[root@localhost ~]# flashrom -r current.bios -V

flashrom v0.9.5.2-r1530 on Linux 2.6.32-573.el6.x86_64 (x86_64), built with libpci 3.1.4, GCC 4.4.6 20110731 (Red Hat 4.4.6-3), little endian

flashrom is free software, get the source code at http://www.flashrom.org

Calibrating delay loop... OS timer resolution is 1 usecs, 2496M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 1009 us, 10000 myus = 10006 us, 4 myus = 4 us, OK.

Initializing internal programmer

No coreboot table found.

DMI string system-manufacturer: "                                "

DMI string system-product-name: "                                "

DMI string system-version: "                        "

DMI string baseboard-manufacturer: "Intel Corporation"

DMI string baseboard-product-name: "DP35DP"

DMI string baseboard-version: "AAD81073-209"

DMI string chassis-type: "Desktop"

Found chipset "Intel ICH9R" with PCI ID 8086:2916. Enabling flash write... 

0xfff80000/0xffb80000 FWH IDSEL: 0x0

0xfff00000/0xffb00000 FWH IDSEL: 0x0

0xffe80000/0xffa80000 FWH IDSEL: 0x1

0xffe00000/0xffa00000 FWH IDSEL: 0x1

0xffd80000/0xff980000 FWH IDSEL: 0x2

0xffd00000/0xff900000 FWH IDSEL: 0x2

0xffc80000/0xff880000 FWH IDSEL: 0x3

0xffc00000/0xff800000 FWH IDSEL: 0x3

0xff700000/0xff300000 FWH IDSEL: 0x4

0xff600000/0xff200000 FWH IDSEL: 0x5

0xff500000/0xff100000 FWH IDSEL: 0x6

0xff400000/0xff000000 FWH IDSEL: 0x7

0xfff80000/0xffb80000 FWH decode enabled

0xfff00000/0xffb00000 FWH decode enabled

0xffe80000/0xffa80000 FWH decode enabled

0xffe00000/0xffa00000 FWH decode enabled

0xffd80000/0xff980000 FWH decode enabled

0xffd00000/0xff900000 FWH decode enabled

0xffc80000/0xff880000 FWH decode enabled

0xffc00000/0xff800000 FWH decode enabled

0xff700000/0xff300000 FWH decode disabled

0xff600000/0xff200000 FWH decode disabled

0xff500000/0xff100000 FWH decode disabled

0xff400000/0xff000000 FWH decode disabled

Maximum FWH chip size: 0x100000 bytes

BIOS Lock Enable: enabled, BIOS Write Enable: disabled, BIOS_CNTL is 0xa

WARNING: Setting 0xdc from 0xa to 0xb on ICH9R failed. New value is 0xa.

Root Complex Register Block address = 0xfed1c000

GCS = 0x1464: BIOS Interface Lock-Down: disabled, Boot BIOS Straps: 0x1 (SPI)

Top Swap : not enabled

SPIBAR = 0xfed1c000 + 0x3800

0x04: 0xe008 (HSFS)

HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1

WARNING: SPI Configuration Lockdown activated.

Reading OPCODES... done

0x06: 0x2f00 (HSFC)

HSFC: FGO=0, FCYCLE=0, FDBC=47, SME=0

0x08: 0x00000000 (FADDR)

0x50: 0x00000a0b (FRAP)

BMWAG 0x00, BMRAG 0x00, BRWA 0x0a, BRRA 0x0b

0x54: 0x00000000 FREG0: WARNING: Flash Descriptor region (0x00000000-0x00000fff) is read-only.

0x58: 0x00ff0035 FREG1: BIOS region (0x00035000-0x000fffff) is read-write.

0x5C: 0x00340003 FREG2: WARNING: Management Engine region (0x00003000-0x00034fff) is locked.

0x60: 0x00020001 FREG3: Gigabit Ethernet region (0x00001000-0x00002fff) is read-write.

Please send a verbose log to flashrom@flashrom.org if this board is not listed on

http://flashrom.org/Supported_hardware#Supported_mainboards yet.

Writes have been disabled. You can enforce write support with the

ich_spi_force programmer option, but it will most likely harm your hardware!

If you force flashrom you will get no support if something breaks.

0x90: 0x00 (SSFS)

SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0

0x91: 0x004200 (SSFC)

SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=2, SME=0, SCF=0

0x94: 0x0006     (PREOP)

0x96: 0x0008     (OPTYPE)

0x98: 0x0000ab9f (OPMENU)

0x9C: 0x00000000 (OPMENU+4)

0xA0: 0x00000000 (BBAR)

0xC4: 0x00002009 (LVSCC)

LVSCC: BES=0x1, WG=0, WSR=1, WEWS=0, EO=0x20, VCL=0

0xC8: 0x00002009 (UVSCC)

UVSCC: BES=0x1, WG=0, WSR=1, WEWS=0, EO=0x20, VCL=0

0xD0: 0x00000000 (FPB)

Enabling hardware sequencing because some important opcode is locked.

SPI Read Configuration: prefetching enabled, caching enabled, PROBLEMS, continuing anyway

The following protocols are supported: FWH, Programmer-specific.

Probing for Programmer Opaque flash chip, 0 kB: Found 1 attached SPI flash chip with a density of 1024 kB.

There is only one partition containing the whole address space (0x000000 - 0x0fffff).

There are 256 erase blocks with 4096 B each.

Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific) at physical address 0x0.

Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0x67, id2 0x21, id1 is normal flash content, id2 is normal flash content

Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0x67, id2 0x21, id1 is normal flash content, id2 is normal flash content

Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0x67, id2 0x21, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x38, id2 0x85, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0x67, id2 0x21, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0x67, id2 0x21, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content

Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0x1a, id2 0x9e, id1 is normal flash content, id2 is normal flash content

Found Programmer flash chip "Opaque flash chip" (1024 kB, Programmer-specific).

Reading flash... Reading 1048576 bytes starting at 0x000000.

Transaction error between offset 0x00003000 and 0x0000303f (= 0x00003000 + 63)!

HSFS: FDONE=1, FCERR=1, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1

HSFC: FGO=0, FCYCLE=0, FDBC=63, SME=0

Read operation failed!

FAILED.

Restoring MMIO space at 0x7fb2d7a0e8a0

Restoring PCI config space for 00:1f:0 reg 0xdc

[root@localhost ~]# 

_______________________________________________
flashrom mailing list
flashrom@flashrom.org
http://www.flashrom.org/mailman/listinfo/flashrom