[LinuxBIOS] r2632 - in trunk/LinuxBIOSv2/src: include/cpu/amd mainboard/amd/rumba mainboard/olpc/btest mainboard/olpc/rev_a northbridge/amd/gx2
svn at openbios.org
svn at openbios.org
Fri May 4 21:09:01 CEST 2007
Author: stepan
Date: 2007-05-04 21:09:01 +0200 (Fri, 04 May 2007)
New Revision: 2632
Modified:
trunk/LinuxBIOSv2/src/include/cpu/amd/gx2def.h
trunk/LinuxBIOSv2/src/mainboard/amd/rumba/Config.lb
trunk/LinuxBIOSv2/src/mainboard/olpc/btest/Config.lb
trunk/LinuxBIOSv2/src/mainboard/olpc/btest/mainboard.c
trunk/LinuxBIOSv2/src/mainboard/olpc/rev_a/Config.lb
trunk/LinuxBIOSv2/src/northbridge/amd/gx2/chipsetinit.c
trunk/LinuxBIOSv2/src/northbridge/amd/gx2/grphinit.c
trunk/LinuxBIOSv2/src/northbridge/amd/gx2/northbridge.c
Log:
This repairs the other Geode mainboards so they'll build with the new
Geode changes.
Signed-off-by: Marc Jones <marc.jones at amd.com>
Acked-by: Stefan Reinauer <stepan at coresystems.de>
Modified: trunk/LinuxBIOSv2/src/include/cpu/amd/gx2def.h
===================================================================
--- trunk/LinuxBIOSv2/src/include/cpu/amd/gx2def.h 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/include/cpu/amd/gx2def.h 2007-05-04 19:09:01 UTC (rev 2632)
@@ -90,8 +90,6 @@
#define MSR_AES ((GL1_AES << 26) + MSR_GLIU1) /* 5800xxxx */
/* South Bridge*/
#define SB_PORT 2 /* port of the SouthBridge */
-#define MSR_SB ((SB_PORT << 23) + MSR_PCI) /* 5100xxxx - address to the SouthBridge*/
-#define SB_SHIFT 20 /* 29 -> 26 -> 23 -> 20...... When making a SB address uses this shift.*/
/**/
@@ -685,182 +683,9 @@
#define POST_INTR_SEG_JUMP (0x0F0) /* vector.asm*/
-/* I don't mind if somebody decides this needs to be in a seperate file. I don't see much point
- * in it, either.
- * RGM
- */
-#define Cx5535_ID ( 0x002A100B)
-#define Cx5536_ID ( 0x208F1022)
-
-/* Cs5535 as follows. */
-/* SB_GLIU*/
-/* port0 - GLIU*/
-/* port1 - GLPCI*/
-/* port2 - USB Controller #2*/
-/* port3 - ATA-5 Controller*/
-/* port4 - MDD*/
-/* port5 - AC97*/
-/* port6 - USB Controller #1*/
-/* port7 - GLCP*/
-
-
-/* SouthBridge Equates*/
-/* MSR_SB and SB_SHIFT are located in CPU.inc*/
-#define MSR_SB_USB2_MEM_DES ((1<<16) + MSR_SB + 0x25) /* Hack to make USB P4 work */
-
-#define MSR_SB_GLIU ((9 << 14) + MSR_SB) /* 51024xxx or 510*xxxx - fake out just like GL0 on CPU. */
-#define MSR_SB_GLPCI (MSR_SB) /* 5100xxxx - don't go to the GLIU */
-#define MSR_SB_USB2 ((2 << SB_SHIFT) + MSR_SB) /* 5120xxxx */
-#define MSR_SB_ATA ((3 << SB_SHIFT) + MSR_SB) /* 5130xxxx */
-#define MSR_SB_MDD ((4 << SB_SHIFT) + MSR_SB) /* 5140xxxx, a.k.a. DIVIL = Diverse Integrated Logic device */
-#define MSR_SB_AC97 ((5 << SB_SHIFT) + MSR_SB) /* 5150xxxx */
-#define MSR_SB_USB1 ((6 << SB_SHIFT) + MSR_SB) /* 5160xxxx */
-#define MSR_SB_GLCP ((7 << SB_SHIFT) + MSR_SB) /* 5170xxxx */
-
/* */
-/* GLIU*/
+/* SB LBAR IO + MEMORY MAP*/
/* */
-#define GLIU_SB_GLD_MSR_CAP ( MSR_SB_GLIU + 0x00)
-#define GLIU_SB_GLD_MSR_CONF ( MSR_SB_GLIU + 0x01)
-#define GLIU_SB_GLD_MSR_PM ( MSR_SB_GLIU + 0x04)
-
-/* */
-/* USB1*/
-/* */
-#define USB1_SB_GLD_MSR_CAP ( MSR_SB_USB1 + 0x00)
-#define USB1_SB_GLD_MSR_CONF ( MSR_SB_USB1 + 0x01)
-#define USB1_SB_GLD_MSR_PM ( MSR_SB_USB1 + 0x04)
-/* */
-/* USB2*/
-/* */
-
-#define USB2_SB_GLD_MSR_CAP ( MSR_SB_USB2 + 0x00)
-#define USB2_SB_GLD_MSR_CONF ( MSR_SB_USB2 + 0x01)
-#define USB2_SB_GLD_MSR_PM ( MSR_SB_USB2 + 0x04)
-#define USB2_SB_GLD_MSR_OHCI_BASE ( MSR_SB_USB2 + 0x08)
-#define USB2_SB_GLD_MSR_EHCI_BASE ( MSR_SB_USB2 + 0x09)
-#define USB2_SB_GLD_MSR_DEVCTL_BASE ( MSR_SB_USB2 + 0x0A)
-#define USB2_SB_GLD_MSR_UOC_BASE ( MSR_SB_USB2 + 0x0B) /* Option controller base */
-
-/* */
-/* ATA*/
-/* */
-#define ATA_SB_GLD_MSR_CAP ( MSR_SB_ATA + 0x00)
-#define ATA_SB_GLD_MSR_CONF ( MSR_SB_ATA + 0x01)
-#define ATA_SB_GLD_MSR_ERR ( MSR_SB_ATA + 0x03)
-#define ATA_SB_GLD_MSR_PM ( MSR_SB_ATA + 0x04)
-
-/* */
-/* AC97*/
-/* */
-#define AC97_SB_GLD_MSR_CAP ( MSR_SB_AC97 + 0x00)
-#define AC97_SB_GLD_MSR_CONF ( MSR_SB_AC97 + 0x01)
-#define AC97_SB_GLD_MSR_PM ( MSR_SB_AC97 + 0x04)
-
-/* */
-/* GLPCI*/
-/* */
-#define GLPCI_SB_GLD_MSR_CAP ( MSR_SB_GLPCI + 0x00)
-#define GLPCI_SB_GLD_MSR_CONF ( MSR_SB_GLPCI + 0x01)
-#define GLPCI_SB_GLD_MSR_PM ( MSR_SB_GLPCI + 0x04)
-#define GLPCI_SB_CTRL ( MSR_SB_GLPCI + 0x10)
-#define GLPCI_CRTL_PPIDE_SET ( 1 << 17)
-/* */
-/* GLCP*/
-/* */
-#define GLCP_SB_GLD_MSR_CAP ( MSR_SB_GLCP + 0x00)
-#define GLCP_SB_GLD_MSR_CONF ( MSR_SB_GLCP + 0x01)
-#define GLCP_SB_GLD_MSR_PM ( MSR_SB_GLCP + 0x04)
-
-/* */
-/* MDD*/
-/* */
-#define MDD_SB_GLD_MSR_CAP ( MSR_SB_MDD + 0x00)
-#define MDD_SB_GLD_MSR_CONF ( MSR_SB_MDD + 0x01)
-#define MDD_SB_GLD_MSR_PM ( MSR_SB_MDD + 0x04)
-#define LBAR_EN ( 0x01)
-#define IO_MASK ( 0x1f)
-#define MEM_MASK ( 0x0FFFFF)
-#define MDD_LBAR_IRQ ( MSR_SB_MDD + 0x08)
-#define MDD_LBAR_KEL1 ( MSR_SB_MDD + 0x09)
-#define MDD_LBAR_KEL2 ( MSR_SB_MDD + 0x0A)
-#define MDD_LBAR_SMB ( MSR_SB_MDD + 0x0B)
-#define MDD_LBAR_GPIO ( MSR_SB_MDD + 0x0C)
-#define MDD_LBAR_MFGPT ( MSR_SB_MDD + 0x0D)
-#define MDD_LBAR_ACPI ( MSR_SB_MDD + 0x0E)
-#define MDD_LBAR_PMS ( MSR_SB_MDD + 0x0F)
-
-#define MDD_LBAR_FLSH0 ( MSR_SB_MDD + 0x010)
-#define MDD_LBAR_FLSH1 ( MSR_SB_MDD + 0x011)
-#define MDD_LBAR_FLSH2 ( MSR_SB_MDD + 0x012)
-#define MDD_LBAR_FLSH3 ( MSR_SB_MDD + 0x013)
-#define MDD_LEG_IO ( MSR_SB_MDD + 0x014)
-#define MDD_PIN_OPT ( MSR_SB_MDD + 0x015)
-#define MDD_SOFT_IRQ ( MSR_SB_MDD + 0x016)
-#define MDD_SOFT_RESET ( MSR_SB_MDD + 0x017)
-#define MDD_NORF_CNTRL ( MSR_SB_MDD + 0x018)
-#define MDD_NORF_T01 ( MSR_SB_MDD + 0x019)
-#define MDD_NORF_T23 ( MSR_SB_MDD + 0x01A)
-#define MDD_NANDF_DATA ( MSR_SB_MDD + 0x01B)
-#define MDD_NADF_CNTL ( MSR_SB_MDD + 0x01C)
-#define MDD_AC_DMA ( MSR_SB_MDD + 0x01E)
-#define MDD_KEL_CNTRL ( MSR_SB_MDD + 0x01F)
-
-#define MDD_IRQM_YLOW ( MSR_SB_MDD + 0x020)
-#define MDD_IRQM_YHIGH ( MSR_SB_MDD + 0x021)
-#define MDD_IRQM_ZLOW ( MSR_SB_MDD + 0x022)
-#define MDD_IRQM_ZHIGH ( MSR_SB_MDD + 0x023)
-#define MDD_IRQM_PRIM ( MSR_SB_MDD + 0x024)
-#define MDD_IRQM_LPC ( MSR_SB_MDD + 0x025)
-#define MDD_IRQM_LXIRR ( MSR_SB_MDD + 0x026)
-#define MDD_IRQM_HXIRR ( MSR_SB_MDD + 0x027)
-
-#define MDD_MFGPT_IRQ ( MSR_SB_MDD + 0x028)
-#define MDD_MFGPT_NR ( MSR_SB_MDD + 0x029)
-#define MDD_MFGPT_RES0 ( MSR_SB_MDD + 0x02A)
-#define MDD_MFGPT_RES1 ( MSR_SB_MDD + 0x02B)
-
-#define MDD_FLOP_S3F2 ( MSR_SB_MDD + 0x030)
-#define MDD_FLOP_S3F7 ( MSR_SB_MDD + 0x031)
-#define MDD_FLOP_S372 ( MSR_SB_MDD + 0x032)
-#define MDD_FLOP_S377 ( MSR_SB_MDD + 0x033)
-
-#define MDD_PIC_S ( MSR_SB_MDD + 0x034)
-#define MDD_PIT_S ( MSR_SB_MDD + 0x036)
-#define MDD_PIT_CNTRL ( MSR_SB_MDD + 0x037)
-
-#define MDD_UART1_MOD ( MSR_SB_MDD + 0x038)
-#define MDD_UART1_DON ( MSR_SB_MDD + 0x039)
-#define MDD_UART1_CONF ( MSR_SB_MDD + 0x03A)
-#define MDD_UART2_MOD ( MSR_SB_MDD + 0x03C)
-#define MDD_UART2_DON ( MSR_SB_MDD + 0x03D)
-#define MDD_UART2_CONF ( MSR_SB_MDD + 0x03E)
-
-#define MDD_DMA_MAP ( MSR_SB_MDD + 0x040)
-#define MDD_DMA_SHAD1 ( MSR_SB_MDD + 0x041)
-#define MDD_DMA_SHAD2 ( MSR_SB_MDD + 0x042)
-#define MDD_DMA_SHAD3 ( MSR_SB_MDD + 0x043)
-#define MDD_DMA_SHAD4 ( MSR_SB_MDD + 0x044)
-#define MDD_DMA_SHAD5 ( MSR_SB_MDD + 0x045)
-#define MDD_DMA_SHAD6 ( MSR_SB_MDD + 0x046)
-#define MDD_DMA_SHAD7 ( MSR_SB_MDD + 0x047)
-#define MDD_DMA_SHAD8 ( MSR_SB_MDD + 0x048)
-#define MDD_DMA_SHAD9 ( MSR_SB_MDD + 0x049)
-
-#define MDD_LPC_EADDR ( MSR_SB_MDD + 0x04C)
-#define MDD_LPC_ESTAT ( MSR_SB_MDD + 0x04D)
-#define MDD_LPC_SIRQ ( MSR_SB_MDD + 0x04E)
-#define MDD_LPC_RES ( MSR_SB_MDD + 0x04F)
-
-#define MDD_PML_TMR ( MSR_SB_MDD + 0x050)
-#define MDD_RTC_RAM_LO_CK ( MSR_SB_MDD + 0x054)
-#define MDD_RTC_DOMA_IND ( MSR_SB_MDD + 0x055)
-#define MDD_RTC_MONA_IND ( MSR_SB_MDD + 0x056)
-#define MDD_RTC_CENTURY_OFFSET ( MSR_SB_MDD + 0x057)
-
-/* */
-/* LBAR IO + MEMORY MAP*/
-/* */
#define SMBUS_BASE ( 0x6000)
#define GPIO_BASE ( 0x6100)
#define MFGPT_BASE ( 0x6200)
@@ -868,269 +693,4 @@
#define PMLogic_BASE ( 0x9D00)
-
-/* ***********************************************************/
-/* LBUS Device Equates - */
-/* ***********************************************************/
-
-/* */
-/* SMBus*/
-/* */
-
-#define SMBUS_SMBSDA ( SMBUS_BASE + 0x00)
-#define SMBUS_SMBST ( SMBUS_BASE + 0x01)
-#define SMBST_SLVSTP_SET ( 1 << 7)
-#define SMBST_SDAST_SET ( 1 << 6)
-#define SMBST_BER_SET ( 1 << 5)
-#define SMBST_NEGACK_SET ( 1 << 4)
-#define SMBST_STASTR_SET ( 1 << 3)
-#define SMBST_NMATCH_SET ( 1 << 2)
-#define SMBST_MASTER_SET ( 1 << 1)
-#define SMBST_XMIT_SET ( 1 << 0)
-#define SMBUS_SMBCST ( SMBUS_BASE + 0x02)
-#define SMBCST_TGSCL_SET ( 1 << 5)
-#define SMBCST_TSDA_SET ( 1 << 4)
-#define SMBCST_GCMTCH_SET ( 1 << 3)
-#define SMBCST_MATCH_SET ( 1 << 2)
-#define SMBCST_BB_SET ( 1 << 1)
-#define SMBCST_BUSY_SET ( 1 << 0)
-#define SMBUS_SMBCTL1 ( SMBUS_BASE + 0x03)
-#define SMBCTL1_STASTRE_SET ( 1 << 7)
-#define SMBCTL1_NMINTE_SET ( 1 << 6)
-#define SMBCTL1_GCMEN_SET ( 1 << 5)
-#define SMBCTL1_RECACK_SET ( 1 << 4)
-#define SMBCTL1_DMAEN_SET ( 1 << 3)
-#define SMBCTL1_INTEN_SET ( 1 << 2)
-#define SMBCTL1_STOP_SET ( 1 << 1)
-#define SMBCTL1_START_SET ( 1 << 0)
-#define SMBUS_SMBADDR ( SMBUS_BASE + 0x04)
-#define SMBADDR_SAEN_SET ( 1 << 7)
-#define SMBUS_SMBCTL2 ( SMBUS_BASE + 0x05)
-#define SMBCTL2_SCLFRQ_SHIFT ( 1 << 1)
-#define SMBCTL2_ENABLE_SET ( 1 << 0)
-
-/* */
-/* GPIO*/
-/* */
-
-#define GPIOL_0_SET ( 1 << 0)
-#define GPIOL_1_SET ( 1 << 1)
-#define GPIOL_2_SET ( 1 << 2)
-#define GPIOL_3_SET ( 1 << 3)
-#define GPIOL_4_SET ( 1 << 4)
-#define GPIOL_5_SET ( 1 << 5)
-#define GPIOL_6_SET ( 1 << 6)
-#define GPIOL_7_SET ( 1 << 7)
-#define GPIOL_8_SET ( 1 << 8)
-#define GPIOL_9_SET ( 1 << 9)
-#define GPIOL_10_SET ( 1 << 10)
-#define GPIOL_11_SET ( 1 << 11)
-#define GPIOL_12_SET ( 1 << 12)
-#define GPIOL_13_SET ( 1 << 13)
-#define GPIOL_14_SET ( 1 << 14)
-#define GPIOL_15_SET ( 1 << 15)
-
-#define GPIOL_0_CLEAR ( 1 << 16)
-#define GPIOL_1_CLEAR ( 1 << 17)
-#define GPIOL_2_CLEAR ( 1 << 18)
-#define GPIOL_3_CLEAR ( 1 << 19)
-#define GPIOL_4_CLEAR ( 1 << 20)
-#define GPIOL_5_CLEAR ( 1 << 21)
-#define GPIOL_6_CLEAR ( 1 << 22)
-#define GPIOL_7_CLEAR ( 1 << 23)
-#define GPIOL_8_CLEAR ( 1 << 24)
-#define GPIOL_9_CLEAR ( 1 << 25)
-#define GPIOL_10_CLEAR ( 1 << 26)
-#define GPIOL_11_CLEAR ( 1 << 27)
-#define GPIOL_12_CLEAR ( 1 << 28)
-#define GPIOL_13_CLEAR ( 1 << 29)
-#define GPIOL_14_CLEAR ( 1 << 30)
-#define GPIOL_15_CLEAR ( 1 << 31)
-
-#define GPIOH_16_SET ( 1 << 0)
-#define GPIOH_17_SET ( 1 << 1)
-#define GPIOH_18_SET ( 1 << 2)
-#define GPIOH_19_SET ( 1 << 3)
-#define GPIOH_20_SET ( 1 << 4)
-#define GPIOH_21_SET ( 1 << 5)
-#define GPIOH_22_SET ( 1 << 6)
-#define GPIOH_23_SET ( 1 << 7)
-#define GPIOH_24_SET ( 1 << 8)
-#define GPIOH_25_SET ( 1 << 9)
-#define GPIOH_26_SET ( 1 << 10)
-#define GPIOH_27_SET ( 1 << 11)
-#define GPIOH_28_SET ( 1 << 12)
-#define GPIOH_29_SET ( 1 << 13)
-#define GPIOH_30_SET ( 1 << 14)
-#define GPIOH_31_SET ( 1 << 15)
-
-#define GPIOH_16_CLEAR ( 1 << 16)
-#define GPIOH_17_CLEAR ( 1 << 17)
-#define GPIOH_18_CLEAR ( 1 << 18)
-#define GPIOH_19_CLEAR ( 1 << 19)
-#define GPIOH_20_CLEAR ( 1 << 20)
-#define GPIOH_21_CLEAR ( 1 << 21)
-#define GPIOH_22_CLEAR ( 1 << 22)
-#define GPIOH_23_CLEAR ( 1 << 23)
-#define GPIOH_24_CLEAR ( 1 << 24)
-#define GPIOH_25_CLEAR ( 1 << 25)
-#define GPIOH_26_CLEAR ( 1 << 26)
-#define GPIOH_27_CLEAR ( 1 << 27)
-#define GPIOH_28_CLEAR ( 1 << 28)
-#define GPIOH_29_CLEAR ( 1 << 29)
-#define GPIOH_30_CLEAR ( 1 << 30)
-#define GPIOH_31_CLEAR ( 1 << 31)
-
-
-/* GPIO LOW Bank Bit Registers*/
-#define GPIOL_OUTPUT_VALUE ( GPIO_BASE + 0x00)
-#define GPIOL_OUTPUT_ENABLE ( GPIO_BASE + 0x04)
-#define GPIOL_OUT_OPENDRAIN ( GPIO_BASE + 0x08)
-#define GPIOL_OUTPUT_INVERT_ENABLE ( GPIO_BASE + 0x0C)
-#define GPIOL_OUT_AUX1_SELECT ( GPIO_BASE + 0x10)
-#define GPIOL_OUT_AUX2_SELECT ( GPIO_BASE + 0x14)
-#define GPIOL_PULLUP_ENABLE ( GPIO_BASE + 0x18)
-#define GPIOL_PULLDOWN_ENABLE ( GPIO_BASE + 0x1C)
-#define GPIOL_INPUT_ENABLE ( GPIO_BASE + 0x20)
-#define GPIOL_INPUT_INVERT_ENABLE ( GPIO_BASE + 0x24)
-#define GPIOL_IN_FILTER_ENABLE ( GPIO_BASE + 0x28)
-#define GPIOL_IN_EVENTCOUNT_ENABLE ( GPIO_BASE + 0x2C)
-#define GPIOL_READ_BACK ( GPIO_BASE + 0x30)
-#define GPIOL_IN_AUX1_SELECT ( GPIO_BASE + 0x34)
-#define GPIOL_EVENTS_ENABLE ( GPIO_BASE + 0x38)
-#define GPIOL_LOCK_ENABLE ( GPIO_BASE + 0x3C)
-#define GPIOL_IN_POSEDGE_ENABLE ( GPIO_BASE + 0x40)
-#define GPIOL_IN_NEGEDGE_ENABLE ( GPIO_BASE + 0x44)
-#define GPIOL_IN_POSEDGE_STATUS ( GPIO_BASE + 0x48)
-#define GPIOL_IN_NEGEDGE_STATUS ( GPIO_BASE + 0x4C)
-
-/* GPIO High Bank Bit Registers*/
-#define GPIOH_OUTPUT_VALUE ( GPIO_BASE + 0x80)
-#define GPIOH_OUTPUT_ENABLE ( GPIO_BASE + 0x84)
-#define GPIOH_OUT_OPENDRAIN ( GPIO_BASE + 0x88)
-#define GPIOH_OUTPUT_INVERT_ENABLE ( GPIO_BASE + 0x8C)
-#define GPIOH_OUT_AUX1_SELECT ( GPIO_BASE + 0x90)
-#define GPIOH_OUT_AUX2_SELECT ( GPIO_BASE + 0x94)
-#define GPIOH_PULLUP_ENABLE ( GPIO_BASE + 0x98)
-#define GPIOH_PULLDOWN_ENABLE ( GPIO_BASE + 0x9C)
-#define GPIOH_INPUT_ENABLE ( GPIO_BASE + 0x0A0)
-#define GPIOH_INPUT_INVERT_ENABLE ( GPIO_BASE + 0x0A4)
-#define GPIOH_IN_FILTER_ENABLE ( GPIO_BASE + 0x0A8)
-#define GPIOH_IN_EVENTCOUNT_ENABLE ( GPIO_BASE + 0x0AC)
-#define GPIOH_READ_BACK ( GPIO_BASE + 0x0B0)
-#define GPIOH_IN_AUX1_SELECT ( GPIO_BASE + 0x0B4)
-#define GPIOH_EVENTS_ENABLE ( GPIO_BASE + 0x0B8)
-#define GPIOH_LOCK_ENABLE ( GPIO_BASE + 0x0BC)
-#define GPIOH_IN_POSEDGE_ENABLE ( GPIO_BASE + 0x0C0)
-#define GPIOH_IN_NEGEDGE_ENABLE ( GPIO_BASE + 0x0C4)
-#define GPIOH_IN_POSEDGE_STATUS ( GPIO_BASE + 0x0C8)
-#define GPIOH_IN_NEGEDGE_STATUS ( GPIO_BASE + 0x0CC)
-
-/* Input Conditioning Function Registers*/
-#define GPIO_00_FILTER_AMOUNT ( GPIO_BASE + 0x50)
-#define GPIO_00_FILTER_COUNT ( GPIO_BASE + 0x52)
-#define GPIO_00_EVENT_COUNT ( GPIO_BASE + 0x54)
-#define GPIO_00_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x56)
-#define GPIO_01_FILTER_AMOUNT ( GPIO_BASE + 0x58)
-#define GPIO_01_FILTER_COUNT ( GPIO_BASE + 0x5A)
-#define GPIO_01_EVENT_COUNT ( GPIO_BASE + 0x5C)
-#define GPIO_01_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x5E)
-#define GPIO_02_FILTER_AMOUNT ( GPIO_BASE + 0x60)
-#define GPIO_02_FILTER_COUNT ( GPIO_BASE + 0x62)
-#define GPIO_02_EVENT_COUNT ( GPIO_BASE + 0x64)
-#define GPIO_02_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x66)
-#define GPIO_03_FILTER_AMOUNT ( GPIO_BASE + 0x68)
-#define GPIO_03_FILTER_COUNT ( GPIO_BASE + 0x6A)
-#define GPIO_03_EVENT_COUNT ( GPIO_BASE + 0x6C)
-#define GPIO_03_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x6E)
-#define GPIO_04_FILTER_AMOUNT ( GPIO_BASE + 0x70)
-#define GPIO_04_FILTER_COUNT ( GPIO_BASE + 0x72)
-#define GPIO_04_EVENT_COUNT ( GPIO_BASE + 0x74)
-#define GPIO_04_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x76)
-#define GPIO_05_FILTER_AMOUNT ( GPIO_BASE + 0x78)
-#define GPIO_05_FILTER_COUNT ( GPIO_BASE + 0x7A)
-#define GPIO_05_EVENT_COUNT ( GPIO_BASE + 0x7C)
-#define GPIO_05_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x7E)
-#define GPIO_06_FILTER_AMOUNT ( GPIO_BASE + 0x0D0)
-#define GPIO_06_FILTER_COUNT ( GPIO_BASE + 0x0D2)
-#define GPIO_06_EVENT_COUNT ( GPIO_BASE + 0x0D4)
-#define GPIO_06_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x0D6)
-#define GPIO_07_FILTER_AMOUNT ( GPIO_BASE + 0x0D8)
-#define GPIO_07_FILTER_COUNT ( GPIO_BASE + 0x0DA)
-#define GPIO_07_EVENT_COUNT ( GPIO_BASE + 0x0DC)
-#define GPIO_07_EVENTCOMPARE_VALUE ( GPIO_BASE + 0x0DE)
-
-/* R/W GPIO Interrupt &PME Mapper Registers*/
-#define GPIO_MAPPER_X ( GPIO_BASE + 0x0E0)
-#define GPIO_MAPPER_Y ( GPIO_BASE + 0x0E4)
-#define GPIO_MAPPER_Z ( GPIO_BASE + 0x0E8)
-#define GPIO_MAPPER_W ( GPIO_BASE + 0x0EC)
-#define GPIO_FE_SELECT_0 ( GPIO_BASE + 0x0F0)
-#define GPIO_FE_SELECT_1 ( GPIO_BASE + 0x0F1)
-#define GPIO_FE_SELECT_2 ( GPIO_BASE + 0x0F2)
-#define GPIO_FE_SELECT_3 ( GPIO_BASE + 0x0F3)
-#define GPIO_FE_SELECT_4 ( GPIO_BASE + 0x0F4)
-#define GPIO_FE_SELECT_5 ( GPIO_BASE + 0x0F5)
-#define GPIO_FE_SELECT_6 ( GPIO_BASE + 0x0F6)
-#define GPIO_FE_SELECT_7 ( GPIO_BASE + 0x0F7)
-
-/* Event Counter Decrement Registers*/
-#define GPIOL_IN_EVENT_DECREMENT ( GPIO_BASE + 0x0F8)
-#define GPIOH_IN_EVENT_DECREMENT ( GPIO_BASE + 0x0FC)
-
-/* This is for 286reset compatibility. 0xCange to mat0xc 5535 virtualized stuff.*/
-#define FUNC0 ( 0x90)
-
-
-/* sworley, PMC register*/
-#define PM_SSD ( PMLogic_BASE + 0x00)
-#define PM_SCXA ( PMLogic_BASE + 0x04)
-#define PM_SCYA ( PMLogic_BASE + 0x08)
-#define PM_SODA ( PMLogic_BASE + 0x0C)
-#define PM_SCLK ( PMLogic_BASE + 0x10)
-#define PM_SED ( PMLogic_BASE + 0x14)
-#define PM_SCXD ( PMLogic_BASE + 0x18)
-#define PM_SCYD ( PMLogic_BASE + 0x1C)
-#define PM_SIDD ( PMLogic_BASE + 0x20)
-#define PM_WKD ( PMLogic_BASE + 0x30)
-#define PM_WKXD ( PMLogic_BASE + 0x34)
-#define PM_RD ( PMLogic_BASE + 0x38)
-#define PM_WKXA ( PMLogic_BASE + 0x3C)
-#define PM_FSD ( PMLogic_BASE + 0x40)
-#define PM_TSD ( PMLogic_BASE + 0x44)
-#define PM_PSD ( PMLogic_BASE + 0x48)
-#define PM_NWKD ( PMLogic_BASE + 0x4C)
-#define PM_AWKD ( PMLogic_BASE + 0x50)
-#define PM_SSC ( PMLogic_BASE + 0x54)
-
-
-/* FLASH device macros */
-#define FLASH_TYPE_NONE 0 /* No flash device installed */
-#define FLASH_TYPE_NAND 1 /* NAND device */
-#define FLASH_TYPE_NOR 2 /* NOR device */
-
-#define FLASH_IF_MEM 1 /* Memory or memory-mapped I/O interface for Flash device */
-#define FLASH_IF_IO 2 /* I/O interface for Flash device */
-
-/* Flash Memory Mask values */
-#define FLASH_MEM_DEFAULT 0x00000000
-#define FLASH_MEM_4K 0xFFFFF000
-#define FLASH_MEM_8K 0xFFFFE000
-#define FLASH_MEM_16K 0xFFFFC000
-#define FLASH_MEM_128K 0xFFFE0000
-#define FLASH_MEM_512K 0xFFFC0000
-#define FLASH_MEM_4M 0xFFC00000
-#define FLASH_MEM_8M 0xFF800000
-#define FLASH_MEM_16M 0xFF000000
-
-/* Flash IO Mask values */
-#define FLASH_IO_DEFAULT 0x00000000
-#define FLASH_IO_16B 0x0000FFF0
-#define FLASH_IO_32B 0x0000FFE0
-#define FLASH_IO_64B 0x0000FFC0
-#define FLASH_IO_128B 0x0000FF80
-#define FLASH_IO_256B 0x0000FF00
-
-
-
#endif /* CPU_AMD_GX2DEF_H */
Modified: trunk/LinuxBIOSv2/src/mainboard/amd/rumba/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/amd/rumba/Config.lb 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/mainboard/amd/rumba/Config.lb 2007-05-04 19:09:01 UTC (rev 2632)
@@ -134,8 +134,6 @@
device pci 1.1 on end
chip southbridge/amd/cs5536
register "lpc_serirq_enable" = "0x80" # enabled with default timing
- register "lpc_irq" = "((1<<3)|(1<<4))" # IRQ 3 & 4
- register "enable_gpio0_inta" = "1"
device pci d.0 on end # Realtek 8139 LAN
device pci f.0 on end # ISA Bridge
device pci f.2 on end # IDE Controller
Modified: trunk/LinuxBIOSv2/src/mainboard/olpc/btest/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/olpc/btest/Config.lb 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/mainboard/olpc/btest/Config.lb 2007-05-04 19:09:01 UTC (rev 2632)
@@ -144,17 +144,17 @@
# Active(Quiet) mode. Save power....
# SIRQ Enable = Enabled
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
- register "lpc_irq" = "0x00001002"
- register "lpc_serirq_enable" = "0xEFFD0080"
- register "enable_gpio0_inta" = "1"
- register "enable_ide_nand_flash" = "1"
- register "enable_uarta" = "1"
- register "enable_USBP4_host" = "1"
- register "audio_irq" = "5"
- register "usbf4_irq" = "10"
- register "usbf5_irq" = "10"
- register "usbf6_irq" = "0"
- register "usbf7_irq" = "0"
+ #register "lpc_irq" = "0x00001002"
+ #register "lpc_serirq_enable" = "0xEFFD0080"
+ #register "enable_gpio0_inta" = "1"
+ #register "enable_ide_nand_flash" = "1"
+ #register "enable_uarta" = "1"
+ #register "enable_USBP4_host" = "1"
+ #register "audio_irq" = "5"
+ #register "usbf4_irq" = "10"
+ #register "usbf5_irq" = "10"
+ #register "usbf6_irq" = "0"
+ #register "usbf7_irq" = "0"
device pci d.0 on end # Realtek 8139 LAN
device pci f.0 on end # ISA Bridge
device pci f.2 on end # IDE Controller
Modified: trunk/LinuxBIOSv2/src/mainboard/olpc/btest/mainboard.c
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/olpc/btest/mainboard.c 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/mainboard/olpc/btest/mainboard.c 2007-05-04 19:09:01 UTC (rev 2632)
@@ -7,6 +7,7 @@
#include <pc80/mc146818rtc.h>
#include "chip.h"
#include "../southbridge/amd/cs5536/cs5536_smbus2.h"
+#include <cpu/amd/vr.h>
/* Borrowed from mc146818rtc.c */
Modified: trunk/LinuxBIOSv2/src/mainboard/olpc/rev_a/Config.lb
===================================================================
--- trunk/LinuxBIOSv2/src/mainboard/olpc/rev_a/Config.lb 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/mainboard/olpc/rev_a/Config.lb 2007-05-04 19:09:01 UTC (rev 2632)
@@ -144,17 +144,17 @@
# Active(Quiet) mode. Save power....
# SIRQ Enable = Enabled
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
- register "lpc_irq" = "0x00001002"
- register "lpc_serirq_enable" = "0xEFFD0080"
- register "enable_gpio0_inta" = "1"
- register "enable_ide_nand_flash" = "1"
- register "enable_uarta" = "1"
- register "enable_USBP4_host" = "1"
- register "audio_irq" = "5"
- register "usbf4_irq" = "10"
- register "usbf5_irq" = "10"
- register "usbf6_irq" = "0"
- register "usbf7_irq" = "0"
+ #register "lpc_irq" = "0x00001002"
+ #register "lpc_serirq_enable" = "0xEFFD0080"
+ #register "enable_gpio0_inta" = "1"
+ #register "enable_ide_nand_flash" = "1"
+ #register "enable_uarta" = "1"
+ #register "enable_USBP4_host" = "1"
+ #register "audio_irq" = "5"
+ #register "usbf4_irq" = "10"
+ #register "usbf5_irq" = "10"
+ #register "usbf6_irq" = "0"
+ #register "usbf7_irq" = "0"
device pci d.0 on end # Realtek 8139 LAN
device pci f.0 on end # ISA Bridge
device pci f.2 on end # IDE Controller
Modified: trunk/LinuxBIOSv2/src/northbridge/amd/gx2/chipsetinit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/gx2/chipsetinit.c 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/gx2/chipsetinit.c 2007-05-04 19:09:01 UTC (rev 2632)
@@ -12,6 +12,7 @@
#include <cpu/amd/gx2def.h>
#include <cpu/x86/msr.h>
#include <cpu/x86/cache.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
/* the structs in this file only set msr.lo. But ... that may not always be true */
Modified: trunk/LinuxBIOSv2/src/northbridge/amd/gx2/grphinit.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/gx2/grphinit.c 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/gx2/grphinit.c 2007-05-04 19:09:01 UTC (rev 2632)
@@ -4,31 +4,8 @@
#define VIDEO_MB 8 // MB of video memory
-/*
- * Write to a Virtual Register
- * AX = Class/Index
- * CX = data to write
- */
-void vrWrite(uint16_t wClassIndex, uint16_t wData)
-{
- outl(((uint32_t) VR_UNLOCK << 16) | wClassIndex, VRC_INDEX);
- outw(wData, VRC_DATA);
-}
/*
- * Read from a Virtual Register
- * AX = Class/Index
- * Returns a 16-bit word of data
- */
-uint16_t vrRead(uint16_t wClassIndex)
-{
- uint16_t wData;
- outl(((uint32_t) VR_UNLOCK << 16) | wClassIndex, VRC_INDEX);
- wData = inw(VRC_DATA);
- return wData;
-}
-
-/*
* This function mirrors the Graphics_Init routine in GeodeROM.
*/
void graphics_init(void)
Modified: trunk/LinuxBIOSv2/src/northbridge/amd/gx2/northbridge.c
===================================================================
--- trunk/LinuxBIOSv2/src/northbridge/amd/gx2/northbridge.c 2007-05-04 19:05:36 UTC (rev 2631)
+++ trunk/LinuxBIOSv2/src/northbridge/amd/gx2/northbridge.c 2007-05-04 19:09:01 UTC (rev 2632)
@@ -13,6 +13,7 @@
#include <cpu/x86/msr.h>
#include <cpu/x86/cache.h>
#include <cpu/amd/vr.h>
+#include "../../../southbridge/amd/cs5536/cs5536.h"
#define VIDEO_MB 8
extern void graphics_init(void);
More information about the coreboot
mailing list