David Hendricks submitted this change.

View Change

Approvals: build bot (Jenkins): Verified Angel Pons: Looks good to me, approved
ft2232_spi: Add support for Tin Can Tools Flyswatter/Flyswatter 2

The Tin Can Tools Flyswatter and Flyswatter 2 have a FT2232H
with a JTAG interface wired to port A. The buffers that drive the
JTAG pins need to be enabled with an nOE signal from the
FT2232H ADBUS6 and ADBUS7 pins.

Flyswatter has an ARM-14 JTAG interface and Flyswatter 2 has
an ARM-20 JTAG interface.

Change-Id: I56b1fb76dcda32bb02980cd54a2853506bfc9dfd
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Reviewed-on: https://review.coreboot.org/c/flashrom/+/36896
Tested-by: build bot (Jenkins) <no-reply@coreboot.org>
Reviewed-by: Angel Pons <th3fanbus@gmail.com>
---
M flashrom.8.tmpl
M ft2232_spi.c
2 files changed, 8 insertions(+), 1 deletion(-)

diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl
index 27f3846..8ef2cbf 100644
--- a/flashrom.8.tmpl
+++ b/flashrom.8.tmpl
@@ -758,7 +758,8 @@
This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design
DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster,
Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB
-Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2.
+Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP, Google Servo v1/v2 and Tin Can Tools
+Flyswatter/Flyswatter 2.
.sp
An optional parameter specifies the controller
type, channel/interface/port and GPIO-based chip select it should support. For that you have to use the
diff --git a/ft2232_spi.c b/ft2232_spi.c
index 34b43dd..5bdc2a7 100644
--- a/ft2232_spi.c
+++ b/ft2232_spi.c
@@ -269,6 +269,12 @@
} else if (!strcasecmp(arg, "google-servo-v2-legacy")) {
ft2232_vid = GOOGLE_VID;
ft2232_type = GOOGLE_SERVO_V2_PID0;
+ } else if (!strcasecmp(arg, "flyswatter")) {
+ ft2232_type = FTDI_FT2232H_PID;
+ channel_count = 2;
+ /* Flyswatter and Flyswatter-2 require GPIO bits 0x80
+ * and 0x40 to be driven low to enable output buffers */
+ pindir = 0xcb;
} else {
msg_perr("Error: Invalid device type specified.\n");
free(arg);

To view, visit change 36896. To unsubscribe, or for help writing mail filters, visit settings.

Gerrit-Project: flashrom
Gerrit-Branch: master
Gerrit-Change-Id: I56b1fb76dcda32bb02980cd54a2853506bfc9dfd
Gerrit-Change-Number: 36896
Gerrit-PatchSet: 3
Gerrit-Owner: David Hendricks <david.hendricks@gmail.com>
Gerrit-Reviewer: Angel Pons <th3fanbus@gmail.com>
Gerrit-Reviewer: David Hendricks <david.hendricks@gmail.com>
Gerrit-Reviewer: Nico Huber <nico.h@gmx.de>
Gerrit-Reviewer: build bot (Jenkins) <no-reply@coreboot.org>
Gerrit-MessageType: merged