I have some additional information from Erickson. I appreciate any help you can provide. Intel(R) Xeon(R) CPU E5-2448L v2 @ 1.80GHz E5-2600 v1 Sandybridge and v2 Ivybridage platforms also have seen slow flash issue in Numonyx part.
Chipset Code name CaveCreek DH8900, ICH9 compatible.
------------------------- Send OPCODE 0xC7 to flash chip ask for bulk erase, sometimes it work, sometimes it stuck no response back. Same experiment for Spansion flash works fine. -----------------------
Open source tool flashrom clear SRWD and BP0, BP1, BP2 and BP3 bits of Status Register prior to erase and write for sure.
Flashrom for "Micron/Numonyx/ST" go 4KB subsector erase in default. Enforce OPCOED 0xD8 performing 64KB erase
“bulk erase” is unstable, and SPI bus stuck in SCIP SPI Cycle in progress. If you have time, we can co-work debugging it about bulk erase bus cycle jam issue.
Found Micron/Numonyx/ST flash chip "N25Q128..3E" (16384 kB, SPI) mapped at physical address 0x00000000ff000000. Reading old flash chip contents... done. Erasing and writing flash chip... timeout, ICH9_REG_SSFS=0xf8007401 spi_chip_erase_c7 failed during command execution Reading current flash chip contents... Error: SCIP never cleared! Can't read anymore! Aborting. FAILED! Uh oh. Erase/write failed. Checking if anything has changed. Reading current flash chip contents... Error: SCIP never cleared! Can't even read anymore! Your flash chip is in an unknown state. Get help on IRC at chat.freenode.net (channel #flashrom) or mail flashrom@flashrom.org with the subject "FAILED: <your board name>"!
Sent from Surface
From: Scott Emmartmailto:semmart@micron.com Sent: Monday, June 8, 2015 4:09 PM To: flashrom@flashrom.orgmailto:flashrom@flashrom.org
Hi I have 2 customers experiencing issues with Bulk erase with our Micron/Numonyx/ST
N25Q128..3E
16384
SPI
OK
OK
OK
OK
2.700
3.600
What can I do to help get this situation looked at? I am working on getting board names is there any other information you need??
From IBM: Found Micron/Numonyx/ST flash chip "N25Q128..3E" (16384 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Write/erase is not working yet on your programmer in its current configuration. Continuing anyway. Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... Transaction error! SSFS: SCIP=0, FDONE=1, FCERR=1, AEL=0 SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=63, SME=0, SCF=0 Running OPCODE 0x03 failed at address 0x001000 (payload length was 64). FAILED.
From Ericson……… N25Q128A13ESF40F ------------------------- Send OPCODE 0xC7 to flash chip ask for bulk erase, sometimes it work, sometimes it stuck no response back. Same experiment for Spansion flash works fine. -----------------------
Open source tool flashrom clear SRWD and BP0, BP1, BP2 and BP3 bits of Status Register prior to erase and write for sure.
Flashrom for "Micron/Numonyx/ST" go 4KB subsector erase in default. Enforce OPCOED 0xD8 performing 64KB erase
“bulk erase” is unstable, and SPI bus stuck in SCIP SPI Cycle in progress. If you have time, we can co-work debugging it about bulk erase bus cycle jam issue.
Found Micron/Numonyx/ST flash chip "N25Q128..3E" (16384 kB, SPI) mapped at physical address 0x00000000ff000000. Reading old flash chip contents... done. Erasing and writing flash chip... timeout, ICH9_REG_SSFS=0xf8007401 spi_chip_erase_c7 failed during command execution Reading current flash chip contents... Error: SCIP never cleared! Can't read anymore! Aborting. FAILED! Uh oh. Erase/write failed. Checking if anything has changed. Reading current flash chip contents... Error: SCIP never cleared! Can't even read anymore! Your flash chip is in an unknown state. Get help on IRC at chat.freenode.net (channel #flashrom) or mail flashrom@flashrom.org with the subject "FAILED: <your board name>"!
Thank you,
Scott Emmart
Micron Technology, Inc.
Senior Manager | World Wide Customer Engineering Labshttp://www.micron.com/solutions/global-customer-labs T: 208 368-3022 I M: 208 585-7337 I semmart@micron.commailto:semmart@micron.com [logo-micron]http://www.micron.com/ [micron_tag_line]
-
David Hendricks -
Scott Emmart (semmart)