[LinuxBIOS] trying to boot gigabyte m57sli-s4
Ward Vandewege
ward at gnu.org
Mon Mar 12 22:54:34 CET 2007
Hi Yinghai,
It works! Seems like your kernel options make all the difference.
The machine boots with these extra parameters:
apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq
snd-hda-intel.enable_msi=1
This works in 2.6.20.1 and 2.6.21-rc3.
There's one problem: the intergrated network controller does not work.
Here's a snippet from a boot with the proprietary bios:
[ 29.675453] forcedeth.c: Reverse Engineered nForce ethernet driver.
Version 0.60.
[ 29.683267] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 5
[ 29.688967] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LMAC] -> GSI 5
(level, low) -> IRQ 5
[ 29.697623] forcedeth: using HIGHDMA
[ 30.224777] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:08.0
[ 30.231693] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 30.238082] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
Here's the equivalent booting with LinuxBIOS:
[ 66.416122] forcedeth.c: Reverse Engineered nForce ethernet driver.
Version 0.60.
[ 66.423682] forcedeth: using HIGHDMA
[ 66.948233] eth0: forcedeth.c: subsystem: 01022:2b80 bound to 0000:00:08.0
[ 66.955144] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 66.961528] ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
Booted under LinuxBIOS, there is simply no network device available. Ideas to
get the nic to work?
Also, the LinuxBIOS code does not support ACPI; would it be hard to add that?
That's quite important in this case - it's a desktop board.
I've attached the boot log with LinuxBIOS
(minicom-gb-20070312-03-lb-2.6.21-rc3-64.cap) and a boot with a proprietary
BIOS (minicom-gb-20070312-04-prop-2.6.21-rc3-64.cap).
Thanks,
Ward.
--
Ward Vandewege <ward at fsf.org>
Free Software Foundation - Senior System Administrator
-------------- next part --------------
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
LinuxBIOS-1.1.8_m57sli_Fallback Thu Mar 8 11:42:29 EST 2007 starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started:
started ap apicid: 01
SBLink=00
NC node|link=00
begin msr fid, vid 310a12120a0c0202
end msr fid, vid 310a120a0a0c020c
mcp55_num:01
ht reset -
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 5
n_ports: 10
ehci reset done
ehci started
No device found in debug port 5
debug_port: 6
n_ports: 10
ehci reset done
ehci started
No device found in debug port 6
debug_port: 7
n_ports: 10
ehci reset done
ehci started
No device found in debug port 7
debug_port: 8
n_ports: 10
ehci reset done
ehci started
No device found in debug port 8
debug_port: 9
n_ports: 10
ehci reset done
ehci started
No device found in debug port 9
debug_port: 10
n_ports: 10
ehci reset done
ehci started
No device found in debug port 10
debug_port: 1
n_ports: 10
ehci reset done
ehci started
No device found in debug port 1
debug_port: 2
n_ports: 10
ehci reset done
ehci started
No device found in debug port 2
debug_port: 3
n_ports: 10
ehci reset done
ehci started
No device found in debug port 3
debug_port: 4
n_ports: 10
ehci reset done
ehci started
No device found in debug port 4
LinuxBIOS-1.1.8_m57sli_Fallback Thu Mar 8 11:42:29 EST 2007 starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started:
started ap apicid: 01
SBLink=00
NC node|link=00
begin msr fid, vid 310a120a0a0c020c
end msr fid, vid 310a120a0a0c020c
mcp55_num:01
Ram1.00
Ram2.00
Unbuffered
400Mhz
Interleaved
RAM: 0x00200000 KB
Ram3
dimm_mask = 00000011
x4_mask = 00000000
x16_mask = 00000000
single_rank_mask = 00000000
ODC = 00113222
Addr Timing= 00202520
Initializing memory: done
Setting variable MTRR 2, base: 0MB, range: 2048MB, type WB
set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=1a done
set DQS timing:DQSPos: 00 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=2c done
Total DQS Training : tsc [00]=00000007e45f4e76
Total DQS Training : tsc [01]=00000007e5b5999c
Total DQS Training : tsc [02]=0000000851be99cc
Total DQS Training : tsc [03]=0000000852e3160c
Ram4
v_esp=000ceec4
Copying data from cache to ram -- switching to use ram as stack... Done
Disabling cache as ram now
Clearing initial memory region: Done
Copying LinuxBIOS to ram.
src=fffdf000
dst=00100000
linxbios_ram.nrv2b length = 0000d318
linxbios_ram.bin length = 000212b0
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8_m57sli_Fallback Thu Mar 8 11:42:29 EST 2007 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:01.0 [10de/0360] enabled
PCI: 00:01.1 [10de/0368] enabled
PCI: 00:01.2 [10de/036a] enabled
PCI: 00:01.3 [10de/036b] enabled
PCI: 00:02.0 [10de/036c] enabled
PCI: 00:02.1 [10de/036d] enabled
PCI: 00:04.0 [10de/036e] enabled
PCI: 00:05.0 [10de/037f] enabled
PCI: 00:05.1 [10de/037f] enabled
PCI: 00:05.2 [10de/037f] enabled
PCI: 00:06.0 [10de/0370] enabled
PCI: 00:06.1 [10de/0371] enabled
PCI: 00:08.0 [10de/0373] enabled
PCI: 00:0a.0 [10de/0376] enabled
PCI: 00:0b.0 [10de/0374] enabled
PCI: 00:0c.0 [10de/0374] enabled
PCI: 00:0d.0 [10de/0378] enabled
PCI: 00:0e.0 [10de/0375] enabled
PCI: 00:0f.0 [10de/0377] enabled
PNP: 002e.0 disabled
PNP: 002e.1 enabled
PNP: 002e.2 disabled
PNP: 002e.3 disabled
PNP: 002e.4 disabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled
smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
PCI: pci_scan_bus for bus 02
PCI: 02:00.0 [10de/0392] enabled
PCI: pci_scan_bus returning with max=002
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
PCI: pci_scan_bus for bus 04
PCI: pci_scan_bus returning with max=004
PCI: pci_scan_bus for bus 05
PCI: pci_scan_bus returning with max=005
PCI: pci_scan_bus for bus 06
PCI: pci_scan_bus returning with max=006
PCI: pci_scan_bus for bus 07
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
done
Allocating resources...
Reading resources...
PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io
PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem
PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem
PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io
PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem
PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem
PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io
PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem
PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem
PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io
PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem
PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem
PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io
PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem
PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem
PCI: 00:0f.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 07 io
PCI: 00:0f.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 07 prefmem
PCI: 00:0f.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 07 mem
Done reading resources.
Allocating VGA resource PCI: 02:00.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0a.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000
Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
Setting resources...
VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device
PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] io <node 0 link 0>
PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] prefmem <node 0 link 0>
PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f61fffff] mem <node 0 link 0>
PCI: 00:01.0 14 <- [0x00f6144000 - 0x00f6144fff] mem
PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq
PCI: 00:01.1 10 <- [0x0000002c00 - 0x0000002c3f] io
PCI: 00:01.1 20 <- [0x0000002c40 - 0x0000002c7f] io
PCI: 00:01.1 24 <- [0x0000002c80 - 0x0000002cbf] io
PCI: 00:01.1 60 <- [0x0000002000 - 0x00000020ff] io
PCI: 00:01.1 64 <- [0x0000002400 - 0x00000024ff] io
PCI: 00:01.1 68 <- [0x0000002800 - 0x00000028ff] io
PCI: 00:01.3 10 <- [0x00f6100000 - 0x00f613ffff] mem
PCI: 00:02.0 10 <- [0x00f6145000 - 0x00f6145fff] mem
PCI: 00:02.1 10 <- [0x00f614a000 - 0x00f614a0ff] mem
PCI: 00:02.1 10 <- [0x00f614a000 - 0x00f614a0ff] mem
PCI: 00:04.0 20 <- [0x0000002cc0 - 0x0000002ccf] io
PCI: 00:05.0 10 <- [0x0000003000 - 0x0000003007] io
PCI: 00:05.0 14 <- [0x0000003070 - 0x0000003073] io
PCI: 00:05.0 18 <- [0x0000003010 - 0x0000003017] io
PCI: 00:05.0 1c <- [0x0000003080 - 0x0000003083] io
PCI: 00:05.0 20 <- [0x0000002cd0 - 0x0000002cdf] io
PCI: 00:05.0 24 <- [0x00f6146000 - 0x00f6146fff] mem
PCI: 00:05.1 10 <- [0x0000003020 - 0x0000003027] io
PCI: 00:05.1 14 <- [0x0000003090 - 0x0000003093] io
PCI: 00:05.1 18 <- [0x0000003030 - 0x0000003037] io
PCI: 00:05.1 1c <- [0x00000030a0 - 0x00000030a3] io
PCI: 00:05.1 20 <- [0x0000002ce0 - 0x0000002cef] io
PCI: 00:05.1 24 <- [0x00f6147000 - 0x00f6147fff] mem
PCI: 00:05.2 10 <- [0x0000003040 - 0x0000003047] io
PCI: 00:05.2 14 <- [0x00000030b0 - 0x00000030b3] io
PCI: 00:05.2 18 <- [0x0000003050 - 0x0000003057] io
PCI: 00:05.2 1c <- [0x00000030c0 - 0x00000030c3] io
PCI: 00:05.2 20 <- [0x0000002cf0 - 0x0000002cff] io
PCI: 00:05.2 24 <- [0x00f6148000 - 0x00f6148fff] mem
PCI: 00:06.1 10 <- [0x00f6140000 - 0x00f6143fff] mem
PCI: 00:08.0 10 <- [0x00f6149000 - 0x00f6149fff] mem
PCI: 00:08.0 14 <- [0x0000003060 - 0x0000003067] io
PCI: 00:08.0 18 <- [0x00f614b000 - 0x00f614b0ff] mem
PCI: 00:08.0 1c <- [0x00f614c000 - 0x00f614c00f] mem
PCI: 00:0a.0 1c <- [0x0000001000 - 0x0000001fff] bus 02 io
PCI: 00:0a.0 24 <- [0x00e0000000 - 0x00efffffff] bus 02 prefmem
PCI: 00:0a.0 20 <- [0x00f4000000 - 0x00f60fffff] bus 02 mem
PCI: 02:00.0 10 <- [0x00f4000000 - 0x00f4ffffff] mem
PCI: 02:00.0 14 <- [0x00e0000000 - 0x00efffffff] prefmem64
PCI: 02:00.0 1c <- [0x00f5000000 - 0x00f5ffffff] mem64
PCI: 02:00.0 24 <- [0x0000001000 - 0x000000107f] io
PCI: 02:00.0 30 <- [0x00f6000000 - 0x00f601ffff] romem
PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 140
PCI: 00:00.0 subsystem <- 1022/2b80
PCI: 00:00.0 cmd <- 146
PCI: 00:01.0 subsystem <- 1022/2b80
PCI: 00:01.0 cmd <- 14f
mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff
mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060
mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064
PCI: 00:01.1 subsystem <- 1022/2b80
PCI: 00:01.1 cmd <- 141
PCI: 00:01.2 cmd <- 540
PCI: 00:01.3 cmd <- 142
PCI: 00:02.0 subsystem <- 1022/2b80
PCI: 00:02.0 cmd <- 142
PCI: 00:02.1 subsystem <- 1022/2b80
PCI: 00:02.1 cmd <- 142
PCI: 00:04.0 subsystem <- 1022/2b80
PCI: 00:04.0 cmd <- 141
PCI: 00:05.0 subsystem <- 1022/2b80
PCI: 00:05.0 cmd <- 143
PCI: 00:05.1 subsystem <- 1022/2b80
PCI: 00:05.1 cmd <- 143
PCI: 00:05.2 subsystem <- 1022/2b80
PCI: 00:05.2 cmd <- 143
PCI: 00:06.0 bridge ctrl <- 0a03
PCI: 00:06.0 cmd <- 144
PCI: 00:06.1 subsystem <- 1022/2b80
PCI: 00:06.1 cmd <- 142
PCI: 00:08.0 subsystem <- 1022/2b80
PCI: 00:08.0 cmd <- 143
PCI: 00:0a.0 bridge ctrl <- 000b
PCI: 00:0a.0 cmd <- 147
PCI: 02:00.0 cmd <- 143
PCI: 00:0b.0 bridge ctrl <- 0003
PCI: 00:0b.0 cmd <- 140
PCI: 00:0c.0 bridge ctrl <- 0003
PCI: 00:0c.0 cmd <- 140
PCI: 00:0d.0 bridge ctrl <- 0003
PCI: 00:0d.0 cmd <- 140
PCI: 00:0e.0 bridge ctrl <- 0003
PCI: 00:0e.0 cmd <- 140
PCI: 00:0f.0 bridge ctrl <- 0003
PCI: 00:0f.0 cmd <- 140
PCI: 00:18.1 subsystem <- 1022/2b80
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 1022/2b80
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
start_eip=0x00005000, offset=0x00110000, code_size=0x0000005b
Final : tsc [0a]=00000008c92e2df6
Initializing CPU #0
CPU: vendor AMD device 40fb2
CPU: family 0f, model 4b, stepping 02
brandId=08cd
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
Setting up local apic... apic_id: 0x00 done.
ECC Disabled
CPU #0 Initialized
Initializing CPU #1
Waiting for 1 CPUS to stop
CPU: vendor AMD device 40fb2
CPU: family 0f, model 4b, stepping 02
brandId=08cd
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 2048MB, type WB
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
Setting up local apic... apic_id: 0x01 done.
CPU #1 Initialized
All AP CPUs stopped
Final : tsc [0b]=00000008d92328a9
PCI: 00:18.0 init
PCI: 00:01.0 init
set power on after power fail
RTC Init
RTC: Checksum invalid zeroing cmos
Invalid CMOS LB checksum
PNP: 002e.1 init
PNP: 002e.5 init
PNP: 002e.6 init
PCI: 00:01.1 init
PCI: 00:02.1 init
PCI: 00:04.0 init
IDE0
PCI: 00:05.0 init
SATA S SATA P
PCI: 00:05.1 init
SATA S SATA P
PCI: 00:05.2 init
SATA S SATA P
PCI: 00:06.0 init
dev_root mem base = 0x00e0000000
[0x50] <-- 0xe0000000
PCI: 00:06.1 init
base = f6140000
codec_mask = 01
codec viddid: 10ec0883
No verb!
PCI: 00:08.0 init
MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1
PCI: 00:0a.0 init
PCI: 00:0b.0 init
PCI: 00:0c.0 init
PCI: 00:0d.0 init
PCI: 00:0e.0 init
PCI: 00:0f.0 init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 00:01.2 init
PCI: 00:01.3 init
PCI: 02:00.0 init
rom address for PCI: 02:00.0 = f6000000
copying VGA ROM Image from f6000000 to c0000, ee00 bytes
entering emulator
halt_sys: file /home/ward/lb/yh/freebios2/src/devices/emulator/x86emu/ops.c, line 4387
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 00000274
Adjust low_table_end from 0x00000500 to 0x00001000
Adjust rom_table_end from 0x000f0400 to 0x00100000
Wrote linuxbios table at: 00000500 - 00000db0 checksum bfd7
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfffc0000 - 0xfffdefff
Found ELF candiate at offset 0
New segment addr 0x100000 size 0x3ff20 offset 0xc0 filesize 0x16168
(cleaned up) New segment addr 0x100000 size 0x3ff20 offset 0xc0 filesize 0x16168
New segment addr 0x13ff20 size 0x48 offset 0x16240 filesize 0x48
(cleaned up) New segment addr 0x13ff20 size 0x48 offset 0x16240 filesize 0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x000000007ff84000 memsz: 0x000000000003e000 filesz: 0x0000000000016168
Clearing Segment: addr: 0x000000007ff9a168 memsz: 0x0000000000027e98
Loading Segment: addr: 0x000000000013ff20 memsz: 0x0000000000000048 filesz: 0x0000000000000048
Loading Segment: addr: 0x000000000013e000 memsz: 0x0000000000001f20 filesz: 0x0000000000000000
Clearing Segment: addr: 0x000000000013e000 memsz: 0x0000000000001f20
Jumping to boot code at 0x10f768
FILO version 0.5 (ward at neuromancer) Tue Mar 6 14:58:22 EST 2007
collect_sys_info: boot eax = 0xe1fb007
collect_sys_info: boot ebx = 0x7ffe2180
collect_sys_info: boot arg = 0x7ffe2180
malloc_diag: alloc: 0 bytes (0 blocks), free: 16376 bytes (1 blocks)
malloc_diag: alloc: 24 bytes (1 blocks), free: 16352 bytes (1 blocks)
collect_elfboot_info: Bootloader: elfboot
collect_elfboot_info: Version: 1.3
malloc_diag: alloc: 40 bytes (2 blocks), free: 16336 bytes (1 blocks)
collect_linuxbios_info: Searching for LinuxBIOS tables...
find_lb_table: Found canidate at: 00000500
find_lb_table: header checksum o.k.
find_lb_table: table checksum o.k.
find_lb_table: record count o.k.
collect_linuxbios_info: Found LinuxBIOS table at: 00000500
malloc_diag: alloc: 128 bytes (3 blocks), free: 16248 bytes (1 blocks)
convert_memmap: 0x00000000000000 0x00000000001000 16
convert_memmap: 0x00000000001000 0x0000000009f000 1
convert_memmap: 0x000000000c0000 0x00000000030000 1
convert_memmap: 0x000000000f0000 0x00000000010000 16
convert_memmap: 0x00000000100000 0x0000007ff00000 1
collect_sys_info: 0000000000001000-00000000000a0000
collect_sys_info: 00000000000c0000-00000000000f0000
collect_sys_info: 0000000000100000-0000000080000000
collect_sys_info: RAM 2048 MB
relocate: Current location: 0x100000-0x13ff67
relocate: Relocating to 0x7ffc0090-0x7ffffff7... ok
setup_timers: CPU 2000 MHz
pci_init: Scanning PCI: found 25 devices
malloc_diag: alloc: 440 bytes (4 blocks), free: 15936 bytes (1 blocks)
pci_init: 00:00.0 10de:0369 0500 00
pci_init: 00:01.0 10de:0360 0601 00
pci_init: 00:01.1 10de:0368 0c05 00
pci_init: 00:01.2 10de:036a 0500 00
pci_init: 00:01.3 10de:036b 0b40 00
pci_init: 00:02.0 10de:036c 0c03 10
pci_init: 00:02.1 10de:036d 0c03 20
pci_init: 00:04.0 10de:036e 0101 8a
pci_init: 00:05.0 10de:037f 0101 85
pci_init: 00:05.1 10de:037f 0101 85
pci_init: 00:05.2 10de:037f 0101 85
pci_init: 00:06.0 10de:0370 0604 00
pci_init: 00:06.1 10de:0371 0403 00
pci_init: 00:08.0 10de:0373 0680 00
pci_init: 00:0a.0 10de:0376 0604 00
pci_init: 00:0b.0 10de:0374 0604 00
pci_init: 00:0c.0 10de:0374 0604 00
pci_init: 00:0d.0 10de:0378 0604 00
pci_init: 00:0e.0 10de:0375 0604 00
pci_init: 00:0f.0 10de:0377 0604 00
pci_init: 00:18.0 1022:1100 0600 00
pci_init: 00:18.1 1022:1101 0600 00
pci_init: 00:18.2 1022:1102 0600 00
pci_init: 00:18.3 1022:1103 0600 00
pci_init: 02:00.0 10de:0392 0300 00
menu: hde1:/boot/grub/menu.lst
malloc_diag: alloc: 456 bytes (5 blocks), free: 15920 bytes (1 blocks)
file_open: dev=hde1, path=/boot/grub/menu.lst
find_ide_controller: found PCI IDE controller 10de:037f prog_if=0x85
find_ide_controller: primary channel: native PCI mode
find_ide_controller: cmd_base=0x3000 ctrl_base=0x3070
ide_software_reset: Waiting for ide2 to become ready for reset... ok
init_drive: Testing for hde
init_drive: Probing for hde
init_drive: LBA mode, sectors=268435455
init_drive: LBA48 mode, sectors=488397168
init_drive: Init device params... ok
hde: LBA48 250GB: WDC WD2500JS-60NCB1
init_drive: Testing for hdf
init_drive: Probing for hdf
print_status: IDE: status=0x0, err=0x0
init_drive: Testing for hdf
init_drive: Probing for hdf
print_status: IDE: status=0x0, err=0x0
devopen: Partition 1 start 63 length 476327187
Mounted ext2fs
malloc_diag: alloc: 440 bytes (4 blocks), free: 15936 bytes (1 blocks)
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press any key to continue.
Press `ESC' to enter the menu... 2 Press `ESC' to enter the menu... 1 Press `ESC' to enter the menu... 0 Booting 'Ubuntu LB, kernel 2.6.21-rc3'
root (hd4,0)
kernel /boot/vmlinuz-2.6.21-rc3 root=/dev/sda1 ro apic=debug acpi_dbg_level=0x
ffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 console=tt
yS0,115200
boot
Booting 'hde1:/boot/vmlinuz-2.6.21-rc3 root=/dev/sda1 ro apic=debug acpi_dbg_le
vel=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 cons
ole=ttyS0,115200'
malloc_diag: alloc: 616 bytes (5 blocks), free: 15760 bytes (1 blocks)
malloc_diag: alloc: 632 bytes (6 blocks), free: 15744 bytes (1 blocks)
file_open: dev=hde1, path=/boot/vmlinuz-2.6.21-rc3
devopen: already open
malloc_diag: alloc: 616 bytes (5 blocks), free: 15760 bytes (1 blocks)
elf_load: Not a bootable ELF image
malloc_diag: alloc: 632 bytes (6 blocks), free: 15744 bytes (1 blocks)
file_open: dev=hde1, path=/boot/vmlinuz-2.6.21-rc3
devopen: already open
malloc_diag: alloc: 616 bytes (5 blocks), free: 15760 bytes (1 blocks)
Found Linux version 2.6.21-rc3 (root at neuromancer) #1 SMP PREEMPT Mon Mar 12 15:10:47 EDT 2007 (protocol 0x204) (loadflags 0x1) bzImage.
init_linux_params: Setting up paramters at 0x90000
set_memory_size: 0000000000001000 - 00000000000a0000
set_memory_size: 00000000000c0000 - 00000000000f0000
set_memory_size: 0000000000100000 - 0000000080000000
set_memory_size: ramtop=0x80000000
set_memory_size: ext_mem_k=64512, alt_mem_k=2096128
parse_command_line: original command line: "root=/dev/sda1 ro apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 console=ttyS0,115200"
parse_command_line: kernel command line at 0x91000
parse_command_line: kernel command line (135 bytes): "root=/dev/sda1 ro apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 console=ttyS0,115200"
load_linux_kernel: offset=0x1e00 addr=0x100000 size=0x1d1473
Loading kernel... ok
start_linux: eip=0x100000
Jumping to entry point...
[ 0.000000] Linux version 2.6.21-rc3 (root at neuromancer) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Mon Mar 12 15:10:47 EDT 2007
[ 0.000000] Command line: root=/dev/sda1 ro apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 console=ttyS0,115200
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000080000000 (usable)
[ 0.000000] end_pfn_map = 524288
[ 0.000000] DMI not present or invalid.
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 1 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[3] active PFN ranges
[ 0.000000] 0: 1 -> 160
[ 0.000000] 0: 192 -> 240
[ 0.000000] 0: 256 -> 524288
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] MPTABLE: OEM ID: GIGABYTE MPTABLE: Product ID: M57SLI MPTABLE: APIC at: 0xFEE00000
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] Processor #1
[ 0.000000] I/O APIC #2 at 0xF6144000.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Processors: 2
[ 0.000000] mapped APIC to ffffffffff5fd000 ( fee00000)
[ 0.000000] mapped IOAPIC to ffffffffff5fc000 (00000000f6144000)
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000c0000
[ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:80000000)
[ 0.000000] PERCPU: Allocating 33216 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 515941
[ 0.000000] Kernel command line: root=/dev/sda1 ro apic=debug acpi_dbg_level=0xffffffff pci=noacpi,routeirq snd-hda-intel.enable_msi=1 console=tty0 console=ttyS0,115200
[ 0.000000] Unknown boot option `snd-hda-intel.enable_msi=1': ignoring
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 44.998202] time.c: Detected 2000.009 MHz processor.
[ 44.999485] Console: colour VGA+ 80x25
[ 45.204471] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 45.212870] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 45.220387] Checking aperture...
[ 45.223654] CPU 0: aperture @ f0000000 size 64 MB
[ 45.244014] Memory: 2060436k/2097152k available (2667k kernel code, 36432k reserved, 1042k data, 244k init)
[ 45.331567] Calibrating delay using timer specific routine.. 4003.32 BogoMIPS (lpj=8006658)
[ 45.340035] Security Framework v1.0.0 initialized
[ 45.344777] SELinux: Disabled at boot.
[ 45.348662] Mount-cache hash table entries: 256
[ 45.353315] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 45.360475] CPU: L2 Cache: 512K (64 bytes/line)
[ 45.365040] CPU: Physical Processor ID: 0
[ 45.369087] CPU: Processor Core ID: 0
[ 45.372804] Freeing SMP alternatives: 28k freed
[ 45.377380] ACPI: Core revision 20070126
[ 45.381363] ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126]
[ 45.391764] ACPI: Unable to load the System Description Tables
[ 45.397647] enabled ExtINT on CPU#0
[ 45.401316] ENABLING IO-APIC IRQs
[ 45.404672] Synchronizing Arb IDs.
[ 45.408138] , 2-5<7>IOAPIC[0]: Set routing entry (2-6 -> 0x36 -> IRQ 6 Mode:0 Active:0)
[ 45.416233] , 2-9<7>IOAPIC[0]: Set routing entry (2-10 -> 0x3a -> IRQ 10 Mode:1 Active:1)
[ 45.424487] , 2-11<7>IOAPIC[0]: Set routing entry (2-12 -> 0x3c -> IRQ 12 Mode:0 Active:0)
[ 45.432873] not connected.
[ 45.435849] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[ 45.481670] testing the IO APIC.......................
[ 45.486846]
[ 45.488573] .................................... done.
[ 45.493744] Using local APIC timer interrupts.
[ 45.548117] result 12500073
[ 45.550950] Detected 12.500 MHz APIC timer.
[ 45.559232] Booting processor 1/2 APIC 0x1
[ 45.573612] Initializing CPU#1
[ 45.574762] masked ExtINT on CPU#1
[ 45.650954] Calibrating delay using timer specific routine.. 4000.27 BogoMIPS (lpj=8000549)
[ 45.650960] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 45.650962] CPU: L2 Cache: 512K (64 bytes/line)
[ 45.650964] CPU: Physical Processor ID: 0
[ 45.650966] CPU: Processor Core ID: 1
[ 45.651039] AMD Processor model unknown stepping 02
[ 45.654971] Brought up 2 CPUs
[ 45.697292] testing NMI watchdog ... OK.
[ 46.378931] migration_cost=158
[ 46.382318] NET: Registered protocol family 16
[ 46.387156] PCI: Using configuration type 1
[ 46.391959] ACPI: Interpreter disabled.
[ 46.395838] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 46.401535] pnp: PnP ACPI: disabled
[ 46.405168] SCSI subsystem initialized
[ 46.409011] PCI: Probing PCI hardware
[ 46.413027] 0000:00:04.0: cannot adjust BAR0 (not I/O)
[ 46.418209] 0000:00:04.0: cannot adjust BAR1 (not I/O)
[ 46.423381] 0000:00:04.0: cannot adjust BAR2 (not I/O)
[ 46.428547] 0000:00:04.0: cannot adjust BAR3 (not I/O)
[ 46.435173] PCI: Using IRQ router default [10de/0370] at 0000:00:06.0
[ 46.441653] querying PCI -> IRQ mapping bus:0, slot:1, pin:0.
[ 46.447432] PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10
[ 46.453298] querying PCI -> IRQ mapping bus:0, slot:1, pin:1.
[ 46.459073] PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10
[ 46.464939] querying PCI -> IRQ mapping bus:0, slot:2, pin:0.
[ 46.470716] PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22
[ 46.476580] querying PCI -> IRQ mapping bus:0, slot:2, pin:1.
[ 46.482359] PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23
[ 46.488223] querying PCI -> IRQ mapping bus:0, slot:5, pin:0.
[ 46.494000] PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20
[ 46.499866] querying PCI -> IRQ mapping bus:0, slot:5, pin:1.
[ 46.505643] PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23
[ 46.511509] querying PCI -> IRQ mapping bus:0, slot:5, pin:2.
[ 46.517286] PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21
[ 46.523153] querying PCI -> IRQ mapping bus:0, slot:6, pin:1.
[ 46.528928] PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23
[ 46.534794] querying PCI -> IRQ mapping bus:0, slot:8, pin:0.
[ 46.540570] PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22
[ 46.546440] querying PCI -> IRQ mapping bus:2, slot:0, pin:0.
[ 46.552215] PCI->APIC IRQ transform: 0000:02:00.0[A] -> IRQ 16
[ 46.558143] NET: Registered protocol family 8
[ 46.562532] NET: Registered protocol family 20
[ 46.567290] PCI: Bridge: 0000:00:06.0
[ 46.569211] Time: tsc clocksource has been installed.
[ 46.576070] IO window: disabled.
[ 46.579510] MEM window: disabled.
[ 46.583032] PREFETCH window: disabled.
[ 46.586994] PCI: Bridge: 0000:00:0a.0
[ 46.590695] IO window: 1000-1fff
[ 46.594129] MEM window: f4000000-f60fffff
[ 46.598342] PREFETCH window: e0000000-efffffff
[ 46.602995] PCI: Bridge: 0000:00:0b.0
[ 46.607540] IO window: disabled.
[ 46.610979] MEM window: disabled.
[ 46.614507] PREFETCH window: disabled.
[ 46.618461] PCI: Bridge: 0000:00:0c.0
[ 46.622154] IO window: disabled.
[ 46.625588] MEM window: disabled.
[ 46.629107] PREFETCH window: disabled.
[ 46.633060] PCI: Bridge: 0000:00:0d.0
[ 46.636755] IO window: disabled.
[ 46.640189] MEM window: disabled.
[ 46.643708] PREFETCH window: disabled.
[ 46.647661] PCI: Bridge: 0000:00:0e.0
[ 46.651355] IO window: disabled.
[ 46.654789] MEM window: disabled.
[ 46.658310] PREFETCH window: disabled.
[ 46.662263] PCI: Bridge: 0000:00:0f.0
[ 46.665954] IO window: disabled.
[ 46.669389] MEM window: disabled.
[ 46.672909] PREFETCH window: disabled.
[ 46.676936] NET: Registered protocol family 2
[ 46.716923] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 46.724360] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 46.733136] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 46.740312] TCP: Hash tables configured (established 131072 bind 65536)
[ 46.746958] TCP reno registered
[ 46.761412] audit: initializing netlink socket (disabled)
[ 46.764840] Time: jiffies clocksource has been installed.
[ 46.772272] audit(1173733921.456:1): initialized
[ 46.777047] VFS: Disk quotas dquot_6.5.1
[ 46.781014] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 46.787570] io scheduler noop registered
[ 46.791572] io scheduler anticipatory registered (default)
[ 46.797195] io scheduler deadline registered
[ 46.801555] io scheduler cfq registered
[ 46.805780] assign_interrupt_mode Found MSI capability
[ 46.811051] assign_interrupt_mode Found MSI capability
[ 46.816307] assign_interrupt_mode Found MSI capability
[ 46.821561] assign_interrupt_mode Found MSI capability
[ 46.826813] assign_interrupt_mode Found MSI capability
[ 46.832066] assign_interrupt_mode Found MSI capability
[ 46.859392] Linux agpgart interface v0.102 (c) Dave Jones
[ 46.864829] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 46.872709] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 46.879584] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 46.887251] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 46.894811] forcedeth: using HIGHDMA
[ 47.419796] eth0: forcedeth.c: subsystem: 01022:2b80 bound to 0000:00:08.0
[ 47.426706] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 47.433088] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 47.441150] NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
[ 47.447279] NFORCE-MCP55: chipset revision 161
[ 47.451751] NFORCE-MCP55: not 100% native mode: will probe irqs later
[ 47.458225] NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
[ 47.464440] ide0: BM-DMA at 0x2cc0-0x2cc7, BIOS settings: hda:pio, hdb:pio
[ 47.874795] hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
[ 48.553523] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 49.126081] hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
[ 49.133741] Uniform CD-ROM driver Revision: 3.20
[ 49.156052] ata1: SATA max UDMA/133 cmd 0x0000000000013000 ctl 0x0000000000013072 bmdma 0x0000000000012cd0 irq 20
[ 49.166365] ata2: SATA max UDMA/133 cmd 0x0000000000013010 ctl 0x0000000000013082 bmdma 0x0000000000012cd8 irq 20
[ 49.176656] scsi0 : sata_nv
[ 49.647166] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 49.663214] ata1.00: ATA-7: WDC WD2500JS-60NCB1, 10.02E02, max UDMA/100
[ 49.669858] ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 49.687162] ata1.00: configured for UDMA/100
[ 49.691466] scsi1 : sata_nv
[ 50.006447] ata2: SATA link down (SStatus 0 SControl 300)
[ 50.022131] ATA: abnormal status 0x7F on port 0x0000000000013017
[ 50.028224] scsi 0:0:0:0: Direct-Access ATA WDC WD2500JS-60N 10.0 PQ: 0 ANSI: 5
[ 50.036416] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 50.043154] sda: Write Protect is off
[ 50.046866] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 50.055885] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 50.062655] sda: Write Protect is off
[ 50.066363] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 50.075350] sda: sda1 sda2 < sda5 >
[ 50.123171] sd 0:0:0:0: Attached scsi disk sda
[ 50.127702] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 50.133099] ata3: SATA max UDMA/133 cmd 0x0000000000013020 ctl 0x0000000000013092 bmdma 0x0000000000012ce0 irq 23
[ 50.143404] ata4: SATA max UDMA/133 cmd 0x0000000000013030 ctl 0x00000000000130a2 bmdma 0x0000000000012ce8 irq 23
[ 50.153696] scsi2 : sata_nv
[ 50.469541] ata3: SATA link down (SStatus 0 SControl 300)
[ 50.485228] ATA: abnormal status 0x7F on port 0x0000000000013027
[ 50.491266] scsi3 : sata_nv
[ 50.808877] ata4: SATA link down (SStatus 0 SControl 300)
[ 50.824559] ATA: abnormal status 0x7F on port 0x0000000000013037
[ 50.830632] ata5: SATA max UDMA/133 cmd 0x0000000000013040 ctl 0x00000000000130b2 bmdma 0x0000000000012cf0 irq 21
[ 50.840935] ata6: SATA max UDMA/133 cmd 0x0000000000013050 ctl 0x00000000000130c2 bmdma 0x0000000000012cf8 irq 21
[ 50.851229] scsi4 : sata_nv
[ 51.168175] ata5: SATA link down (SStatus 0 SControl 300)
[ 51.183859] ATA: abnormal status 0x7F on port 0x0000000000013047
[ 51.189896] scsi5 : sata_nv
[ 51.507511] ata6: SATA link down (SStatus 0 SControl 300)
[ 51.523197] ATA: abnormal status 0x7F on port 0x0000000000013057
[ 51.529324] PNP: No PS/2 controller found. Probing ports directly.
[ 51.535730] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 51.540730] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 51.545863] mice: PS/2 mouse device common for all mice
[ 51.573137] input: AT Translated Set 2 keyboard as /class/input/input0
[ 51.584172] md: raid1 personality registered for level 1
[ 51.589563] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel at redhat.com
[ 51.598171] TCP cubic registered
[ 51.601443] NET: Registered protocol family 1
[ 52.292964] input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
[ 52.333958] md: Autodetecting RAID arrays.
[ 52.338086] md: autorun ...
[ 52.340919] md: ... autorun DONE.
[ 52.366080] kjournald starting. Commit interval 5 seconds
[ 52.366087] EXT3-fs: mounted filesystem with ordered data mode.
[ 52.377556] VFS: Mounted root (ext3 filesystem) readonly.
[ 52.383028] Freeing unused kernel memory: 244k freed
* INIT: version 2.86 booting
* Reading files needed to boot... [ ok ]
* Preparing restricted drivers... [ ok ]
* Starting basic networking... [ ok ]
* Starting kernel event manager... [ ok ]
* Loading hardware drivers... [ 58.597957] usbcore: registered new interface driver usbfs
[ 58.624293] usbcore: registered new interface driver hub
[ 58.630485] usbcore: registered new device driver usb
[ 58.665439] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x2c40
[ 58.671607] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x2c80
[ 58.687747] input: PC Speaker as /class/input/input2
[ 58.778673] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 58.848486] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 58.908346] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 58.914275] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
[ 58.921822] ohci_hcd 0000:00:02.0: irq 22, io mem 0xf6145000
[ 58.987067] usb usb1: configuration #1 chosen from 1 choice
[ 58.992779] hub 1-0:1.0: USB hub found
[ 58.996681] hub 1-0:1.0: 10 ports detected
[ 59.104863] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 59.110204] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 2
[ 59.117725] ehci_hcd 0000:00:02.1: debug port 4
[ 59.122353] ehci_hcd 0000:00:02.1: irq 23, io mem 0xf614a000
[ 59.128109] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 59.135797] usb usb2: configuration #1 chosen from 1 choice
[ 59.141485] hub 2-0:1.0: USB hub found
[ 59.145305] hub 2-0:1.0: 10 ports detected
[ 59.463972] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ ok ]
* Starting PCMCIA services... * PCMCIA not present
* Loading manual drivers... [ 59.779479] Real Time Clock Driver v1.12ac
[ ok ]
[ 60.875180] Adding 6032368k swap on /dev/sda5. Priority:-1 extents:1 across:6032368k
* Checking root file system... /dev/sda1: clean, 199513/29786112 files, 1809651/59540898 blocks
[ ok ]
[ 60.941346] EXT3 FS on sda1, internal journal
* Starting RAID devices... [ ok ]
* Setting up LVM Volume Groups... [ ok ]
* Starting Enterprise Volume Management System... [ 62.082051] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.089575] device-mapper: ioctl: error adding target to table
[ 62.095701] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.103212] device-mapper: ioctl: error adding target to table
[ 62.109309] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.116800] device-mapper: ioctl: error adding target to table
[ 62.122982] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.130492] device-mapper: ioctl: error adding target to table
[ 62.136599] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.144089] device-mapper: ioctl: error adding target to table
[ 62.150159] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.157658] device-mapper: ioctl: error adding target to table
[ 62.163770] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.171284] device-mapper: ioctl: error adding target to table
[ 62.178222] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 62.185736] device-mapper: ioctl: error adding target to table
[ ok ]
* Checking all filesystems... [ ok ]
* Configuring network interfaces... [ 63.781678] NET: Registered protocol family 17
[ ok ]
* INIT: Entering runlevel: 2
* Starting system log... [ ok ]
* Starting kernel log... [ ok ]
* Starting GNOME Display Manager... [ ok ]
* Starting HP Linux Printing and Imaging System [ ok ]
* Starting Common Unix Printing System: cupsd * Starting system message bus dbus [ ok ]
* Starting Hardware abstraction layer hald [ ok ]
* Starting powernowd... * CPU frequency scaling not supported
[ ok ]
* Starting OpenBSD Secure Shell server... [ 70.947096] NET: Registered protocol family 10
[ 70.951641] lo: Disabled Privacy Extensions
[ ok ]
* Starting Bluetooth services... hcid[ 71.197272] Bluetooth: Core ver 2.11
[ 71.200925] NET: Registered protocol family 31
[ 71.205369] Bluetooth: HCI device and connection manager initialized
[ 71.211758] Bluetooth: HCI socket layer initialized
sdpd[ 71.241563] Bluetooth: L2CAP ver 2.8
[ 71.245165] Bluetooth: L2CAP socket layer initialized
[ 71.368677] Bluetooth: RFCOMM socket layer initialized
[ 71.373857] Bluetooth: RFCOMM TTY layer initialized
[ 71.378784] Bluetooth: RFCOMM ver 1.8
[ ok ]
* Starting RAID monitoring services... [ ok ]
* Starting anac(h)ronistic cron: anacron [ ok ]
* Starting deferred execution scheduler... [ ok ]
* Starting periodic command scheduler... [ ok ]
* Checking battery state... [ ok ]
* Running local boot scripts (/etc/rc.local) [ ok ]
Debian GNU/Linux ttyS0 115200 (DIRECT)
**EMSI_REQA77E
neuromancer login: ward
Password:
Last login: Mon Mar 12 17:13:13 2007 on :0
Linux neuromancer 2.6.21-rc3 #1 SMP PREEMPT Mon Mar 12 15:10:47 EDT 2007 x86_64 GNU/Linux
The programs included with the Ubuntu system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
applicable law.
ward at neuromancer:~$ lspci
0000:00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1)
0000:00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2)
0000:00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2)
0000:00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
0000:00:01.3 Co-processor: nVidia Corporation: Unknown device 036b (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
0000:00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
0000:00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
0000:00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:06.0 PCI bridge: nVidia Corporation: Unknown device 0370 (rev a2)
0000:00:06.1 0403: nVidia Corporation: Unknown device 0371 (rev a2)
0000:00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)
0000:00:0a.0 PCI bridge: nVidia Corporation: Unknown device 0376 (rev a2)
0000:00:0b.0 PCI bridge: nVidia Corporation: Unknown device 0374 (rev a2)
0000:00:0c.0 PCI bridge: nVidia Corporation: Unknown device 0374 (rev a2)
0000:00:0d.0 PCI bridge: nVidia Corporation: Unknown device 0378 (rev a2)
0000:00:0e.0 PCI bridge: nVidia Corporation: Unknown device 0375 (rev a2)
0000:00:0f.0 PCI bridge: nVidia Corporation: Unknown device 0377 (rev a2)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
0000:02:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0392 (rev a1)
ward at neuromancer:~$ lspci -tv
-[00]-+-00.0 nVidia Corporation MCP55 Memory Controller
+-01.0 nVidia Corporation MCP55 LPC Bridge
+-01.1 nVidia Corporation MCP55 SMBus
+-01.2 nVidia Corporation MCP55 Memory Controller
+-01.3 nVidia Corporation: Unknown device 036b
+-02.0 nVidia Corporation MCP55 USB Controller
+-02.1 nVidia Corporation MCP55 USB Controller
+-04.0 nVidia Corporation MCP55 IDE
+-05.0 nVidia Corporation MCP55 SATA Controller
+-05.1 nVidia Corporation MCP55 SATA Controller
+-05.2 nVidia Corporation MCP55 SATA Controller
+-06.0-[01]--
+-06.1 nVidia Corporation: Unknown device 0371
+-08.0 nVidia Corporation MCP55 Ethernet
+-0a.0-[02]----00.0 nVidia Corporation: Unknown device 0392
+-0b.0-[03]--
+-0c.0-[04]--
+-0d.0-[05]--
+-0e.0-[06]--
+-0f.0-[07]--
+-18.0 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
+-18.1 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
+-18.2 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
\-18.3 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
ward at neuromancer:~$ cat /proc/interrupts
CPU0 CPU1
0: 306 92902 IO-APIC-edge timer
1: 0 153 IO-APIC-edge i8042
2: 0 0 XT-PIC-XT cascade
4: 0 598 IO-APIC-edge serial
8: 0 0 IO-APIC-edge rtc
12: 2 5625 IO-APIC-edge i8042
14: 8 6784 IO-APIC-edge ide0
20: 7 5275 IO-APIC-fasteoi libata
21: 0 0 IO-APIC-fasteoi libata
22: 0 0 IO-APIC-fasteoi ohci_hcd:usb1
23: 2 863 IO-APIC-fasteoi libata, ehci_hcd:usb2, HDA Intel
NMI: 145 93
LOC: 93132 93079
ERR: 0
ward at neuromancer:~$ cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:04.0
01f0-01f7 : 0000:00:04.0
01f0-01f7 : ide0
0376-0376 : 0000:00:04.0
03c0-03df : vga+
03f6-03f6 : 0000:00:04.0
03f6-03f6 : ide0
03f8-03ff : serial
0cf8-0cff : PCI conf1
1000-1fff : PCI Bus #02
1000-107f : 0000:02:00.0
2c00-2c3f : 0000:00:01.1
2c40-2c7f : 0000:00:01.1
2c40-2c7f : nForce2_smbus
2c80-2cbf : 0000:00:01.1
2c80-2cbf : nForce2_smbus
2cc0-2ccf : 0000:00:04.0
2cc0-2cc7 : ide0
2cd0-2cdf : 0000:00:05.0
2cd0-2cdf : sata_nv
2ce0-2cef : 0000:00:05.1
2ce0-2cef : sata_nv
2cf0-2cff : 0000:00:05.2
2cf0-2cff : sata_nv
3000-3007 : 0000:00:05.0
3000-3007 : sata_nv
3010-3017 : 0000:00:05.0
3010-3017 : sata_nv
3020-3027 : 0000:00:05.1
3020-3027 : sata_nv
3030-3037 : 0000:00:05.1
3030-3037 : sata_nv
3040-3047 : 0000:00:05.2
3040-3047 : sata_nv
3050-3057 : 0000:00:05.2
3050-3057 : sata_nv
3060-3067 : 0000:00:08.0
3060-3067 : forcedeth
3070-3073 : 0000:00:05.0
3070-3073 : sata_nv
3080-3083 : 0000:00:05.0
3080-3083 : sata_nv
3090-3093 : 0000:00:05.1
3090-3093 : sata_nv
30a0-30a3 : 0000:00:05.1
30a0-30a3 : sata_nv
30b0-30b3 : 0000:00:05.2
30b0-30b3 : sata_nv
30c0-30c3 : 0000:00:05.2
30c0-30c3 : sata_nv
root at neuromancer:~# halt
Broadcast message from root at neuromancer (ttyS0) (Mon Mar 12 17:21:04 2007):
The system is goi * Stopping GNOME Display Manager... [ ok ]
* Stopping anac(h)ronistic cron: anacron [ ok ]
* Stopping deferred execution scheduler... [ ok ]
* Stopping periodic command scheduler... [ ok ]
* Stopping Common Unix Printing System: cupsd [ ok ]
* Disabling power management... [ ok ]
* Stopping BitTorrent tracker: bttrack.bittorrent * Stopping Hardware abstraction layer hald [ ok ]
* Stopping system message bus dbus [ ok ]
KDSETKEYCODE: Invalid argument
failed to set scancode 0 to keycode 256
* Stopping powernowd: [ ok ]
* Stopping rsync daemon: rsync [ ok ]
* Stopping OpenBSD Secure Shell server... [ ok ]
* Stopping HP Linux Printing and Imaging System [ ok ]
* Stopping RAID monitoring services... [ ok ]
* Shutting down ALSA... [ ok ]
* Stopping Bluetooth services... sdpd hcid[ ok ]
* Stopping kernel log... [ ok ]
* Stopping system log... [ ok ]
* Terminating any remaining processes... [ ok ]
* Unmounting remote filesystems... [ ok ]
* Deconfiguring network interfaces... [ ok ]
* Unmounting local filesystems... [ ok ]
* Deactivating swap... [ ok ]
* Shutting down LVM Volume Groups... [ ok ]
* Will now halt
[ 603.647885] md: stopping all md devices.
[ 605.468150] Synchronizing SCSI cache for disk sda:
[ 605.473304] System halted.
-------------- next part --------------
[ 0.000000] Linux version 2.6.21-rc3 (root at neuromancer) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Mon Mar 12 15:10:47 EDT 2007
[ 0.000000] Command line: root=/dev/sda1 ro console=tty0 console=ttyS0,115200 noapic
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
[ 0.000000] BIOS-e820: 000000007fff0000 - 000000007fff3000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007fff3000 - 0000000080000000 (ACPI data)
[ 0.000000] BIOS-e820: 00000000d0000000 - 00000000e0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f8000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP 000F6790, 0014 (r0 Nvidia)
[ 0.000000] ACPI: RSDT 7FFF3000, 0034 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: FACP 7FFF3040, 0074 (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: DSDT 7FFF30C0, 4B21 (r1 NVIDIA AWRDACPI 1000 MSFT 100000C)
[ 0.000000] ACPI: FACS 7FFF0000, 0040
[ 0.000000] ACPI: SSDT 7FFF7C80, 01C4 (r1 PTLTD POWERNOW 1 LTP 1)
[ 0.000000] ACPI: MCFG 7FFF7E80, 003C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] ACPI: APIC 7FFF7C00, 007C (r1 Nvidia AWRDACPI 42302E31 AWRD 1010101)
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 524272
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
[ 0.000000] ACPI: Skipping IOAPIC probe due to 'noapic' option.
[ 0.000000] Using ACPI for processor (LAPIC) configuration information
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] MPTABLE: OEM ID: OEM00000 MPTABLE: Product ID: PROD00000000 MPTABLE: APIC at: 0xFEE00000
[ 0.000000] I/O APIC #2 at 0xFEC00000.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Processors: 2
[ 0.000000] Nosave address range: 000000000009f000 - 00000000000a0000
[ 0.000000] Nosave address range: 00000000000a0000 - 00000000000f0000
[ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:50000000)
[ 0.000000] PERCPU: Allocating 33216 bytes of per cpu data
[ 0.000000] Built 1 zonelists. Total pages: 515875
[ 0.000000] Kernel command line: root=/dev/sda1 ro console=tty0 console=ttyS0,115200 noapic
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 27.500859] time.c: Detected 2010.333 MHz processor.
[ 27.502086] Console: colour VGA+ 80x25
[ 27.809799] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 27.818130] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 27.825626] Checking aperture...
[ 27.828892] CPU 0: aperture @ 3ffc000000 size 32 MB
[ 27.833800] Aperture too small (32 MB)
[ 27.842265] No AGP bridge found
[ 27.860671] Memory: 2059980k/2097088k available (2667k kernel code, 36440k reserved, 1042k data, 244k init)
[ 27.946554] Calibrating delay using timer specific routine.. 4023.93 BogoMIPS (lpj=8047869)
[ 27.955009] Security Framework v1.0.0 initialized
[ 27.959740] SELinux: Disabled at boot.
[ 27.963620] Mount-cache hash table entries: 256
[ 27.968267] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 27.975425] CPU: L2 Cache: 512K (64 bytes/line)
[ 27.979986] CPU: Physical Processor ID: 0
[ 27.984029] CPU: Processor Core ID: 0
[ 27.987732] Freeing SMP alternatives: 28k freed
[ 27.992306] ACPI: Core revision 20070126
[ 27.998505] ACPI: setting ELCR to 0200 (from 8c20)
[ 28.004780] Using local APIC timer interrupts.
[ 28.058966] result 12564597
[ 28.061794] Detected 12.564 MHz APIC timer.
[ 28.066563] Booting processor 1/2 APIC 0x1
[ 28.080537] Initializing CPU#1
[ 28.158006] Calibrating delay using timer specific routine.. 4027.93 BogoMIPS (lpj=8055863)
[ 28.158012] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 28.158014] CPU: L2 Cache: 512K (64 bytes/line)
[ 28.158016] CPU: Physical Processor ID: 0
[ 28.158017] CPU: Processor Core ID: 1
[ 28.158088] AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
[ 28.162433] Brought up 2 CPUs
[ 28.202881] testing NMI watchdog ... OK.
[ 28.865808] migration_cost=156
[ 28.869549] NET: Registered protocol family 16
[ 28.874098] ACPI: bus type pci registered
[ 28.879680] PCI: Using MMCONFIG at f0000000 - f7ffffff
[ 28.884869] PCI: No mmconfig possible on device 00:18
[ 28.894859] ACPI: Interpreter enabled
[ 28.898563] ACPI: Using PIC for interrupt routing
[ 28.913087] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 28.918140] 0000:00:04.0: cannot adjust BAR0 (not I/O)
[ 28.923331] 0000:00:04.0: cannot adjust BAR1 (not I/O)
[ 28.928117] 0000:00:04.0: cannot adjust BAR2 (not I/O)
[ 28.933289] 0000:00:04.0: cannot adjust BAR3 (not I/O)
[ 28.938713] PCI: Transparent bridge - 0000:00:06.0
[ 28.998648] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.006899] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.015151] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15)
[ 29.022193] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.030455] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.038716] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.046978] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 *15)
[ 29.054019] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.062280] ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.071400] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 10 11 14 *15)
[ 29.078441] ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
[ 29.085481] ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 *11 14 15)
[ 29.092512] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.100766] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15)
[ 29.107808] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
[ 29.114848] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
[ 29.123103] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 11 14 *15)
[ 29.130143] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15)
[ 29.137165] ACPI: PCI Interrupt Link [LSA2] (IRQs 5 7 9 10 *11 14 15)
[ 29.144234] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
[ 29.150956] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
[ 29.157674] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
[ 29.164386] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
[ 29.171105] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
[ 29.177827] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
[ 29.184539] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
[ 29.191259] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
[ 29.197979] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
[ 29.205609] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
[ 29.213229] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
[ 29.220851] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
[ 29.228472] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
[ 29.236101] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
[ 29.243732] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
[ 29.251361] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
[ 29.258990] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
[ 29.266621] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
[ 29.274252] ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0, disabled.
[ 29.281775] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 29.287476] pnp: PnP ACPI init
[ 29.294875] pnp: PnP ACPI: found 14 devices
[ 29.299206] SCSI subsystem initialized
[ 29.303063] PCI: Using ACPI for IRQ routing
[ 29.307285] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 29.315643] NET: Registered protocol family 8
[ 29.320039] NET: Registered protocol family 20
[ 29.324601] pnp: 00:01: ioport range 0x1000-0x107f has been reserved
[ 29.325609] Time: tsc clocksource has been installed.
[ 29.336063] pnp: 00:01: ioport range 0x1080-0x10ff has been reserved
[ 29.342454] pnp: 00:01: ioport range 0x1400-0x147f has been reserved
[ 29.348837] pnp: 00:01: ioport range 0x1480-0x14ff has been reserved
[ 29.355227] pnp: 00:01: ioport range 0x1800-0x187f has been reserved
[ 29.361610] pnp: 00:01: ioport range 0x1880-0x18ff has been reserved
[ 29.367993] pnp: 00:01: iomem range 0xd0000000-0xdfffffff has been reserved
[ 29.374989] pnp: 00:0c: iomem range 0xf0000000-0xf7ffffff has been reserved
[ 29.381982] pnp: 00:0d: iomem range 0xd0000-0xd3fff has been reserved
[ 29.388457] pnp: 00:0d: iomem range 0xf0000-0xf7fff could not be reserved
[ 29.395272] pnp: 00:0d: iomem range 0xf8000-0xfbfff could not be reserved
[ 29.402090] pnp: 00:0d: iomem range 0xfc000-0xfffff could not be reserved
[ 29.409118] PCI: Bridge: 0000:00:06.0
[ 29.409554] Time: acpi_pm clocksource has been installed.
[ 29.418239] IO window: disabled.
[ 29.421676] MEM window: fb000000-fb0fffff
[ 29.425894] PREFETCH window: disabled.
[ 29.429853] PCI: Bridge: 0000:00:0a.0
[ 29.433549] IO window: 9000-9fff
[ 29.436978] MEM window: f8000000-faffffff
[ 29.441196] PREFETCH window: e0000000-efffffff
[ 29.445880] NET: Registered protocol family 2
[ 29.489070] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 29.496494] TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
[ 29.505247] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 29.512421] TCP: Hash tables configured (established 131072 bind 65536)
[ 29.519073] TCP reno registered
[ 29.533667] audit: initializing netlink socket (disabled)
[ 29.539108] audit(1173735859.668:1): initialized
[ 29.543884] VFS: Disk quotas dquot_6.5.1
[ 29.547856] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 29.554423] io scheduler noop registered
[ 29.558426] io scheduler anticipatory registered (default)
[ 29.564028] io scheduler deadline registered
[ 29.568385] io scheduler cfq registered
[ 29.613132] assign_interrupt_mode Found MSI capability
[ 29.641630] Linux agpgart interface v0.102 (c) Dave Jones
[ 29.647073] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 29.654962] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.661561] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 29.667783] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 29.675453] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
[ 29.683267] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 5
[ 29.688967] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LMAC] -> GSI 5 (level, low) -> IRQ 5
[ 29.697623] forcedeth: using HIGHDMA
[ 30.224777] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:08.0
[ 30.231693] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 30.238082] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 30.246153] NFORCE-MCP55: IDE controller at PCI slot 0000:00:04.0
[ 30.252287] NFORCE-MCP55: chipset revision 161
[ 30.256768] NFORCE-MCP55: not 100% native mode: will probe irqs later
[ 30.263239] NFORCE-MCP55: BIOS didn't set cable bits correctly. Enabling workaround.
[ 30.271025] NFORCE-MCP55: 0000:00:04.0 (rev a1) UDMA133 controller
[ 30.277244] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[ 31.023989] hda: PIONEER DVD-RW DVR-111D, ATAPI CD/DVD-ROM drive
[ 31.703641] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 32.271886] hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(66)
[ 32.279484] Uniform CD-ROM driver Revision: 3.20
[ 32.302850] ACPI: PCI Interrupt Link [LSID] enabled at IRQ 15
[ 32.308639] ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LSID] -> GSI 15 (level, low) -> IRQ 15
[ 32.317518] ata1: SATA max UDMA/133 cmd 0x000000000001a400 ctl 0x000000000001a802 bmdma 0x000000000001b400 irq 15
[ 32.327840] ata2: SATA max UDMA/133 cmd 0x000000000001ac00 ctl 0x000000000001b002 bmdma 0x000000000001b408 irq 15
[ 32.338140] scsi0 : sata_nv
[ 32.811021] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 32.845051] ata1.00: ATA-7: WDC WD2500JS-60NCB1, 10.02E02, max UDMA/100
[ 32.851700] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 32.884943] ata1.00: configured for UDMA/100
[ 32.889253] scsi1 : sata_nv
[ 33.206716] ata2: SATA link down (SStatus 0 SControl 300)
[ 33.222416] ATA: abnormal status 0x7F on port 0x000000000001ac07
[ 33.228515] scsi 0:0:0:0: Direct-Access ATA WDC WD2500JS-60N 10.0 PQ: 0 ANSI: 5
[ 33.236719] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 33.243086] sda: Write Protect is off
[ 33.246804] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.255837] SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
[ 33.262991] sda: Write Protect is off
[ 33.266694] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 33.275691] sda: sda1 sda2 < sda5 >
[ 33.323987] sd 0:0:0:0: Attached scsi disk sda
[ 33.328516] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 33.334115] ACPI: PCI Interrupt Link [LFID] enabled at IRQ 10
[ 33.339905] ACPI: PCI Interrupt 0000:00:05.1[B] -> Link [LFID] -> GSI 10 (level, low) -> IRQ 10
[ 33.348766] ata3: SATA max UDMA/133 cmd 0x000000000001b800 ctl 0x000000000001bc02 bmdma 0x000000000001c800 irq 10
[ 33.359084] ata4: SATA max UDMA/133 cmd 0x000000000001c000 ctl 0x000000000001c402 bmdma 0x000000000001c808 irq 10
[ 33.369385] scsi2 : sata_nv
[ 33.686366] ata3: SATA link down (SStatus 0 SControl 300)
[ 33.702064] ATA: abnormal status 0x7F on port 0x000000000001b807
[ 33.708106] scsi3 : sata_nv
[ 34.026118] ata4: SATA link down (SStatus 0 SControl 300)
[ 34.041815] ATA: abnormal status 0x7F on port 0x000000000001c007
[ 34.048105] ACPI: PCI Interrupt Link [LSA2] enabled at IRQ 11
[ 34.053885] ACPI: PCI Interrupt 0000:00:05.2[C] -> Link [LSA2] -> GSI 11 (level, low) -> IRQ 11
[ 34.062740] ata5: SATA max UDMA/133 cmd 0x000000000001cc00 ctl 0x000000000001d002 bmdma 0x000000000001dc00 irq 11
[ 34.073052] ata6: SATA max UDMA/133 cmd 0x000000000001d400 ctl 0x000000000001d802 bmdma 0x000000000001dc08 irq 11
[ 34.083350] scsi4 : sata_nv
[ 34.397847] ata5: SATA link down (SStatus 0 SControl 300)
[ 34.413549] ATA: abnormal status 0x7F on port 0x000000000001cc07
[ 34.419589] scsi5 : sata_nv
[ 34.737599] ata6: SATA link down (SStatus 0 SControl 300)
[ 34.753298] ATA: abnormal status 0x7F on port 0x000000000001d407
[ 34.759420] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 34.767241] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 34.772282] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 34.777444] mice: PS/2 mouse device common for all mice
[ 34.805824] input: AT Translated Set 2 keyboard as /class/input/input0
[ 34.816424] md: raid1 personality registered for level 1
[ 34.821819] device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel at redhat.com
[ 34.830413] TCP cubic registered
[ 34.833683] NET: Registered protocol family 1
[ 35.516051] input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
[ 35.569051] md: Autodetecting RAID arrays.
[ 35.573186] md: autorun ...
[ 35.576014] md: ... autorun DONE.
[ 35.594625] kjournald starting. Commit interval 5 seconds
[ 35.600151] EXT3-fs: mounted filesystem with ordered data mode.
[ 35.606993] VFS: Mounted root (ext3 filesystem) readonly.
[ 35.612468] Freeing unused kernel memory: 244k freed
* INIT: version 2.86 booting
* Reading files needed to boot... [ ok ]
* Preparing restricted drivers... [ ok ]
* Starting basic networking... [ ok ]
* Starting kernel event manager... [ ok ]
* Loading hardware drivers... error receiving uevent message: No buffer space available
[ ok ]
* Starting PCMCIA services... * PCMCIA not present
* Loading manual drivers... [ 41.235517] Real Time Clock Driver v1.12ac
[ ok ]
* Checking root file system... /dev/shm/root: clean, 199517/29786112 files, 1809759/59540898 blocks (check in 3 mounts)
[ ok ]
[ 41.445880] EXT3 FS on sda1, internal journal
* Starting RAID devices... [ 41.868682] i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00
[ 41.874762] i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c80
[ 41.907746] usbcore: registered new interface driver usbfs
[ 41.913529] usbcore: registered new interface driver hub
[ 41.919059] usbcore: registered new device driver usb
[ 42.045856] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 5
[ 42.051713] ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUB2] -> GSI 5 (level, low) -> IRQ 5
[ 42.060650] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 42.066589] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 42.084625] ehci_hcd 0000:00:02.1: debug port 4
[ 42.089360] ehci_hcd 0000:00:02.1: irq 5, io mem 0xfb106000
[ 42.095156] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 42.103021] usb usb1: configuration #1 chosen from 1 choice
[ 42.108832] hub 1-0:1.0: USB hub found
[ 42.112749] hub 1-0:1.0: 10 ports detected
[ 42.178408] input: PC Speaker as /class/input/input2
[ 42.184087] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 42.226792] ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 15
[ 42.233719] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUBA] -> GSI 15 (level, low) -> IRQ 15
[ 42.242894] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 42.248372] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
[ 42.248417] Floppy drive(s): fd0 is 1.44M
[ 42.260227] ohci_hcd 0000:00:02.0: irq 15, io mem 0xfb105000
[ 42.271346] FDC 0 is a post-1991 82077
[ 42.288336] NET: Registered protocol family 17
[ 42.328273] usb usb2: configuration #1 chosen from 1 choice
[ 42.334095] hub 2-0:1.0: USB hub found
[ 42.338000] hub 2-0:1.0: 10 ports detected
[ 42.447943] ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 10
[ 42.453913] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNK3] -> GSI 10 (level, low) -> IRQ 10
[ 42.484426] parport: PnPBIOS parport detected.
[ 42.489228] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 42.531125] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[fb004000-fb0047ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 42.544325] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ ok ]
[ 43.182589] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 11
[ 43.188539] ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [LAZA] -> GSI 11 (level, low) -> IRQ 11
* Setting up LVM Volume Groups... [ 43.407187] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ ok ]
* Starting Enterprise Volume Management System... [ 44.390274] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.397943] device-mapper: ioctl: error adding target to table
[ 44.404468] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.412140] device-mapper: ioctl: error adding target to table
[ 44.418388] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.426043] device-mapper: ioctl: error adding target to table
[ 44.432313] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.439985] device-mapper: ioctl: error adding target to table
[ 44.446247] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.453929] device-mapper: ioctl: error adding target to table
[ 44.460136] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.467795] device-mapper: ioctl: error adding target to table
[ 44.474048] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.481720] device-mapper: ioctl: error adding target to table
[ 44.487926] device-mapper: table: 238:0: linear: dm-linear: Device lookup failed
[ 44.495594] device-mapper: ioctl: error adding target to table
[ ok ]
* Checking all filesystems... [ ok ]
[ 44.600759] Adding 6032368k swap on /dev/sda5. Priority:-1 extents:1 across:6032368k
* Configuring network interfaces... [ ok ]
* INIT: Entering runlevel: 2
* Loading ACPI modules... [ ok ]
* Starting ACPI services... [ ok ]
* Starting system log... [ ok ]
* Starting kernel log... [ ok ]
* Starting GNOME Display Manager... [ ok ]
* Starting HP Linux Printing and Imaging System [ ok ]
* Starting Common Unix Printing System: cupsd * Starting system message bus dbus [ ok ]
* Starting Hardware abstraction layer hald [ ok ]
* Starting powernowd... [ ok ]
* Starting OpenBSD Secure Shell server... [ ok ]
* Starting Bluetooth services... hcid[ 53.697214] Bluetooth: Core ver 2.11
[ 53.701010] NET: Registered protocol family 31
[ 53.705602] Bluetooth: HCI device and connection manager initialized
[ 53.712141] Bluetooth: HCI socket layer initialized
sdpd[ 53.768781] Bluetooth: L2CAP ver 2.8
[ 53.772527] Bluetooth: L2CAP socket layer initialized
[ 54.037519] Bluetooth: RFCOMM socket layer initialized
[ 54.042881] Bluetooth: RFCOMM TTY layer initialized
[ 54.047922] Bluetooth: RFCOMM ver 1.8
[ ok ]
* Starting RAID monitoring services... [ ok ]
* Starting anac(h)ronistic cron: anacron [ ok ]
* Starting deferred execution scheduler... [ ok ]
* Starting periodic command scheduler... [ ok ]
* Checking battery state... [ ok ]
* Running local boot scripts (/etc/rc.local) [ ok ]
Debian GNU/Linux ttyS0 115200 (DIRECT)
**EMSI_REQA77E
neuromancer login: ward
Password:
Last login: Mon Mar 12 17:44:42 2007 on :0
Linux neuromancer 2.6.21-rc3 #1 SMP PREEMPT Mon Mar 12 15:10:47 EDT 2007 x86_64 GNU/Linux
The programs included with the Ubuntu system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Ubuntu comes with ABSOLUTELY NO WARRANTY, to the extent permitted by
applicable law.
ward at neuromancer:~$ lspci
0000:00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a1)
0000:00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a2)
0000:00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a2)
0000:00:01.2 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2)
0000:00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1)
0000:00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2)
0000:00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1)
0000:00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a2)
0000:00:06.0 PCI bridge: nVidia Corporation: Unknown device 0370 (rev a2)
0000:00:06.1 0403: nVidia Corporation: Unknown device 0371 (rev a2)
0000:00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a2)
0000:00:0a.0 PCI bridge: nVidia Corporation: Unknown device 0376 (rev a2)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
0000:01:0a.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
0000:02:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0392 (rev a1)
ward at neuromancer:~$ lspci -tv
-[00]-+-00.0 nVidia Corporation MCP55 Memory Controller
+-01.0 nVidia Corporation MCP55 LPC Bridge
+-01.1 nVidia Corporation MCP55 SMBus
+-01.2 nVidia Corporation MCP55 Memory Controller
+-02.0 nVidia Corporation MCP55 USB Controller
+-02.1 nVidia Corporation MCP55 USB Controller
+-04.0 nVidia Corporation MCP55 IDE
+-05.0 nVidia Corporation MCP55 SATA Controller
+-05.1 nVidia Corporation MCP55 SATA Controller
+-05.2 nVidia Corporation MCP55 SATA Controller
+-06.0-[01]----0a.0 Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
+-06.1 nVidia Corporation: Unknown device 0371
+-08.0 nVidia Corporation MCP55 Ethernet
+-0a.0-[02]----00.0 nVidia Corporation: Unknown device 0392
+-18.0 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
+-18.1 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
+-18.2 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
\-18.3 Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
ward at neuromancer:~$ cat /proc/interrupts
CPU0 CPU1
0: 35639 2458 XT-PIC-XT timer
1: 20 0 XT-PIC-XT i8042
2: 0 0 XT-PIC-XT cascade
4: 409 135 XT-PIC-XT serial
5: 0 0 XT-PIC-XT ehci_hcd:usb1
6: 3 2 XT-PIC-XT floppy
7: 4197 44509 XT-PIC-XT parport0
8: 0 0 XT-PIC-XT rtc
9: 0 0 XT-PIC-XT acpi
10: 1 2 XT-PIC-XT libata, ohci1394
11: 668 168 XT-PIC-XT libata, HDA Intel
12: 820 243 XT-PIC-XT i8042
14: 2715 387 XT-PIC-XT ide0
15: 4346 965 XT-PIC-XT libata, ohci_hcd:usb2
510: 15 14607 PCI-MSI-edge eth0
NMI: 74 40
LOC: 37969 37992
ERR: 5524
ward at neuromancer:~$ cat /proc/ipoports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:04.0
01f0-01f7 : 0000:00:04.0
01f0-01f7 : ide0
0376-0376 : 0000:00:04.0
0378-037a : parport0
03c0-03df : vga+
03f2-03f5 : floppy
03f6-03f6 : 0000:00:04.0
03f6-03f6 : ide0
03f7-03f7 : floppy DIR
03f8-03ff : serial
0cf8-0cff : PCI conf1
1000-107f : pnp 00:01
1000-1003 : ACPI PM1a_EVT_BLK
1004-1005 : ACPI PM1a_CNT_BLK
1008-100b : ACPI PM_TMR
101c-101c : ACPI PM2_CNT_BLK
1020-1027 : ACPI GPE0_BLK
1080-10ff : pnp 00:01
1400-147f : pnp 00:01
1480-14ff : pnp 00:01
14a0-14af : ACPI GPE1_BLK
1800-187f : pnp 00:01
1880-18ff : pnp 00:01
1c00-1c3f : 0000:00:01.1
1c00-1c3f : nForce2_smbus
1c80-1cbf : 0000:00:01.1
1c80-1cbf : nForce2_smbus
9000-9fff : PCI Bus #02
9000-907f : 0000:02:00.0
a400-a407 : 0000:00:05.0
a400-a407 : sata_nv
a800-a803 : 0000:00:05.0
a800-a803 : sata_nv
ac00-ac07 : 0000:00:05.0
ac00-ac07 : sata_nv
b000-b003 : 0000:00:05.0
b000-b003 : sata_nv
b400-b40f : 0000:00:05.0
b400-b40f : sata_nv
b800-b807 : 0000:00:05.1
b800-b807 : sata_nv
bc00-bc03 : 0000:00:05.1
bc00-bc03 : sata_nv
c000-c007 : 0000:00:05.1
c000-c007 : sata_nv
c400-c403 : 0000:00:05.1
c400-c403 : sata_nv
c800-c80f : 0000:00:05.1
c800-c80f : sata_nv
cc00-cc07 : 0000:00:05.2
cc00-cc07 : sata_nv
d000-d003 : 0000:00:05.2
d000-d003 : sata_nv
d400-d407 : 0000:00:05.2
d400-d407 : sata_nv
d800-d803 : 0000:00:05.2
d800-d803 : sata_nv
dc00-dc0f : 0000:00:05.2
dc00-dc0f : sata_nv
e000-e007 : 0000:00:08.0
e000-e007 : forcedeth
f000-f00f : 0000:00:04.0
f000-f007 : ide0
ward at neuromancer:~$ cat /proc/mtrr
reg00: base=0x00000000 ( 0MB), size=2048MB: write-back, count=1
ward at neuromancer:~$ lspci -vxxx
pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.pcilib: sysfs_read: tried to read 256 bytes at 0, but got only 64
Unable to read 256 bytes of configuration space.
ward at neuromancer:~$ sudo halt
Password:
Broadcast message from root at neuromancer (ttyS0) (Mon Mar 12 17:48:29 2007):
T * INIT: Sending processe * Stopping GNOME Display Manager... [ ok ]
* Stopping anac(h)ronistic cron: anacron [ ok ]
* Stopping deferred execution scheduler... [ ok ]
* Stopping periodic command scheduler... [ ok ]
* Stopping Common Unix Printing System: cupsd [ ok ]
* Disabling power management... [ ok ]
* Stopping BitTorrent tracker: bttrack.bittorrent * Stopping Hardware abstraction layer hald [ ok ]
* Stopping system message bus dbus [ ok ]
KDSETKEYCODE: Invalid argument
failed to set scancode 0 to keycode 256
* Stopping powernowd: [ ok ]
* Stopping rsync daemon: rsync [ ok ]
* Stopping OpenBSD Secure Shell server... [ ok ]
* Stopping ACPI services... [ ok ]
* Stopping HP Linux Printing and Imaging System [ ok ]
* Stopping RAID monitoring services... [ ok ]
* Shutting down ALSA... [ ok ]
* Stopping Bluetooth services... sdpd hcid[ ok ]
* Stopping kernel log... [ ok ]
* Stopping system log... [ ok ]
* Terminating any remaining processes... [ ok ]
* Unmounting remote filesystems... [ ok ]
* Deconfiguring network interfaces... [ ok ]
* Unmounting local filesystems... [ ok ]
* Deactivating swap... [ ok ]
* Shutting down LVM Volume Groups... [ ok ]
* Will now halt
[ 185.152428] md: stopping all md devices.
[ 186.979399] Synchronizing SCSI cache for disk sda:
[ 186.986336] Power down.
[ 186.988897] acpi_power_off called
More information about the coreboot
mailing list