flashrom v0.9.4-r1452 on MS-DOS 7 (i686), built with libpci 3.1.5, GCC 4.3.2, little endian
flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OS timer resolution is 50000 usecs, 2689M loops per second, delay more than 10% too short (got 88% of expected delay), recalculating... 3202M loops per second, 10 myus = 0 us, 100 myus = 0 us, 1000 myus = 0 us, 10000 myus = 50000 us, 200000 myus = 220000 us, OK.
Initializing internal programmer
No coreboot table found.
DMI string system-manufacturer: ""
DMI string system-product-name: ""
DMI string system-version: ""
DMI string baseboard-manufacturer: ""
DMI string baseboard-product-name: ""
DMI string baseboard-version: ""
DMI string chassis-type: ""
DMI chassis-type is not specific enough.
Found chipset "Intel ICH9R" with PCI ID 8086:2916. Enabling flash write... 
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode disabled
0xffe00000/0xffa00000 FWH decode disabled
0xffd80000/0xff980000 FWH decode disabled
0xffd00000/0xff900000 FWH decode disabled
0xffc80000/0xff880000 FWH decode disabled
0xffc00000/0xff800000 FWH decode disabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x100000 bytes
BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x2

Root Complex Register Block address = 0xfeda8000
GCS = 0x800460: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI)
Top Swap : not enabled
SPIBAR = 0xfeda8000 + 0x3800
0x04: 0x8000 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=0, SCIP=0, FDOPSS=0, FDV=0, FLOCKDN=1
WARNING: SPI Configuration Lockdown activated.
0x06: 0x0000 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0
0x08: 0x0000ffc0 (FADDR)
0x50: 0x0000ffff (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff
0x54: 0x00001fff (FREG0: Flash Descriptor)
Flash Descriptor region is unused.
0x58: 0x00001fff (FREG1: BIOS)
BIOS region is unused.
0x5C: 0x00001fff (FREG2: Management Engine)
Management Engine region is unused.
0x60: 0x00001fff (FREG3: Gigabit Ethernet)
Gigabit Ethernet region is unused.
0x64: 0x00001fff (FREG4: Platform Data)
Platform Data region is unused.
0x74: 0x00000000 (PR0, unused)
0x78: 0x00000000 (PR1, unused)
0x7C: 0x00000000 (PR2, unused)
0x80: 0x00000000 (PR3, unused)
0x84: 0x00000000 (PR4, unused)
0x90: 0x04 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0x007f54 (SSFC)
SSFC: SCGO=0, ACS=1, SPOP=0, COP=5, DBC=63, SME=0, SCF=0
0x94: 0x0606     (PREOP)
0x96: 0x4fc8     (OPTYPE)
0x98: 0x029fabab (OPMENU)
0x9C: 0x01050220 (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00000000 (LVSCC)
LVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=0
0xC8: 0x00000000 (UVSCC)
UVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=0
0xD0: 0x00000000 (FPB)

Reading OPCODES... done
        OP        Type      Pre-OP
op[0]: 0xab, read  w/o addr, none
op[1]: 0xab, read  w/  addr, none
op[2]: 0x9f, read  w/o addr, none
op[3]: 0x02, write w/  addr, none
op[4]: 0x20, write w/  addr, none
op[5]: 0x02, write w/  addr, none
op[6]: 0x05, read  w/o addr, none
op[7]: 0x01, write w/o addr, none
Pre-OP 0: 0x06, Pre-OP 1: 0x06
SPI Read Configuration: prefetching disabled, caching enabled, OK.
This chipset supports the following protocols: FWH, SPI.
Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0x1f, id2 0x4501
Chip status register is 10
Found Atmel flash chip "AT25DF081A" (1024 kB, SPI) at physical address 0xfff00000.
Ignoring security lockdown (if present)
Ignoring status register byte 2
Chip status register is 10
Chip status register: Sector Protection Register Lock (SRPL) is not set
Chip status register: Bit 6 is not set
Chip status register: Erase/Program Error (EPE) is not set
Chip status register: WP# pin (WPP) is not asserted
Chip status register: Software Protection Status (SWP): no sectors are protected
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
===
This flash part has status UNTESTED for operations: PROBE READ ERASE WRITE
The test status of this chip may have been updated in the latest development
version of flashrom. If you are running the latest development version,
please email a report to flashrom@flashrom.org if any of the above operations
work correctly for you with this flash part. Please include the flashrom
output with the additional -V option for all operations you tested (-V, -Vr,
-Vw, -VE), and mention which mainboard or programmer you tested.
Please mention your board in the subject line. Thanks for your help!
Ignoring security lockdown (if present)
Reading flash... Invalid OPCODE 0x03, will not execute.
FAILED.
Restoring MMIO space at fe9ab8a0
Restoring PCI config space for 00:1f:0 reg 0xdc