[coreboot-gerrit] Patch set updated for coreboot: src/southbridge/amd/sb700: Reset SATA controller in AHCI mode during startup

[Timothy Pearson (tpearson@raptorengineeringinc.com)]

Timothy Pearson (tpearson at raptorengineeringinc.com) just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/11998

-gerrit

commit 189e164df44bb447d5d0bcbf7c1d9e4450ba2e7c
Author: Timothy Pearson <tpearson at raptorengineeringinc.com>
Date:   Sun Jun 21 16:27:03 2015 -0500

    src/southbridge/amd/sb700: Reset SATA controller in AHCI mode during startup
    
    In AHCI mode SeaBIOS randomly fails to detect disks (AHCI timeouts),
    with the probability of a failure increasing with the number of disks
    connected to the controller.  Resetting the SATA controller appears to
    show the true state of the underlying hardware, allowing the drive
    detection code to attempt link renegotiation as needed.
    
    Change-Id: Ib1f7c5f830a0cdba41cb6f5b05d759adee5ce369
    Signed-off-by: Timothy Pearson <tpearson at raptorengineeringinc.com>
---
 src/southbridge/amd/sb700/sata.c | 47 ++++++++++++++++++++++++++++++----------
 1 file changed, 35 insertions(+), 12 deletions(-)

diff --git a/src/southbridge/amd/sb700/sata.c b/src/southbridge/amd/sb700/sata.c
index 6afdfdf..9f610a4 100644
--- a/src/southbridge/amd/sb700/sata.c
+++ b/src/southbridge/amd/sb700/sata.c
@@ -135,6 +135,8 @@ static void sata_init(struct device *dev)
 	/* get rev_id */
 	rev_id = pci_read_config8(sm_dev, 0x08) - 0x28;
 
+	printk(BIOS_SPEW, "rev_id=%x\n", rev_id);
+
 	if (sata_ahci_mode) {
 		/* Enable link latency enhancement on A14 and above */
 		if (rev_id >= 0x14) {
@@ -245,6 +247,27 @@ static void sata_init(struct device *dev)
 		write32(sata_bar5 + 0xfc, dword);
 	}
 
+	if (sata_ahci_mode) {
+		/* FIXME
+		* SeaBIOS does not know how to spin
+		* up the drives and therefore hangs
+		* in AHCI init if this is enabled...
+		*/
+		/* Enable staggered spin-up */
+		dword = read32(sata_bar5 + 0x00);
+#if 0
+		dword |= 0x1 << 27;
+#else
+		dword &= ~(0x1 << 27);
+#endif
+		write32(sata_bar5 + 0x00, dword);
+	
+		/* Reset the HBA to avoid stuck drives in SeaBIOS */
+		dword = read32(sata_bar5 + 0x04);
+		dword |= 0x1;
+		write32(sata_bar5 + 0x04, dword);
+	}
+
 	/* Write protect Sub-Class Code */
 	byte = pci_read_config8(dev, 0x40);
 	byte &= ~(1 << 0);
@@ -371,21 +394,21 @@ static void sata_init(struct device *dev)
 	}
 
 	/* Below is CIM InitSataLateFar */
-	/* Enable interrupts from the HBA  */
-	byte = read8(sata_bar5 + 0x4);
-	byte |= 1 << 1;
-	write8((sata_bar5 + 0x4), byte);
-
 	if (!sata_ahci_mode) {
-		/* Clear error status */
-		write32((sata_bar5 + 0x130), 0xFFFFFFFF);
-		write32((sata_bar5 + 0x1b0), 0xFFFFFFFF);
-		write32((sata_bar5 + 0x230), 0xFFFFFFFF);
-		write32((sata_bar5 + 0x2b0), 0xFFFFFFFF);
-		write32((sata_bar5 + 0x330), 0xFFFFFFFF);
-		write32((sata_bar5 + 0x3b0), 0xFFFFFFFF);
+		/* Enable interrupts from the HBA  */
+		byte = read8(sata_bar5 + 0x4);
+		byte |= 1 << 1;
+		write8((sata_bar5 + 0x4), byte);
 	}
 
+	/* Clear error status */
+	write32((sata_bar5 + 0x130), 0xFFFFFFFF);
+	write32((sata_bar5 + 0x1b0), 0xFFFFFFFF);
+	write32((sata_bar5 + 0x230), 0xFFFFFFFF);
+	write32((sata_bar5 + 0x2b0), 0xFFFFFFFF);
+	write32((sata_bar5 + 0x330), 0xFFFFFFFF);
+	write32((sata_bar5 + 0x3b0), 0xFFFFFFFF);
+
 	/* Clear SATA status,Firstly we get the AcpiGpe0BlkAddr */
 	/* ????? why CIM does not set the AcpiGpe0BlkAddr , but use it??? */