I've not actually flashed the BIOS yet, as I'm apprehensive. Having said this here are the results of commands for your projects reference which have also been pastebinned http://flashrom.pastebin.com/Ts5FxCHB
/home/naesk$ sudo flashrom
flashrom v0.9.1-r946 No coreboot table found. Found chipset "Intel ICH5/ICH5R", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... OK. Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. No operations were specified.
/home/naesk$ sudo flashrom -r backup.bin
flashrom v0.9.1-r946 No coreboot table found. Found chipset "Intel ICH5/ICH5R", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... OK. Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Reading flash... done.
/home/naesk$ sudo flashrom -V
flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "System manufacturer" DMI string system-product-name: "System Product Name" DMI string system-version: "System Version" DMI string baseboard-manufacturer: "ASUSTeK Computer Inc." DMI string baseboard-product-name: "P5P800-SE" DMI string baseboard-version: "Rev 1.xx" DMI string chassis-type: "Desktop" Found chipset "Intel ICH5/ICH5R", enabling flash write... BIOS Lock Enable: disabled, BIOS Write Enable: enabled, BIOS_CNTL is 0x1 OK. This chipset supports the following protocols: Non-SPI. Calibrating delay loop... 853M loops per second, 100 myus = 200 us. OK. Probing for AMD Am29F010A/B, 128 KB: probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT25DF021, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF041A, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF081, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF321A, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25DF641, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25F512B, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT25FS040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF041, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF081A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26DF161A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT26F004, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT29C512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT29C010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT29C020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT29C040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT45CS1282, 16896 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB011D, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB021D, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB041D, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB081D, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB161D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321C, 4224 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB321D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT45DB642D, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Atmel AT49BV512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49F002(N), 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49F002(N)T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for AMIC A25L40PT, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A25L40PU, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for AMIC A29002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for EMST F49B002UA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Eon EN25B05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B05T, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B10T, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B20T, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B40T, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B80T, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B16T, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B32T, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25B64T, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25D16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F05, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN25F32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Eon EN29F010, 128 KB: probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)B, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for EON EN29F002(A)(N)T, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004BC, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Fujitsu MBM29F400TC, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for Intel 28F001BX-B, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Intel 28F001BX-T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Intel 28F004S5, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Macronix MX25L512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1005, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L2005, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L4005, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L8005, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1605, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L1635D, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3205, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L3235D, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L6405, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX25L12805, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix MX29F001B, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Numonyx M25PE10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Numonyx M25PE16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV010, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV020, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV040, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm25LV512, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC Pm29F002T, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 KB: probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Sanyo LF25FW203A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for Spansion S25FL008A, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Spansion S25FL016A, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF016B, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF032B, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF040B.REMS, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST25VF080B, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST SST28SF040A, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST29EE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST29LE010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST29EE020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST29LE020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39SF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39SF010A, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39SF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39SF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF512, 64 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF010, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF080, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Found chip "SST SST49LF004A/B" (512 KB, FWH) at physical address 0xfff80000. Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M25P05-A, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P05.RES, 64 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10-A, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P10.RES, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P40-old, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M25P128, 16384 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST M29F002B, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BT, 512 KB: probe_m29f400bt: id1 0xff, id2 0xff Probing for ST M29W010B, 128 KB: probe_jedec_common: id1 0x69, id2 0xe9, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 KB: probe_jedec_common: id1 0xfc, id2 0xa3, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x3f, id2 0x46 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff Probing for SyncMOS S29C31004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51001T, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51002T, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS S29C51004T, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for TI TMS29F002RB, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 KB: probe_jedec_common: id1 0x3f, id2 0x46, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W25x10, 128 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x20, 256 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x40, 512 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x80, 1024 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x16, 2048 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x32, 4096 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W25x64, 8192 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Winbond W29C011, 128 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W29C020C, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W29C040P, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W29EE011, 128 KB: Probing disabled for Winbond W29EE011 because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29EE011' if you have a board with this chip. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel unknown Atmel SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for EON unknown EON SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Macronix unknown Macronix SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for PMC unknown PMC SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for SST unknown SST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for ST unknown ST SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Sanyo unknown Sanyo SPI chip, 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (RDID), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. Probing for Generic unknown SPI chip (REMS), 0 KB: skipped. Host bus type Non-SPI and chip bus type SPI are incompatible. No operations were specified.
/home/naesk$ lspci -nnvvxxx 00:00.0 Host bridge [0600]: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface [8086:2570] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80f2] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] Capabilities: <access denied> Kernel driver in use: agpgart-intel Kernel modules: intel-agp 00: 86 80 70 25 06 01 90 20 02 00 00 06 00 00 00 00 10: 08 00 00 d0 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 f2 80 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
00:01.0 PCI bridge [0604]: Intel Corporation 82865G/PE/P PCI to AGP Controller [8086:2571] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: f9000000-fbefffff Prefetchable memory behind bridge: e0000000-f7ffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 71 25 07 01 a0 00 02 00 04 06 00 40 01 00 10: 00 00 00 00 00 00 00 00 00 01 01 40 d0 d0 a0 22 20: 00 f9 e0 fb 00 e0 f0 f7 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08 00
00:06.0 System peripheral [0880]: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface [8086:2576] (rev 02) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at fecf0000 (32-bit, non-prefetchable) [size=4K] 00: 86 80 76 25 02 00 80 00 02 00 80 08 00 00 00 00 10: 00 00 cf fe 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:1d.0 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 [8086:24d2] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at b800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d2 24 05 00 80 02 02 00 03 0c 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 b8 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
00:1d.1 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 [8086:24d4] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 19 Region 4: I/O ports at c000 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d4 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 c0 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
00:1d.2 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 [8086:24d7] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at c400 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 d7 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 c4 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 03 00 00
00:1d.3 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #4 [8086:24de] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at c800 [size=32] Kernel driver in use: uhci_hcd 00: 86 80 de 24 05 00 80 02 02 00 03 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 c8 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 0a 01 00 00
00:1d.7 USB Controller [0c03]: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller [8086:24dd] (rev 02) (prog-if 20) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 23 Region 0: Memory at f8fffc00 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00: 86 80 dd 24 06 01 90 02 02 20 03 0c 00 00 00 00 10: 00 fc ff f8 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 04 00 00
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c2) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fbf00000-fbffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Kernel modules: shpchp 00: 86 80 4e 24 07 01 80 00 c2 00 04 06 00 00 01 00 10: 00 00 00 00 00 00 00 00 00 02 02 40 e0 e0 80 22 20: f0 fb f0 fb f0 ff 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
00:1f.0 ISA bridge [0601]: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge [8086:24d0] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00: 86 80 d0 24 0f 00 80 02 02 00 01 06 00 00 80 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:1f.1 IDE interface [0101]: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller [8086:24db] (rev 02) (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at fc00 [size=16] Region 5: Memory at c0000000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: ata_piix 00: 86 80 db 24 07 00 80 02 02 8a 01 01 00 00 00 00 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00 20: 01 fc 00 00 00 00 00 c0 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:1f.2 IDE interface [0101]: Intel Corporation 82801EB (ICH5) SATA Controller [8086:24d1] (rev 02) (prog-if 8f [Master SecP SecO PriP PriO]) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 18 Region 0: I/O ports at a800 [size=8] Region 1: I/O ports at a400 [size=4] Region 2: I/O ports at a000 [size=8] Region 3: I/O ports at 9800 [size=4] Region 4: I/O ports at 9400 [size=16] Kernel driver in use: ata_piix 00: 86 80 d1 24 05 00 a0 02 02 8f 01 01 00 00 00 00 10: 01 a8 00 00 01 a4 00 00 01 a0 00 00 01 98 00 00 20: 01 94 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 01 00 00
00:1f.3 SMBus [0c05]: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller [8086:24d3] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80a6] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 6 Region 4: I/O ports at 0400 [size=32] Kernel modules: i2c-i801 00: 86 80 d3 24 01 00 80 02 02 00 05 0c 00 00 00 00 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 01 04 00 00 00 00 00 00 00 00 00 00 43 10 a6 80 30: 00 00 00 00 00 00 00 00 00 00 00 00 06 02 00 00
00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller [8086:24d5] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:810d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: I/O ports at b400 [size=256] Region 1: I/O ports at b000 [size=64] Region 2: Memory at f8fff800 (32-bit, non-prefetchable) [size=512] Region 3: Memory at f8fff400 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: Intel ICH Kernel modules: snd-intel8x0 00: 86 80 d5 24 07 00 90 02 02 00 01 04 00 00 00 00 10: 01 b4 00 00 01 b0 00 00 00 f8 ff f8 00 f4 ff f8 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 0d 81 30: 00 00 00 00 50 00 00 00 00 00 00 00 06 02 00 00
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV44A [GeForce 6200] [10de:0221] (rev a1) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 248 (1250ns min, 250ns max) Interrupt: pin A routed to IRQ 16 Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M] Region 1: Memory at e0000000 (32-bit, prefetchable) [size=256M] Region 2: Memory at f9000000 (32-bit, non-prefetchable) [size=16M] [virtual] Expansion ROM at fbee0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: nvidia Kernel modules: nvidia-current, nvidia-173, nvidiafb, nouveau 00: de 10 21 02 07 01 b0 02 a1 00 00 03 00 f8 00 00 10: 00 00 00 fa 08 00 00 e0 00 00 00 f9 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 30: 00 00 00 00 60 00 00 00 00 00 00 00 0a 01 05 01
02:05.0 Ethernet controller [0200]: Intel Corporation 82540EM Gigabit Ethernet Controller [8086:100e] (rev 02) Subsystem: ASUSTeK Computer Inc. Device [1043:80ee] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 16 bytes Interrupt: pin A routed to IRQ 22 Region 0: Memory at fbfe0000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at e800 [size=64] Capabilities: <access denied> Kernel driver in use: e1000 Kernel modules: e1000 00: 86 80 0e 10 17 01 30 02 02 00 00 02 04 40 00 00 10: 00 00 fe fb 00 00 00 00 01 e8 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 43 10 ee 80 30: 00 00 00 00 dc 00 00 00 00 00 00 00 0b 01 ff 00
02:0b.0 Multimedia controller [0480]: Philips Semiconductors SAA7131/SAA7133/SAA7135 Video Broadcast Decoder [1131:7133] (rev d0) Subsystem: Pinnacle Systems Inc. Device [11bd:002f] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (21000ns min, 8000ns max) Interrupt: pin A routed to IRQ 23 Region 0: Memory at fbfdb800 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: saa7134 Kernel modules: saa7134 00: 31 11 33 71 06 01 90 02 d0 00 80 04 00 40 00 00 10: 00 b8 fd fb 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 bd 11 2f 00 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 54 20
02:0c.0 Network controller [0280]: RaLink RT2561/RT61 802.11g PCI [1814:0301] Subsystem: RaLink Device [1814:2561] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 128 bytes Interrupt: pin A routed to IRQ 20 Region 0: Memory at fbfd0000 (32-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: rt61pci Kernel modules: rt61pci 00: 14 18 01 03 17 01 10 04 00 00 80 02 20 40 00 00 10: 00 00 fd fb 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 01 06 00 00 14 18 61 25 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 01 00 00
/home/naesk$ sudo superiotool -deV
superiotool r3844 Probing for ALi Super I/O at 0x3f0... Failed. Returned data: id=0xffff, rev=0xff Probing for ALi Super I/O at 0x370... Failed. Returned data: id=0xffff, rev=0xff Probing for Fintek Super I/O at 0x2e... Failed. Returned data: vid=0x4400, id=0x6388 Probing for Fintek Super I/O at 0x4e... Failed. Returned data: vid=0xffff, id=0xffff Probing for ITE Super I/O (init=standard) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x2e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... Failed. Returned data: id=0x8863, rev=0xf Probing for ITE Super I/O (init=standard) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8761e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=it8228e) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8661f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for ITE Super I/O (init=legacy/it8671f) at 0x370... Failed. Returned data: id=0xffff, rev=0xf Probing for NSC Super I/O at 0x2e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x4e... Failed. Returned data: port=0xff, port+1=0xff Probing for NSC Super I/O at 0x15c... Failed. Returned data: port=0xff, port+1=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... Failed. Returned data: id=0xff, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... Found Winbond W83627EHF/EF/EHG/EG (id=0x88, rev=0x63) at 0x2e Register dump: idx 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f val 88 63 ff 00 44 00 00 ff 50 04 00 00 98 21 00 ff def 88 MM ff 00 MM 00 MM RR 50 04 00 RR 00 21 00 00 LDN 0x00 (Floppy) idx 30 60 61 70 74 f0 f1 f2 f4 f5 val 00 03 f0 06 02 0e 00 ff 00 00 def 01 03 f0 06 02 8e 00 ff 00 00 LDN 0x01 (Parallel port) idx 30 60 61 70 74 f0 val 01 03 78 07 03 3a def 01 03 78 07 04 3f LDN 0x02 (COM1) idx 30 60 61 70 f0 val 01 03 f8 04 00 def 01 03 f8 04 00 LDN 0x03 (COM2) idx 30 60 61 70 f0 f1 val 00 02 f8 03 00 00 def 01 02 f8 03 00 00 LDN 0x05 (Keyboard) idx 30 60 61 62 63 70 72 f0 val 01 00 60 00 64 01 0c 83 def 01 00 60 00 64 01 0c 83 LDN 0x06 (Serial flash interface) idx 30 62 63 val 00 ff ff def 00 00 00 LDN 0x07 (GPIO 1, GPIO 6, game port, MIDI port) idx 30 60 61 62 63 70 f0 f1 f2 f3 f4 f5 f6 f7 val 00 02 01 03 30 00 ff ff ff ff ff ff ff 00 def 00 02 01 03 30 09 ff 00 00 00 ff 00 00 00 LDN 0x08 (WDTO#, PLED) idx 30 f5 f6 f7 val 00 ff 00 ff def 00 00 00 00 LDN 0x09 (GPIO 2, GPIO 3, GPIO 4, GPIO 5, SUSLED) idx 30 e0 e1 e2 e3 e4 e5 f0 f1 f2 f3 f4 f5 f6 f7 val 0b fe 20 00 f7 08 00 f3 0c 00 09 ff ff ff ff def 00 ff 00 00 ff 00 00 ff 00 00 00 ff 00 00 00 LDN 0x0a (ACPI) idx 30 70 e0 e1 e2 e3 e4 e5 e6 e7 e8 f2 f3 f4 f6 f7 val 01 00 00 00 ff 24 00 02 0c 10 09 7d 00 00 00 00 def 00 00 01 00 ff 08 00 RR 00 00 RR 7c 00 00 00 00 LDN 0x0b (Hardware monitor) idx 30 60 61 70 f0 f1 val 01 02 90 00 c1 16 def 00 00 00 00 c1 00 Hardware monitor (0x0295) Probing for Winbond Super I/O (init=0x88) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x88) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x89) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff
-
Sean Kelly