[LinuxBIOS] tyan s2881 - partial success (update)
Ward Vandewege
ward at gnu.org
Wed Jan 4 00:38:32 CET 2006
Back from the holidays; hope you all enjoyed yours :)
I've been trying a couple more things to get beyond the linuxbios problems
I'm seeing. I've now compiled everything with Gcc 3.4.5, and that did not
solve the problem (previously I had compiled etherboot with Gcc 4/linuxbios
with 3.4.5).
I've also updated to the latest SVN tree (2148) - no changes there it seems
except for a few in the flashrom directory.
I'm attaching a new serial output which shows linuxbios just giving up
(resetting?) near the end of the boot sequence (right after the software raid
array is loaded, which immediately starts syncing; it is still dirty).
Compare with the serial log below that I added to my previous message; there
it got slightly further in the boot sequence than this time.
I'm intrigued by how LinuxBIOS seems to reset itself at the start of the boot
as well; is this normal? It doesn't do it always, I tried several times, and
sometimes it does, sometimes it doesn't.
Debugging suggestions welcome :)
Thanks,
Ward.
On Thu, Dec 15, 2005 at 11:30:22PM -0500, Ward Vandewege wrote:
> So, with some help from Yinghai today, I finally managed to make my own
> working LinuxBIOS image, and boot it on the s2881. Fantastic!
>
> It cut boot time roughly in half - and that's without doing any optimizing of
> the init startup sequence, which now takes up the bulk of the bootup time.
>
> Anyway. Once the system booted, I tested network access and a few other
> things, and everything seemed to work just fine.
>
> But 10 minutes later the machine was no longer pingable, and I didn't get any
> response on the serial console anymore either.
>
> I shut it down, and restarted with LinuxBIOS. At this point, it would not
> boot anymore - as you can see in the attached serial log, it just decides to
> restart its fallback image just after init starts, which then hangs the box.
>
> Any clues? This is the latest svn revision (2145), with Etherboot 5.4.1 +
> FILO to boot from the local SATA drive.
>
> I rebooted with the proprietary BIOS, which brought the box up just fine
> (after complaining that it had to reset the CMOS). It started re-syncing the
> software RAID array right after boot though, so maybe that is related to the
> linuxBIOS hang upon boot, which is right after the kernel starts the RAID
> devices?
>
> I won't be able to work more on the box for the next week or two
> (holidays...), but I thought I'd better signal this now.
>
> Thanks,
> Ward.
>
> --
> Ward Vandewege <ward at fsf.org>
> Free Software Foundation - Senior System Administrator
>
>
> LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
> (0,1) link=00
> (1,0) link=00
> 02 nodes initialized.
> core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
> SBLink=02
> NC node|link=02
> ht reset -
>
>
> LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
> (0,1) link=00
> (1,0) link=00
> 02 nodes initialized.
> core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
> SBLink=02
> NC node|link=02
> Ram1.00
> Ram1.01
> Ram2.00
> Ram2.01
> Ram3
> Initializing memory: done
> Initializing memory: done
> Ram4
> v_esp=000cfd40
> cpu_reset = 00000000
> Clearing initial memory region: No cache as ram now - Use Ram as Stack now - done
> new_cpu_reset = 00000000
> Copying LinuxBIOS to ram.
> src=fffe0004
> dst=00004000
> linxbios_ram.bin length = 0001928c
> Jumping to LinuxBIOS.
> LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 booting...
> Enumerating buses...
> APIC_CLUSTER: 0 enabled
> PCI_DOMAIN: 0000 enabled
> PCI: 00:18.3 siblings=1
> CPU: APIC: 00 enabled
> CPU: APIC: 01 enabled
> PCI: 00:19.0 [1022/1100] enabled
> PCI: 00:19.1 [1022/1101] enabled
> PCI: 00:19.2 [1022/1102] enabled
> PCI: 00:19.3 [1022/1103] enabled
> PCI: 00:19.3 siblings=1
> CPU: APIC: 02 enabled
> CPU: APIC: 03 enabled
> PCI: pci_scan_bus for bus 0
> PCI: 00:18.0 [1022/1100] enabled
> PCI: 00:18.1 [1022/1101] enabled
> PCI: 00:18.2 [1022/1102] enabled
> PCI: 00:18.3 [1022/1103] enabled
> PCI: 00:19.0 [1022/1100] enabled
> PCI: 00:19.1 [1022/1101] enabled
> PCI: 00:19.2 [1022/1102] enabled
> PCI: 00:19.3 [1022/1103] enabled
> PCI: 01:00.0 [1022/7450] enabled
> PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003
> PCI: 01:00.0 [1022/7460] enabled
> PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007
> PCI: pci_scan_bus for bus 1
> PCI: 01:01.0 [1022/7450] enabled
> PCI: 01:01.1 [1022/7451] enabled
> PCI: 01:02.0 [1022/7450] enabled
> PCI: 01:02.1 [1022/7451] enabled
> PCI: 01:03.0 [1022/7460] enabled
> PCI: 01:04.0 [1022/7468] enabled
> PCI: 01:04.1 [1022/7469] enabled
> PCI: 01:04.2 [1022/746a] enabled
> PCI: 01:04.3 [1022/746b] enabled
> PCI: pci_scan_bus for bus 2
> PCI: 02:09.0 [14e4/1648] enabled
> PCI: 02:09.1 [14e4/1648] enabled
> Disabling static device: PCI: 02:0a.0
> Disabling static device: PCI: 02:0a.1
> PCI: pci_scan_bus returning with max=02
> PCI: 02: 100MHz PCI-X
> PCI: pci_scan_bus for bus 3
> PCI: pci_scan_bus returning with max=03
> PCI: 03: 133MHz PCI-X
> PCI: pci_scan_bus for bus 4
> PCI: 04:00.0 [1022/7464] enabled
> PCI: 04:00.1 [1022/7464] enabled
> PCI: 04:05.0 [1095/3114] enabled
> PCI: 04:06.0 [1002/4752] enabled
> PCI: pci_scan_bus returning with max=04
> PNP: 002e.0 enabled
> PNP: 002e.1 disabled
> PNP: 002e.2 enabled
> PNP: 002e.3 disabled
> PNP: 002e.5 enabled
> PNP: 002e.6 disabled
> PNP: 002e.7 disabled
> PNP: 002e.8 disabled
> PNP: 002e.9 disabled
> PNP: 002e.a disabled
> PNP: 002e.b enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:50 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:51 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:52 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:53 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:54 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:55 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:56 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:57 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:2d enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:2a enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:49 enabled
> smbus: PCI: 01:04.3[0]->I2C: 01:4a enabled
> PCI: pci_scan_bus returning with max=04
> PCI: pci_scan_bus returning with max=04
> done
> Allocating resources...
> Reading resources...
> PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io
> PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem
> PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem
> Done reading resources.
> Setting resources...
> PCI: 00:18.0 1ba <- [0x00fd300000 - 0x00fd2fffff] prefmem <node 0 link 2>
> PCI: 00:18.0 1c2 <- [0x0000001000 - 0x0000002fff] io <node 0 link 2>
> PCI: 00:18.0 1b2 <- [0x00fc000000 - 0x00fd2fffff] mem <node 0 link 2>
> PCI: 01:01.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 2 mem
> PCI: 02:09.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem64
> PCI: 02:09.0 18 <- [0x00fd110000 - 0x00fd11ffff] mem64
> PCI: 02:09.1 10 <- [0x00fd120000 - 0x00fd12ffff] mem64
> PCI: 02:09.1 18 <- [0x00fd130000 - 0x00fd13ffff] mem64
> PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem64
> PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem64
> PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io
> PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem
> PCI: 04:00.0 10 <- [0x00fd000000 - 0x00fd000fff] mem
> PCI: 04:00.1 10 <- [0x00fd001000 - 0x00fd001fff] mem
> PCI: 04:05.0 10 <- [0x0000001410 - 0x0000001417] io
> PCI: 04:05.0 14 <- [0x0000001430 - 0x0000001433] io
> PCI: 04:05.0 18 <- [0x0000001420 - 0x0000001427] io
> PCI: 04:05.0 1c <- [0x0000001440 - 0x0000001443] io
> PCI: 04:05.0 20 <- [0x0000001400 - 0x000000140f] io
> PCI: 04:05.0 24 <- [0x00fd003000 - 0x00fd0033ff] mem
> PCI: 04:06.0 10 <- [0x00fc000000 - 0x00fcffffff] mem
> PCI: 04:06.0 14 <- [0x0000001000 - 0x00000010ff] io
> PCI: 04:06.0 18 <- [0x00fd002000 - 0x00fd002fff] mem
> PCI: 04:06.0 30 <- [0x00fff80000 - 0x00fff9ffff] romem
> PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] io
> PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq
> PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq
> PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
> PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq
> PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
> PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
> PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
> PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq
> PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io
> PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq
> PCI: 01:04.1 20 <- [0x0000002420 - 0x000000242f] io
> PCI: 01:04.2 10 <- [0x0000002400 - 0x000000241f] io
> PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io
> PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
> PCI: 00:19.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
> Done setting resources.
> Done allocating resources.
> Enabling resourcess...
> PCI: 00:18.0 cmd <- 140
> PCI: 01:01.0 bridge ctrl <- 0003
> PCI: 01:01.0 cmd <- 146
> PCI: 02:09.0 subsystem <- 10f1/2881
> PCI: 02:09.0 cmd <- 142
> PCI: 02:09.1 subsystem <- 10f1/2881
> PCI: 02:09.1 cmd <- 142
> PCI: 01:01.1 subsystem <- 10f1/2881
> PCI: 01:01.1 cmd <- 146
> PCI: 01:02.1 subsystem <- 10f1/2881
> PCI: 01:02.1 cmd <- 146
> PCI: 01:03.0 bridge ctrl <- 0003
> PCI: 01:03.0 cmd <- 147
> PCI: 04:00.0 subsystem <- 10f1/2881
> PCI: 04:00.0 cmd <- 142
> PCI: 04:00.1 subsystem <- 10f1/2881
> PCI: 04:00.1 cmd <- 142
> PCI: 04:05.0 subsystem <- 10f1/2881
> PCI: 04:05.0 cmd <- 143
> PCI: 04:06.0 subsystem <- 10f1/2881
> PCI: 04:06.0 cmd <- 1c3
> PCI: 01:04.0 subsystem <- 10f1/2881
> PCI: 01:04.0 cmd <- 14f
> w83627hf hwm smbus enabled
> PCI: 01:04.1 subsystem <- 10f1/2881
> PCI: 01:04.1 cmd <- 141
> PCI: 01:04.2 subsystem <- 10f1/2881
> PCI: 01:04.2 cmd <- 141
> PCI: 01:04.3 subsystem <- 10f1/2881
> PCI: 01:04.3 cmd <- 141
> PCI: 00:18.1 subsystem <- 10f1/2881
> PCI: 00:18.1 cmd <- 140
> PCI: 00:18.2 subsystem <- 10f1/2881
> PCI: 00:18.2 cmd <- 140
> PCI: 00:18.3 cmd <- 140
> PCI: 00:19.0 cmd <- 140
> PCI: 00:19.1 cmd <- 140
> PCI: 00:19.2 cmd <- 140
> PCI: 00:19.3 cmd <- 140
> done.
> Initializing devices...
> Root Device init
> APIC_CLUSTER: 0 init
> Initializing CPU #0
> CPU: vendor AMD device 20f12
> Enabling cache
>
> Setting fixed MTRRs(0-88) type: UC
> Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
> Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
> DONE fixed MTRRs
> Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
> Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
> Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
> DONE variable MTRRs
> Clear out the extra MTRR's
>
> MTRR check
> Fixed MTRRs : Enabled
> Variable MTRRs: Enabled
>
> microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
> microcode: patch id that want to apply= 0x0000004d
> microcode: updated to patch id = 0x0000004d success
> Setting up local apic... apic_id: 0 done.
> Clearing memory 1024K - 2097152K: ------------------------------- done
> CPU #0 Initialized
> start_eip=0x00010000
> Initializing CPU #1
> CPU: vendor AMD device 20f12
> Enabling cache
>
> Setting fixed MTRRs(0-88) type: UC
> Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
> Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
> DONE fixed MTRRs
> Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
> Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
> Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
> DONE variable MTRRs
> Clear out the extra MTRR's
>
> MTRR check
> Fixed MTRRs : Enabled
> Variable MTRRs: Enabled
>
> microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
> microcode: patch id that want to apply= 0x0000004d
> microcode: updated to patch id = 0x0000004d success
> Setting up local apic... apic_id: 1 done.
> CPU #1 Initialized
> start_eip=0x00010000
> Initializing CPU #2
> CPU: vendor AMD device 20f12
> Enabling cache
>
> Setting fixed MTRRs(0-88) type: UC
> Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
> Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
> DONE fixed MTRRs
> Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
> Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
> Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
> DONE variable MTRRs
> Clear out the extra MTRR's
>
> MTRR check
> Fixed MTRRs : Enabled
> Variable MTRRs: Enabled
>
> microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
> microcode: patch id that want to apply= 0x0000004d
> microcode: updated to patch id = 0x0000004d success
> Setting up local apic... apic_id: 2 done.
> Clearing memory 2097152K - 5242880K: ----------------++++++++++++++++ done
> CPU #2 Initialized
> start_eip=0x00010000
> Initializing CPU #3
> Waiting for 1 CPUS to stop
> CPU: vendor AMD device 20f12
> Enabling cache
>
> Setting fixed MTRRs(0-88) type: UC
> Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
> Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
> DONE fixed MTRRs
> Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
> Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
> Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
> DONE variable MTRRs
> Clear out the extra MTRR's
>
> MTRR check
> Fixed MTRRs : Enabled
> Variable MTRRs: Enabled
>
> microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
> microcode: patch id that want to apply= 0x0000004d
> microcode: updated to patch id = 0x0000004d success
> Setting up local apic... apic_id: 3 done.
> CPU #3 Initialized
> All AP CPUs stopped
> PCI: 00:18.0 init
> PCI: 01:01.0 init
> PCI: 02:09.0 init
> PCI: 02:09.1 init
> PCI: 01:03.0 init
> PCI: 04:05.0 init
> PCI: 04:06.0 init
> PCI: 01:04.0 init
> RTC Init
> Invalid CMOS LB checksum
> enabling HPET @0xfed00000
> PNP: 002e.0 init
> PNP: 002e.2 init
> PNP: 002e.5 init
> PNP: 002e.b init
> PCI: 01:04.1 init
> IDE1 IDE0 PCI: 01:04.3 init
> set power on after power fail
> smbus: PCI: 01:04.3[0]->I2C: 01:2d init
> PCI: 00:18.1 init
> PCI: 00:18.2 init
> PCI: 00:18.3 init
> NB: Function 3 Misc Control.. done.
> PCI: 00:19.0 init
> PCI: 00:19.1 init
> PCI: 00:19.2 init
> PCI: 00:19.3 init
> NB: Function 3 Misc Control.. done.
> Devices initialized
> Writing IRQ routing tables to 0xf0000...done.
> Wrote the mp table end at: 00000020 - 000001f4
> Moving GDT to 0x500...ok
> Wrote linuxbios table at: 00000530 - 00000e1c checksum 2ea0
>
> Welcome to elfboot, the open sourced starter.
> January 2002, Eric Biederman.
> Version 1.3
>
> 33:stream_init() - rom_stream: 0xfffc0000 - 0xfffdffff
> Found ELF candiate at offset 0
> Loading Etherboot version: 5.4.1
> Dropping non PT_LOAD segment
> New segment addr 0x10000 size 0x49100 offset 0x0 filesize 0x9ac0
> (cleaned up) New segment addr 0x10000 size 0x49100 offset 0x0 filesize 0x9ac0
> Loading Segment: addr: 0x00000000bff8c000 memsz: 0x0000000000034000 filesz: 0x0000000000009ac0
> Clearing Segment: addr: 0x00000000bff95ac0 memsz: 0x000000000002a540
> Loading Segment: addr: 0x0000000000044000 memsz: 0x0000000000015100 filesz: 0x0000000000000000
> Clearing Segment: addr: 0x0000000000044000 memsz: 0x0000000000015100
> Jumping to boot code at 0x100b0
> CPU 2063 Mhz
> Etherboot 5.4.1 (GPL) http://etherboot.org
> Drivers: TG3 FILO Images: NBI ELF
> Protocols: DHCP TFTP
> Relocating _text from: [000101b0,00059100) to [bfeb70b0,bff00000)
> Boot from (N)etwork (D)isk or (Q)uit? D
>
> Probing pci disk...
> [FILO]FILO version 0.4.1 (root at countzero.vandewege.net) Thu Dec 15 18:44:50 EST 2005
> Press <Enter> for default boot, or <Esc> for boot prompt... 2 1
> boot: hde1:/vmlinuz-2.6.12-9-amd64-generic initrd=/initrd.img-2.6.12-9-amd64-generic ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
> hde: LBA48: WDC WD740GD-00FLC0
> hdf: LBA48: WDC WD740GD-00FLC0
> Mounted ext2fs
> Found Linux version 2.6.12-9-amd64-generic (buildd at king) #1 Mon Oct 10 13:27:39 BST 2005 bzImage.
> Loading kernel... ok
> Loading initrd... ok
> Jumping to entry point...
> [ 0.000000] Bootdata ok (command line is ro root=/dev/md3 console=tty0 console=ttyS0,115200n8)
> [ 0.000000] Linux version 2.6.12-9-amd64-generic (buildd at king) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Mon Oct 10 13:27:39 BST 2005
> [ 0.000000] BIOS-provided physical RAM map:
> [ 0.000000] BIOS-e820: 0000000000000000 - 0000000000000e7c type 16
> [ 0.000000] BIOS-e820: 0000000000000e7c - 00000000000a0000 (usable)
> [ 0.000000] BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16
> [ 0.000000] BIOS-e820: 0000000000100000 - 00000000c0000000 (usable)
> [ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
> [ 0.000000] ACPI: Unable to locate RSDP
> [ 0.000000] Intel MultiProcessor Specification v1.4
> [ 0.000000] Virtual Wire compatibility mode.
> [ 0.000000] OEM ID: TYAN <6>Product ID: S2881 <6>APIC at: 0xFEE00000
> [ 0.000000] Processor #0 15:1 APIC version 16
> [ 0.000000] Processor #1 15:1 APIC version 16
> [ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
> [ 0.000000] Processor #2 15:1 APIC version 16
> [ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
> [ 0.000000] Processor #3 15:1 APIC version 16
> [ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
> [ 0.000000] I/O APIC #4 Version 17 at 0xFEC00000.
> [ 0.000000] I/O APIC #5 Version 17 at 0xFD200000.
> [ 0.000000] I/O APIC #6 Version 17 at 0xFD201000.
> [ 0.000000] Setting APIC routing to flat
> [ 0.000000] Processors: 1
> [ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:40000000)
> [ 0.000000] Checking aperture...
> [ 0.000000] CPU 0: aperture @ f8000000 size 64 MB
> [ 0.000000] CPU 1: aperture @ f8000000 size 64 MB
> [ 0.000000] Built 1 zonelists
> [ 0.000000] Kernel command line: ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
> [ 0.000000] Initializing CPU#0
> [ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
> [ 0.000000] time.c: Using 1.193182 MHz PIT timer.
> [ 0.000000] time.c: Detected 1992.086 MHz processor.
> [ 13.476890] time.c: Using PIT/TSC based timekeeping.
> [ 13.477331] Console: colour dummy device 80x25
> [ 13.697387] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
> [ 13.712991] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
> [ 13.789909] Memory: 4101416k/5242880k available (1620k kernel code, 92332k reserved, 997k data, 136k init)
> [ 13.819815] Security Framework v1.0.0 initialized
> [ 13.824992] SELinux: Disabled at boot.
> [ 13.829226] Mount-cache hash table entries: 256
> [ 13.834275] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> [ 13.842538] CPU: L2 Cache: 1024K (64 bytes/line)
> [ 13.847866] CPU: stepping 02
> [ 13.851414] checking if image is initramfs... it is
> [ 14.188550] Using IO-APIC 4
> [ 14.191771] Using IO-APIC 5
> [ 14.194987] Using IO-APIC 6
> [ 14.208302] Using local APIC timer interrupts.
> [ 14.263629] Detected 12.450 MHz APIC timer.
> [ 14.268446] testing NMI watchdog ... OK.
> [ 14.282975] NET: Registered protocol family 16
> [ 14.288476] PCI: Using configuration type 1
> [ 14.293313] mtrr: v2.0 (20020519)
> [ 14.297419] ACPI: Subsystem revision 20050729
> [ 14.302456] ACPI: Interpreter disabled.
> [ 14.306890] Linux Plug and Play Support v0.97 (c) Adam Belay
> [ 14.313412] pnp: PnP ACPI: disabled
> [ 14.317485] usbcore: registered new driver usbfs
> [ 14.322838] usbcore: registered new driver hub
> [ 14.328010] PCI: Probing PCI hardware
> [ 14.332261] PCI: Probing PCI hardware (bus 00)
> [ 14.338761] PCI: Discovered primary peer bus 01 [IRQ]
> [ 14.344593] PCI: Using IRQ router default [1022/7468] at 0000:01:04.0
> [ 14.352035] PCI->APIC IRQ transform: 0000:01:04.2[D] -> IRQ 19
> [ 14.358802] PCI->APIC IRQ transform: 0000:02:09.0[A] -> IRQ 24
> [ 14.365533] PCI->APIC IRQ transform: 0000:02:09.1[B] -> IRQ 25
> [ 14.372248] PCI->APIC IRQ transform: 0000:04:00.0[D] -> IRQ 19
> [ 14.379040] PCI->APIC IRQ transform: 0000:04:00.1[D] -> IRQ 19
> [ 14.385808] PCI->APIC IRQ transform: 0000:04:05.0[A] -> IRQ 17
> [ 14.392539] PCI->APIC IRQ transform: 0000:04:06.0[A] -> IRQ 18
> [ 14.399347] PCI-DMA: Disabling AGP.
> [ 14.403460] PCI-DMA: aperture base @ f8000000 size 65536 KB
> [ 14.409947] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
> [ 14.417699] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
> [ 14.426219] audit: initializing netlink socket (disabled)
> [ 14.432466] audit: initialized
> [ 14.436078] VFS: Disk quotas dquot_6.5.1
> [ 14.440654] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
> [ 14.448113] devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
> [ 14.455261] devfs: boot_options: 0x0
> [ 14.459445] Initializing Cryptographic API
> [ 14.464203] PCI: MSI quirk detected. pci_msi_quirk set.
> [ 14.470274] PCI: MSI quirk detected. pci_msi_quirk set.
> [ 14.490389] Linux agpgart interface v0.101 (c) Dave Jones
> [ 14.496711] PNP: No PS/2 controller found. Probing ports directly.
> [ 14.505346] serio: i8042 AUX port at 0x60,0x64 irq 12
> [ 14.511273] serio: i8042 KBD port at 0x60,0x64 irq 1
> [ 14.516994] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
> [ 14.526203] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> [ 14.533322] io scheduler noop registered
> [ 14.537861] io scheduler anticipatory registered
> [ 14.543217] io scheduler deadline registered
> [ 14.548185] io scheduler cfq registered
> [ 14.552892] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
> [ 14.561690] NET: Registered protocol family 2
> [ 14.576640] IP: routing cache hash table of 65536 buckets, 512Kbytes
> [ 14.584455] TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
> [ 14.596145] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
> [ 14.604232] TCP: Hash tables configured (established 524288 bind 65536)
> [ 14.611945] NET: Registered protocol family 8
> [ 14.616960] NET: Registered protocol family 20
> [ 14.622278] Freeing unused kernel memory: 136k freed
> Loading, please wait...
> Begin: Loading modules ...
> [ 14.645287] input: AT Translated Set 2 keyboard on isa0060/serio0
> [ 14.657083] Capability LSM initialized
> [ 14.669870] NET: Registered protocol family 1
> [ 14.686443] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> [ 14.693755] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> [ 14.707909] AMD8111: IDE controller at PCI slot 0000:01:04.1
> [ 14.714477] AMD8111: chipset revision 3
> [ 14.718933] AMD8111: not 100% native mode: will probe irqs later
> [ 14.725869] AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller
> [ 14.732469] ide0: BM-DMA at 0x2420-0x2427, BIOS settings: hda:pio, hdb:pio
> [ 14.740909] ide1: BM-DMA at 0x2428-0x242f, BIOS settings: hdc:pio, hdd:pio
> [ 15.881489] hdd: CD-224E, ATAPI CD/DVD-ROM drive
> [ 15.937874] ide1 at 0x170-0x177,0x376 on irq 15
> [ 18.513088] hdd: ATAPI 24X CD-ROM drive, 128kB Cache
> [ 18.518889] Uniform CD-ROM driver Revision: 3.20
> [ 18.772153] tg3.c:v3.31 (June 8, 2005)
> [ 18.780608] eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:24
> [ 18.794116] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
> [ 18.803789] eth0: dma_rwctrl[769f4000]
> [ 18.818576] eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:25
> [ 18.832075] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
> [ 18.841730] eth1: dma_rwctrl[769f4000]
> [ 18.854427] ohci_hcd 0000:04:00.0: Advanced Micro Devices [AMD] AMD-8111 USB
> [ 18.862741] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
> [ 18.871275] ohci_hcd 0000:04:00.0: irq 19, io mem 0xfd000000
> [ 18.930659] hub 1-0:1.0: USB hub found
> [ 18.935018] hub 1-0:1.0: 3 ports detected
> [ 18.942617] ohci_hcd 0000:04:00.1: Advanced Micro Devices [AMD] AMD-8111 USB (#2)
> [ 18.951303] ohci_hcd 0000:04:00.1: new USB bus registered, assigned bus number 2
> [ 18.959848] ohci_hcd 0000:04:00.1: irq 19, io mem 0xfd001000
> [ 19.018622] hub 2-0:1.0: USB hub found
> [ 19.022997] hub 2-0:1.0: 3 ports detected
> [ 19.040635] SCSI subsystem initialized
> [ 19.047043] ata1: SATA max UDMA/100 cmd 0xFFFFC20000014080 ctl 0xFFFFC2000001408A bmdma 0xFFFFC20000014000 irq 17
> [ 19.058983] ata2: SATA max UDMA/100 cmd 0xFFFFC200000140C0 ctl 0xFFFFC200000140CA bmdma 0xFFFFC20000014008 irq 17
> [ 19.070913] ata3: SATA max UDMA/100 cmd 0xFFFFC20000014280 ctl 0xFFFFC2000001428A bmdma 0xFFFFC20000014200 irq 17
> [ 19.082807] ata4: SATA max UDMA/100 cmd 0xFFFFC200000142C0 ctl 0xFFFFC200000142CA bmdma 0xFFFFC20000014208 irq 17
> [ 19.449906] ata1: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
> [ 19.458221] ata1: dev 0 configured for UDMA/100
> [ 19.463445] scsi0 : sata_sil
> [ 19.821814] ata2: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
> [ 19.830068] ata2: dev 0 configured for UDMA/100
> [ 19.835281] scsi1 : sata_sil
> [ 20.193734] ata3: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
> [ 20.202017] ata3: dev 0 configured for UDMA/100
> [ 20.207255] scsi2 : sata_sil
> [ 20.565656] ata4: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
> [ 20.573948] ata4: dev 0 configured for UDMA/100
> [ 20.579205] scsi3 : sata_sil
> [ 20.582618] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
> [ 20.589939] Type: Direct-Access ANSI SCSI revision: 05
> [ 20.598797] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
> [ 20.606107] Type: Direct-Access ANSI SCSI revision: 05
> [ 20.614984] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
> [ 20.622302] Type: Direct-Access ANSI SCSI revision: 05
> [ 20.631150] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
> [ 20.638484] Type: Direct-Access ANSI SCSI revision: 05
> [ 22.664450] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.672077] SCSI device sda: drive cache: write back
> [ 22.677847] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.685509] SCSI device sda: drive cache: write back
> [ 22.691291] /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
> [ 22.706480] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
> [ 22.713735] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.721369] SCSI device sdb: drive cache: write back
> [ 22.727153] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.734791] SCSI device sdb: drive cache: write back
> [ 22.740529] /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4
> [ 22.758728] Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
> [ 22.765981] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.773675] SCSI device sdc: drive cache: write back
> [ 22.779461] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.787123] SCSI device sdc: drive cache: write back
> [ 22.792871] /dev/scsi/host2/bus0/target0/lun0: p1 p2 p3 p4
> [ 22.812560] Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
> [ 22.819822] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.827507] SCSI device sdd: drive cache: write back
> [ 22.833316] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
> [ 22.841024] SCSI device sdd: drive cache: write back
> [ 22.846788] /dev/scsi/host3/bus0/target0/lun0: p1 p2 p3 p4
> [ 22.867064] Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
> Done.
> Begin: Initializing /dev ...
> Done.
> Begin: Running /scripts/init-premount ...
> FATAL: Error inserting fan (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/fan.ko): No such device
> FATAL: Error inserting thermal (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/thermal.ko): No such device
> Done.
> Begin: Mounting root file system ...
> Begin: Running /scripts/local-top ...
> [ 23.224330] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
> [ 23.233979] md: raid1 personality registered as nr 3
> [ 23.249716] raid5: automatically using best checksumming function: generic_sse
> [ 23.262592] generic_sse: 6044.000 MB/sec
> [ 23.267530] raid5: using function: generic_sse (6044.000 MB/sec)
> [ 23.275210] md: raid5 personality registered as nr 4
> [ 23.601260] devfs_mk_dev: could not append to parent for md/0
> [ 23.609757] md: md0 stopped.
> [ 23.614044] md: bind<sdb1>
> [ 23.617323] md: bind<sdc1>
> [ 23.620564] md: bind<sdd1>
> [ 23.623805] md: bind<sda1>
> [ 23.626995] raid1: raid set md0 active with 4 out of 4 mirrors
> mdadm: /dev/md0 has been started with 4 drives.
> [ 23.641055] devfs_mk_dev: could not append to parent for md/1
> [ 23.649588] md: md1 stopped.
> [ 23.653883] md: bind<sdb2>
> [ 23.657143] md: bind<sdc2>
> [ 23.660419] md: bind<sdd2>
> [ 23.663659] md: bind<sda2>
> [ 23.666829] raid5: device sda2 operational as raid disk 0
> [ 23.673104] raid5: device sdd2 operational as raid disk 3
> [ 23.679316] raid5: device sdc2 operational as raid disk 2
> [ 23.685598] raid5: device sdb2 operational as raid disk 1
> [ 23.692275] raid5: allocated 4270kB for md1
> [ 23.697098] raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
> [ 23.705958] RAID5 conf printout:
> [ 23.709709] --- rd:4 wd:4 fd:0
> [ 23.713348] disk 0, o:1, dev:sda2
> [ 23.717272] disk 1, o:1, dev:sdb2
> [ 23.721214] disk 2, o:1, dev:sdc2
> [ 23.725140] disk 3, o:1, dev:sdd2
> mdadm: /dev/md1 has been started with 4 drives.
> [ 23.740660] devfs_mk_dev: could not append to parent for md/2
> [ 23.749195] md: md2 stopped.
> [ 23.753499] md: bind<sdb3>
> [ 23.756782] md: bind<sdc3>
> [ 23.760050] md: bind<sdd3>
> [ 23.763323] md: bind<sda3>
> [ 23.766489] raid5: device sda3 operational as raid disk 0
> [ 23.772723] raid5: device sdd3 operational as raid disk 3
> [ 23.778971] raid5: device sdc3 operational as raid disk 2
> [ 23.785209] raid5: device sdb3 operational as raid disk 1
> [ 23.791895] raid5: allocated 4270kB for md2
> [ 23.796733] raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
> [ 23.805597] RAID5 conf printout:
> [ 23.809358] --- rd:4 wd:4 fd:0
> [ 23.812987] disk 0, o:1, dev:sda3
> [ 23.816945] disk 1, o:1, dev:sdb3
> [ 23.820871] disk 2, o:1, dev:sdc3
> [ 23.824795] disk 3, o:1, dev:sdd3
> mdadm: /dev/md2 has been started with 4 drives.
> [ 23.844303] devfs_mk_dev: could not append to parent for md/3
> [ 23.852907] md: md3 stopped.
> [ 23.857209] md: bind<sdb4>
> [ 23.860491] md: bind<sdc4>
> [ 23.863751] md: bind<sdd4>
> [ 23.867023] md: bind<sda4>
> [ 23.870187] md: md3: raid array is not clean -- starting background reconstruction
> [ 23.878970] raid5: device sda4 operational as raid disk 0
> [ 23.885236] raid5: device sdd4 operational as raid disk 3
> [ 23.891492] raid5: device sdc4 operational as raid disk 2
> [ 23.897764] raid5: device sdb4 operational as raid disk 1
> [ 23.904458] raid5: allocated 4270kB for md3
> [ 23.909322] raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2
> [ 23.918195] RAID5 conf printout:
> [ 23.921952] --- rd:4 wd:4 fd:0
> [ 23.925610] disk 0, o:1, dev:sda4
> [ 23.929560] disk 1, o:1, dev:sdb4
> [ 23.933493] disk 2, o:1, dev:sdc4
> [ 23.937443] disk 3, o:1, dev:sdd4
> [ 23.941428] ....<6>md: syncing RAID array md3
> [ 23.946502] md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
> [ 23.954669] md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction.
> [ 23.966246] md: using 128k window, over a total of 67657664 blocks.
> mdadm: /dev/md3 has been started with 4 drives.
> Done.
> Begin: Running /scripts/local-premount ...
> [ 24.000782] Attempting manual resume
> [ 24.006995] swsusp: Suspend partition has wrong signature?
> Done.
> [ 24.115879] kjournald starting. Commit interval 5 seconds
> [ 24.122230] EXT3-fs: mounted filesystem with ordered data mode.
> Begin: Running /scripts/local-bottom ...
> Done.
> Done.
> Begin: Running /scripts/init-bottom ...
> Done.
> * version 2.86 booting
> * Starting RAID devices... [ ok ]
> * Starting hardware event daemon... [ ok ]
> * Creating initial device nodes...
>
> LinuxBIOS-1.1.8_s2881_Fallback Thu Dec 15 18:45:48 EST 2005 starting...
> (0,1) link=00
> (1,0) link=00
> 02 nodes initialized.
> core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
> SBLink=02
> NC node|link=02
--
Ward Vandewege <ward at fsf.org>
Free Software Foundation - Senior System Administrator
-------------- next part --------------
LinuxBIOS-1.1.8_s2881_Fallback Tue Jan 3 17:36:16 EST 2006 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
ht reset -
LinuxBIOS-1.1.8_s2881_Fallback Tue Jan 3 17:36:16 EST 2006 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
Ram1.00
Ram1.01
Ram2.00
Ram2.01
Ram3
Initializing memory: done
Initializing memory: done
Ram4
v_esp=000cfd40
cpu_reset = 00000000
Clearing initial memory region: No cache as ram now - Use Ram as Stack now - done
new_cpu_reset = 00000000
Copying LinuxBIOS to ram.
src=fffe0004
dst=00004000
linxbios_ram.bin length = 0001928c
Jumping to LinuxBIOS.
LinuxBIOS-1.1.8_s2881_Fallback Tue Jan 3 17:36:16 EST 2006 booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=1
CPU: APIC: 00 enabled
CPU: APIC: 01 enabled
PCI: 00:19.0 [1022/1100] enabled
PCI: 00:19.1 [1022/1101] enabled
PCI: 00:19.2 [1022/1102] enabled
PCI: 00:19.3 [1022/1103] enabled
PCI: 00:19.3 siblings=1
CPU: APIC: 02 enabled
CPU: APIC: 03 enabled
PCI: pci_scan_bus for bus 0
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
PCI: 00:19.0 [1022/1100] enabled
PCI: 00:19.1 [1022/1101] enabled
PCI: 00:19.2 [1022/1102] enabled
PCI: 00:19.3 [1022/1103] enabled
PCI: 01:00.0 [1022/7450] enabled
PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003
PCI: 01:00.0 [1022/7460] enabled
PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007
PCI: pci_scan_bus for bus 1
PCI: 01:01.0 [1022/7450] enabled
PCI: 01:01.1 [1022/7451] enabled
PCI: 01:02.0 [1022/7450] enabled
PCI: 01:02.1 [1022/7451] enabled
PCI: 01:03.0 [1022/7460] enabled
PCI: 01:04.0 [1022/7468] enabled
PCI: 01:04.1 [1022/7469] enabled
PCI: 01:04.2 [1022/746a] enabled
PCI: 01:04.3 [1022/746b] enabled
PCI: pci_scan_bus for bus 2
PCI: 02:09.0 [14e4/1648] enabled
PCI: 02:09.1 [14e4/1648] enabled
Disabling static device: PCI: 02:0a.0
Disabling static device: PCI: 02:0a.1
PCI: pci_scan_bus returning with max=02
PCI: 02: 100MHz PCI-X
PCI: pci_scan_bus for bus 3
PCI: pci_scan_bus returning with max=03
PCI: 03: 133MHz PCI-X
PCI: pci_scan_bus for bus 4
PCI: 04:00.0 [1022/7464] enabled
PCI: 04:00.1 [1022/7464] enabled
PCI: 04:05.0 [1095/3114] enabled
PCI: 04:06.0 [1002/4752] enabled
PCI: pci_scan_bus returning with max=04
PNP: 002e.0 enabled
PNP: 002e.1 disabled
PNP: 002e.2 enabled
PNP: 002e.3 disabled
PNP: 002e.5 enabled
PNP: 002e.6 disabled
PNP: 002e.7 disabled
PNP: 002e.8 disabled
PNP: 002e.9 disabled
PNP: 002e.a disabled
PNP: 002e.b enabled
smbus: PCI: 01:04.3[0]->I2C: 01:50 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:51 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:52 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:53 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:54 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:55 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:56 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:57 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:2d enabled
smbus: PCI: 01:04.3[0]->I2C: 01:2a enabled
smbus: PCI: 01:04.3[0]->I2C: 01:49 enabled
smbus: PCI: 01:04.3[0]->I2C: 01:4a enabled
PCI: pci_scan_bus returning with max=04
PCI: pci_scan_bus returning with max=04
done
Allocating resources...
Reading resources...
PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io
PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem
PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem
Done reading resources.
Setting resources...
PCI: 00:18.0 1ba <- [0x00fd300000 - 0x00fd2fffff] prefmem <node 0 link 2>
PCI: 00:18.0 1c2 <- [0x0000001000 - 0x0000002fff] io <node 0 link 2>
PCI: 00:18.0 1b2 <- [0x00fc000000 - 0x00fd2fffff] mem <node 0 link 2>
PCI: 01:01.0 20 <- [0x00fd100000 - 0x00fd1fffff] bus 2 mem
PCI: 02:09.0 10 <- [0x00fd100000 - 0x00fd10ffff] mem64
PCI: 02:09.0 18 <- [0x00fd110000 - 0x00fd11ffff] mem64
PCI: 02:09.1 10 <- [0x00fd120000 - 0x00fd12ffff] mem64
PCI: 02:09.1 18 <- [0x00fd130000 - 0x00fd13ffff] mem64
PCI: 01:01.1 10 <- [0x00fd200000 - 0x00fd200fff] mem64
PCI: 01:02.1 10 <- [0x00fd201000 - 0x00fd201fff] mem64
PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io
PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 mem
PCI: 04:00.0 10 <- [0x00fd000000 - 0x00fd000fff] mem
PCI: 04:00.1 10 <- [0x00fd001000 - 0x00fd001fff] mem
PCI: 04:05.0 10 <- [0x0000001410 - 0x0000001417] io
PCI: 04:05.0 14 <- [0x0000001430 - 0x0000001433] io
PCI: 04:05.0 18 <- [0x0000001420 - 0x0000001427] io
PCI: 04:05.0 1c <- [0x0000001440 - 0x0000001443] io
PCI: 04:05.0 20 <- [0x0000001400 - 0x000000140f] io
PCI: 04:05.0 24 <- [0x00fd003000 - 0x00fd0033ff] mem
PCI: 04:06.0 10 <- [0x00fc000000 - 0x00fcffffff] mem
PCI: 04:06.0 14 <- [0x0000001000 - 0x00000010ff] io
PCI: 04:06.0 18 <- [0x00fd002000 - 0x00fd002fff] mem
PCI: 04:06.0 30 <- [0x00fff80000 - 0x00fff9ffff] romem
PNP: 002e.0 60 <- [0x00000003f0 - 0x00000003f7] io
PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq
PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq
PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] io
PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irq
PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io
PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io
PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq
PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq
PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] io
PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq
PCI: 01:04.1 20 <- [0x0000002420 - 0x000000242f] io
PCI: 01:04.2 10 <- [0x0000002400 - 0x000000241f] io
PCI: 01:04.3 58 <- [0x0000002000 - 0x00000020ff] io
PCI: 00:18.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
PCI: 00:19.3 94 <- [0x00f8000000 - 0x00fbffffff] mem <gart>
Done setting resources.
Done allocating resources.
Enabling resourcess...
PCI: 00:18.0 cmd <- 140
PCI: 01:01.0 bridge ctrl <- 0003
PCI: 01:01.0 cmd <- 146
PCI: 02:09.0 subsystem <- 10f1/2881
PCI: 02:09.0 cmd <- 142
PCI: 02:09.1 subsystem <- 10f1/2881
PCI: 02:09.1 cmd <- 142
PCI: 01:01.1 subsystem <- 10f1/2881
PCI: 01:01.1 cmd <- 146
PCI: 01:02.1 subsystem <- 10f1/2881
PCI: 01:02.1 cmd <- 146
PCI: 01:03.0 bridge ctrl <- 0003
PCI: 01:03.0 cmd <- 147
PCI: 04:00.0 subsystem <- 10f1/2881
PCI: 04:00.0 cmd <- 142
PCI: 04:00.1 subsystem <- 10f1/2881
PCI: 04:00.1 cmd <- 142
PCI: 04:05.0 subsystem <- 10f1/2881
PCI: 04:05.0 cmd <- 143
PCI: 04:06.0 subsystem <- 10f1/2881
PCI: 04:06.0 cmd <- 1c3
PCI: 01:04.0 subsystem <- 10f1/2881
PCI: 01:04.0 cmd <- 14f
w83627hf hwm smbus enabled
PCI: 01:04.1 subsystem <- 10f1/2881
PCI: 01:04.1 cmd <- 141
PCI: 01:04.2 subsystem <- 10f1/2881
PCI: 01:04.2 cmd <- 141
PCI: 01:04.3 subsystem <- 10f1/2881
PCI: 01:04.3 cmd <- 141
PCI: 00:18.1 subsystem <- 10f1/2881
PCI: 00:18.1 cmd <- 140
PCI: 00:18.2 subsystem <- 10f1/2881
PCI: 00:18.2 cmd <- 140
PCI: 00:18.3 cmd <- 140
PCI: 00:19.0 cmd <- 140
PCI: 00:19.1 cmd <- 140
PCI: 00:19.2 cmd <- 140
PCI: 00:19.3 cmd <- 140
done.
Initializing devices...
Root Device init
APIC_CLUSTER: 0 init
Initializing CPU #0
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 0 done.
Clearing memory 1024K - 2097152K: ------------------------------- done
CPU #0 Initialized
start_eip=0x00010000
Initializing CPU #1
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 1 done.
CPU #1 Initialized
start_eip=0x00010000
Initializing CPU #2
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 2 done.
Clearing memory 2097152K - 5242880K: ----------------++++++++++++++++ done
CPU #2 Initialized
start_eip=0x00010000
Initializing CPU #3
Waiting for 1 CPUS to stop
CPU: vendor AMD device 20f12
Enabling cache
Setting fixed MTRRs(0-88) type: UC
Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM
Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM
DONE fixed MTRRs
Setting variable MTRR 0, base: 0MB, range: 4096MB, type WB
Setting variable MTRR 1, base: 4096MB, range: 1024MB, type WB
Setting variable MTRR 2, base: 3072MB, range: 1024MB, type UC
DONE variable MTRRs
Clear out the extra MTRR's
MTRR check
Fixed MTRRs : Enabled
Variable MTRRs: Enabled
microcode: equivalent processor rev id = 0x0210, patch id = 0x00000000
microcode: patch id that want to apply= 0x0000004d
microcode: updated to patch id = 0x0000004d success
Setting up local apic... apic_id: 3 done.
CPU #3 Initialized
All AP CPUs stopped
PCI: 00:18.0 init
PCI: 01:01.0 init
PCI: 02:09.0 init
PCI: 02:09.1 init
PCI: 01:03.0 init
PCI: 04:05.0 init
PCI: 04:06.0 init
PCI: 01:04.0 init
RTC Init
Invalid CMOS LB checksum
enabling HPET @0xfed00000
PNP: 002e.0 init
PNP: 002e.2 init
PNP: 002e.5 init
PNP: 002e.b init
PCI: 01:04.1 init
IDE1 IDE0 PCI: 01:04.3 init
set power on after power fail
smbus: PCI: 01:04.3[0]->I2C: 01:2d init
PCI: 00:18.1 init
PCI: 00:18.2 init
PCI: 00:18.3 init
NB: Function 3 Misc Control.. done.
PCI: 00:19.0 init
PCI: 00:19.1 init
PCI: 00:19.2 init
PCI: 00:19.3 init
NB: Function 3 Misc Control.. done.
Devices initialized
Writing IRQ routing tables to 0xf0000...done.
Wrote the mp table end at: 00000020 - 000001f4
Moving GDT to 0x500...ok
Wrote linuxbios table at: 00000530 - 00000e10 checksum 54d5
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
33:stream_init() - rom_stream: 0xfffc0000 - 0xfffdffff
Found ELF candiate at offset 0
Loading Etherboot version: 5.4.1
Dropping non PT_LOAD segment
New segment addr 0x10000 size 0x49180 offset 0x0 filesize 0x9c90
(cleaned up) New segment addr 0x10000 size 0x49180 offset 0x0 filesize 0x9c90
Loading Segment: addr: 0x00000000bff8c000 memsz: 0x0000000000034000 filesz: 0x0000000000009c90
Clearing Segment: addr: 0x00000000bff95c90 memsz: 0x000000000002a370
Loading Segment: addr: 0x0000000000044000 memsz: 0x0000000000015180 filesz: 0x0000000000000000
Clearing Segment: addr: 0x0000000000044000 memsz: 0x0000000000015180
Jumping to boot code at 0x100b0
CPU 2064 Mhz
Etherboot 5.4.1 (GPL) http://etherboot.org
Drivers: TG3 FILO Images: NBI ELF
Protocols: DHCP TFTP
Relocating _text from: [000101b0,00059180) to [bfeb7030,bff00000)
Boot from (N)etwork (D)isk or (Q)uit? D
Probing pci disk...
[FILO]FILO version 0.4.1 (root at countzero.vandewege.net) Tue Jan 3 17:32:29 EST 2006
Press <Enter> for default boot, or <Esc> for boot prompt... 2 1 timed out
boot: hde1:/vmlinuz-2.6.12-9-amd64-generic initrd=/initrd.img-2.6.12-9-amd64-generic ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
hde: LBA48: WDC WD740GD-00FLC0
hdf: LBA48: WDC WD740GD-00FLC0
Mounted ext2fs
Found Linux version 2.6.12-9-amd64-generic (buildd at king) #1 Mon Oct 10 13:27:39 BST 2005 bzImage.
Loading kernel... ok
Loading initrd... ok
Jumping to entry point...
[ 0.000000] Bootdata ok (command line is ro root=/dev/md3 console=tty0 console=ttyS0,115200n8)
[ 0.000000] Linux version 2.6.12-9-amd64-generic (buildd at king) (gcc version 3.4.5 20050809 (prerelease) (Ubuntu 3.4.4-6ubuntu8)) #1 Mon Oct 10 13:27:39 BST 2005
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 0000000000000e7c type 16
[ 0.000000] BIOS-e820: 0000000000000e7c - 00000000000a0000 (usable)
[ 0.000000] BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16
[ 0.000000] BIOS-e820: 0000000000100000 - 00000000c0000000 (usable)
[ 0.000000] BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
[ 0.000000] ACPI: Unable to locate RSDP
[ 0.000000] Intel MultiProcessor Specification v1.4
[ 0.000000] Virtual Wire compatibility mode.
[ 0.000000] OEM ID: TYAN <6>Product ID: S2881 <6>APIC at: 0xFEE00000
[ 0.000000] Processor #0 15:1 APIC version 16
[ 0.000000] Processor #1 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] Processor #2 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] Processor #3 15:1 APIC version 16
[ 0.000000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[ 0.000000] I/O APIC #4 Version 17 at 0xFEC00000.
[ 0.000000] I/O APIC #5 Version 17 at 0xFD200000.
[ 0.000000] I/O APIC #6 Version 17 at 0xFD201000.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] Processors: 1
[ 0.000000] Allocating PCI resources starting at c0000000 (gap: c0000000:40000000)
[ 0.000000] Checking aperture...
[ 0.000000] CPU 0: aperture @ f8000000 size 64 MB
[ 0.000000] CPU 1: aperture @ f8000000 size 64 MB
[ 0.000000] Built 1 zonelists
[ 0.000000] Kernel command line: ro root=/dev/md3 console=tty0 console=ttyS0,115200n8
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[ 0.000000] time.c: Using 1.193182 MHz PIT timer.
[ 0.000000] time.c: Detected 1991.567 MHz processor.
[ 13.382487] time.c: Using PIT/TSC based timekeeping.
[ 13.382927] Console: colour dummy device 80x25
[ 13.602936] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 13.618545] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 13.695497] Memory: 4101416k/5242880k available (1620k kernel code, 92332k reserved, 997k data, 136k init)
[ 13.725327] Security Framework v1.0.0 initialized
[ 13.730503] SELinux: Disabled at boot.
[ 13.734726] Mount-cache hash table entries: 256
[ 13.739776] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
[ 13.748068] CPU: L2 Cache: 1024K (64 bytes/line)
[ 13.753397] CPU: stepping 02
[ 13.756953] checking if image is initramfs... it is
[ 14.094094] Using IO-APIC 4
[ 14.097350] Using IO-APIC 5
[ 14.100593] Using IO-APIC 6
[ 14.113926] Using local APIC timer interrupts.
[ 14.169306] Detected 12.447 MHz APIC timer.
[ 14.174168] testing NMI watchdog ... OK.
[ 14.188739] NET: Registered protocol family 16
[ 14.194273] PCI: Using configuration type 1
[ 14.199124] mtrr: v2.0 (20020519)
[ 14.203233] ACPI: Subsystem revision 20050729
[ 14.208291] ACPI: Interpreter disabled.
[ 14.212726] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.219295] pnp: PnP ACPI: disabled
[ 14.223386] usbcore: registered new driver usbfs
[ 14.228755] usbcore: registered new driver hub
[ 14.233943] PCI: Probing PCI hardware
[ 14.238176] PCI: Probing PCI hardware (bus 00)
[ 14.244682] PCI: Discovered primary peer bus 01 [IRQ]
[ 14.250557] PCI: Using IRQ router default [1022/7468] at 0000:01:04.0
[ 14.258038] PCI->APIC IRQ transform: 0000:01:04.2[D] -> IRQ 19
[ 14.264805] PCI->APIC IRQ transform: 0000:02:09.0[A] -> IRQ 24
[ 14.271568] PCI->APIC IRQ transform: 0000:02:09.1[B] -> IRQ 25
[ 14.278315] PCI->APIC IRQ transform: 0000:04:00.0[D] -> IRQ 19
[ 14.285099] PCI->APIC IRQ transform: 0000:04:00.1[D] -> IRQ 19
[ 14.291873] PCI->APIC IRQ transform: 0000:04:05.0[A] -> IRQ 17
[ 14.298639] PCI->APIC IRQ transform: 0000:04:06.0[A] -> IRQ 18
[ 14.305469] PCI-DMA: Disabling AGP.
[ 14.309565] PCI-DMA: aperture base @ f8000000 size 65536 KB
[ 14.316026] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
[ 14.323800] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
[ 14.332310] audit: initializing netlink socket (disabled)
[ 14.338571] audit: initialized
[ 14.342183] VFS: Disk quotas dquot_6.5.1
[ 14.346741] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 14.354242] devfs: 2004-01-31 Richard Gooch (rgooch at atnf.csiro.au)
[ 14.361388] devfs: boot_options: 0x0
[ 14.365554] Initializing Cryptographic API
[ 14.370320] PCI: MSI quirk detected. pci_msi_quirk set.
[ 14.376390] PCI: MSI quirk detected. pci_msi_quirk set.
[ 14.396511] Linux agpgart interface v0.101 (c) Dave Jones
[ 14.402839] PNP: No PS/2 controller found. Probing ports directly.
[ 14.411607] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 14.417510] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 14.423273] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
[ 14.432480] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 14.439569] io scheduler noop registered
[ 14.444130] io scheduler anticipatory registered
[ 14.449492] io scheduler deadline registered
[ 14.454450] io scheduler cfq registered
[ 14.459156] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 14.467995] NET: Registered protocol family 2
[ 14.482953] IP: routing cache hash table of 65536 buckets, 512Kbytes
[ 14.490780] TCP established hash table entries: 524288 (order: 10, 4194304 bytes)
[ 14.502485] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 14.510542] TCP: Hash tables configured (established 524288 bind 65536)
[ 14.518280] NET: Registered protocol family 8
[ 14.523312] NET: Registered protocol family 20
[ 14.528620] Freeing unused kernel memory: 136k freed
Loading, please wait...
Begin: Loading modules ...
[ 14.552088] input: AT Translated Set 2 keyboard on isa0060/serio0
[ 14.563428] Capability LSM initialized
[ 14.576238] NET: Registered protocol family 1
[ 14.592822] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 14.600210] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 14.614405] AMD8111: IDE controller at PCI slot 0000:01:04.1
[ 14.620961] AMD8111: chipset revision 3
[ 14.625398] AMD8111: not 100% native mode: will probe irqs later
[ 14.632349] AMD8111: 0000:01:04.1 (rev 03) UDMA133 controller
[ 14.639007] ide0: BM-DMA at 0x2420-0x2427, BIOS settings: hda:pio, hdb:pio
[ 14.647392] ide1: BM-DMA at 0x2428-0x242f, BIOS settings: hdc:pio, hdd:pio
[ 15.787445] hdd: CD-224E, ATAPI CD/DVD-ROM drive
[ 15.843814] ide1 at 0x170-0x177,0x376 on irq 15
[ 18.418214] hdd: ATAPI 24X CD-ROM drive, 128kB Cache
[ 18.424029] Uniform CD-ROM driver Revision: 3.20
[ 18.679200] tg3.c:v3.31 (June 8, 2005)
[ 18.687669] eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:24
[ 18.701222] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[0]
[ 18.710911] eth0: dma_rwctrl[769f4000]
[ 18.725706] eth1: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:a5:25
[ 18.739240] eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
[ 18.748945] eth1: dma_rwctrl[769f4000]
[ 18.761726] ohci_hcd 0000:04:00.0: Advanced Micro Devices [AMD] AMD-8111 USB
[ 18.770030] ohci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 1
[ 18.778603] ohci_hcd 0000:04:00.0: irq 19, io mem 0xfd000000
[ 18.837669] hub 1-0:1.0: USB hub found
[ 18.842018] hub 1-0:1.0: 3 ports detected
[ 18.849623] ohci_hcd 0000:04:00.1: Advanced Micro Devices [AMD] AMD-8111 USB (#2)
[ 18.858342] ohci_hcd 0000:04:00.1: new USB bus registered, assigned bus number 2
[ 18.866917] ohci_hcd 0000:04:00.1: irq 19, io mem 0xfd001000
[ 18.925606] hub 2-0:1.0: USB hub found
[ 18.929958] hub 2-0:1.0: 3 ports detected
[ 18.947609] SCSI subsystem initialized
[ 18.954053] ata1: SATA max UDMA/100 cmd 0xFFFFC20000014080 ctl 0xFFFFC2000001408A bmdma 0xFFFFC20000014000 irq 17
[ 18.965952] ata2: SATA max UDMA/100 cmd 0xFFFFC200000140C0 ctl 0xFFFFC200000140CA bmdma 0xFFFFC20000014008 irq 17
[ 18.977888] ata3: SATA max UDMA/100 cmd 0xFFFFC20000014280 ctl 0xFFFFC2000001428A bmdma 0xFFFFC20000014200 irq 17
[ 18.989796] ata4: SATA max UDMA/100 cmd 0xFFFFC200000142C0 ctl 0xFFFFC200000142CA bmdma 0xFFFFC20000014208 irq 17
[ 19.356748] ata1: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 19.365079] ata1: dev 0 configured for UDMA/100
[ 19.370326] scsi0 : sata_sil
[ 19.728542] ata2: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 19.736868] ata2: dev 0 configured for UDMA/100
[ 19.742125] scsi1 : sata_sil
[ 20.100343] ata3: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 20.108673] ata3: dev 0 configured for UDMA/100
[ 20.113919] scsi2 : sata_sil
[ 20.472138] ata4: dev 0 ATA, max UDMA/133, 145226112 sectors: lba48
[ 20.480443] ata4: dev 0 configured for UDMA/100
[ 20.485690] scsi3 : sata_sil
[ 20.489092] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.496427] Type: Direct-Access ANSI SCSI revision: 05
[ 20.505313] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.512607] Type: Direct-Access ANSI SCSI revision: 05
[ 20.521467] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.528815] Type: Direct-Access ANSI SCSI revision: 05
[ 20.537688] Vendor: ATA Model: WDC WD740GD-00FL Rev: 33.0
[ 20.544977] Type: Direct-Access ANSI SCSI revision: 05
[ 22.570354] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.578060] SCSI device sda: drive cache: write back
[ 22.583874] SCSI device sda: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.591514] SCSI device sda: drive cache: write back
[ 22.597270] /dev/scsi/host0/bus0/target0/lun0: p1 p2 p3 p4
[ 22.614922] Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
[ 22.622193] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.629880] SCSI device sdb: drive cache: write back
[ 22.635684] SCSI device sdb: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.643346] SCSI device sdb: drive cache: write back
[ 22.649102] /dev/scsi/host1/bus0/target0/lun0: p1 p2 p3 p4
[ 22.665362] Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
[ 22.672632] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.680274] SCSI device sdc: drive cache: write back
[ 22.686053] SCSI device sdc: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.693715] SCSI device sdc: drive cache: write back
[ 22.699471] /dev/scsi/host2/bus0/target0/lun0: p1 p2 p3 p4
[ 22.717266] Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
[ 22.724550] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.732228] SCSI device sdd: drive cache: write back
[ 22.738015] SCSI device sdd: 145226112 512-byte hdwr sectors (74356 MB)
[ 22.745679] SCSI device sdd: drive cache: write back
[ 22.751417] /dev/scsi/host3/bus0/target0/lun0: p1 p2 p3 p4
[ 22.769228] Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Done.
Begin: Initializing /dev ...
Done.
Begin: Running /scripts/init-premount ...
FATAL: Error inserting fan (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/fan.ko): No such device
FATAL: Error inserting thermal (/lib/modules/2.6.12-9-amd64-generic/kernel/drivers/acpi/thermal.ko): No such device
Done.
Begin: Mounting root file system ...
Begin: Running /scripts/local-top ...
[ 23.126611] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[ 23.136234] md: raid1 personality registered as nr 3
[ 23.152012] raid5: automatically using best checksumming function: generic_sse
[ 23.165265] generic_sse: 6040.000 MB/sec
[ 23.170211] raid5: using function: generic_sse (6040.000 MB/sec)
[ 23.177911] md: raid5 personality registered as nr 4
[ 23.503175] devfs_mk_dev: could not append to parent for md/0
[ 23.511685] md: md0 stopped.
[ 23.515982] md: bind<sdb1>
[ 23.519240] md: bind<sdc1>
[ 23.522491] md: bind<sdd1>
[ 23.525746] md: bind<sda1>
[ 23.528967] raid1: raid set md0 active with 4 out of 4 mirrors
mdadm: /dev/md0 has been started with 4 drives.
[ 23.543059] devfs_mk_dev: could not append to parent for md/1
[ 23.551594] md: md1 stopped.
[ 23.555871] md: bind<sdb2>
[ 23.559153] md: bind<sdc2>
[ 23.562397] md: bind<sdd2>
[ 23.565675] md: bind<sda2>
[ 23.568817] raid5: device sda2 operational as raid disk 0
[ 23.575076] raid5: device sdd2 operational as raid disk 3
[ 23.581314] raid5: device sdc2 operational as raid disk 2
[ 23.587560] raid5: device sdb2 operational as raid disk 1
[ 23.594243] raid5: allocated 4270kB for md1
[ 23.599081] raid5: raid level 5 set md1 active with 4 out of 4 devices, algorithm 2
[ 23.607952] RAID5 conf printout:
[ 23.611689] --- rd:4 wd:4 fd:0
[ 23.615320] disk 0, o:1, dev:sda2
[ 23.619244] disk 1, o:1, dev:sdb2
[ 23.623168] disk 2, o:1, dev:sdc2
[ 23.627127] disk 3, o:1, dev:sdd2
mdadm: /dev/md1 has been started with 4 drives.
[ 23.642617] devfs_mk_dev: could not append to parent for md/2
[ 23.651168] md: md2 stopped.
[ 23.655459] md: bind<sdb3>
[ 23.658725] md: bind<sdc3>
[ 23.661974] md: bind<sdd3>
[ 23.665248] md: bind<sda3>
[ 23.668406] raid5: device sda3 operational as raid disk 0
[ 23.674639] raid5: device sdd3 operational as raid disk 3
[ 23.680917] raid5: device sdc3 operational as raid disk 2
[ 23.687201] raid5: device sdb3 operational as raid disk 1
[ 23.693862] raid5: allocated 4270kB for md2
[ 23.698703] raid5: raid level 5 set md2 active with 4 out of 4 devices, algorithm 2
[ 23.707572] RAID5 conf printout:
[ 23.711314] --- rd:4 wd:4 fd:0
[ 23.714961] disk 0, o:1, dev:sda3
[ 23.718893] disk 1, o:1, dev:sdb3
[ 23.722817] disk 2, o:1, dev:sdc3
[ 23.726741] disk 3, o:1, dev:sdd3
mdadm: /dev/md2 has been started with 4 drives.
[ 23.746129] devfs_mk_dev: could not append to parent for md/3
[ 23.754702] md: md3 stopped.
[ 23.758992] md: bind<sdb4>
[ 23.762253] md: bind<sdc4>
[ 23.765497] md: bind<sdd4>
[ 23.768768] md: bind<sda4>
[ 23.771904] md: md3: raid array is not clean -- starting background reconstruction
[ 23.780703] raid5: device sda4 operational as raid disk 0
[ 23.786935] raid5: device sdd4 operational as raid disk 3
[ 23.793198] raid5: device sdc4 operational as raid disk 2
[ 23.799451] raid5: device sdb4 operational as raid disk 1
[ 23.806115] raid5: allocated 4270kB for md3
[ 23.810973] raid5: raid level 5 set md3 active with 4 out of 4 devices, algorithm 2
[ 23.819860] RAID5 conf printout:
[ 23.823599] --- rd:4 wd:4 fd:0
[ 23.827238] disk 0, o:1, dev:sda4
[ 23.831179] disk 1, o:1, dev:sdb4
[ 23.835121] disk 2, o:1, dev:sdc4
[ 23.839074] disk 3, o:1, dev:sdd4
[ 23.843036] ....<6>md: syncing RAID array md3
[ 23.848123] md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc.
[ 23.856300] md: using maximum available idle IO bandwith (but not more than 200000 KB/sec) for reconstruction.
[ 23.867911] md: using 128k window, over a total of 67657664 blocks.
mdadm: /dev/md3 has been started with 4 drives.
Done.
Begin: Running /scripts/local-premount ..[ 23.902163] Attempting manual resume
.
[ 23.910134] swsusp: Suspend partition has wrong signature?
Done.
LinuxBIOS-1.1.8_s2881_Fallback Tue Jan 3 17:36:16 EST 2006 starting...
(0,1) link=00
(1,0) link=00
02 nodes initialized.
core0: --- { APICID = 02 NODEID = 01 COREID = 00} ---
SBLink=02
NC node|link=02
More information about the coreboot
mailing list