2010/7/21 Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Speed up RayeR SPIPGM driver in flashrom by a factor of 2.

Allow specification of an alternate base port with
flashrom -p rayer_spi:lptport=0x278
Any port number is allowed as long as it is nonzero, below 65536 and a
multiple of four.

Untested, should work.

Martin, this one should hopefully reach the speed of SPIPGM.exe for
reads. I'll ask Idwer to provide a DOS binary for you.

http://khepri.coresystems.de/~idwer/flashrom/r1093-patchwork-1666/
 

Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>

Index: flashrom-bitbang_spi_rayer_faster/flashrom.8
===================================================================
--- flashrom-bitbang_spi_rayer_faster/flashrom.8        (Revision 1093)
+++ flashrom-bitbang_spi_rayer_faster/flashrom.8        (Arbeitskopie)
@@ -394,7 +394,18 @@
 (in Hz). The default is the maximum frequency of 8 MHz.
 .TP
 .BR "rayer_spi " programmer
-No parameters defined yet. More information about the hardware is available at
+The default I/O base address used for the parallel port is 0x378 and you can use
+the optional
+.B lptport
+parameter to specify an alternate base I/O address with the
+.sp
+.B "  flashrom \-p rayer_spi:lptport=portnum"
+.sp
+syntax where
+.B portnum
+is the I/O port number of your parallel port which must be a multiple of 4.
+.sp
+More information about the hardware is available at
 http://rayer.ic.cz/elektro/spipgm.htm
 .SH EXIT STATUS
 flashrom exits with 0 on success, 1 on most failures but with 2 if /dev/mem
Index: flashrom-bitbang_spi_rayer_faster/rayer_spi.c
===================================================================
--- flashrom-bitbang_spi_rayer_faster/rayer_spi.c       (Revision 1093)
+++ flashrom-bitbang_spi_rayer_faster/rayer_spi.c       (Arbeitskopie)
@@ -30,6 +30,7 @@
 */
 #if defined(__i386__) || defined(__x86_64__)

+#include <stdlib.h>
 #include "flash.h"

 /* We have two sets of pins, out and in. The numbers for both sets are
@@ -42,7 +43,7 @@
 /* Pins for slave->master direction */
 #define SPI_MISO_PIN 6

-static int lpt_iobase;
+static uint16_t lpt_iobase;

 /* FIXME: All rayer_bitbang_set_* functions could use caching of the value
 * stored at port lpt_iobase to avoid unnecessary INB. In theory, only one
@@ -50,37 +51,31 @@
 * value.
 */

-void rayer_bitbang_set_cs(int val)
+/* Cached value of last byte sent. */
+static uint8_t lpt_outval;
+
+static void rayer_bitbang_set_cs(int val)
 {
-       uint8_t tmp;
-
-       tmp = INB(lpt_iobase);
-       tmp &= ~(1 << SPI_CS_PIN);
-       tmp |= (val << SPI_CS_PIN);
-       OUTB(tmp, lpt_iobase);
+       lpt_outval &= ~(1 << SPI_CS_PIN);
+       lpt_outval |= (val << SPI_CS_PIN);
+       OUTB(lpt_outval, lpt_iobase);
 }

-void rayer_bitbang_set_sck(int val)
+static void rayer_bitbang_set_sck(int val)
 {
-       uint8_t tmp;
-
-       tmp = INB(lpt_iobase);
-       tmp &= ~(1 << SPI_SCK_PIN);
-       tmp |= (val << SPI_SCK_PIN);
-       OUTB(tmp, lpt_iobase);
+       lpt_outval &= ~(1 << SPI_SCK_PIN);
+       lpt_outval |= (val << SPI_SCK_PIN);
+       OUTB(lpt_outval, lpt_iobase);
 }

-void rayer_bitbang_set_mosi(int val)
+static void rayer_bitbang_set_mosi(int val)
 {
-       uint8_t tmp;
-
-       tmp = INB(lpt_iobase);
-       tmp &= ~(1 << SPI_MOSI_PIN);
-       tmp |= (val << SPI_MOSI_PIN);
-       OUTB(tmp, lpt_iobase);
+       lpt_outval &= ~(1 << SPI_MOSI_PIN);
+       lpt_outval |= (val << SPI_MOSI_PIN);
+       OUTB(lpt_outval, lpt_iobase);
 }

-int rayer_bitbang_get_miso(void)
+static int rayer_bitbang_get_miso(void)
 {
       uint8_t tmp;

@@ -99,16 +94,49 @@

 int rayer_spi_init(void)
 {
-       /* Pick a default value for now. */
-       lpt_iobase = 0x378;
+       char *portpos = NULL;

+       /* Non-default port requested? */
+       portpos = extract_programmer_param("lptport");
+       if (portpos) {
+               char *endptr = NULL;
+               unsigned long tmp;
+               tmp = strtoul(portpos, &endptr, 0);
+               /* Port 0, port >0x1000, unaligned ports and garbage strings
+                * are rejected.
+                */
+               if (!tmp || (tmp >= 0x10000) || (tmp & 0x3) ||
+                   (*endptr != '\0')) {
+                       /* Using ports below 0x100 is a really bad idea, and
+                        * should only be done if no port between 0x100 and
+                        * 0xfffc works due to routing issues.
+                        */
+                       msg_perr("Error: lptport specified, but no valid "
+                                "port specified.\nPort must be a multiple of "
+                                "0x4 and lie between 0x100 and 0xfffc.\n");
+                       free(portpos);
+                       return 1;
+               } else {
+                       lpt_iobase = (uint16_t)tmp;
+                       msg_pinfo("Non-default I/O base requested. This will "
+                                 "not change the hardware settings.\n");
+               }
+       } else {
+               /* Pick a default value for the I/O base. */
+               lpt_iobase = 0x378;
+       }
+       free(portpos);
+
       msg_pdbg("Using port 0x%x as I/O base for parallel port access.\n",
                lpt_iobase);

       get_io_perms();

-       /* 1 usec halfperiod delay for now. */
-       if (bitbang_spi_init(&bitbang_spi_master_rayer, 1))
+       /* Get the initial value before writing to any line. */
+       lpt_outval = INB(lpt_iobase);
+
+       /* Zero halfperiod delay. */
+       if (bitbang_spi_init(&bitbang_spi_master_rayer, 0))
               return 1;

       buses_supported = CHIP_BUSTYPE_SPI;


--
http://www.hailfinger.org/


_______________________________________________
flashrom mailing list
flashrom@flashrom.org
http://www.flashrom.org/mailman/listinfo/flashrom