[coreboot-gerrit] Change in coreboot[master]: google/Bruce: Add Raydium touch screen support
Pan Sheng-Liang (Code Review)
gerrit at coreboot.org
Mon Aug 28 10:55:42 CEST 2017
Pan Sheng-Liang has uploaded this change for review. ( https://review.coreboot.org/21232
Change subject: google/Bruce: Add Raydium touch screen support
......................................................................
google/Bruce: Add Raydium touch screen support
Current coreboot does not create ACPI device for OS to recognize Raydium
touchscreen.
List the touch screen in the devicetree so that the correct ACPI device
are created.
BUG=b:64705535
BRANCH=master
TEST=emerge-coral coreboot
Change-Id: I91c58f59b94c84383d4a8afdfec95746adc69c73
Signed-off-by: Pan Sheng-Liang <Sheng-Liang.Pan at quantatw.com>
---
A src/mainboard/google/reef/variants/coral/devicetree.cb
1 file changed, 238 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/32/21232/1
diff --git a/src/mainboard/google/reef/variants/coral/devicetree.cb b/src/mainboard/google/reef/variants/coral/devicetree.cb
new file mode 100644
index 0000000..820f0eb
--- /dev/null
+++ b/src/mainboard/google/reef/variants/coral/devicetree.cb
@@ -0,0 +1,238 @@
+chip soc/intel/apollolake
+
+ device cpu_cluster 0 on
+ device lapic 0 on end
+ end
+
+ register "pcie_rp0_clkreq_pin" = "0" # wifi/bt
+ # Disable unused clkreq of PCIe root ports
+ register "pcie_rp1_clkreq_pin" = "CLKREQ_DISABLED"
+ register "pcie_rp2_clkreq_pin" = "CLKREQ_DISABLED"
+ register "pcie_rp3_clkreq_pin" = "CLKREQ_DISABLED"
+ register "pcie_rp4_clkreq_pin" = "CLKREQ_DISABLED"
+ register "pcie_rp5_clkreq_pin" = "CLKREQ_DISABLED"
+
+ # GPIO for PERST_0
+ # If the Board has PERST_0 signal, assign the GPIO
+ # If the Board does not have PERST_0, assign GPIO_PRT0_UDEF
+ register "prt0_gpio" = "GPIO_122"
+
+ # GPIO for SD card detect
+ register "sdcard_cd_gpio" = "GPIO_177"
+
+ # EMMC TX DATA Delay 1
+ # Refer to EDS-Vol2-22.3.
+ # [14:8] steps of delay for HS400, each 125ps.
+ # [6:0] steps of delay for SDR104/HS200, each 125ps.
+ register "emmc_tx_data_cntl1" = "0x0C16"
+
+ # EMMC TX DATA Delay 2
+ # Refer to EDS-Vol2-22.3.
+ # [30:24] steps of delay for SDR50, each 125ps.
+ # [22:16] steps of delay for DDR50, each 125ps.
+ # [14:8] steps of delay for SDR25/HS50, each 125ps.
+ # [6:0] steps of delay for SDR12, each 125ps.
+ register "emmc_tx_data_cntl2" = "0x28162828"
+
+ # EMMC RX CMD/DATA Delay 1
+ # Refer to EDS-Vol2-22.3.
+ # [30:24] steps of delay for SDR50, each 125ps.
+ # [22:16] steps of delay for DDR50, each 125ps.
+ # [14:8] steps of delay for SDR25/HS50, each 125ps.
+ # [6:0] steps of delay for SDR12, each 125ps.
+ register "emmc_rx_cmd_data_cntl1" = "0x00181717"
+
+ # EMMC RX CMD/DATA Delay 2
+ # Refer to EDS-Vol2-22.3.
+ # [17:16] stands for Rx Clock before Output Buffer
+ # [14:8] steps of delay for Auto Tuning Mode, each 125ps.
+ # [6:0] steps of delay for HS200, each 125ps.
+ register "emmc_rx_cmd_data_cntl2" = "0x10008"
+
+ # Enable DPTF
+ register "dptf_enable" = "1"
+
+ # PL1 override 12000 mW: the energy calculation is wrong with the
+ # current VR solution. Experiments show that SoC TDP max (6W) can
+ # be reached when RAPL PL1 is set to 12W.
+ register "tdp_pl1_override_mw" = "12000"
+ # Set RAPL PL2 to 15W.
+ register "tdp_pl2_override_mw" = "15000"
+
+ # Enable Audio Clock and Power gating
+ register "hdaudio_clk_gate_enable" = "1"
+ register "hdaudio_pwr_gate_enable" = "1"
+ register "hdaudio_bios_config_lockdown" = "1"
+
+ # Enable lpss s0ix
+ register "lpss_s0ix_enable" = "1"
+
+ # GPE configuration
+ # Note that GPE events called out in ASL code rely on this
+ # route, i.e., if this route changes then the affected GPE
+ # offset bits also need to be changed. This sets the PMC register
+ # GPE_CFG fields.
+ register "gpe0_dw1" = "PMC_GPE_N_31_0"
+ register "gpe0_dw2" = "PMC_GPE_N_63_32"
+ register "gpe0_dw3" = "PMC_GPE_SW_31_0"
+
+ # Enable I2C0 for audio codec at 400kHz
+ register "i2c[0]" = "{
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 104,
+ .fall_time_ns = 52,
+ }"
+
+ # Enable I2C2 bus early for TPM at 400kHz
+ register "i2c[2]" = "{
+ .early_init = 1,
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 57,
+ .fall_time_ns = 28,
+ }"
+
+ # touchscreen at 400kHz
+ register "i2c[3]" = "{
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 76,
+ .fall_time_ns = 164,
+ }"
+
+ # trackpad at 400kHz
+ register "i2c[4]" = "{
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 114,
+ .fall_time_ns = 164,
+ .data_hold_time_ns = 350,
+ }"
+
+ # digitizer at 400kHz
+ register "i2c[5]" = "{
+ .speed = I2C_SPEED_FAST,
+ .rise_time_ns = 152,
+ .fall_time_ns = 30,
+ }"
+
+ # Minimum SLP S3 assertion width 28ms.
+ register "slp_s3_assertion_width_usecs" = "28000"
+
+ device domain 0 on
+ device pci 00.0 on end # - Host Bridge
+ device pci 00.1 on end # - DPTF
+ device pci 00.2 on end # - NPK
+ device pci 02.0 on end # - Gen
+ device pci 03.0 on end # - Iunit
+ device pci 0d.0 on end # - P2SB
+ device pci 0d.1 on end # - PMC
+ device pci 0d.2 on end # - SPI
+ device pci 0d.3 on end # - Shared SRAM
+ device pci 0e.0 on # - Audio
+ chip drivers/generic/max98357a
+ register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_76)"
+ register "sdmode_delay" = "5"
+ device generic 0 on end
+ end
+ end
+ device pci 11.0 off end # - ISH
+ device pci 12.0 off end # - SATA
+ device pci 13.0 off end # - Root Port 2 - PCIe-A 0
+ device pci 13.1 off end # - Root Port 3 - PCIe-A 1
+ device pci 13.2 off end # - Root Port 4 - PCIe-A 2
+ device pci 13.3 off end # - Root Port 5 - PCIe-A 3
+ device pci 14.0 on
+ chip drivers/intel/wifi
+ register "wake" = "GPE0_DW3_00"
+ device pci 00.0 on end
+ end
+ end # - Root Port 0 - PCIe-B 0 - Wifi
+ device pci 14.1 off end # - Root Port 1 - PCIe-B 1
+ device pci 15.0 on end # - XHCI
+ device pci 15.1 off end # - XDCI
+ device pci 16.0 on # - I2C 0
+ chip drivers/i2c/da7219
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_116_IRQ)"
+ register "btn_cfg" = "50"
+ register "mic_det_thr" = "500"
+ register "jack_ins_deb" = "20"
+ register "jack_det_rate" = ""32ms_64ms""
+ register "jack_rem_deb" = "1"
+ register "a_d_btn_thr" = "0xa"
+ register "d_b_btn_thr" = "0x16"
+ register "b_c_btn_thr" = "0x21"
+ register "c_mic_btn_thr" = "0x3e"
+ register "btn_avg" = "4"
+ register "adc_1bit_rpt" = "1"
+ register "micbias_lvl" = "2600"
+ register "mic_amp_in_sel" = ""diff""
+ device i2c 1a on end
+ end
+ end
+ device pci 16.1 on end # - I2C 1
+ device pci 16.2 on
+ chip drivers/i2c/tpm
+ register "hid" = ""GOOG0005""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_28_IRQ)"
+ device i2c 50 on end
+ end
+ end # - I2C 2
+ device pci 16.3 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0001""
+ register "desc" = ""ELAN Touchscreen""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_21_IRQ)"
+ register "probed" = "1"
+ register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_36)"
+ register "reset_delay_ms" = "20"
+ register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPIO_152)"
+ register "enable_delay_ms" = "1"
+ register "has_power_resource" = "1"
+ device i2c 10 on end
+ end
+ end # - I2C 3
+ device pci 17.0 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_18_IRQ)"
+ register "wake" = "GPE0_DW1_15"
+ register "probed" = "1"
+ device i2c 15 on end
+ end
+ chip drivers/i2c/generic
+ register "hid" = ""RAYD0001""
+ register "desc" = ""Raydium Touchscreen""
+ register "irq" = "ACPI_IRQ_EDGE_LOW(GPIO_21_IRQ)"
+ register "probed" = "1"
+ device i2c 39 on end
+ end
+ end # - I2C 4
+ device pci 17.1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""WCOM50C1""
+ register "generic.desc" = ""WCOM Digitizer""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPIO_13_IRQ)"
+ register "hid_desc_reg_offset" = "0x1"
+ device i2c 0x9 on end
+ end
+ end # - I2C 5
+ device pci 17.2 off end # - I2C 6
+ device pci 17.3 off end # - I2C 7
+ device pci 18.0 on end # - UART 0
+ device pci 18.1 on end # - UART 1
+ device pci 18.2 on end # - UART 2
+ device pci 18.3 off end # - UART 3
+ device pci 19.0 on end # - SPI 0
+ device pci 19.1 off end # - SPI 1
+ device pci 19.2 off end # - SPI 2
+ device pci 1a.0 on end # - PWM
+ device pci 1b.0 on end # - SDCARD
+ device pci 1c.0 on end # - eMMC
+ device pci 1e.0 off end # - SDIO
+ device pci 1f.0 on # - LPC
+ chip ec/google/chromeec
+ device pnp 0c09.0 on end
+ end
+ end
+ device pci 1f.1 on end # - SMBUS
+ end
+end
--
To view, visit https://review.coreboot.org/21232
To unsubscribe, visit https://review.coreboot.org/settings
Gerrit-Project: coreboot
Gerrit-Branch: master
Gerrit-MessageType: newchange
Gerrit-Change-Id: I91c58f59b94c84383d4a8afdfec95746adc69c73
Gerrit-Change-Number: 21232
Gerrit-PatchSet: 1
Gerrit-Owner: Pan Sheng-Liang <sl.pan.quantw at gmail.com>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mail.coreboot.org/pipermail/coreboot-gerrit/attachments/20170828/b3ca6810/attachment.html>
More information about the coreboot-gerrit
mailing list