[LinuxBIOS] PIRQ REF DES AMD LXUVCRDK
Marc Jones
marc.jones at amd.com
Wed Jun 20 23:03:06 CEST 2007
Otávio Alcântara wrote:
> Thanks for the help. But I have another doubt, I'm not getting video
> working even after the linux kernel boots. What do I do to change the
> console to video? I've configured Filo to use video console, but the
> stream goes only to serial interface.
>
> Regards,
>
> Otávio Alcântara
>
Otávio,
Correct, you can't get graphics until a driver is loaded. For a
test/debug setup that uses the filo menu will only be visable serial.
Please see this link for the Geode LX framebuffer support.
http://thread.gmane.org/gmane.linux.fbdev.devel/10339
Marc
> On 6/20/07, *Marc Jones* <marc.jones at amd.com
> <mailto:marc.jones at amd.com>> wrote:
>
>
>
> Otávio Alcântara wrote:
> > Hello to all,
> >
> > I'm porting a linuxbios v2 version for a board ref des
> > LXUVCRDK (http://www.amd.com/geodelxuvcrdk
> <http://www.amd.com/geodelxuvcrdk>) based on norwich board. I've
> > already got to boot linux from HD, but it seems to halt in some point
> > (see log below captured from serial). Although, I'm using VSA
> > (lx_vsa.36k.bin) and I got no output from video VGA.
> > I'd like some help for setting up the PIRQ table and
> for VGA
> > setup.
> >
> > PS: The schematics for this board are publicly available from AMD
> > Embedded Developer Web Site.
> >
> > Thanks,
> >
> > --
> > Otávio Alcântara
> > "I'll never cross to the Dark Side."
> >
> >
> >
>
> I took a quick look at the schematics and I think that this is what the
> PIRQ table should look like.
>
> /* If you change the number of entries, change the IRQ_SLOT_COUNT
> above! */
> /* bus, dev|fn, {link, bitmap}, {link, bitmap},
> {link, bitmap}, {link, bitmap}, slot, rfu */
> {0x00, (0x01 << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00,
> 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* cpu */
> {0x00, (0x0F << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {L_PIRQB, M_PIRQB},
> {L_PIRQC, M_PIRQC}, {L_PIRQD, M_PIRQD}}, 0x0, 0x0}, /* chipset */
> {0x00, (0x0D << 3) | 0x0, {{L_PIRQA, M_PIRQA}, {0x00, 0x00}, {0x00,
> 0x00}, {0x00, 0x00}}, 0x0, 0x0}, /* ethernet */
>
> Make sure to change IRQ_SLOT_COUNT in the mainboard Options.lb
> <http://Options.lb>
>
> As Jordan pointed out, you should use the Linux framebuffer and X
> drivers instead of VGA. That means that you should also set
> CONFIG_CONSOLE_VGA=0 and CONFIG_PCI_ROM_RUN=0 in Options.lb
> <http://Options.lb>
>
>
> It also looks like there is something funny going on with the
> Config.lb <http://Config.lb>.
> Try using the norwich one without modifications.
>
> > cs5536: southbridge_init: enable_ide_nand_flash is 36
> If you want to boot from IDE enable_ide_nand_flash should be 0
>
> > Disabling VPCI device: 0x0000106C
> > Disabling VPCI device: 0x00001075
> > Disabling VPCI device: 0x0000107E
> > Disabling VPCI device: 0x00001087
> > Disabling VPCI device: 0x00001090
> > Disabling VPCI device: 0x00001099
> > Disabling VPCI device: 0x000010A2
> > Disabling VPCI device: 0x000010AB
> This is a very strange list.
>
>
> I don't have one of these boards so when you get it working please
> submit a patch!
> Let me know if there is anything else I can do to help
>
> Marc
>
>
>
> >
> > LinuxBIOS-2.0.0.0Fallback Qua Jun 20 07:45:43 BRT 2007 starting...
> > _MSR GLCP_SYS_RSTPLL (4c000014) value is: 00000498:00001820
> > Configuring PLL
> >
> >
> > LinuxBIOS-2.0.0.0Fallback Qua Jun 20 07:45:43 BRT 2007 starting...
> > _MSR GLCP_SYS_RSTPLL (4c000014) value is: 00000498:07de0020
> > Done cpuRegInit
> > SMBUS READ ERROR:03 device:a2
> > Ram1.00
> > Ram2.00
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > SMBUS READ ERROR:03 device:a2
> > Ram3
> > DRAM controller init done.
> > RAM DLL lock
> > Ram4
> > Copying LinuxBIOS to ram.
> > Jumping to LinuxBIOS.
> > LinuxBIOS-2.0.0.0Fallback Qua Jun 20 08:56:35 BRT 2007 booting...
> > clocks_per_usec: 432
> > Enumerating buses...
> > >> Entering northbridge.c: pci_domain_enable
> > Enter northbridge_init_early
> > writeglmsr: MSR 0x10000020, val 0x20000000:0x000fff80
> > writeglmsr: MSR 0x10000021, val 0x20000000:0x080fffe0
> > writeglmsr: MSR 0x1000002c, val 0x20000000:0x00000003
> > sizeram: _MSR MC_CF07_DATA: 10076112:00004840
> > sizeram: sizem 0x100MB
> > SysmemInit: enable for 256MBytes
> > usable RAM: 268304383 bytes
> > SysmemInit: MSR 0x10000028, val 0x2000000f:0xfdf00100
> > sizeram: _MSR MC_CF07_DATA: 10076112:00004840
> > sizeram: sizem 0x100MB
> > SMMGL0Init: 268304384 bytes
> > SMMGL0Init: offset is 0x80400000
> > SMMGL0Init: MSR 0x10000026, val 0x28fbe080:0x400fffe0
> > writeglmsr: MSR 0x10000080, val 0x00000000:0x00000003
> > writeglmsr: MSR 0x40000020, val 0x20000000:0x000fff80
> > writeglmsr: MSR 0x40000021, val 0x20000000:0x080fffe0
> > writeglmsr: MSR 0x4000002e, val 0x20000000:0x00000003
> > sizeram: _MSR MC_CF07_DATA: 10076112:00004840
> > sizeram: sizem 0x100MB
> > SysmemInit: enable for 256MBytes
> > usable RAM: 268304383 bytes
> > SysmemInit: MSR 0x4000002a, val 0x2000000f:0xfdf00100
> > SMMGL1Init:
> > SMMGL1Init: MSR 0x40000023, val 0x20000080:0x400fffe0
> > writeglmsr: MSR 0x40000080, val 0x00000000:0x00000001
> > writeglmsr: MSR 0x400000e3, val 0x60000000:0x033000f0
> > CPU_RCONF_DEFAULT (1808): 0x25FFFC02:0x10FFDF00
> > CPU_RCONF_BYPASS (180A): 0x00000000 : 0x00000000
> > L2 cache enabled
> > Enabling cache
> > GLPCI R1: system msr.lo 0x00100130 msr.hi 0x0ffdf000
> > GLPCI R2: system msr.lo 0x80400120 msr.hi 0x8041f000
> > Exit northbridge_init_early
> > Done cpubug fixes
> > Not Doing ChipsetFlashSetup()
> > <<<WARNING>>> Graphics init...
> > <<WARNING!!!>>> VRC_VG value: 0xffff
> > Before VSA:
> > do_vsmbios
> > buf ilen 35441 olen60466
> > buf 00060000 *buf 186 buf[256k] 0
> > buf[0x20] signature is b0:10:e6:80
> > Call real_mode_switch_call_vsm
> > biosint: INT# 0x15
> > biosint: eax 0xbea7 ebx 0x4e53 ecx 0x10000026 edx 0x10000028
> > biosint: ebp 0x15ed4 esp 0xff0 edi 0x8a71 esi 0x38
> > biosint: ip 0x5b3 cs 0x6000 flags 0x46
> > biosint: gs 0x0 fs 0x0 ds 0x6000 es 0x0
> > handleint21, eax 0xbea7
> > biosint: INT# 0x15
> > biosint: eax 0xbea4 ebx 0x4e53 ecx 0x10000026 edx 0x10000028
> > biosint: ebp 0x15ed4 esp 0xfee edi 0x8a71 esi 0x38
> > biosint: ip 0x5c1 cs 0x6000 flags 0x46
> > biosint: gs 0x0 fs 0x0 ds 0x6000 es 0x0
> > handleint21, eax 0xbea4
> > do_vsmbios: VSA2 VR signature verified
> > After VSA:
> > <<<WARNING>>> Graphics init...
> > <<WARNING!!!>>> VRC_VG value: 0x2808
> > Finding PCI configuration type.
> > PCI: Using configuration type 1
> > PCI_DOMAIN: 0000 enabled
> > APIC_CLUSTER: 0 enabled
> > PCI: pci_scan_bus for bus 00
> > PCI: 00:01.0 [1022/2080] enabled
> > PCI: 00:01.1 [1022/2081] enabled
> > PCI: 00:01.2 [1022/2082] enabled
> > PCI: 00:0d.0 [10ec/8139] enabled
> > PCI: 00:0f.0 [1022/2090] enabled
> > PCI: 00:0f.2 [1022/209a] enabled
> > PCI: 00: 0f.3 [1022/2093] enabled
> > PCI: 00:0f.4 [1022/2094] enabled
> > PCI: 00:0f.5 [1022/2095] enabled
> > PCI: 00: 0f.6 [1022/2096] enabled
> > PCI: 00:0f.7 [1022/2097] enabled
> > PCI: pci_scan_bus returning with max=000
> > done
> > Allocating resources...
> > Reading resources...
> > Done reading resources.
> > Setting resources...
> > PCI: 00: 01.1 10 <- [0x00fd000000 - 0x00fdffffff] mem
> > PCI: 00:01.1 14 <- [0x00fe000000 - 0x00fe003fff] mem
> > PCI: 00:01.1 18 <- [0x00fe004000 - 0x00fe007fff] mem
> > PCI: 00:01.1 1c <- [0x00fe008000 - 0x00fe00bfff] mem
> > PCI: 00:01.1 20 <- [0x00fe00c000 - 0x00fe00ffff] mem
> > PCI: 00:01.2 10 <- [0x00fe010000 - 0x00fe013fff] mem
> > PCI: 00:0d.0 10 <- [0x0000001000 - 0x00000010ff] io
> > PCI: 00:0d.0 14 <- [0x00fe019000 - 0x00fe0190ff] mem
> > PCI: 00:0f.0 10 <- [0x0000001cb0 - 0x0000001cb7] io
> > PCI: 00:0f.0 14 <- [0x0000001400 - 0x00000014ff] io
> > PCI: 00:0f.0 18 <- [0x0000001c00 - 0x0000001c3f] io
> > PCI: 00:0f.0 1c <- [0x0000001c80 - 0x0000001c9f] io
> > PCI: 00:0f.0 20 <- [0x0000001800 - 0x000000187f] io
> > PCI: 00:0f.0 24 <- [0x0000001c40 - 0x0000001c7f] io
> > PCI: 00:0f.2 20 <- [0x0000001ca0 - 0x0000001caf] io
> > PCI: 00:0f.3 10 <- [0x0000001880 - 0x00000018ff] io
> > PCI: 00:0f.4 10 <- [0x00fe016000 - 0x00fe016fff] mem
> > PCI: 00:0f.5 10 <- [0x00fe017000 - 0x00fe017fff] mem
> > PCI: 00:0f.6 10 <- [0x00fe014000 - 0x00fe015fff] mem
> > PCI: 00:0f.7 10 <- [0x00fe018000 - 0x00fe018fff] mem
> > Done setting resources.
> > Done allocating resources.
> > Enabling resources...
> > PCI: 00:01.0 cmd <- 145
> > PCI: 00:01.1 subsystem <- 00/00
> > PCI: 00:01.1 cmd <- 142
> > PCI: 00:01.2 cmd <- 142
> > PCI: 00: 0d.0 cmd <- 143
> > cs5536: cs5536_pci_dev_enable_resources()
> > PCI: 00:0f.0 cmd <- 149
> > PCI: 00:0f.2 cmd <- 141
> > PCI: 00:0f.3 cmd <- 141
> > PCI: 00:0f.4 cmd <- 142
> > PCI: 00: 0f.5 cmd <- 142
> > PCI: 00: 0f.6 cmd <- 142
> > PCI: 00:0f.7 cmd <- 142
> > done.
> > Initializing devices...
> > Root Device init
> > Norwich ENTER init
> > Norwich EXIT init
> > PCI: 00: 01.0 init
> > PCI: 00:01.1 init
> > APIC_CLUSTER: 0 init
> > Initializing CPU #0
> > CPU: vendor AMD device 5a2
> > CPU: family 05, model 0a, stepping 02
> > model_lx_init
> > Enabling cache
> > A20 (0x92): 2
> > A20 (0x92): 2
> > CPU model_lx_init DONE
> > CPU #0 Initialized
> > PCI: 00:01.2 init
> > PCI: 00: 0d.0 init
> > PCI: 00:0f.0 init
> > cs5536: southbridge_init
> > RTC Init
> > rct_init finished
> > cs5536: southbridge_init: enable_ide_nand_flash is 36
> > Disabling VPCI device: 0x0000106C
> > Disabling VPCI device: 0x00001075
> > Disabling VPCI device: 0x0000107E
> > Disabling VPCI device: 0x00001087
> > Disabling VPCI device: 0x00001090
> > Disabling VPCI device: 0x00001099
> > Disabling VPCI device: 0x000010A2
> > Disabling VPCI device: 0x000010AB
> > PCI: 00:0f.2 init
> > PCI: 00:0f.3 init
> > PCI: 00:0f.4 init
> > PCI: 00:0f.5 init
> > PCI: 00:0f.6 init
> > PCI: 00:0f.7 init
> > Devices initialized
> > Copying IRQ routing tables to 0xf0000...done.
> > Verifing copy of IRQ routing tables at 0xf0000...done
> > Checking IRQ routing table consistency...
> > check_pirq_routing_table() - irq_routing_table located at: 0x000f0000
> > /home/otavio/LinuxBIOSv2/src/arch/i386/boot/pirq_routing.c:
> > 36:check_pirq_routing_table() - checksum is: 0x00 but should be:
> 0xfd
> > done.
> > write_pirq_routing_table(8000785C, BAAA)
> > PIR Entry 0 Dev/Fn: 8 Slot: 0
> > INT: A bitmap: 400 PIRQ: 10
> > INT: B bitmap: 0 PIRQ: 0
> > INT: C bitmap: 0 PIRQ: 0
> > INT: D bitmap: 0 PIRQ: 0
> > Assigning IRQ 10 to 0: 1.1
> > Readback = 10
> > Assigning IRQ 10 to 0:1.2
> > Readback = 10
> > PIR Entry 1 Dev/Fn: 78 Slot: 0
> > INT: A bitmap: 400 PIRQ: 10
> > INT: B bitmap: 400 PIRQ: 10
> > INT: C bitmap: 400 PIRQ: 10
> > INT: D bitmap: 800 PIRQ: 11
> > Assigning IRQ 10 to 0:f.3
> > Readback = 10
> > Assigning IRQ 11 to 0:f.4
> > Readback = 11
> > Assigning IRQ 11 to 0:f.5
> > Readback = 11
> > PIR Entry 2 Dev/Fn: 68 Slot: 1
> > INT: A bitmap: 400 PIRQ: 10
> > INT: B bitmap: 400 PIRQ: 10
> > INT: C bitmap: 800 PIRQ: 11
> > INT: D bitmap: 400 PIRQ: 10
> > Assigning IRQ 10 to 0: d.0
> > Readback = 10
> > PIR Entry 3 Dev/Fn: 70 Slot: 2
> > INT: A bitmap: 400 PIRQ: 10
> > INT: B bitmap: 800 PIRQ: 11
> > INT: C bitmap: 400 PIRQ: 10
> > INT: D bitmap: 400 PIRQ: 10
> > PIR Entry 4 Dev/Fn: 58 Slot: 3
> > INT: A bitmap: 800 PIRQ: 11
> > INT: B bitmap: 400 PIRQ: 10
> > INT: C bitmap: 400 PIRQ: 10
> > INT: D bitmap: 400 PIRQ: 10
> > PIR Entry 5 Dev/Fn: 60 Slot: 4
> > INT: A bitmap: 400 PIRQ: 10
> > INT: B bitmap: 400 PIRQ: 10
> > INT: C bitmap: 400 PIRQ: 10
> > INT: D bitmap: 800 PIRQ: 11
> > Moving GDT to 0x500...ok
> > Adjust low_table_end from 0x00000530 to 0x00001000
> > Adjust rom_table_end from 0x000f0400 to 0x00100000
> > Wrote linuxbios table at: 00000530 - 000006c4 checksum fba9
> >
> > Welcome to elfboot, the open sourced starter.
> > January 2002, Eric Biederman.
> > Version 1.3
> >
> > rom_stream: 0xfff89000 - 0xfffeffff
> > Found ELF candidate at offset 0
> > header_offset is 0
> > Try to load at offset 0x0
> > New segment addr 0x100000 size 0x306e0 offset 0xc0 filesize 0xb248
> > (cleaned up) New segment addr 0x100000 size 0x306e0 offset 0xc0
> filesize
> > 0xb248
> > New segment addr 0x1306e0 size 0x48 offset 0xb320 filesize 0x48
> > (cleaned up) New segment addr 0x1306e0 size 0x48 offset 0xb320
> filesize 0x48
> > Dropping non PT_LOAD segment
> > Dropping non PT_LOAD segment
> > Loading Segment: addr: 0x0000000000100000 memsz: 0x00000000000306e0
> > filesz: 0x000000000000b248
> > Clearing Segment: addr: 0x000000000010b248 memsz: 0x0000000000025498
> > Loading Segment: addr: 0x00000000001306e0 memsz: 0x0000000000000048
> > filesz: 0x0000000000000048
> > Jumping to boot code at 0x108bdc
> > FILO version 0.5 (otavio at labdes15) Wed Jun 20 08:56:24 BRT 2007
> > collect_linuxbios_info: Searching for LinuxBIOS tables...
> > find_lb_table: Found canidate at: 00000530
> > find_lb_table: header checksum o.k.
> > find_lb_table: table checksum o.k.
> > find_lb_table: record count o.k.
> > collect_linuxbios_info: Found LinuxBIOS table at: 00000530
> > convert_memmap: 0x00000000000000 0x00000000001000 16
> > convert_memmap: 0x00000000001000 0x0000000009f000 1
> > convert_memmap: 0x000000000f0000 0x00000000010000 16
> > convert_memmap: 0x00000000100000 0x0000000f6e0000 1
> > Press <Enter> for default boot, or <Esc> for boot prompt... 2 1
> > timed out
> > boot: hda1:/boot/vmlinuz root=/dev/hda1 initrd=/boot/initrd
> > console=tty0 console=ttyS0,115200
> > hda: LBA 40GB: ST340014A
> > Mounted ext2fs
> > Found Linux version 2.6.8-2-386
> (horms at tabatha.lab.ultramonkey.org
> <mailto:horms at tabatha.lab.ultramonkey.org>
> > <mailto:horms at tabatha.lab.ultramonkey.org
> <mailto:horms at tabatha.lab.ultramonkey.org>>) #1 Thu May 19 17:40:50 JST
> > 2005 (protocol 0x203) (loadflags 0x1) bzImage.
> > init_linux_params: Setting up paramters at 0x90000
> > set_memory_size: 0000000000001000 - 00000000000a0000
> > set_memory_size: 0000000000100000 - 000000000f7e0000
> > set_memory_size: ramtop=0xf7e0000
> > set_memory_size: ext_mem_k=64512, alt_mem_k=252800
> > parse_command_line: original command line: "root=/dev/hda1
> > initrd=/boot/initrd console=tty0 console=ttyS0,115200"
> > parse_command_line: kernel command line at 0x91000
> > parse_command_line: initrd=/boot/initrd
> > parse_command_line: kernel command line (48 bytes): "root=/dev/hda1
> > console=tty0 console=ttyS0,115200"
> > load_linux_kernel: offset=0x1600 addr=0x100000 size=0x10a8cb
> > Loading kernel... ok
> > load_initrd: start=0xf391000 end=0xf7af000
> > Loading initrd... ok
> > start_linux: eip=0x100000
> > Jumping to entry point...
> > Linux version 2.6.8-2-386 (horms at tabatha.lab.ultramonkey.org
> <mailto:horms at tabatha.lab.ultramonkey.org>
> > <mailto:horms at tabatha.lab.ultramonkey.org
> <mailto:horms at tabatha.lab.ultramonkey.org>>) (gcc version 3.3.5 (Debian
> > 1:3.3.5-12)) #1 Thu May 19 17:40:50 JST 2005
> >
> > BIOS-provided physical RAM map:
> >
> > BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
> >
> > BIOS-e820: 0000000000100000 - 000000000f7e0000 (usable)
> >
> > 247MB LOWMEM available.
> >
> > DMI not present.
> >
> > ACPI: Unable to locate RSDP
> >
> > Built 1 zonelists
> >
> > Kernel command line: root=/dev/hda1 console=tty0 console=ttyS0,115200
> >
> > No local APIC present or hardware disabled
> >
> > Initializing CPU#0
> >
> > PID hash table entries: 1024 (order 10: 8192 bytes)
> >
> > Detected 431.857 MHz processor.
> >
> > Using tsc for high-res timesource
> >
> > Console: colour dummy device 80x25
> >
> > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
> >
> > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
> >
> > Memory: 244168k/253824k available (1336k kernel code, 8916k reserved,
> > 732k data, 204k init, 0k highmem)
> >
> > Checking if this processor honours the WP bit even in supervisor
> mode...
> > Ok.
> >
> > Calibrating delay loop... 845.82 BogoMIPS
> >
> > Security Scaffold v1.0.0 initialized
> >
> > Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
> >
> > CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
> >
> > CPU: L2 Cache: 128K (32 bytes/line)
> >
> > CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
> >
> > Checking 'hlt' instruction... OK.
> >
> > Checking for popad bug... OK.
> >
> > checking if image is initramfs...it isn't (ungzip failed); looks
> like an
> > initrd
> >
> > Freeing initrd memory: 4216k freed
> >
> > NET: Registered protocol family 16
> >
> > EISA bus registered
> >
> > PCI: Using configuration type 1
> >
> > mtrr: v2.0 (20020519)
> >
> > ACPI: Subsystem revision 20040326
> >
> > ACPI: Interpreter disabled.
> >
> > Linux Plug and Play Support v0.97 (c) Adam Belay
> >
> > PnPBIOS: Scanning system for PnP BIOS support...
> >
> > PnPBIOS: PnP BIOS support was not detected.
> >
> > PCI: Probing PCI hardware
> >
> > PCI: Probing PCI hardware (bus 00)
> >
> > PCI: Using IRQ router default [1022/2090] at 0000:00:0f.0
> >
> > VFS: Disk quotas dquot_6.5.1
> >
> > Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> >
> > devfs: 2004-01-31 Richard Gooch ( rgooch at atnf.csiro.au
> <mailto:rgooch at atnf.csiro.au>
> > <mailto:rgooch at atnf.csiro.au <mailto:rgooch at atnf.csiro.au>>)
> >
> > devfs: boot_options: 0x0
> >
> > Initializing Cryptographic API
> >
> > isapnp: Scanning for PnP cards...
> >
> > isapnp: No Plug & Play device found
> >
> > Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing
> enabled
> >
> > ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> >
> > RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
> >
> > i8042.c : Can't read CTR while initializing i8042.
> >
> > EISA: Probing bus 0 at eisa0
> >
> > Cannot allocate resource for EISA slot 1
> >
> > EISA: Detected 0 cards.
> >
> > NET: Registered protocol family 2
> >
> > IP: routing cache hash table of 2048 buckets, 16Kbytes
> >
> > TCP: Hash tables configured (established 16384 bind 32768)
> >
> > NET: Registered protocol family 8
> >
> > NET: Registered protocol family 20
> >
> > RAMDISK: cramfs filesystem found at block 0
> >
> > RAMDISK: Loading 4216 blocks [1 disk] into ram disk... | / - \ |
> / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
> \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ |
> / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
> \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ |
> / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
> \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ |
> / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / - \ | / -
> \ | / - \ | / - \ | / - \ | / - \ | / - \ done.
> >
> >
> > VFS: Mounted root (cramfs filesystem) readonly.
> >
> > Freeing unused kernel memory: 204k freed
> >
> > vesafb: probe of vesafb0 failed with error -6
> >
> > NET: Registered protocol family 1
> >
> > Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> >
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> idebus=xx
> >
> > hda: ST340014A, ATA DISK drive
> >
> > Using anticipatory io scheduler
> >
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> >
> > hda: max request size: 128KiB
> >
> > hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
> >
> > /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
> >
> >
>
> --
> Marc Jones
> Senior Software Engineer
> (970) 226-9684 Office
> mailto:Marc.Jones at amd.com <mailto:Marc.Jones at amd.com>
> http://www.amd.com/embeddedprocessors
>
>
>
>
>
> --
> Otávio Alcântara
> "I'll never cross to the Dark Side."
>
--
Marc Jones
Senior Software Engineer
(970) 226-9684 Office
mailto:Marc.Jones at amd.com
http://www.amd.com/embeddedprocessors
More information about the coreboot
mailing list