flashrom v0.9.8-r1888 on Linux 4.3.3 (x86_64)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.4.0, GCC 5.3.0, little endian
Command line (5 args): ./flashrom --read testje.rom --programmer internal --verbose
Calibrating delay loop... OS timer resolution is 1 usecs, 2089M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1001 us, 10000 myus = 10002 us, 4 myus = 4 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
No DMI table found.
Found chipset "Intel Broadwell U Premium" with PCI ID 8086:9cc3.
This chipset is marked as untested. If you are using an up-to-date version
of flashrom *and* were (not) able to successfully update your firmware with it,
then please email a report to flashrom@flashrom.org including a verbose (-V) log.
Thank you!
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0x61: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x0 (LPC)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x1
0xffe00000/0xffa00000 FWH IDSEL: 0x1
0xffd80000/0xff980000 FWH IDSEL: 0x2
0xffd00000/0xff900000 FWH IDSEL: 0x2
0xffc80000/0xff880000 FWH IDSEL: 0x3
0xffc00000/0xff800000 FWH IDSEL: 0x3
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode enabled
0xff600000/0xff200000 FWH decode enabled
0xff500000/0xff100000 FWH decode enabled
0xff400000/0xff000000 FWH decode enabled
Maximum FWH chip size: 0x100000 bytes
SPI Read Configuration: prefetching enabled, caching enabled, 
BIOS_CNTL = 0x2a: BIOS Lock Enable: enabled, BIOS Write Enable: disabled
SPIBAR = 0x00007fdc45bd2000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Reading OPCODES... done
0x06: 0x3f00 (HSFC)
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
0x50: 0x00004a4b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x4a, BRRA 0x4b
0x54: 0x00000000 0x58: 0x07ff01a0 FREG1: BIOS region (0x001a0000-0x007fffff) is read-write.
0x5C: 0x019f0003 0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0xc0 (SSFS)
SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0
0x91: 0xfc4210 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=1, DBC=2, SME=0, SCF=4
0x94: 0x0006     (PREOP)
0x96: 0x843b     (OPTYPE)
0x98: 0x05203b02 (OPMENU)
0x9C: 0x5a00019f (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x80802045 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=1
0xC8: 0x00002045 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x50444653 (FPB)
Enabling hardware sequencing because some important opcode is locked.
PROBLEMS, continuing anyway
The following protocols are supported: FWH, Programmer-specific.
Probing for Programmer Opaque flash chip, 0 kB: Hardware sequencing reports 1 attached SPI flash chip with a density of 8192 kB.
The first partition ranges from 0x000000 to 0x652fff.
In that range are 1619 erase blocks with 4096 B each.
The second partition ranges from 0x653000 to 0x7fffff.
In that range are 429 erase blocks with 4096 B each.
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific) mapped at physical address 0x0000000000000000.
Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Atmel AT49LH00B4, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Atmel AT49LH004, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0x07, id2 0x09, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0x07, id2 0x09, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x00, id2 0x00, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x56, id2 0x1f, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content
Found Programmer flash chip "Opaque flash chip" (8192 kB, Programmer-specific).
Reading flash... Reading 8388608 bytes starting at 0x000000.
HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0
FAILED.
Restoring MMIO space at 0x7fdc45bd58a0
Restoring PCI config space for 00:1f:0 reg 0xdc