrent" = "0" #0:off, xxxx:overcurrent setting CS5536 Data Book (pages 380-381)
+ register "com1_enable" = "0"
+ register "com1_address" = "0x3F8"
+ register "com1_irq" = "4"
+ register "com2_enable" = "0"
+ register "com2_address" = "0x2F8"
+ register "com2_irq" = "3"
+ register "unwanted_vpci[0]" = "0" # End of list has a zero
+ device pci f.0 on # ISA Bridge
+ chip superio/winbond/w83627hf
+ device pnp 2e.0 off # Floppy
+ io 0x60 = 0x3f0
+ irq 0x70 = 6
+ drq 0x74 = 2
+ end
+ device pnp 2e.1 off # Parallel Port
+ io 0x60 = 0x378
+ irq 0x70 = 7
+ end
+ device pnp 2e.2 on # Com1
+ io 0x60 = 0x3f8
+ irq 0x70 = 4
+ end
+ device pnp 2e.3 on # Com2
+ io 0x60 = 0x2f8
+ irq 0x70 = 3
+ end
+ device pnp 2e.5 on # Keyboard
+ io 0x60 = 0x60
+ io 0x62 = 0x64
+ irq 0x70 = 1
+ irq 0x72 = 12
+ end
+ device pnp 2e.6 off # CIR
+ io 0x60 = 0x100
+ end
+ device pnp 2e.7 off # GAME_MIDI_GIPO1
+ io 0x60 = 0x220
+ io 0x62 = 0x300
+ irq 0x70 = 9
+ end
+ device pnp 2e.8 off end # GPIO2
+ device pnp 2e.9 off end # GPIO3
+ device pnp 2e.a off end # ACPI
+ device pnp 2e.b on # HW Monitor
+ io 0x60 = 0x290
+ irq 0x70 = 5
+ end
+ end
+ end
+ device pci f.1 on end # Flash controller
+ device pci f.2 on end # IDE controller
+ device pci f.3 on end # Audio
+ device pci f.4 on end # OHCI
+ device pci f.5 on end # EHCI
+ end
+ end
+
+ # APIC cluster is late CPU init.
device apic_cluster 0 on
chip cpu/amd/model_lx
device apic 0 on end
end
end
- device pci_domain 0 on
- device pci 1.0 on end
- device pci 1.1 on end
- chip southbridge/amd/cs5536_lx
- register "isa_irq" = "0"
- #register "flash_irq" = "14"
- ## IDE IRQ
- register "enable_ide_irq" = "0"
-
- register "audio_irq" = "5"
- register "usb_irq" = "7"
-
- register "uart0_irq" = "0"
- register "uart1_irq" = "4"
-
- ## PCI INTA ... INTD and their GPIO pins
- ## int==0: disable
- register "pci_int[0]" = "0"
- register "pci_int[1]" = "10"
- register "pci_int[2]" = "0"
- register "pci_int[3]" = "0"
- register "pci_int_pin[0]" = "0"
- register "pci_int_pin[1]" = "7"
- register "pci_int_pin[2]" = "0"
- register "pci_int_pin[3]" = "0"
-
-
- # Keyboard Emulation Logic IRQs
- # Enable keyboard IRQ2
- register "enable_kel_keyb_irq" = "0"
- # Enable mouse IRQ12
- register "enable_kel_mouse_irq" = "0"
- # Configure KEL Emulation IRQ, 0 to disable
- register "kel_emul_irq" = "0"
-
- device pci f.0 on end # ISA Bridge
- device pci f.1 on end # Flash controller
- device pci f.2 off end # IDE controller
- device pci f.3 on end # Audio
- device pci f.4 on end # OHCI
- device pci f.5 on end # EHCI
- end
- end
end
Modified: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/Options.lb 2007-05-05 03:54:13 UTC (rev 2638)
@@ -21,7 +21,9 @@
uses ROM_SECTION_SIZE
uses ROM_SECTION_OFFSET
uses CONFIG_ROM_PAYLOAD_START
+uses CONFIG_COMPRESSED_PAYLOAD_NRV2B
uses CONFIG_COMPRESSED_PAYLOAD_LZMA
+uses CONFIG_PRECOMPRESSED_PAYLOAD
uses PAYLOAD_SIZE
uses _ROMBASE
uses _RAMBASE
@@ -43,18 +45,20 @@
uses CONFIG_CONSOLE_VGA
uses CONFIG_PCI_ROM_RUN
uses CONFIG_VIDEO_MB
+uses USE_DCACHE_RAM
+uses DCACHE_RAM_BASE
+uses DCACHE_RAM_SIZE
-default CONFIG_VIDEO_MB=8
-
-
## ROM_SIZE is the size of boot ROM that this board will use.
-default ROM_SIZE = 1024*1024
+default ROM_SIZE = 256*1024
###
### Build options
###
-#default CONFIG_CONSOLE_VGA=1
-#default CONFIG_PCI_ROM_RUN=0
+default CONFIG_CONSOLE_VGA=0
+default CONFIG_VIDEO_MB=8
+default CONFIG_PCI_ROM_RUN=0
+
##
## Build code for the fallback boot
##
@@ -78,9 +82,8 @@
##
## Build code to export a programmable irq routing table
##
-default HAVE_PIRQ_TABLE=0
+default HAVE_PIRQ_TABLE=1
default IRQ_SLOT_COUNT=6
-
#object irq_tables.o
##
@@ -97,6 +100,13 @@
default FALLBACK_SIZE = 131072
##
+## enable CACHE_AS_RAM specifics
+##
+default USE_DCACHE_RAM=1
+default DCACHE_RAM_BASE=0xc8000
+default DCACHE_RAM_SIZE=0x08000
+
+##
## Use a small 8K stack
##
default STACK_SIZE=0x2000
Modified: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/irq_tables.c 2007-05-05 03:54:13 UTC (rev 2638)
@@ -1,3 +1,4 @@
+#if 0
/* This file was generated by getpir.c, do not modify!
(but if you do, please run checkpir on it to verify)
* Contains the IRQ Routing Table dumped directly from your memory, which BIOS sets up
@@ -58,3 +59,107 @@
{
return copy_pirq_routing_table(addr);
}
+#endif
+/*
+* This file is part of the LinuxBIOS project.
+*
+* Copyright (C) 2007 Advanced Micro Devices
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License version 2 as
+* published by the Free Software Foundation.
+*
+* This program is distributed in the hope that it will be useful,
+* but WITHOUT ANY WARRANTY; without even the implied warranty of
+* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+* GNU General Public License for more details.
+*
+* You should have received a copy of the GNU General Public License
+* along with this program; if not, write to the Free Software
+* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+*/
+
+#include <arch/pirq_routing.h>
+#include <console/console.h>
+#include <arch/io.h>
+#include <arch/pirq_routing.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
+
+/* Platform IRQs */
+#define PIRQA 11
+#define PIRQB 5
+#define PIRQC 10
+#define PIRQD 10
+
+/* Map */
+#define M_PIRQA (1 << PIRQA) /* Bitmap of supported IRQs */
+#define M_PIRQB (1 << PIRQB) /* Bitmap of supported IRQs */
+#define M_PIRQC (1 << PIRQC) /* Bitmap of supported IRQs */
+#define M_PIRQD (1 << PIRQD) /* Bitmap of supported IRQs */
+
+/* Link */
+#define L_PIRQA 1 /* Means Slot INTx# Connects To Chipset INTA# */
+#define L_PIRQB 2 /* Means Slot INTx# Connects To Chipset INTB# */
+#define L_PIRQC 3 /* Means Slot INTx# Connects To Chipset INTC# */
+#define L_PIRQD 4 /* Means Slot INTx# Connects To Chipset INTD# */
+
+const struct irq_routing_table intel_irq_routing_table = {
+ PIRQ_SIGNATURE, /* u32 signature */
+ PIRQ_VERSION, /* u16 version */
+ 32+16*IRQ_SLOT_COUNT, /* there can be total 6 devices on the bus */
+ 0x00, /* Where the interrupt router lies (bus) */
+ (0x0F<<3)|0x0, /* Where the interrupt router lies (dev) */
+ 0x00, /* IRQs devoted exclusively to PCI usage */
+ 0x100B, /* Vendor */
+ 0x002B, /* Device */
+ 0, /* Crap (miniport) */
+ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */
+ 0x00, /* u8 checksum , this has to set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */
+ {
+ /* If you change the number of entries, change the IRQ_SLOT_COUNT above! */
+ /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */
+ {0x00,(0x01<<3)|0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00, 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
+ {0x00,(0x0F<<3)|0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
+ {0x00,(0x0C<<3)|0x0, {{L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}}, 0x1, 0x0}, /* slot1 */
+ {0x00,(0x0D<<3)|0x0, {{L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}}, 0x2, 0x0}, /* slot2 */
+ {0x00,(0x0A<<3)|0x0, {{L_PIRQD, M_PIRQD}, {L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}}, 0x3, 0x0}, /* slot3 */
+ {0x00,(0x0B<<3)|0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB}, {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x4, 0x0}, /* slot4 */
+ }
+};
+
+
+
+unsigned long write_pirq_routing_table(unsigned long addr){
+ int i, j, k, num_entries;
+ unsigned int pirq[4];
+ uint16_t chipset_irq_map;
+ uint32_t pciAddr, pirtable_end;
+ struct irq_routing_table *pirq_tbl;
+
+ pirtable_end = copy_pirq_routing_table(addr);
+
+ /* Set up chipset IRQ steering */
+ pciAddr = 0x80000000 | (CHIPSET_DEV_NUM << 11) | 0x5C;
+ chipset_irq_map = (PIRQD << 12 | PIRQC << 8 | PIRQB << 4 | PIRQA);
+ printk_debug("%s(%08X, %04X)\n", __FUNCTION__, pciAddr, chipset_irq_map);
+ outl(pciAddr & ~3, 0xCF8);
+ outl(chipset_irq_map, 0xCFC);
+
+ pirq_tbl = (struct irq_routing_table *)(addr);
+ num_entries = (pirq_tbl->size - 32)/16;
+
+ /* Set PCI IRQs */
+ for (i=0; i < num_entries; i++){
+ printk_debug("PIR Entry %d Dev/Fn: %X Slot: %d\n", i, pirq_tbl->slots[i].devfn, pirq_tbl->slots[i].slot);
+ for (j = 0; j < 4; j++){
+ printk_debug("INT: %c bitmap: %x ", 'A'+j, pirq_tbl->slots[i].irq[j].bitmap);
+ for (k = 0; (!((pirq_tbl->slots[i].irq[j].bitmap >> k) & 1)) && (pirq_tbl->slots[i].irq[j].bitmap != 0); k++); /* finds lsb in bitmap to IRQ# */
+ pirq[j] = k;
+ printk_debug("PIRQ: %d\n", k);
+ }
+ pci_assign_irqs(pirq_tbl->slots[i].bus, pirq_tbl->slots[i].devfn, pirq); /* bus, device, slots IRQs for {A,B,C,D} */
+ }
+
+ /* put the PIR table in memory and checksum */
+ return pirtable_end;
+}
\ No newline at end of file
Modified: trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/src/mainboard/digitallogic/msm800sev/mainboard.c 2007-05-05 03:54:13 UTC (rev 2638)
@@ -6,56 +6,142 @@
#include <arch/io.h>
#include <cpu/x86/msr.h>
#include <cpu/amd/lxdef.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
#include "chip.h"
-#define DIVIL_LBAR_GPIO 0x5140000c
-static void init_gpio()
- {
+/* Print the platform configuration */
+void print_conf(void) {
+#if DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
+ int i;
+ unsigned long iol;
msr_t msr;
- printk_debug("Initializing GPIO module...\n");
- // initialize the GPIO LBAR
- msr.lo = GPIO_BASE;
- msr.hi = 0x0000f001;
- wrmsr(DIVIL_LBAR_GPIO, msr);
- msr = rdmsr(DIVIL_LBAR_GPIO);
- printk_debug("DIVIL_LBAR_GPIO set to 0x%08x 0x%08x\n", msr.hi, msr.lo);
-}
+ int cpu_msr_defs[] = { CPU_BC_L2_CONF, CPU_IM_CONFIG,
+ CPU_DM_CONFIG0, CPU_RCONF_DEFAULT,
+ CPU_RCONF_BYPASS, CPU_RCONF_A0_BF, CPU_RCONF_C0_DF, CPU_RCONF_E0_FF,
+ CPU_RCONF_SMM, CPU_RCONF_DMM, GLCP_DELAY_CONTROLS, GL_END
+ };
+ int gliu0_msr_defs[] = {MSR_GLIU0_BASE1, MSR_GLIU0_BASE2, MSR_GLIU0_BASE4, MSR_GLIU0_BASE5, MSR_GLIU0_BASE6,
+ GLIU0_P2D_BMO_0, GLIU0_P2D_BMO_1, MSR_GLIU0_SYSMEM,
+ GLIU0_P2D_RO_0, GLIU0_P2D_RO_1, GLIU0_P2D_RO_2, MSR_GLIU0_SHADOW,
+ GLIU0_IOD_BM_0, GLIU0_IOD_BM_1, GLIU0_IOD_BM_2,
+ GLIU0_IOD_SC_0, GLIU0_IOD_SC_1, GLIU0_IOD_SC_2, GLIU0_IOD_SC_3, GLIU0_IOD_SC_4, GLIU0_IOD_SC_5,
+ GLIU0_GLD_MSR_COH, GL_END
+ };
-static void init(struct device *dev)
-{
- unsigned bus = 0;
- unsigned devNic = PCI_DEVFN(0xd, 0);
- unsigned devUsb = PCI_DEVFN(0xf, 4);
- device_t usb = NULL, nic = NULL;
- unsigned char irqUsb = 0xa, irqNic = 0xb;
+ int gliu1_msr_defs[] = {MSR_GLIU1_BASE1, MSR_GLIU1_BASE2, MSR_GLIU1_BASE3, MSR_GLIU1_BASE4, MSR_GLIU1_BASE5, MSR_GLIU1_BASE6,
+ MSR_GLIU1_BASE7, MSR_GLIU1_BASE8, MSR_GLIU1_BASE9, MSR_GLIU1_BASE10,
+ GLIU1_P2D_R_0, GLIU1_P2D_R_1, GLIU1_P2D_R_2, GLIU1_P2D_R_3, MSR_GLIU1_SHADOW,
+ GLIU1_IOD_BM_0, GLIU1_IOD_BM_1, GLIU1_IOD_BM_2,
+ GLIU1_IOD_SC_0, GLIU1_IOD_SC_1, GLIU1_IOD_SC_2, GLIU1_IOD_SC_3,
+ GLIU1_GLD_MSR_COH, GL_END
+ };
- printk_debug("DIGITALLOGIC MSM800SSEV ENTER %s\n", __FUNCTION__);
+ int rconf_msr[] = { CPU_RCONF0, CPU_RCONF1, CPU_RCONF2, CPU_RCONF3, CPU_RCONF4,
+ CPU_RCONF5, CPU_RCONF6, CPU_RCONF7, GL_END
+ };
-#if 0
- // FIXME: do we need to initialize USB OHCI this way?
- printk_debug("%s (%x,%x) set USB PCI interrupt line to %d\n",
- __FUNCTION__, bus, devUsb, irqUsb);
+ int cs5536_msr[] = { MDD_LBAR_GPIO, MDD_LBAR_FLSH0, MDD_LBAR_FLSH1, MDD_LEG_IO, MDD_PIN_OPT,
+ MDD_IRQM_ZLOW, MDD_IRQM_ZHIGH, MDD_IRQM_PRIM, GL_END
+ };
- // initialize the USB controller
- usb = dev_find_slot(bus, devUsb);
- if (!usb) printk_err("Could not find USB\n");
- else pci_write_config8(usb, PCI_INTERRUPT_LINE, irqUsb);
+ int pci_msr[] = { GLPCI_CTRL, GLPCI_ARB, GLPCI_REN, GLPCI_A0_BF, GLPCI_C0_DF, GLPCI_E0_FF,
+ GLPCI_RC0, GLPCI_RC1, GLPCI_RC2, GLPCI_RC3, GLPCI_ExtMSR, GLPCI_SPARE,
+ GL_END
+ };
- printk_debug("%s (%x,%x) set NIC PCI interrupt line to %d\n",
- __FUNCTION__, bus, devNic, irqNic);
+ int dma_msr[] = { MDD_DMA_MAP, MDD_DMA_SHAD1, MDD_DMA_SHAD2, MDD_DMA_SHAD3, MDD_DMA_SHAD4,
+ MDD_DMA_SHAD5, MDD_DMA_SHAD6, MDD_DMA_SHAD7, MDD_DMA_SHAD8,
+ MDD_DMA_SHAD9, GL_END
+ };
- // initialize theEEPRO 100
- nic = dev_find_slot(bus, devNic);
- if (!nic) printk_err("Could not find USB\n");
- else pci_write_config8(nic, PCI_INTERRUPT_LINE, irqNic);
-#endif
- init_gpio();
- printk_debug("DIGITALLOGIC MSM800SSEV EXIT %s\n", __FUNCTION__);
+ printk_debug("---------- CPU ------------\n");
+
+ for(i = 0; cpu_msr_defs[i] != GL_END; i++) {
+ msr = rdmsr(cpu_msr_defs[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cpu_msr_defs[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- GLIU 0 ------------\n");
+
+ for(i = 0; gliu0_msr_defs[i] != GL_END; i++) {
+ msr = rdmsr(gliu0_msr_defs[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", gliu0_msr_defs[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- GLIU 1 ------------\n");
+
+ for(i = 0; gliu1_msr_defs[i] != GL_END; i++) {
+ msr = rdmsr(gliu1_msr_defs[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", gliu1_msr_defs[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- RCONF ------------\n");
+
+ for(i = 0; rconf_msr[i] != GL_END; i++) {
+ msr = rdmsr(rconf_msr[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", rconf_msr[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- VARIA ------------\n");
+ msr = rdmsr(0x51300010);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51300010, msr.hi, msr.lo);
+
+ msr = rdmsr(0x51400015);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", 0x51400015, msr.hi, msr.lo);
+
+ printk_debug("---------- DIVIL IRQ ------------\n");
+ msr = rdmsr(MDD_IRQM_YLOW);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YLOW, msr.hi, msr.lo);
+ msr = rdmsr(MDD_IRQM_YHIGH);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_YHIGH, msr.hi, msr.lo);
+ msr = rdmsr(MDD_IRQM_ZLOW);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZLOW, msr.hi, msr.lo);
+ msr = rdmsr(MDD_IRQM_ZHIGH);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", MDD_IRQM_ZHIGH, msr.hi, msr.lo);
+
+
+ printk_debug("---------- PCI ------------\n");
+
+ for(i = 0; pci_msr[i] != GL_END; i++) {
+ msr = rdmsr(pci_msr[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", pci_msr[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- LPC/UART DMA ------------\n");
+
+ for(i = 0; dma_msr[i] != GL_END; i++) {
+ msr = rdmsr(dma_msr[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", dma_msr[i], msr.hi, msr.lo);
+ }
+
+ printk_debug("---------- CS5536 ------------\n");
+
+ for(i = 0; cs5536_msr[i] != GL_END; i++) {
+ msr = rdmsr(cs5536_msr[i]);
+ printk_debug("MSR 0x%08X is now 0x%08X:0x%08X\n", cs5536_msr[i], msr.hi, msr.lo);
+ }
+
+ iol = inl(GPIOL_INPUT_ENABLE);
+ printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_INPUT_ENABLE, iol);
+ iol = inl(GPIOL_EVENTS_ENABLE);
+ printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_EVENTS_ENABLE, iol);
+ iol = inl(GPIOL_INPUT_INVERT_ENABLE);
+ printk_debug("IOR 0x%08X is now 0x%08X\n", GPIOL_INPUT_INVERT_ENABLE, iol);
+ iol = inl(GPIO_MAPPER_X);
+ printk_debug("IOR 0x%08X is now 0x%08X\n", GPIO_MAPPER_X, iol);
+#endif //DEFAULT_CONSOLE_LOGLEVEL >= BIOS_ERR
}
+static void init(struct device *dev) {
+
+ printk_debug("MSM800SEV ENTER %s\n", __FUNCTION__);
+
+ printk_debug("MSM800SEV EXIT %s\n", __FUNCTION__);
+}
+
static void enable_dev(struct device *dev)
{
dev->ops->init = init;
Modified: trunk/LinuxBIOSv2/targets/digitallogic/msm800sev/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/targets/digitallogic/msm800sev/Config.lb 2007-05-05 00:10:31 UTC (rev 2637)
+++ trunk/LinuxBIOSv2/targets/digitallogic/msm800sev/Config.lb 2007-05-05 03:54:13 UTC (rev 2638)
@@ -7,8 +7,9 @@
## ROM_SIZE is the total number of bytes allocated for LinuxBIOS use
## (normal AND fallback images and payloads).
-## leave 64k for vsa and 32K for video ROM
-option ROM_SIZE = 1024*1024 - 64*1024 - 32 * 1024
+## leave 36k for vsa
+##
+option ROM_SIZE = 1024*1024 - 36 * 1024
## ROM_IMAGE_SIZE is the maximum number of bytes allowed for a LinuxBIOS image,
## not including any payload.
More information about the coreboot
mailing list