Hi,
tried several Tyan 2915 (S2915A2NRF) and S2915-E (S2915A2NRF-E) all with the same result. #1 Using flashrom -r to get the PROM's content and comparing that with the appropriate version from Tyan's website gives differences in all cases. #2 Took a 2915 (S2915A2NRF) and flashed with the DOS tool offered by Tyan (phlash16.exe) to BIOS revision 3.00 (2915v300.rom). Then reread with flashrom -r and compared both files - a bunch of differencies again. I attached the outputs of flashrom, lspci, and superiotool for this board.
Regards, Axel
// ----- * flashrom -V flashrom v0.9.2-r1096 on Linux 2.6.23.13-SMP64 (x86_64), built with libpci 2.2.9, GCC 4.2.3, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 931M loops per second, 10 myus = 11 us, 100 myus = 110 us, 1000 myus = 1058 us, 10000 myus = 9993 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Tyan Computer Corporation " DMI string system-product-name: "MCP55 " DMI string system-version: "REFERENCE" DMI string baseboard-manufacturer: "Tyan Computer Corporation " DMI string baseboard-product-name: "S2915 " DMI string baseboard-version: "REFERENCE" DMI string chassis-type: "Main Server Chassis" Found chipset "NVIDIA MCP55", enabling flash write... chipset PCI ID is 10de:0364, OK. This chipset supports the following protocols: Non-SPI. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT25DF021, 256 KB: skipped. Probing for Atmel AT25DF041A, 512 KB: skipped. Probing for Atmel AT25DF081, 1024 KB: skipped. Probing for Atmel AT25DF161, 2048 KB: skipped. Probing for Atmel AT25DF321, 4096 KB: skipped. Probing for Atmel AT25DF321A, 4096 KB: skipped. Probing for Atmel AT25DF641, 8192 KB: skipped. Probing for Atmel AT25F512B, 64 KB: skipped. Probing for Atmel AT25FS010, 128 KB: skipped. Probing for Atmel AT25FS040, 512 KB: skipped. Probing for Atmel AT26DF041, 512 KB: skipped. Probing for Atmel AT26DF081A, 1024 KB: skipped. Probing for Atmel AT26DF161, 2048 KB: skipped. Probing for Atmel AT26DF161A, 2048 KB: skipped. Probing for Atmel AT26F004, 512 KB: skipped. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT45CS1282, 16896 KB: skipped. Probing for Atmel AT45DB011D, 128 KB: skipped. Probing for Atmel AT45DB021D, 256 KB: skipped. Probing for Atmel AT45DB041D, 512 KB: skipped. Probing for Atmel AT45DB081D, 1024 KB: skipped. Probing for Atmel AT45DB161D, 2048 KB: skipped. Probing for Atmel AT45DB321C, 4224 KB: skipped. Probing for Atmel AT45DB321D, 4096 KB: skipped. Probing for Atmel AT45DB642D, 8192 KB: skipped. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT49F020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for AMIC A25L05PT, 64 KB: skipped. Probing for AMIC A25L05PU, 64 KB: skipped. Probing for AMIC A25L10PT, 128 KB: skipped. Probing for AMIC A25L10PU, 128 KB: skipped. Probing for AMIC A25L20PT, 256 KB: skipped. Probing for AMIC A25L20PU, 256 KB: skipped. Probing for AMIC A25L40PT, 512 KB: skipped. Probing for AMIC A25L40PU, 512 KB: skipped. Probing for AMIC A25L80P, 1024 KB: skipped. Probing for AMIC A25L16PT, 2048 KB: skipped. Probing for AMIC A25L16PU, 2048 KB: skipped. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for EMST F25L008A, 1024 KB: skipped. Probing for Eon EN25B05, 64 KB: skipped. Probing for Eon EN25B05T, 64 KB: skipped. Probing for Eon EN25B10, 128 KB: skipped. Probing for Eon EN25B10T, 128 KB: skipped. Probing for Eon EN25B20, 256 KB: skipped. Probing for Eon EN25B20T, 256 KB: skipped. Probing for Eon EN25B40, 512 KB: skipped. Probing for Eon EN25B40T, 512 KB: skipped. Probing for Eon EN25B80, 1024 KB: skipped. Probing for Eon EN25B80T, 1024 KB: skipped. Probing for Eon EN25B16, 2048 KB: skipped. Probing for Eon EN25B16T, 2048 KB: skipped. Probing for Eon EN25B32, 4096 KB: skipped. Probing for Eon EN25B32T, 4096 KB: skipped. Probing for Eon EN25B64, 8192 KB: skipped. Probing for Eon EN25B64T, 8192 KB: skipped. Probing for Eon EN25D16, 2048 KB: skipped. Probing for Eon EN25F05, 64 KB: skipped. Probing for Eon EN25F10, 128 KB: skipped. Probing for Eon EN25F20, 256 KB: skipped. Probing for Eon EN25F40, 512 KB: skipped. Probing for Eon EN25F80, 1024 KB: skipped. Probing for Eon EN25F16, 2048 KB: skipped. Probing for Eon EN25F32, 4096 KB: skipped. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for Hyundai HY29F002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Hyundai HY29F002B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004BV/BE-B, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004BV/BE-T, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/CV/CE-B, 512 KB: probe_82802ab: id1 0x4e, id2 0x50, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/CV/CE-T, 512 KB: probe_82802ab: id1 0x4e, id2 0x50, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: skipped. Probing for Macronix MX25L1005, 128 KB: skipped. Probing for Macronix MX25L2005, 256 KB: skipped. Probing for Macronix MX25L4005, 512 KB: skipped. Probing for Macronix MX25L8005, 1024 KB: skipped. Probing for Macronix MX25L1605, 2048 KB: skipped. Probing for Macronix MX25L1635D, 2048 KB: skipped. Probing for Macronix MX25L3205, 4096 KB: skipped. Probing for Macronix MX25L3235D, 4096 KB: skipped. Probing for Macronix MX25L6405, 8192 KB: skipped. Probing for Macronix MX25L12805, 16384 KB: skipped. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Probing for Numonyx M25PE20, 256 KB: skipped. Probing for Numonyx M25PE40, 512 KB: skipped. Probing for Numonyx M25PE80, 1024 KB: skipped. Probing for Numonyx M25PE16, 2048 KB: skipped. Probing for PMC Pm25LV010, 128 KB: skipped. Probing for PMC Pm25LV016B, 2048 KB: skipped. Probing for PMC Pm25LV020, 256 KB: skipped. Probing for PMC Pm25LV040, 512 KB: skipped. Probing for PMC Pm25LV080B, 1024 KB: skipped. Probing for PMC Pm25LV512, 64 KB: skipped. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Sanyo LF25FW203A, 2048 KB: skipped. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: skipped. Probing for Spansion S25FL016A, 2048 KB: skipped. Probing for SST SST25VF016B, 2048 KB: skipped. Probing for SST SST25VF032B, 4096 KB: skipped. Probing for SST SST25VF064C, 8192 KB: skipped. Probing for SST SST25VF040.REMS, 512 KB: skipped. Probing for SST SST25VF040B, 512 KB: skipped. Probing for SST SST25LF040A.RES, 512 KB: skipped. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Probing for SST SST25VF080B, 1024 KB: skipped. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Found chip "SST SST49LF080A" (1024 KB, LPC) at physical address 0xfff00000. Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: skipped. Probing for ST M25P05.RES, 64 KB: skipped. Probing for ST M25P10-A, 128 KB: skipped. Probing for ST M25P10.RES, 128 KB: skipped. Probing for ST M25P20, 256 KB: skipped. Probing for ST M25P40, 512 KB: skipped. Probing for ST M25P40-old, 512 KB: skipped. Probing for ST M25P80, 1024 KB: skipped. Probing for ST M25P16, 2048 KB: skipped. Probing for ST M25P32, 4096 KB: skipped. Probing for ST M25P64, 8192 KB: skipped. Probing for ST M25P128, 16384 KB: skipped. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0x4e, id2 0x50 Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0x70, id2 0x00, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0x0a, id2 0xc0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x4e, id2 0x41, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25Q80, 1024 KB: skipped. Probing for Winbond W25Q16, 2048 KB: skipped. Probing for Winbond W25Q32, 4096 KB: skipped. Probing for Winbond W25Q64, 8192 KB: skipped. Probing for Winbond W25x10, 128 KB: skipped. Probing for Winbond W25x20, 256 KB: skipped. Probing for Winbond W25x40, 512 KB: skipped. Probing for Winbond W25x80, 1024 KB: skipped. Probing for Winbond W25x16, 2048 KB: skipped. Probing for Winbond W25x32, 4096 KB: skipped. Probing for Winbond W25x64, 8192 KB: skipped. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49F020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x5b Probing for AMIC unknown AMIC SPI chip, 0 KB: skipped. Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Probing for EON unknown EON SPI chip, 0 KB: skipped. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Probing for SST unknown SST SPI chip, 0 KB: skipped. Probing for ST unknown ST SPI chip, 0 KB: skipped. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. No operations were specified.
* lspci -nnvvxxx 00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller [10de:0369] (rev a2) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 69 03 06 00 b0 00 a2 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 40: f1 10 15 29 08 dc e0 01 22 00 11 11 d0 00 00 00 50: 23 06 7f 00 03 00 00 00 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 0a 00 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00 80: 23 99 88 00 fa 00 64 0e 02 00 00 00 7f 00 00 00 90: 70 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 02 00 00 00 00 00 00 00 00 00 00 00 80 00 0f 0f d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8 e0: 00 00 e0 fe 00 00 00 00 00 00 80 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0364] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: I/O ports at 1c00 [size=128] 00: de 10 64 03 0f 00 a0 00 a3 00 01 06 00 00 80 00 10: 01 1c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: f1 10 15 29 00 00 d0 fe fa 3e ff 00 fa 3e ff 00 50: fa 3e ff 00 00 5a 62 02 00 00 00 01 00 00 ff ff 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 f9 ff 70: 10 00 ff ff c5 80 00 00 00 00 44 19 03 80 20 10 80: 09 b0 00 c6 da 12 00 40 ff 00 00 00 ff 00 00 00 90: ff 7f 00 00 00 00 00 00 21 47 95 86 ef cd ab 00 a0: 03 00 10 11 00 38 00 00 00 06 8f 06 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 1d 00 fc fd 03 00 30 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 255 Region 0: I/O ports at 2000 [size=64] Region 4: I/O ports at 2440 [size=64] Region 5: I/O ports at 2400 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus 00: de 10 68 03 01 00 b0 00 a3 00 05 0c 00 00 80 00 10: 01 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 41 24 00 00 01 24 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 01 00 00 40: f1 10 15 29 01 00 02 c0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 10 00 00 01 14 00 00 01 18 00 00 00 00 00 00 70: 01 00 00 00 00 00 04 a0 00 00 00 00 01 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: d4 30 80 00 01 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 64 15 05 00 a5 21 50 03 80 30 80 00 77 44 44 11 f0: 5a ff 5f 3f 00 00 00 c0 10 00 00 00 00 00 00 00
00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036c] (rev a1) (prog-if 10 [OHCI]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 10 Region 0: Memory at a0004000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ohci_hcd 00: de 10 6c 03 07 00 b0 00 a1 10 03 0c 00 00 80 00 10: 00 40 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01 40: f1 10 15 29 01 00 02 fe 00 00 00 00 00 00 00 00 50: c0 00 00 00 1d 47 40 00 10 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller [10de:036d] (rev a2) (prog-if 20 [EHCI]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 11 Region 0: Memory at a0005000 (32-bit, non-prefetchable) [size=256] Capabilities: [44] Debug port: BAR=1 offset=0098 Capabilities: [80] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: ehci_hcd 00: de 10 6d 03 06 00 b0 00 a2 20 03 0c 00 00 80 00 10: 00 50 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 02 03 01 40: f1 10 15 29 0a 80 98 20 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 20 20 01 00 00 60 18 85 03 3c 3f 01 00 00 00 00 70: 00 00 08 00 00 10 20 80 89 3d b6 22 77 25 04 00 80: 01 00 02 fe 00 00 00 00 00 00 00 00 15 16 00 00 90: 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 01 00 00 01 00 00 08 80 00 00 00 00 00 00 00 00 b0: 22 11 00 33 44 00 00 00 ff 03 00 00 00 00 00 00 c0: 10 10 2d 0d 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e] (rev a1) (prog-if 8a [Master SecP PriP]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1] Region 4: I/O ports at 2480 [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: AMD_IDE 00: de 10 6e 03 05 00 b0 00 a1 8a 01 01 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 81 24 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 03 01 40: f1 10 15 29 01 00 02 00 00 00 00 00 00 00 00 00 50: 02 f0 00 00 00 00 00 00 a8 a8 a8 20 2f 00 ff 20 60: 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 01 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 12 00 00 00 00 00 00 00
00:05.0 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 19 Region 0: I/O ports at 24d0 [size=8] Region 1: I/O ports at 24c4 [size=4] Region 2: I/O ports at 24c8 [size=8] Region 3: I/O ports at 24c0 [size=4] Region 4: I/O ports at 2490 [size=16] Region 5: Memory at a0006000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: sata_nv 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00 10: d1 24 00 00 c5 24 00 00 c9 24 00 00 c1 24 00 00 20: 91 24 00 00 00 60 00 a0 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 07 01 03 01 40: f1 10 15 29 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0b 68 08 80 00 00 00 00 00 1d 00 00 00 60 09 00 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 80 80: 00 00 00 00 5f de ff fb 00 00 c8 10 ff 7b ff ff 90: 00 00 bf 3d 00 00 00 00 06 00 06 10 7f 03 01 01 a0: 12 0a 00 00 40 00 00 00 00 00 00 00 23 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 03 a8 d0: 0a 00 02 03 42 00 00 00 00 00 00 00 00 10 80 00 e0: 0a 00 02 03 42 00 00 00 00 00 00 00 0f 00 70 00 f0: 00 00 00 00 00 00 00 00 12 00 0c 00 00 00 00 00
00:05.1 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin B routed to IRQ 18 Region 0: I/O ports at 24e8 [size=8] Region 1: I/O ports at 24dc [size=4] Region 2: I/O ports at 24e0 [size=8] Region 3: I/O ports at 24d8 [size=4] Region 4: I/O ports at 24a0 [size=16] Region 5: Memory at a0007000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: sata_nv 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00 10: e9 24 00 00 dd 24 00 00 e1 24 00 00 d9 24 00 00 20: a1 24 00 00 00 70 00 a0 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 05 02 03 01 40: f1 10 15 29 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0b 68 08 80 00 00 00 00 00 1d 00 00 00 60 09 00 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 80 80: 00 00 00 00 ff 3f ff f7 00 00 eb 1c cf ff ff ff 90: 00 00 55 3f 00 00 00 00 06 00 06 10 7f 03 01 01 a0: 12 0a 00 00 40 00 00 00 00 00 00 00 33 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 03 a8 d0: 0a 00 02 03 42 00 00 00 00 00 00 00 00 48 20 01 e0: 0a 00 02 03 42 00 00 00 00 00 00 00 0f 00 20 00 f0: 00 00 00 00 00 00 00 00 10 00 0c 00 00 00 00 00
00:05.2 IDE interface [0101]: nVidia Corporation MCP55 SATA Controller [10de:037f] (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (750ns min, 250ns max) Interrupt: pin C routed to IRQ 17 Region 0: I/O ports at 2800 [size=8] Region 1: I/O ports at 24f4 [size=4] Region 2: I/O ports at 24f8 [size=8] Region 3: I/O ports at 24f0 [size=4] Region 4: I/O ports at 24b0 [size=16] Region 5: Memory at a0008000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: sata_nv 00: de 10 7f 03 07 00 b0 00 a3 85 01 01 00 00 80 00 10: 01 28 00 00 f5 24 00 00 f9 24 00 00 f1 24 00 00 20: b1 24 00 00 00 80 00 a0 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 03 03 01 40: f1 10 15 29 01 b0 02 00 00 00 00 00 00 00 00 00 50: 0b 68 08 80 00 00 00 00 00 1d 00 00 00 60 09 00 60: 00 00 00 00 41 0c 00 00 00 0f 06 42 00 00 00 00 70: 2c 78 c4 40 01 10 00 00 01 10 00 00 20 00 20 80 80: 00 00 00 00 ed fe eb ff 00 00 9f 1a 6e ff 9f ff 90: 00 00 c6 2f 00 00 00 00 06 00 06 10 7f 03 01 01 a0: 12 0a 00 00 40 00 00 00 00 00 00 00 33 31 00 02 b0: 05 cc 84 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 0a 00 0a 00 08 00 03 a8 d0: 0a 00 02 03 42 00 00 00 00 00 00 00 00 00 00 00 e0: 0a 00 02 03 42 00 00 00 00 00 00 00 00 00 a0 00 f0: 00 00 00 00 00 00 00 00 10 00 0c 00 00 00 00 00
00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370] (rev a2) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 Memory behind bridge: a0100000-a01fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn+ Capabilities: [b8] Subsystem: nVidia Corporation Unknown device [10de:cb84] Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 00: de 10 70 03 07 01 b0 00 a2 01 04 06 00 00 81 00 10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 80 02 20: 10 a0 10 a0 f0 ff 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 b8 00 00 00 00 00 00 00 ff 00 04 0a 40: 00 00 33 07 01 00 02 00 05 00 00 00 00 00 48 00 50: 00 00 fe 9b 00 00 00 00 ff 1f ff 1f 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 fe 63 02 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 a8 90: 00 00 e0 fe 00 00 00 00 00 00 00 00 00 00 00 00 a0: 04 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 ff ff 00 00 0d 8c 00 00 de 10 84 cb c0: de 10 84 cb 03 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:06.1 Audio device [0403]: nVidia Corporation MCP55 High Definition Audio [10de:0371] (rev a2) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin B routed to IRQ 23 Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00: de 10 71 03 06 00 b0 00 a2 00 03 04 00 00 80 00 10: 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 02 02 05 40: f1 10 15 29 01 50 02 c0 00 00 00 00 01 01 0f 00 50: 05 6c 80 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 0f 00 00 00 08 00 03 a8 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 47 10 29 00 00 00 00 00 00
00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 1273 Region 0: Memory at a0009000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2808 [size=8] Region 2: Memory at a0005800 (32-bit, non-prefetchable) [size=256] Region 3: Memory at a0005400 (32-bit, non-prefetchable) [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable+ DSel=0 DScale=0 PME- Capabilities: [70] MSI-X: Enable- Mask- TabSize=8 Vector table: BAR=2 offset=00000000 PBA: BAR=3 offset=00000000 Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable+ Address: 00000000fee0f00c Data: 41b9 Masking: 000000fe Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: forcedeth 00: de 10 73 03 07 04 b0 00 a3 00 80 06 00 00 00 00 10: 00 90 00 a0 09 28 00 00 00 58 00 a0 00 54 00 a0 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 01 14 40: f1 10 15 29 01 70 02 fe 00 01 00 00 0c 00 00 00 50: 05 6c 87 01 0c f0 e0 fe 00 00 00 00 b9 41 00 00 60: fe 00 00 00 00 00 00 00 ff 00 00 00 08 00 03 a8 70: 11 50 07 00 02 00 00 00 03 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 11 00 00 00 52 01 00 00 00 00 00 00
00:09.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (250ns min, 5000ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at a000b000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 2810 [size=8] Region 2: Memory at a000a000 (32-bit, non-prefetchable) [size=256] Region 3: Memory at a0005c00 (32-bit, non-prefetchable) [size=16] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [70] MSI-X: Enable- Mask- TabSize=8 Vector table: BAR=2 offset=00000000 PBA: BAR=3 offset=00000000 Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: forcedeth 00: de 10 73 03 07 00 b0 00 a3 00 80 06 00 00 00 00 10: 00 b0 00 a0 11 28 00 00 00 a0 00 a0 00 5c 00 a0 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 01 14 40: f1 10 15 29 01 70 02 fe 00 00 00 00 0c 00 00 00 50: 05 6c 86 01 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 ff 00 00 00 08 00 03 a8 70: 11 50 07 00 02 00 00 00 03 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 11 00 00 00 52 01 00 00 00 00 00 00
00:0a.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0376] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4151 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 76 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 51 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 81 3c 11 05 90: 00 00 81 10 00 00 00 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0378] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=03, subordinate=05, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: a0200000-a03fffff Prefetchable memory behind bridge: 00000000a4000000-00000000a40fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4159 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 78 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 03 05 00 31 31 00 00 20: 20 a0 30 a0 01 a4 01 a4 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 59 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 41 3c 11 02 90: 00 00 41 30 00 00 00 00 c0 01 48 01 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0377] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 I/O behind bridge: 00004000-00004fff Memory behind bridge: a1000000-a2ffffff Prefetchable memory behind bridge: 00000000b0000000-00000000bfffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4161 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock- Changed: MRL- PresDet+ LinkState+ RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 77 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 00 06 06 00 41 41 00 00 20: 00 a1 f0 a2 01 b0 f1 bf 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 0c 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 61 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 01 3d 11 00 90: 00 00 01 31 00 00 00 00 c0 01 48 01 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 Capabilities: [a0] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 Capabilities: [c0] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 01 01 03 00 02 04 01 00 01 01 01 00 01 01 01 00 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 60: 10 00 03 00 e4 02 00 00 20 c8 2e 0f 30 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 a0 01 21 20 00 11 11 22 06 75 80 02 00 00 00 90: 36 61 34 01 00 00 00 00 03 00 00 00 00 00 00 00 a0: 08 c0 01 21 20 00 11 11 22 06 75 80 02 00 00 00 b0: 01 0f 11 06 00 00 00 00 03 00 00 00 00 00 00 00 c0: 08 00 01 21 20 00 11 11 22 06 75 80 02 00 00 00 d0: 69 01 61 01 00 00 7f 00 07 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 63 01 03 00 64 01 01 00 63 02 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00 80: 03 00 a0 00 20 ff bf 00 00 00 00 00 00 00 00 00 90: 03 00 c0 00 01 ff cf 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 03 0a 00 00 20 0b 00 00 b0: 03 00 e0 00 a0 ff e7 00 03 00 e8 00 81 ff ef 00 c0: 33 10 00 00 20 40 00 00 03 50 00 00 01 50 00 00 d0: 00 00 00 00 00 00 00 00 03 f0 00 00 01 f0 00 00 e0: 03 02 00 7f 13 00 80 ff 44 00 ff e3 74 03 8f e0 f0: 01 64 00 9c 00 00 00 00 00 00 00 00 00 00 00 00
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 01 00 00 00 01 02 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 e0 3d f8 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00 80: 60 00 00 00 00 00 00 00 24 aa 67 ef 20 13 82 00 90: 10 28 00 00 6a 80 00 64 39 00 00 80 00 00 00 00 a0: eb 02 00 ef 00 00 00 00 00 00 00 00 00 00 00 00 b0: 27 6e 06 d6 a3 00 00 00 13 31 0e 3f e8 04 e0 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: f2 60 79 bf 32 b5 7f 1b 25 20 63 73 fa 26 6c d4 e0: fb 60 39 df 12 b9 fb 19 33 11 73 5b 7e 36 6c d4 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: ff 3b 04 00 40 00 10 0a 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 c0 f3 20 fe 60: 63 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00 80: 00 00 07 23 13 21 13 00 00 00 00 00 00 00 00 00 90: 03 00 00 00 4e 00 00 00 00 02 60 02 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 70 6c 1e c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 06 a7 e2 04 10 27 60 20 26 26 25 00 e0: 00 00 00 00 24 1b 66 00 1b 17 00 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 13 0f 04 00
00:19.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [80] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 Capabilities: [a0] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 Capabilities: [c0] HyperTransport: Host or Secondary Interface !!! Possibly incomplete decoding Command: WarmRst+ DblEnd- Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit Revision ID: 1.02 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00 40: 04 08 01 00 01 01 05 00 01 01 01 00 01 01 01 00 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00 60: 11 00 03 00 e4 00 00 00 20 c8 2e 0f 0c 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 08 a0 01 21 20 00 11 11 22 06 75 80 02 00 00 00 90: 6a 01 61 01 00 80 ff 00 07 00 00 00 00 00 00 00 a0: 08 c0 01 21 20 00 11 11 22 06 75 80 02 00 00 00 b0: 36 61 34 01 00 00 00 00 03 00 00 00 00 00 00 00 c0: 08 00 01 21 20 00 11 11 22 06 75 80 02 00 00 00 d0: 01 0f 11 06 00 00 00 00 03 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:19.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 03 00 00 00 00 00 63 01 03 00 64 01 01 00 63 02 50: 00 00 00 00 02 00 00 00 00 00 00 00 03 00 00 00 60: 00 00 00 00 04 00 00 00 00 00 00 00 05 00 00 00 70: 00 00 00 00 06 00 00 00 00 00 00 00 07 00 00 00 80: 03 00 a0 00 20 ff bf 00 00 00 00 00 00 00 00 00 90: 03 00 c0 00 01 ff cf 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 03 0a 00 00 20 0b 00 00 b0: 03 00 e0 00 a0 ff e7 00 03 00 e8 00 81 ff ef 00 c0: 33 10 00 00 20 40 00 00 03 50 00 00 01 50 00 00 d0: 00 00 00 00 00 00 00 00 03 f0 00 00 01 f0 00 00 e0: 03 02 00 7f 13 00 80 ff 44 00 ff e3 74 03 8f e0 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:19.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 40: 00 00 00 00 00 00 00 00 01 00 00 00 01 02 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 e0 3d f8 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 46 00 00 00 00 00 00 00 80: 60 00 00 00 00 00 00 00 24 aa 67 ef 20 13 82 00 90: 10 28 00 00 6a 80 00 64 39 00 00 80 00 00 00 00 a0: eb 02 00 ef 00 00 00 00 00 00 00 00 00 00 00 00 b0: 98 36 0d d6 a3 00 00 00 18 06 93 a9 ad 4f c0 70 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 8f fe ed 6e 00 99 91 09 a4 a5 87 9b 19 2c 48 11 e0: 56 df 6c e6 00 dd 88 09 b6 a5 c7 cf 15 0d 0c 11 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:19.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Capabilities: [f0] Secure device <?> Kernel driver in use: k8temp 00: 22 10 03 11 00 00 10 00 00 00 00 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 40: ff 3b 04 00 40 00 10 0a 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 60: ff 00 00 00 00 00 00 00 c0 00 00 00 00 00 00 00 70: 11 01 02 51 11 80 00 50 00 38 00 08 1a 22 00 00 80: 00 00 07 23 13 21 13 00 00 00 00 00 00 00 00 00 90: 03 00 00 00 4e 00 00 00 00 02 60 02 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 06 a7 e2 04 10 27 60 20 25 26 26 00 e0: 00 00 00 00 24 1b 66 00 1b 17 00 00 00 00 00 00 f0: 0f 00 10 00 00 00 00 00 00 00 00 00 13 0f 04 00
01:05.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI]) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at a0104000 (32-bit, non-prefetchable) [size=2K] Region 1: Memory at a0100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME+ Kernel driver in use: ohci1394 00: 4c 10 23 80 56 01 10 02 00 10 00 0c 10 40 00 00 10: 00 40 10 a0 00 00 10 a0 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 02 04 40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 88 00 00 00 f0: 10 00 00 00 82 10 00 00 f1 10 15 29 00 00 00 00
03:00.0 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [1033:0125] (rev 06) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=03, secondary=04, subordinate=04, sec-latency=68 I/O behind bridge: 00003000-00003fff Memory behind bridge: a0300000-a03fffff Prefetchable memory behind bridge: 00000000a4000000-00000000a40fffff Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <4us, L1 <16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [54] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz Status: Dev=03:00.0 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=32 CommitmentLimit=32 Downstream: Capacity=16 CommitmentLimit=16 Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [100] Advanced Error Reporting <?> 00: 33 10 25 01 47 01 10 00 06 00 04 06 10 00 81 00 10: 00 00 00 00 00 00 00 00 03 04 04 44 31 31 20 04 20: 30 a0 30 a0 01 a4 01 a4 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 10 54 71 00 01 00 00 00 00 20 0a 00 81 6c 02 00 50: 00 00 41 00 07 64 c3 00 00 03 00 00 20 00 20 00 60: 10 00 10 00 01 00 42 da 00 00 c0 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 1f 3f 00 00 00 00 90: 13 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
03:00.1 PCI bridge [0604]: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge [1033:0125] (rev 06) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Region 0: Memory at a0200000 (64-bit, non-prefetchable) [size=128] Bus: primary=03, secondary=05, subordinate=05, sec-latency=4 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Express (v1) PCI/PCI-X Bridge, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry- MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <4us, L1 <16us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- DLActive- BWMgmt- ABWMgmt- Capabilities: [54] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv Status: Dev=03:00.1 64bit- 133MHz- SCD- USC- SCO- SRD- Upstream: Capacity=32 CommitmentLimit=32 Downstream: Capacity=16 CommitmentLimit=16 Capabilities: [64] Power Management version 2 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=55mA PME(D0+,D1+,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Bridge: PM- B3+ Capabilities: [6c] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [7c] Hot-plug capable Capabilities: [100] Advanced Error Reporting <?> 00: 33 10 25 01 47 01 10 00 06 00 04 06 10 00 81 00 10: 04 00 20 a0 00 00 00 00 03 05 05 04 f1 01 20 24 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 04 00 40: 10 54 71 00 01 00 00 00 00 20 00 00 81 6c 02 00 50: 00 00 41 00 07 64 03 00 01 03 00 00 20 00 20 00 60: 10 00 10 00 01 6c 42 da 00 00 c0 00 05 7c 80 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 13 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
04:09.0 SCSI storage controller [0100]: Adaptec ASC-29320A U320 [9005:8000] (rev 10) Subsystem: Adaptec Unknown device [9005:0060] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (10000ns min, 6250ns max), Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 20 Region 0: I/O ports at 3400 [disabled] [size=256] Region 1: Memory at a0300000 (64-bit, non-prefetchable) [size=8K] Region 3: I/O ports at 3000 [disabled] [size=256] [virtual] Expansion ROM at a4000000 [disabled] [size=512K] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [94] PCI-X non-bridge device Command: DPERE- ERO+ RBC=512 OST=8 Status: Dev=04:09.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz- Kernel driver in use: aic79xx 00: 05 90 00 80 56 01 30 04 10 00 00 01 10 40 00 00 10: 01 34 00 00 04 00 30 a0 00 00 00 00 01 30 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 05 90 60 00 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 28 19 40: c6 83 00 80 01 00 00 00 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 07 00 42 00 48 04 03 06 00 00 00 00 a0: 05 94 82 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 a0 02 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 0c 00 00 00 00
06:00.0 VGA compatible controller [0300]: nVidia Corporation G71 [Quadro FX 1500] [10de:029e] (rev a1) (prog-if 00 [VGA controller]) Subsystem: nVidia Corporation Unknown device [10de:032c] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 22 Region 0: Memory at a2000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at b0000000 (64-bit, prefetchable) [size=256M] Region 3: Memory at a1000000 (64-bit, non-prefetchable) [size=16M] Region 5: I/O ports at 4000 [size=128] Capabilities: [60] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [78] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported- RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us ClockPM- Suprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100] Virtual Channel <?> Capabilities: [128] Power Budgeting <?> Kernel driver in use: nvidia Kernel modules: nvidia 00: de 10 9e 02 47 00 10 00 a1 00 00 03 00 00 00 00 10: 00 00 00 a2 0c 00 00 b0 00 00 00 00 04 00 00 a1 20: 00 00 00 00 01 40 00 00 00 00 00 00 de 10 2c 03 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 00 00 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 50: 01 00 00 00 01 00 00 00 ce d6 23 00 00 00 00 00 60: 01 68 02 00 00 00 00 00 05 78 80 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 10 00 01 00 00 05 00 00 80: 10 28 00 00 01 4d 01 00 08 00 01 11 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller [10de:0369] (rev a2) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: [44] HyperTransport: Slave or Primary Interface Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL- Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn- Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b- Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn- Revision ID: 1.03 Link Frequency 0: 1.0GHz Link Error 0: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend- Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD- Link Frequency 1: 200MHz Link Error 1: <Prot- <Ovfl- <EOC- CTLTm- Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend- Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE- Prefetchable memory behind bridge Upper: 00-00 Bus Number: 00 Capabilities: [dc] HyperTransport: MSI Mapping Enable+ Fixed- Mapping Address Base: 00000000fee00000 00: de 10 69 03 06 00 b0 00 a2 00 00 05 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 40: f1 10 15 29 08 dc e0 01 22 00 11 11 d0 00 00 00 50: 23 06 7f 00 03 00 00 00 00 00 03 00 00 00 00 00 60: 00 00 00 00 00 00 00 00 00 00 00 00 06 36 0a 00 70: 44 44 44 00 d0 09 00 00 11 00 00 00 11 11 88 00 80: 23 99 88 00 fa 00 64 0e 02 00 00 00 7f 00 00 00 90: 70 00 80 80 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 01 01 01 01 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 80 00 0f 0f d0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 01 a8 e0: 00 00 e0 fe 00 00 00 00 00 00 80 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80:01.0 RAM memory [0500]: nVidia Corporation MCP55 LPC Bridge [10de:0361] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: I/O ports at fc00 [size=128] Region 1: Memory at c0000000 (32-bit, non-prefetchable) [size=4K] 00: de 10 61 03 0f 00 a0 00 a3 00 00 05 00 00 80 00 10: 01 fc 00 00 00 00 00 c0 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00 40: f1 10 15 29 00 00 00 00 fa 3e ff 00 fa 3e ff 00 50: fa 3e ff 00 00 5a 62 02 00 00 00 01 00 00 ff ff 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f9 ff 70: 10 00 ff ff 43 00 00 00 00 00 42 20 00 00 00 00 80: 00 00 00 00 00 00 00 00 f0 00 00 01 80 00 00 00 90: 00 00 00 00 00 00 00 00 21 47 95 86 ef cd ab 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 44 00 00 fe fd 73 00 a0 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00
80:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a3) Subsystem: Tyan Computer Unknown device [10f1:2915] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 255 Region 0: I/O ports at 5000 [size=64] Region 4: I/O ports at 5440 [size=64] Region 5: I/O ports at 5400 [size=64] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel driver in use: nForce2_smbus 00: de 10 68 03 01 00 b0 00 a3 00 05 0c 00 00 80 00 10: 01 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 41 54 00 00 01 54 00 00 00 00 00 00 f1 10 15 29 30: 00 00 00 00 44 00 00 00 00 00 00 00 ff 01 00 00 40: f1 10 15 29 01 00 02 c0 00 00 00 00 00 00 00 00 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 60: 01 f0 00 00 01 f4 00 00 01 f8 00 00 00 00 00 00 70: 01 00 00 00 00 00 04 c0 00 00 00 00 01 00 00 00 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: d4 30 80 00 01 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: e6 16 05 00 a5 21 50 03 80 ff f7 00 61 44 44 11 f0: 5a ff 5f 3f 00 00 00 c0 10 00 00 00 00 00 00 00
80:0a.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0376] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=80, secondary=81, subordinate=81, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4169 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #5, Speed 2.5GT/s, Width x8, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 76 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 80 81 81 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 69 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 81 3c 11 05 90: 00 00 81 10 00 00 00 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80:0d.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0378] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=80, secondary=82, subordinate=82, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4171 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #2, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 78 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 80 82 82 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 71 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 41 3c 11 02 90: 00 00 41 10 00 00 00 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge [10de:0377] (rev a3) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=80, secondary=83, subordinate=83, sec-latency=0 Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: [40] Subsystem: nVidia Corporation Unknown device [10de:0000] Capabilities: [48] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+ Address: 00000000fee0f00c Data: 4179 Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed- Mapping Address Base: 00000000fee00000 Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us ExtTag- RBE+ FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us ClockPM- Suprise- LLActRep+ BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk- ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise- Slot # 0, PowerLimit 0.000000; Interlock- NoCompl- SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg- Control: AttnInd Off, PwrInd On, Power- Interlock- SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock- Changed: MRL- PresDet- LinkState- RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible- RootCap: CRSVisible- RootSta: PME ReqID 0000, PMEStatus- PMEPending- Capabilities: [100] Virtual Channel <?> Capabilities: [160] Advanced Error Reporting <?> Kernel driver in use: pcieport-driver 00: de 10 77 03 47 05 10 00 a3 00 04 06 10 00 01 00 10: 00 00 00 00 00 00 00 00 80 83 83 00 f1 01 00 00 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 ff 00 04 00 40: 0d 48 00 00 de 10 00 00 01 50 02 f8 00 00 00 00 50: 05 60 83 00 0c f0 e0 fe 00 00 00 00 79 41 00 00 60: 08 80 00 a8 00 00 e0 fe 00 00 00 00 00 00 00 00 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80: 10 00 41 01 01 80 00 00 1f 28 00 00 01 3d 11 00 90: 00 00 01 11 00 00 00 00 c0 01 00 00 00 00 00 00 a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* superiotool -deV superiotool r Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0x0000, rev=0x00 Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x0400, id=0x0081 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0x8100, rev=0x1 Probing for ITE Super I/O (init=it8502e) at 0x2e... Failed. Returned data: id=0x8100, rev=0x1 Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0x8100, rev=0x1 Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0x8100, rev=0x1 Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x8100, rev=0x1 Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8502e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for Nuvoton Super I/O (sid=0xfc) at 0x164e... Failed. Returned data: sid=0xff, id=0x00, rev=0x00 Probing for Nuvoton Super I/O (sid=0xfc) at 0x2e... Failed. Returned data: sid=0xff, id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Found SMSC SCH5307 (id=0x81, rev=0x00) at 0x2e No dump available for this Super I/O No extra registers known for this chip. Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0x00, rev=0x00 Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0x00/0x00, rev=0x00 Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for VIA Super I/O at 0x3f0... PCI device 1106:0686 not found.
Am Montag, den 26.07.2010, 14:23 +0200 schrieb Axel Bergerhoff:
Hi,
tried several Tyan 2915 (S2915A2NRF) and S2915-E (S2915A2NRF-E) all with the same result. #1 Using flashrom -r to get the PROM's content and comparing that with the appropriate version from Tyan's website gives differences in all cases.
This is common, because parts of the PROM are nowadays used for data storage like event log (when was the system booted?), for DMI data (like the system's serial number) or even sometimes for special configuration options. This is not a problem, but working as expected.
You can verify this claim by trying to make a backup of your current BIOS contents with phlash16 - you will find out that this also won't match the vendor image.
Regards, Michael Karcher
Hi, Axel Bergerhoff schrieb:
tried several Tyan 2915 (S2915A2NRF) and S2915-E (S2915A2NRF-E) all with the same result. #1 Using flashrom -r to get the PROM's content and comparing that with the appropriate version from Tyan's website gives differences in all cases.
That's expected behaviour. Your flash will contain serial numbers of you board, MAC address(es) of your on-board NIC(s) and other dynamic stuff. The flash tool form your vendor will know about this and does not touch these specific areas.
Flashrom on the other hand does not know anything about this and will happily overwrite this data.
#2 Took a 2915 (S2915A2NRF) and flashed with the DOS tool offered by Tyan (phlash16.exe) to BIOS revision 3.00 (2915v300.rom). Then reread with flashrom -r and compared both files - a bunch of differencies again. I attached the outputs of flashrom, lspci, and superiotool for this board.
Same issue here.
-- Jim
Am Montag, 26. Juli 2010 schrieb Jörg Fischer:
Hi,
Axel Bergerhoff schrieb:
tried several Tyan 2915 (S2915A2NRF) and S2915-E (S2915A2NRF-E) all with the same result. #1 Using flashrom -r to get the PROM's content and comparing that with the appropriate version from Tyan's website gives differences in all cases.
That's expected behaviour. Your flash will contain serial numbers of you board, MAC address(es) of your on-board NIC(s) and other dynamic stuff. The flash tool form your vendor will know about this and does not touch these specific areas.
Flashrom on the other hand does not know anything about this and will happily overwrite this data.
#2 Took a 2915 (S2915A2NRF) and flashed with the DOS tool offered by Tyan (phlash16.exe) to BIOS revision 3.00 (2915v300.rom). Then reread with flashrom -r and compared both files - a bunch of differencies again. I attached the outputs of flashrom, lspci, and superiotool for this board.
Same issue here.
-- Jim
Thx. Just flashed the first one with flashrom, worked fine.
Axel
On Tue, Jul 27, 2010 at 11:06:10AM +0200, Axel Bergerhoff wrote:
Just flashed the first one with flashrom, worked fine.
Thanks, we marked the S2915 as supported. If you get a chance to also test S2915-E please let us know.
Uwe.
Am Donnerstag, 29. Juli 2010 schrieb Uwe Hermann:
On Tue, Jul 27, 2010 at 11:06:10AM +0200, Axel Bergerhoff wrote:
Just flashed the first one with flashrom, worked fine.
Thanks, we marked the S2915 as supported. If you get a chance to also test S2915-E please let us know.
Uwe.
All of our 2915-E boards that are still running older BIOS versions are attached to server boxes. As the BIOS settings are reset to defaults while flashing (no matter if flashrom or phlash16 is used) and the defaults prevent the OS from booting up, an immediate reboot and readjust is mandatory.
I'll be out of town for a couple of weeks now - I'll test when I'm back.
Axel
Am Donnerstag, 29. Juli 2010 schrieb Uwe Hermann:
On Tue, Jul 27, 2010 at 11:06:10AM +0200, Axel Bergerhoff wrote:
Just flashed the first one with flashrom, worked fine.
Thanks, we marked the S2915 as supported. If you get a chance to also test S2915-E please let us know.
Uwe.
All of our 2915-E boards that are still running older BIOS versions are attached to server boxes. As the BIOS settings are reset to defaults while flashing (no matter if flashrom or phlash16 is used) and the defaults prevent the OS from booting up, an immediate reboot and readjust is mandatory.
I'll be out of town for a couple of weeks now - I'll test when I'm back.
Axel
Back again. Successfully flashed one 2915-E some minutes ago.
<Description> * Environment ** board: Tyan Thunder n6650W (S2915A2NRF-E) ** flashrom: flashrom-0.9.2-r1096 ** new BIOS: 2915v401.ROM (from S2915-E_v401.zip)
* Procedure ** Reduce file size of 2915v401.ROM As somebody already mentioned some time ago ROMs for 2915 and 2915-E are bigger than 1 MB - but the rest is not needed. To avoid error messages from flashrom, the ROM file should be cut off. There are many ways to do, I used split: split -b 1m 2915v401.ROM This gives two files, xaa and xab, where xaa is the choosen one. ** Save the active ROM content to a file, e.g. ROM.sav flashrom -r ROM.sav ** Flash flashrom -w xaa Should return with "Verified" ** Reboot ** Readjust the BIOS settings! Many board manufacturers claim BIOS setup to be reset to some default but actually leave everything untouched. Here resetting _is_ done (no matter if flashrom or the DOS based tool from Tyan is used), disabling your RAID controller as a boot device, disabling IOMMU, setting system time some years to the past, .. </Description>
Thanks for doing a good job! Axel
On Mon, Aug 30, 2010 at 08:27:23AM +0200, Axel Bergerhoff wrote:
Back again. Successfully flashed one 2915-E some minutes ago.
<Description> * Environment ** board: Tyan Thunder n6650W (S2915A2NRF-E) ** flashrom: flashrom-0.9.2-r1096 ** new BIOS: 2915v401.ROM (from S2915-E_v401.zip)
Great, thanks! Marked as supported now.
Uwe.
-
Axel Bergerhoff -
Jörg Fischer -
Michael Karcher -
Uwe Hermann