Hello Stefan,
here's output: flashrom v0.9.5.2-r1515 on Linux 2.6.33.7-desktop-2mnb (i686), built with libpci 3.1.7, GCC 4.6.1 20110627 (Mandriva), little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 1855M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1004 us, 10000 myus = 10008 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: " " DMI string system-product-name: " " DMI string system-version: " " DMI string baseboard-manufacturer: "Intel Corporation" DMI string baseboard-product-name: "DQ965GF" DMI string baseboard-version: "AAD41676-400" DMI string chassis-type: "Desktop" Found chipset "Intel ICH8DO" with PCI ID 8086:2814. Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode disabled 0xffe00000/0xffa00000 FWH decode disabled 0xffd80000/0xff980000 FWH decode disabled 0xffd00000/0xff900000 FWH decode disabled 0xffc80000/0xff880000 FWH decode disabled 0xffc00000/0xff800000 FWH decode disabled 0xff700000/0xff300000 FWH decode disabled 0xff600000/0xff200000 FWH decode disabled 0xff500000/0xff100000 FWH decode disabled 0xff400000/0xff000000 FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0xa WARNING: Setting 0xdc from 0xa to 0xb on ICH8DO failed. New value is 0xa. Root Complex Register Block address = 0xfed1c000 GCS = 0x464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3020 0x04: 0xe008 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 WARNING: SPI Configuration Lockdown activated. Reading OPCODES... done OP Type Pre-OP op[0]: 0x9f, read w/o addr, none op[1]: 0xab, read w/ addr, none op[2]: 0x00, read w/o addr, none op[3]: 0x00, read w/o addr, none op[4]: 0x00, read w/o addr, none op[5]: 0x00, read w/o addr, none op[6]: 0x00, read w/o addr, none op[7]: 0x00, read w/o addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x00 0x06: 0x3b00 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=59, SME=0 0x08: 0x00122201 (FADDR) 0x50: 0x00000a0b (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b 0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only. 0x58: 0x01ff0120 FREG1: BIOS region (0x00120000-0x001fffff) is read-write. 0x5C: 0x011f0003 FREG2: WARNING: Management Engine region (0x00003000-0x0011ffff) is locked. 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write. 0x64: 0x00000000 FREG4: WARNING: Platform Data region (0x00000000-0x00000fff) is locked. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) Please send a verbose log to flashrom@flashrom.org if this board is not listed on http://flashrom.org/Supported_hardware#Supported_mainboards yet. Writes have been disabled. You can enforce write support with the ich_spi_force programmer option, but it will most likely harm your hardware! If you force flashrom you will get no support if something breaks. 0x90: 0x00 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0x004200 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=2, SME=0, SCF=0 0x94: 0x0006 (PREOP) 0x96: 0x0008 (OPTYPE) 0x98: 0x0000ab9f (OPMENU) 0x9C: 0x00000000 (OPMENU+4) 0xC1: 0xffffffff (VSCC) VSCC: BES=0x3, WG=1, WSR=1, WEWS=1, EO=0xff, VCL=1
Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x03040001 FLMAP1 0x01100206 FLMAP2 0x00000120
--- Details --- NR (Number of Regions): 4 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x010 ISL (ICH/PCH Strap Length): 1 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200
=== Component Section === FLCOMP 0x00300002 FLILL 0x00000000
--- Details --- Component 1 density: 2 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 20 MHz Write and Erase Clock Freq.: 20 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes.
=== Region Section === FLREG0 0x00000000 FLREG1 0x01ff0120 FLREG2 0x011f0003 FLREG3 0x00020001 FLREG4 0x00000000
--- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00120000 - 0x001fffff Region 2 (ME ) 0x00003000 - 0x0011ffff Region 3 (GbE ) 0x00001000 - 0x00002fff Region 4 (Platf.) 0x00000000 - 0x00000fff
=== Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08090218
--- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE r rw
Enabling hardware sequencing because some important opcode is locked. SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway The following protocols are supported: FWH, Programmer-specific. Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip with a density of 2048 kB. There is only one partition containing the whole address space (0x000000 - 0x1fffff). There are 512 erase blocks with 4096 B each. Found Programmer flash chip "Opaque flash chip" (2048 kB, Programmer-specific) at physical address 0x0. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x4b, id2 0x93, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x4b, id2 0x93, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x4b, id2 0x93, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x0c, id2 0xe1, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x4b, id2 0x93, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x4b, id2 0x93, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x5a, id2 0x47, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Programmer flash chip "Opaque flash chip" (2048 kB, Programmer-specific). Reading flash... Reading 2097152 bytes starting at 0x000000. Transaction error between offset 0x00003000 and 0x0000303f (= 0x00003000 + 63)! HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1 HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0 Read operation failed! FAILED. Restoring PCI config space for 00:1f:0 reg 0xdc
On Fri, May 18, 2012 at 2:17 AM, Stefan Tauner < stefan.tauner@student.tuwien.ac.at> wrote:
On Tue, 15 May 2012 03:19:53 +0300 gabris gabris.t@gmail.com wrote:
Hello, as written in flashrom I'm sending verbose log which is from Intel DQ965GF motherboard running Q965, Mandriva 2010.2 as OS. it has
SST25VF016B
Bioschip.
Hello gabris,
thanks for your report!
I have added the board to our list of (un)supported boards (with an appropriate note) and will commit that later together with other small changes.
It wont change anything regarding support of the board, but i would like to see the output of flashrom -VV -r image.tmp It will try to read the whole flash chip and will fail and i want to know where. This test is safe.
-- Kind regards/Mit freundlichen Grüßen, Stefan Tauner