[LinuxBIOS] trying to boot Gigabyte M575SLI

Andreas B. Mundt andi.mundt at web.de
Tue Jun 5 18:04:03 CEST 2007


Hi all,

On Tue, Jun 05, 2007 at 02:25:19PM +0200, Stefan Reinauer wrote:
> 
> Does the same scenario with the same menu.lst work with legacy bios and
> grub?
>  
The setup works fine with linuxbios and Ward's time delay added to filo.c. 

> > > Both are fetched from sda5 when booted, the root filesystem itself
> > > is on sda2 ("linux notation").
> > 
> > And even if it does, symlinks across partitions are not likely to be
> > supported.
>  
> yes. they are definitely not.
> 
I should clearify that: it's not a "symlink across partitions", just the
root file system is on that other partition, like a separated boot/root 
partition setup.
>
> > Try specifying hde5:.. paths for both the kernel and initrd directly
> > to FILO, bypassing the menu.lst file, or possibly doing so within the
> > menu.lst file.
> 
I did this now and got a bit further. The Kernel seems to be loaded fine
(I kept the symlinks so far), but it fails to mount the root partition. Perhaps it 
has to be specified also in filo notation or the initrd.img is not loaded and 
needed to mount the ext3 root partion ...

I'm going to investigate that....

Thanks,

	Andi 
  



LinuxBIOS-2.0.0_m57sli_Fallback Sun Jun  3 18:19:58 CEST 2007 starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started: 
started ap apicid:  01
SBLink=00
NC node|link=00
begin msr fid, vid 3107121207110202
set fid failed for apicid =00
end   msr fid, vid 3107120707110210
mcp55_num:01
ht reset -


LinuxBIOS-2.0.0_m57sli_Fallback Sun Jun  3 18:19:58 CEST 2007 starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
core0 started: 
started ap apicid:  01
SBLink=00
NC node|link=00
begin msr fid, vid 3107120707110210
set fid failed for apicid =00
end   msr fid, vid 3107120707110210
mcp55_num:01
Ram1.00
Ram2.00
Unbuffered
333Mhz
Interleaved
RAM: 0x00400000 KB
Ram3
	dimm_mask = 00000033
	x4_mask = 00000000
	x16_mask = 00000000
	single_rank_mask = 00000000
	ODC = 00111322
	Addr Timing= 002b2220
Initializing memory:  done
RAM: 0x00500000 KB
Setting variable MTRR 2, base:    0MB, range: 2048MB, type WB
Setting variable MTRR 3, base: 2048MB, range: 1024MB, type WB
set DQS timing:RcvrEn:Pass1: 00 CTLRMaxDelay=14 done
set DQS timing:DQSPos: 00 done
set DQS timing:RcvrEn:Pass2: 00 CTLRMaxDelay=34 done
Total DQS Training : tsc [00]=0000000045996bea
Total DQS Training : tsc [01]=00000000475a61d8
Total DQS Training : tsc [02]=000000009ff4ca11
Total DQS Training : tsc [03]=00000000a23a37b8
Ram4
v_esp=000cee78
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now 
Clearing initial memory region: Done
Copying LinuxBIOS to RAM.
src=fffdf000
dst=00100000
linxbios_ram.nrv2b length = 0000d633
linxbios_ram.bin   length = 00022510
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0_m57sli_Fallback Tue Jun  5 17:34:18 CEST 2007 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
  PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:00.0 [10de/0369] enabled next_unitid: 0010
PCI: pci_scan_bus for bus 00
PCI: 00:00.0 [10de/0369] enabled
PCI: 00:01.0 [10de/0360] enabled
PCI: 00:01.1 [10de/0368] enabled
PCI: 00:01.2 [10de/036a] enabled
PCI: 00:01.3 [10de/036b] enabled
PCI: 00:02.0 [10de/036c] enabled
PCI: 00:02.1 [10de/036d] enabled
PCI: 00:04.0 [10de/036e] enabled
PCI: 00:05.0 [10de/037f] enabled
PCI: 00:05.1 [10de/037f] enabled
PCI: 00:05.2 [10de/037f] enabled
PCI: 00:06.0 [10de/0370] enabled
PCI: 00:06.1 [10de/0371] enabled
PCI: 00:08.0 [10de/0373] enabled
PCI: 00:0a.0 [10de/0376] enabled
PCI: 00:0b.0 [10de/0374] enabled
PCI: 00:0c.0 [10de/0374] enabled
PCI: 00:0d.0 [10de/0378] enabled
PCI: 00:0e.0 [10de/0375] enabled
PCI: 00:0f.0 [10de/0377] enabled
PNP: 002e.0 disabled
PNP: 002e.1 enabled
PNP: 002e.2 disabled
PNP: 002e.3 disabled
PNP: 002e.4 enabled
PNP: 002e.5 enabled
PNP: 002e.6 enabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
smbus: PCI: 00:01.1[0]->I2C: 01:50 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:51 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:52 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:53 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:54 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:55 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:56 enabled
smbus: PCI: 00:01.1[0]->I2C: 01:57 enabled
smbus: PCI: 00:01.1[1]->I2C: 02:51 enabled
PCI: pci_scan_bus for bus 01
PCI: pci_scan_bus returning with max=001
PCI: pci_scan_bus for bus 02
PCI: pci_scan_bus returning with max=002
PCI: pci_scan_bus for bus 03
PCI: pci_scan_bus returning with max=003
PCI: pci_scan_bus for bus 04
PCI: pci_scan_bus returning with max=004
PCI: pci_scan_bus for bus 05
PCI: pci_scan_bus returning with max=005
PCI: pci_scan_bus for bus 06
PCI: pci_scan_bus returning with max=006
PCI: pci_scan_bus for bus 07
PCI: 07:00.0 [10de/0392] enabled
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
PCI: pci_scan_bus returning with max=007
done
Allocating resources...
Reading resources...
PCI: 00:06.0 1c <- [0x000000f000 - 0x000000efff] bus 01 io
PCI: 00:06.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 01 prefmem
PCI: 00:06.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 01 mem
PCI: 00:0a.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 02 io
PCI: 00:0a.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 02 prefmem
PCI: 00:0a.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 02 mem
PCI: 00:0b.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 03 io
PCI: 00:0b.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 03 prefmem
PCI: 00:0b.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 03 mem
PCI: 00:0c.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 04 io
PCI: 00:0c.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 04 prefmem
PCI: 00:0c.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 04 mem
PCI: 00:0d.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 05 io
PCI: 00:0d.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 05 prefmem
PCI: 00:0d.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 05 mem
PCI: 00:0e.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 06 io
PCI: 00:0e.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 06 prefmem
PCI: 00:0e.0 20 <- [0x00fff00000 - 0x00ffefffff] bus 06 mem
Done reading resources.
Allocating VGA resource PCI: 07:00.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:0f.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0
Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000
Setting PCI_BRIDGE_CTL_VGA for bridge Root Device
Setting resources...
VGA: PCI: 00:18.0 (aka node 0) link 0 has VGA device
PCI: 00:18.0 1c0 <- [0x0000001000 - 0x0000003fff] io <node 0 link 0>
PCI: 00:18.0 1b8 <- [0x00e0000000 - 0x00efffffff] prefmem <node 0 link 0>
PCI: 00:18.0 1b0 <- [0x00f4000000 - 0x00f61fffff] mem <node 0 link 0>
PCI: 00:01.0 14 <- [0x00f6144000 - 0x00f6144fff] mem
PNP: 002e.1 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.1 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.4 60 <- [0x0000000290 - 0x0000000297] io
PNP: 002e.4 62 <- [0x0000000230 - 0x0000000237] io
PNP: 002e.4 70 <- [0x0000000009 - 0x0000000009] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.6 70 <- [0x000000000c - 0x000000000c] irq
PCI: 00:01.1 10 <- [0x0000002c00 - 0x0000002c3f] io
PCI: 00:01.1 20 <- [0x0000002c40 - 0x0000002c7f] io
PCI: 00:01.1 24 <- [0x0000002c80 - 0x0000002cbf] io
PCI: 00:01.1 60 <- [0x0000002000 - 0x00000020ff] io
PCI: 00:01.1 64 <- [0x0000002400 - 0x00000024ff] io
PCI: 00:01.1 68 <- [0x0000002800 - 0x00000028ff] io
PCI: 00:01.3 10 <- [0x00f6100000 - 0x00f613ffff] mem
PCI: 00:02.0 10 <- [0x00f6145000 - 0x00f6145fff] mem
PCI: 00:02.1 10 <- [0x00f614a000 - 0x00f614a0ff] mem
PCI: 00:04.0 20 <- [0x0000002cc0 - 0x0000002ccf] io
PCI: 00:05.0 10 <- [0x0000003000 - 0x0000003007] io
PCI: 00:05.0 14 <- [0x0000003070 - 0x0000003073] io
PCI: 00:05.0 18 <- [0x0000003010 - 0x0000003017] io
PCI: 00:05.0 1c <- [0x0000003080 - 0x0000003083] io
PCI: 00:05.0 20 <- [0x0000002cd0 - 0x0000002cdf] io
PCI: 00:05.0 24 <- [0x00f6146000 - 0x00f6146fff] mem
PCI: 00:05.1 10 <- [0x0000003020 - 0x0000003027] io
PCI: 00:05.1 14 <- [0x0000003090 - 0x0000003093] io
PCI: 00:05.1 18 <- [0x0000003030 - 0x0000003037] io
PCI: 00:05.1 1c <- [0x00000030a0 - 0x00000030a3] io
PCI: 00:05.1 20 <- [0x0000002ce0 - 0x0000002cef] io
PCI: 00:05.1 24 <- [0x00f6147000 - 0x00f6147fff] mem
PCI: 00:05.2 10 <- [0x0000003040 - 0x0000003047] io
PCI: 00:05.2 14 <- [0x00000030b0 - 0x00000030b3] io
PCI: 00:05.2 18 <- [0x0000003050 - 0x0000003057] io
PCI: 00:05.2 1c <- [0x00000030c0 - 0x00000030c3] io
PCI: 00:05.2 20 <- [0x0000002cf0 - 0x0000002cff] io
PCI: 00:05.2 24 <- [0x00f6148000 - 0x00f6148fff] mem
PCI: 00:06.1 10 <- [0x00f6140000 - 0x00f6143fff] mem
PCI: 00:08.0 10 <- [0x00f6149000 - 0x00f6149fff] mem
PCI: 00:08.0 14 <- [0x0000003060 - 0x0000003067] io
PCI: 00:08.0 18 <- [0x00f614b000 - 0x00f614b0ff] mem
PCI: 00:08.0 1c <- [0x00f614c000 - 0x00f614c00f] mem
PCI: 00:0f.0 1c <- [0x0000001000 - 0x0000001fff] bus 07 io
PCI: 00:0f.0 24 <- [0x00e0000000 - 0x00efffffff] bus 07 prefmem
PCI: 00:0f.0 20 <- [0x00f4000000 - 0x00f60fffff] bus 07 mem
PCI: 07:00.0 10 <- [0x00f4000000 - 0x00f4ffffff] mem
PCI: 07:00.0 14 <- [0x00e0000000 - 0x00efffffff] prefmem64
PCI: 07:00.0 1c <- [0x00f5000000 - 0x00f5ffffff] mem64
PCI: 07:00.0 24 <- [0x0000001000 - 0x000000107f] io
PCI: 07:00.0 30 <- [0x00f6000000 - 0x00f601ffff] romem
PCI: 00:18.3 94 <- [0x00f0000000 - 0x00f3ffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resources...
PCI: 00:18.0 cmd <- 140
PCI: 00:00.0 subsystem <- 1022/2b80
PCI: 00:00.0 cmd <- 146
PCI: 00:01.0 subsystem <- 1022/2b80
PCI: 00:01.0 cmd <- 14f
mcp55 lpc decode:PNP: 002e.1, base=0x000003f8, end=0x000003ff
mcp55 lpc decode:PNP: 002e.4, base=0x00000290, end=0x00000297
mcp55 lpc decode:PNP: 002e.4, base=0x00000230, end=0x00000237
mcp55 lpc decode:PNP: 002e.5, base=0x00000060, end=0x00000060
mcp55 lpc decode:PNP: 002e.5, base=0x00000064, end=0x00000064
PCI: 00:01.1 subsystem <- 1022/2b80
PCI: 00:01.1 cmd <- 141
PCI: 00:01.2 cmd <- 540
PCI: 00:01.3 cmd <- 142
PCI: 00:02.0 subsystem <- 1022/2b80
PCI: 00:02.0 cmd <- 142
PCI: 00:02.1 subsystem <- 1022/2b80
PCI: 00:02.1 cmd <- 142
PCI: 00:04.0 subsystem <- 1022/2b80
PCI: 00:04.0 cmd <- 141
PCI: 00:05.0 subsystem <- 1022/2b80
PCI: 00:05.0 cmd <- 143
PCI: 00:05.1 subsystem <- 1022/2b80
PCI: 00:05.1 cmd <- 143
PCI: 00:05.2 subsystem <- 1022/2b80
PCI: 00:05.2 cmd <- 143
PCI: 00:06.0 bridge ctrl <- 0a03
PCI: 00:06.0 cmd <- 144
PCI: 00:06.1 subsystem <- 1022/2b80
PCI: 00:06.1 cmd <- 142
PCI: 00:08.0 subsystem <- 1022/2b80
PCI: 00:08.0 cmd <- 143
PCI: 00:0a.0 bridge ctrl <- 0003
PCI: 00:0a.0 cmd <- 140
PCI: 00:0b.0 bridge ctrl <- 0003
PCI: 00:0b.0 cmd <- 140
PCI: 00:0c.0 bridge ctrl <- 0003
PCI: 00:0c.0 cmd <- 140
PCI: 00:0d.0 bridge ctrl <- 0003
PCI: 00:0d.0 cmd <- 140
PCI: 00:0e.0 bridge ctrl <- 0003
PCI: 00:0e.0 cmd <- 140
PCI: 00:0f.0 bridge ctrl <- 000b
PCI: 00:0f.0 cmd <- 147
PCI: 07:00.0 cmd <- 143
PCI: 00:18.1 subsystem <- 1022/2b80
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 1022/2b80
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
start_eip=0x00006000, offset=0x00110000, code_size=0x0000005b
Initializing CPU #0
CPU: vendor AMD device 60fb1
CPU: family 0f, model 6b, stepping 01
Enabling cache

Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base:    0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
Setting up local apic... apic_id: 0x00 done.
ECC Disabled
CPU #0 Initialized
Initializing CPU #1
Waiting for 1 CPUS to stop
CPU: vendor AMD device 60fb1
CPU: family 0f, model 6b, stepping 01
Enabling cache

Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base:    0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's

MTRR check
Fixed MTRRs   : Enabled
Variable MTRRs: Enabled

CPU model AMD Athlon(tm) 64 X2 Dual Core Processor 4800+
Setting up local apic... apic_id: 0x01 done.
CPU #1 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 00:01.0 init
set power on after power fail
RTC Init
Invalid CMOS LB checksum
PNP: 002e.1 init
PNP: 002e.4 init
FAN_CTL: reg = 0x02a9, read value = 0x50
FAN_CTL: reg = 0x02a9, writing value = 0xd7
PNP: 002e.5 init
PNP: 002e.6 init
PCI: 00:01.1 init
PCI: 00:02.1 init
PCI: 00:04.0 init
IDE0
PCI: 00:05.0 init
SATA S 	SATA P 
PCI: 00:05.1 init
SATA S 	SATA P 
PCI: 00:05.2 init
SATA S 	SATA P 
PCI: 00:06.0 init
dev_root mem base = 0x00e0000000
[0x50] <-- 0xe0000000
PCI: 00:06.1 init
base = f6140000
codec_mask = 01
codec viddid: 10ec0883
No verb!
PCI: 00:08.0 init
MCP55 MAC PHY ID 0x01410c00 PHY ADDR 1
PCI: 00:0a.0 init
PCI: 00:0b.0 init
PCI: 00:0c.0 init
PCI: 00:0d.0 init
PCI: 00:0e.0 init
PCI: 00:0f.0 init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 00:01.2 init
PCI: 00:01.3 init
PCI: 07:00.0 init
rom address for PCI: 07:00.0 = f6000000
copying VGA ROM Image from 0xf6000000 to 0xc0000, 0xf600 bytes
entering emulator
halt_sys: file /home/andi/freeBIOS/LinuxBIOSv2/src/devices/emulator/x86emu/ops.c, line 4387
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 00000274
Moving GDT to 0x500...ok
Adjust low_table_end from 0x00000530 to 0x00001000 
Adjust rom_table_end from 0x000f0400 to 0x00100000 
Wrote linuxbios table at: 00000530 - 00000dd4  checksum 611c

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

rom_stream: 0xfffc0000 - 0xfffdefff
Found ELF candidate at offset 0
header_offset is 0
Try to load at offset 0x0
New segment addr 0x100000 size 0x31220 offset 0xc0 filesize 0xbd88
(cleaned up) New segment addr 0x100000 size 0x31220 offset 0xc0 filesize 0xbd88
New segment addr 0x131220 size 0x48 offset 0xbe60 filesize 0x48
(cleaned up) New segment addr 0x131220 size 0x48 offset 0xbe60 filesize 0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x00000000bff80000 memsz: 0x0000000000031220 filesz: 0x000000000000bd88
Clearing Segment: addr: 0x00000000bff8bd88 memsz: 0x0000000000025498
Loading Segment: addr: 0x00000000bffb1220 memsz: 0x0000000000000048 filesz: 0x0000000000000048
Jumping to boot code at 0x109618
FILO version 0.5 (andi at flashgordon) Tue Jun  5 17:33:50 CEST 2007
setup_timers: CPU 2400 MHz
Press <Enter> for default boot, or <Esc> for boot prompt... 2 1 timed out
boot: hde5:/vmlinuz hde5:/initrd.img root=/dev/sda2 ro console=ttyS0,115200
find_ide_controller: found PCI IDE controller 10de:037f prog_if=0x85
find_ide_controller: primary channel: native PCI mode
find_ide_controller: cmd_base=0x3000 ctrl_base=0x3070
ide_software_reset: Waiting for ide2 to become ready for reset... ok
init_drive: Testing for hde
init_drive: Probing for hde
init_drive: LBA mode, sectors=268435455
init_drive: LBA48 mode, sectors=488395055
init_drive: Init device params... ok
hde: LBA48 250GB: SAMSUNG SP2504C                         
init_drive: Testing for hdf
init_drive: Probing for hdf
IDE timeout after 50 ms while waiting for drq()
pio_data_in: No DRQ from device after read command
print_status: IDE: status=0x0, err=0x0
init_drive: Testing for hdf
init_drive: Probing for hdf
IDE timeout after 50 ms while waiting for drq()
pio_data_in: No DRQ from device after read command
print_status: IDE: status=0x0, err=0x0
ide_readmany: sector 0 to 0x0010c020
ide_readmany: sector 132825420 to 0x0010d820
ide_readmany: sector 132825485 to 0x0010da20
ide_readmany: sector 132825486 to 0x0010dc20
Mounted ext2fs
ide_readmany: sector 132825491 to 0x0010e620
ide_readmany: sector 132825492 to 0x0010e820
ide_readmany: sector 132825493 to 0x0010ea20
ide_readmany: sector 132825494 to 0x0010ec20
ide_readmany: sector 132825495 to 0x0010ee20
ide_readmany: sector 132825496 to 0x0010f020
ide_readmany: sector 132825497 to 0x0010f220
ide_readmany: sector 132825498 to 0x0010f420
ide_readmany: sector 132825515 to 0x00111620
ide_readmany: sector 132825516 to 0x00111820
ide_readmany: sector 132825517 to 0x00111a20
ide_readmany: sector 132825518 to 0x00111c20
ide_readmany: sector 132825519 to 0x00111e20
ide_readmany: sector 132825520 to 0x00112020
ide_readmany: sector 132825521 to 0x00112220
ide_readmany: sector 132825522 to 0x00112420
ide_readmany: sector 132829571 to 0x0010c620
ide_readmany: sector 132829572 to 0x0010c820
ide_readmany: sector 132829573 to 0x0010ca20
ide_readmany: sector 132829574 to 0x0010cc20
ide_readmany: sector 132829575 to 0x0010ce20
ide_readmany: sector 132829576 to 0x0010d020
ide_readmany: sector 132829577 to 0x0010d220
ide_readmany: sector 132829578 to 0x0010d420
ide_readmany: sector 136233387 to 0x00111620
ide_readmany: sector 136233388 to 0x00111820
ide_readmany: sector 136233389 to 0x00111a20
ide_readmany: sector 136233390 to 0x00111c20
ide_readmany: sector 136233391 to 0x00111e20
ide_readmany: sector 136233392 to 0x00112020
ide_readmany: sector 136233393 to 0x00112220
ide_readmany: sector 136233394 to 0x00112420
ide_readmany: sector 136298891 to 0x0010d620
ide_readmany: sector 136298892 to 0x0010d820
ide_readmany: sector 136298893 to 0x0010da20
ide_readmany: sector 136298894 to 0x0010dc20
ide_readmany: sector 136298895 to 0x0010de20
ide_readmany: sector 136298896 to 0x0010e020
ide_readmany: sector 136298897 to 0x0010e220
ide_readmany: sector 136298898 to 0x0010e420
ext2fs_read_one: block  452608  offset=0 len=52 ret=0
ide_readmany: sector 136446347 to 0x0010d620
ide_readmany: sector 132825515 to 0x00111620
ide_readmany: sector 132825516 to 0x00111820
ide_readmany: sector 132825517 to 0x00111a20
ide_readmany: sector 132825518 to 0x00111c20
ide_readmany: sector 132825519 to 0x00111e20
ide_readmany: sector 132825520 to 0x00112020
ide_readmany: sector 132825521 to 0x00112220
ide_readmany: sector 132825522 to 0x00112420
ide_readmany: sector 136233387 to 0x00111620
ide_readmany: sector 136233388 to 0x00111820
ide_readmany: sector 136233389 to 0x00111a20
ide_readmany: sector 136233390 to 0x00111c20
ide_readmany: sector 136233391 to 0x00111e20
ide_readmany: sector 136233392 to 0x00112020
ide_readmany: sector 136233393 to 0x00112220
ide_readmany: sector 136233394 to 0x00112420
ide_readmany: sector 136298891 to 0x0010d620
ext2fs_read_one: block  452608  offset=0 len=560 ret=0
ide_readmany: sector 136446347 to 0x0010d620
ide_readmany: sector 136446348 to 0x0010d820
Found Linuxblock  452609  offset=1099 len=256 ret=0
ide_readmany: sector 136446357 to 0x0010ea20
 version 2.6.21-1-amd64 (unknown at Debian) #1 SMP Fri May 18 23:28:21 CEST 2007 bzImage.
Loading kernel... sector 136446443 to 0x00111620
ide_readmany: sector 136446444 to 0x00111820
ide_readmany: sector 136446445 to 0x00111a20
ide_readmany: sector 136446446 to 0x00111c20
ide_readmany: sector 136446447 to 0x00111e20
ide_readmany: sector 136446448 to 0x00112020
ide_readmany: sector 136446449 to 0x00112220
ide_readmany: sector 136446450 to 0x00112420
ext2fs_read_many:  10 blocks  452610 - 452619  len=1561450 ret=0
ide_readmany: sectors 136446363 - 136446442 ( 80) to 0x40231270
ext2fs_read_many: 372 blocks  452621 - 452992  len=1520490 ret=40960
ide_readmany: sectors 136446451 - 136446706 (256) to 0x4023b270
ide_readmany: sectors 136446707 - 136446962 (256) to 0x4025b270
ide_readmany: sectors 136446963 - 136447218 (256) to 0x4027b270
ide_readmany: sectors 136447219 - 136447474 (256) to 0x4029b270
ide_readmany: sectors 136447475 - 136447730 (256) to 0x402bb270
ide_readmany: sectors 136447731 - 136447986 (256) to 0x402db270
ide_readmany: sectors 136447987 - 136448242 (256) to 0x402fb270
ide_readmany: sectors 136448243 - 136448498 (256) to 0x4031b270
ide_readmany: sectors 136448499 - 136448754 (256) to 0x4033b270
ide_readmany: sectors 136448755 - 136449010 (256) to 0x4035b270
ide_readmany: sectors 136449011 - 136449266 (256) to 0x4037b270
ide_readmany: sectors 136449267 - 136449426 (160) to 0x4039b270
ext2fs_read: discarding 3222 surplus bytes
ext2fs_read: done reading many  len=0 ret=1561450
ok
Jumping to entry point...
Linux version 2.6.21-1-amd64 (Debian 2.6.21-2) (waldi at debian.org) (gcc version 4.1.3 20070514 (prerelease) (Debian 4.1.2-7)) #1 SMP Fri May 18 23:28:21 CEST 2007
Command line: hde5:/initrd.img root=/dev/sda2 ro console=ttyS0,115200
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000001000 - 00000000000a0000 (usable)
 BIOS-e820: 00000000000c0000 - 00000000000f0000 (usable)
 BIOS-e820: 0000000000100000 - 00000000c0000000 (usable)
 BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
end_pfn_map = 1310720
DMI not present or invalid.
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 0000000140000000
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-0000000140000000
Zone PFN ranges:
  DMA             1 ->     4096
  DMA32        4096 ->  1048576
  Normal    1048576 ->  1310720
early_node_map[4] active PFN ranges
    0:        1 ->      160
    0:      192 ->      240
    0:      256 ->   786432
    0:  1048576 ->  1310720
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
Intel MultiProcessor Specification v1.4
MPTABLE: OEM ID: GIGABYTE MPTABLE: Product ID: M57SLI       MPTABLE: APIC at: 0xFEE00000
Processor #0 (Bootup-CPU)
Processor #1
I/O APIC #2 at 0xF6144000.
Setting APIC routing to physical flat
Processors: 2
Nosave address range: 00000000000a0000 - 00000000000c0000
Nosave address range: 00000000000f0000 - 0000000000100000
Nosave address range: 00000000c0000000 - 0000000100000000
Allocating PCI resources starting at c4000000 (gap: c0000000:40000000)
SMP: Allowing 2 CPUs, 0 hotplug CPUs
PERCPU: Allocating 37504 bytes of per cpu data
Built 1 zonelists.  Total pages: 1029631
Kernel command line: hde5:/initrd.img root=/dev/sda2 ro console=ttyS0,115200
Unknown boot option `hde5:/initrd.img': ignoring
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
time.c: Detected 2400.010 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ f0000000 size 64 MB
Memory: 4112116k/5242880k available (1975k kernel code, 81992k reserved, 931k data, 296k init)
Calibrating delay using timer specific routine.. 4803.83 BogoMIPS (lpj=9607665)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20070126
ACPI Exception (tbxface-0618): AE_NO_ACPI_TABLES, While loading namespace from ACPI tables [20070126]
ACPI: Unable to load the System Description Tables
Using local APIC timer interrupts.
result 12500063
Detected 12.500 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 4800.26 BogoMIPS (lpj=9600531)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4800+ stepping 01
Brought up 2 CPUs
migration_cost=205
NET: Registered protocol family 16
PCI: Using configuration type 1
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Probing PCI hardware
PCI: Using IRQ router default [10de/0370] at 0000:00:06.0
PCI->APIC IRQ transform: 0000:00:01.1[A] -> IRQ 10
PCI->APIC IRQ transform: 0000:00:01.3[B] -> IRQ 10
PCI->APIC IRQ transform: 0000:00:02.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:00:02.1[B] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:05.0[A] -> IRQ 20
PCI->APIC IRQ transform: 0000:00:05.1[B] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:05.2[C] -> IRQ 21
PCI->APIC IRQ transform: 0000:00:06.1[B] -> IRQ 23
PCI->APIC IRQ transform: 0000:00:08.0[A] -> IRQ 22
PCI->APIC IRQ transform: 0000:07:00.0[A] -> IRQ 17
NET: Registered protocol family 8
NET: Registered protocol family 20
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ f0000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0a.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0b.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:0f.0
  IO window: 1000-1fff
  MEM window: f4000000-f60fffff
  PREFETCH window: e0000000-efffffff
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1181058107.360:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
assign_interrupt_mode Found MSI capability
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFS: Cannot open root device "sda2" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)




More information about the coreboot mailing list