Hi,
I'm running Ubuntu 12.04 and I was testing flashrom on my new workstation, a Dell Precision T5600 but it's not working. Here the log:
$ sudo flashrom -V flashrom v0.9.5.2-r1517 on Linux 3.2.0-38-generic (x86_64), built with libpci 3.1.8, GCC 4.6.3, little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 3770M loops per second, 10 myus = 11 us, 100 myus = 105 us, 1000 myus = 1045 us, 10000 myus = 10111 us, 4 myus = 14 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "Dell Inc." DMI string system-product-name: "Precision T5600" DMI string system-version: "01" DMI string baseboard-manufacturer: "Dell Inc." DMI string baseboard-product-name: "0Y56T3" DMI string baseboard-version: "A01" DMI string chassis-type: "Tower" Found chipset "Intel X79" with PCI ID 8086:1d41. This chipset is marked as untested. If you are using an up-to-date version of flashrom please email a report to flashrom@flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0xa WARNING: Setting 0xdc from 0xa to 0xb on X79 failed. New value is 0xa. Root Complex Register Block address = 0xfed1c000 GCS = 0xc61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done 0x06: 0x3f00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x00001a1b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x0bff0600 FREG1: BIOS region (0x00600000-0x00bfffff) is read-write. 0x5C: 0x05ff0006 FREG2: WARNING: Management Engine region (0x00006000-0x005fffff) is locked. 0x60: 0x00050002 FREG3: Gigabit Ethernet region (0x00002000-0x00005fff) is read-write. 0x64: 0x00010001 FREG4: Platform Data region (0x00001000-0x00001fff) is read-write. Please send a verbose log to flashrom@flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x84 (SSFS) SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0 0x91: 0xf84030 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=3, DBC=0, SME=0, SCF=0 0x94: 0x0606 (PREOP) 0x96: 0x743b (OPTYPE) 0x98: 0x05200302 (OPMENU) 0x9C: 0x0420019f (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00802005 (LVSCC) LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1 0xC8: 0x00002005 (UVSCC) UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0 0xD0: 0x00000800 (FPB)
Enabling hardware sequencing due to multiple flash chips detected. SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 2 attached SPI flash chips with a combined density of 12288 kB. The flash address space (0x000000 - 0x3fffff) is divided at address 0x800000 in two partitions. The first partition ranges from 0x000000 to 0x7fffff. In that range are 2048 erase blocks with 4096 B each. The second partition ranges from 0x800000 to 0x3fffff. In that range are 1024 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific) at physical address 0x0. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xc9, id2 0x05, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xc9, id2 0x05, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xc9, id2 0x05, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x00, id2 0x68, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xc9, id2 0x05, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xc9, id2 0x05, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x9e, id2 0x4a, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (12288 kB, Programmer-specific). No operations were specified. Restoring MMIO space at 0x7fb8c9c668a0 Restoring PCI config space for 00:1f:0 reg 0xdc
-
Clement Fevrier