Here is a dump trying to boot using SeaBIOS with addition SeaBIOS debug enabled. Also switched from using mainboard "QEMU x86 q35/ich9" to "QEMU x86 i440fx/piix4", but that didn't help.
# qemu-system-i386 -M pc -bios build/coreboot.rom -hda /work/disk.img -cdrom images/Fedora-Live-Workstation-x86_64-22-3.iso -serial stdio -boot d WARNING: Image format was not specified for '/work/disk.img' and probing guessed raw. Automatically detecting the format is dangerous for raw images, write operations on block 0 will be restricted. Specify the 'raw' format explicitly to remove the restrictions.
coreboot-4.1-6cb3a59fd5e754c3627b79db21c5bcc284bfd721 Wed Aug 12 23:18:11 UTC 2015 romstage starting... CBMEM: IMD: root @ 07fff000 254 entries. IMD: root @ 07ffec00 62 entries. CBFS provider active. CBFS @ 0 size 7ffc40 CBFS: Locating 'fallback/ramstage' CBFS: Found @ offset 4100 size 9c1a 'fallback/ramstage' located at offset: 4138 size: 9c1a
coreboot-4.1-6cb3a59fd5e754c3627b79db21c5bcc284bfd721 Wed Aug 12 23:18:11 UTC 2015 ramstage starting... Moving GDT to 07ffe9c0...ok Enumerating buses... Show all devs... Before device enumeration. Root Device: enabled 1 CPU_CLUSTER: 0: enabled 1 APIC: 00: enabled 1 DOMAIN: 0000: enabled 1 PCI: 00:00.0: enabled 1 PCI: 00:01.0: enabled 1 PCI: 00:01.1: enabled 1 PCI: 00:01.3: enabled 1 Compare with tree... Root Device: enabled 1 CPU_CLUSTER: 0: enabled 1 APIC: 00: enabled 1 DOMAIN: 0000: enabled 1 PCI: 00:00.0: enabled 1 PCI: 00:01.0: enabled 1 PCI: 00:01.1: enabled 1 PCI: 00:01.3: enabled 1 Root Device scanning... root_dev_scan_bus for Root Device CPU_CLUSTER: 0 enabled DOMAIN: 0000 enabled CPU_CLUSTER: 0 scanning... QEMU: firmware config interface detected QEMU: max_cpus is 1 CPU: APIC: 00 enabled DOMAIN: 0000 scanning... PCI: pci_scan_bus for bus 00 PCI: 00:00.0 [8086/1237] ops PCI: 00:00.0 [8086/1237] enabled PCI: 00:01.0 [8086/7000] bus ops PCI: 00:01.0 [8086/7000] enabled PCI: 00:01.1 [8086/7010] ops PCI: 00:01.1 [8086/7010] enabled PCI: 00:01.3 [8086/7113] bus ops PCI: 00:01.3 [8086/7113] enabled PCI: 00:02.0 [1234/1111] ops PCI: 00:02.0 [1234/1111] enabled PCI: 00:03.0 [8086/100e] enabled PCI: 00:01.0 scanning... scan_lpc_bus for PCI: 00:01.0 scan_lpc_bus for PCI: 00:01.0 done PCI: 00:01.3 scanning... scan_smbus for PCI: 00:01.3 scan_smbus for PCI: 00:01.3 done root_dev_scan_bus for Root Device done done found VGA at PCI: 00:02.0 Setting up VGA for PCI: 00:02.0 Setting PCI_BRIDGE_CTL_VGA for bridge DOMAIN: 0000 Setting PCI_BRIDGE_CTL_VGA for bridge Root Device Allocating resources... Reading resources... Root Device read_resources bus 0 link: 0 CPU_CLUSTER: 0 read_resources bus 0 link: 0 APIC: 00 missing read_resources CPU_CLUSTER: 0 read_resources bus 0 link: 0 done QEMU: 11 files in fw_cfg QEMU: etc/boot-fail-wait [size=4] QEMU: etc/smbios/smbios-tables [size=320] QEMU: etc/smbios/smbios-anchor [size=31] QEMU: etc/e820 [size=20] QEMU: genroms/kvmvapic.bin [size=9216] QEMU: etc/system-states [size=6] QEMU: etc/acpi/tables [size=131072] QEMU: etc/table-loader [size=4096] QEMU: etc/tpm/log [size=0] QEMU: etc/acpi/rsdp [size=36] QEMU: bootorder [size=0] QEMU: e820/ram: 0x00000000 +0x08000000 QEMU: reserve ioports 0x0510-0x0511 [firmware-config] QEMU: reserve ioports 0x5658-0x5658 [vmware-port] QEMU: reserve ioports 0xae00-0xae0f [pci-hotplug] QEMU: reserve ioports 0xaf00-0xaf1f [cpu-hotplug] QEMU: reserve ioports 0xafe0-0xafe3 [piix4-gpe0] DOMAIN: 0000 read_resources bus 0 link: 0 DOMAIN: 0000 read_resources bus 0 link: 0 done Root Device read_resources bus 0 link: 0 done Done reading resources. Show resources in subtree (Root Device)...After reading. Root Device child on link 0 CPU_CLUSTER: 0 CPU_CLUSTER: 0 child on link 0 APIC: 00 APIC: 00 DOMAIN: 0000 child on link 0 PCI: 00:00.0 DOMAIN: 0000 resource base 0 size 0 align 0 gran 0 limit ffff flags 40040100 index 10000000 DOMAIN: 0000 resource base 0 size 0 align 0 gran 0 limit ffffffff flags 40040200 index 10000100 DOMAIN: 0000 resource base 0 size a0000 align 0 gran 0 limit 0 flags e0004200 index a DOMAIN: 0000 resource base c0000 size 7f40000 align 0 gran 0 limit 0 flags e0004200 index b DOMAIN: 0000 resource base 510 size 2 align 0 gran 0 limit ffff flags e0000100 index c DOMAIN: 0000 resource base 5658 size 1 align 0 gran 0 limit ffff flags e0000100 index d DOMAIN: 0000 resource base ae00 size 10 align 0 gran 0 limit ffff flags e0000100 index e DOMAIN: 0000 resource base af00 size 20 align 0 gran 0 limit ffff flags e0000100 index f DOMAIN: 0000 resource base afe0 size 4 align 0 gran 0 limit ffff flags e0000100 index 10 DOMAIN: 0000 resource base fec00000 size 100000 align 0 gran 0 limit ffffffff flags e0000200 index 2 DOMAIN: 0000 resource base fee00000 size 10000 align 0 gran 0 limit ffffffff flags e0000200 index 3 PCI: 00:00.0 PCI: 00:01.0 PCI: 00:01.0 resource base 0 size 1000 align 0 gran 0 limit ffff flags c0000100 index 1 PCI: 00:01.0 resource base ff800000 size 800000 align 0 gran 0 limit 0 flags d0000200 index 2 PCI: 00:01.1 PCI: 00:01.1 resource base 0 size 10 align 4 gran 4 limit ffff flags 100 index 20 PCI: 00:01.3 PCI: 00:01.3 resource base e400 size 40 align 0 gran 0 limit ffff flags d0000100 index 1 PCI: 00:01.3 resource base f00 size 10 align 0 gran 0 limit ffff flags d0000100 index 2 PCI: 00:02.0 PCI: 00:02.0 resource base 0 size 1000000 align 24 gran 24 limit ffffffff flags 1200 index 10 PCI: 00:02.0 resource base 0 size 1000 align 12 gran 12 limit ffffffff flags 200 index 18 PCI: 00:02.0 resource base 0 size 10000 align 16 gran 16 limit ffffffff flags 2200 index 30 PCI: 00:03.0 PCI: 00:03.0 resource base 0 size 20000 align 17 gran 17 limit ffffffff flags 200 index 10 PCI: 00:03.0 resource base 0 size 40 align 6 gran 6 limit ffff flags 100 index 14 PCI: 00:03.0 resource base 0 size 40000 align 18 gran 18 limit ffffffff flags 2200 index 30 DOMAIN: 0000 io: base: 0 size: 0 align: 0 gran: 0 limit: ffff PCI: 00:03.0 14 * [0x0 - 0x3f] io PCI: 00:01.1 20 * [0x40 - 0x4f] io DOMAIN: 0000 io: base: 50 size: 50 align: 6 gran: 0 limit: ffff done DOMAIN: 0000 mem: base: 0 size: 0 align: 0 gran: 0 limit: ffffffff PCI: 00:02.0 10 * [0x0 - 0xffffff] prefmem PCI: 00:03.0 30 * [0x1000000 - 0x103ffff] mem PCI: 00:03.0 10 * [0x1040000 - 0x105ffff] mem PCI: 00:02.0 30 * [0x1060000 - 0x106ffff] mem PCI: 00:02.0 18 * [0x1070000 - 0x1070fff] mem DOMAIN: 0000 mem: base: 1071000 size: 1071000 align: 24 gran: 0 limit: ffffffff done avoid_fixed_resources: DOMAIN: 0000 avoid_fixed_resources:@DOMAIN: 0000 10000000 limit 0000ffff avoid_fixed_resources:@DOMAIN: 0000 10000100 limit ffffffff constrain_resources: DOMAIN: 0000 0a base 00000000 limit 0009ffff mem (fixed) constrain_resources: DOMAIN: 0000 0b base 000c0000 limit 07ffffff mem (fixed) constrain_resources: DOMAIN: 0000 0c base 00000510 limit 00000511 io (fixed) constrain_resources: DOMAIN: 0000 0d base 00005658 limit 00005658 io (fixed) constrain_resources: DOMAIN: 0000 0e base 0000ae00 limit 0000ae0f io (fixed) constrain_resources: DOMAIN: 0000 02 base fec00000 limit fecfffff mem (fixed) avoid_fixed_resources:@DOMAIN: 0000 10000000 base 00005659 limit 0000adff avoid_fixed_resources:@DOMAIN: 0000 10000100 base fd000000 limit febfffff Setting resources... DOMAIN: 0000 io: base:5659 size:50 align:6 gran:0 limit:adff PCI: 00:03.0 14 * [0x5800 - 0x583f] io PCI: 00:01.1 20 * [0x5840 - 0x584f] io DOMAIN: 0000 io: next_base: 5850 size: 50 align: 6 gran: 0 done DOMAIN: 0000 mem: base:fd000000 size:1071000 align:24 gran:0 limit:febfffff PCI: 00:02.0 10 * [0xfd000000 - 0xfdffffff] prefmem PCI: 00:03.0 30 * [0xfe000000 - 0xfe03ffff] mem PCI: 00:03.0 10 * [0xfe040000 - 0xfe05ffff] mem PCI: 00:02.0 30 * [0xfe060000 - 0xfe06ffff] mem PCI: 00:02.0 18 * [0xfe070000 - 0xfe070fff] mem DOMAIN: 0000 mem: next_base: fe071000 size: 1071000 align: 24 gran: 0 done Root Device assign_resources, bus 0 link: 0 DOMAIN: 0000 assign_resources, bus 0 link: 0 PCI: 00:01.1 20 <- [0x0000005840 - 0x000000584f] size 0x00000010 gran 0x04 io PCI: 00:02.0 10 <- [0x00fd000000 - 0x00fdffffff] size 0x01000000 gran 0x18 prefmem PCI: 00:02.0 18 <- [0x00fe070000 - 0x00fe070fff] size 0x00001000 gran 0x0c mem PCI: 00:02.0 30 <- [0x00fe060000 - 0x00fe06ffff] size 0x00010000 gran 0x10 romem PCI: 00:03.0 10 <- [0x00fe040000 - 0x00fe05ffff] size 0x00020000 gran 0x11 mem PCI: 00:03.0 14 <- [0x0000005800 - 0x000000583f] size 0x00000040 gran 0x06 io PCI: 00:03.0 30 <- [0x00fe000000 - 0x00fe03ffff] size 0x00040000 gran 0x12 romem DOMAIN: 0000 assign_resources, bus 0 link: 0 Root Device assign_resources, bus 0 link: 0 Done setting resources. Show resources in subtree (Root Device)...After assigning values. Root Device child on link 0 CPU_CLUSTER: 0 CPU_CLUSTER: 0 child on link 0 APIC: 00 APIC: 00 DOMAIN: 0000 child on link 0 PCI: 00:00.0 DOMAIN: 0000 resource base 5659 size 50 align 6 gran 0 limit adff flags 40040100 index 10000000 DOMAIN: 0000 resource base fd000000 size 1071000 align 24 gran 0 limit febfffff flags 40040200 index 10000100 DOMAIN: 0000 resource base 0 size a0000 align 0 gran 0 limit 0 flags e0004200 index a DOMAIN: 0000 resource base c0000 size 7f40000 align 0 gran 0 limit 0 flags e0004200 index b DOMAIN: 0000 resource base 510 size 2 align 0 gran 0 limit ffff flags e0000100 index c DOMAIN: 0000 resource base 5658 size 1 align 0 gran 0 limit ffff flags e0000100 index d DOMAIN: 0000 resource base ae00 size 10 align 0 gran 0 limit ffff flags e0000100 index e DOMAIN: 0000 resource base af00 size 20 align 0 gran 0 limit ffff flags e0000100 index f DOMAIN: 0000 resource base afe0 size 4 align 0 gran 0 limit ffff flags e0000100 index 10 DOMAIN: 0000 resource base fec00000 size 100000 align 0 gran 0 limit ffffffff flags e0000200 index 2 DOMAIN: 0000 resource base fee00000 size 10000 align 0 gran 0 limit ffffffff flags e0000200 index 3 PCI: 00:00.0 PCI: 00:01.0 PCI: 00:01.0 resource base 0 size 1000 align 0 gran 0 limit ffff flags c0000100 index 1 PCI: 00:01.0 resource base ff800000 size 800000 align 0 gran 0 limit 0 flags d0000200 index 2 PCI: 00:01.1 PCI: 00:01.1 resource base 5840 size 10 align 4 gran 4 limit 584f flags 60000100 index 20 PCI: 00:01.3 PCI: 00:01.3 resource base e400 size 40 align 0 gran 0 limit ffff flags d0000100 index 1 PCI: 00:01.3 resource base f00 size 10 align 0 gran 0 limit ffff flags d0000100 index 2 PCI: 00:02.0 PCI: 00:02.0 resource base fd000000 size 1000000 align 24 gran 24 limit fdffffff flags 60001200 index 10 PCI: 00:02.0 resource base fe070000 size 1000 align 12 gran 12 limit fe070fff flags 60000200 index 18 PCI: 00:02.0 resource base fe060000 size 10000 align 16 gran 16 limit fe06ffff flags 60002200 index 30 PCI: 00:03.0 PCI: 00:03.0 resource base fe040000 size 20000 align 17 gran 17 limit fe05ffff flags 60000200 index 10 PCI: 00:03.0 resource base 5800 size 40 align 6 gran 6 limit 583f flags 60000100 index 14 PCI: 00:03.0 resource base fe000000 size 40000 align 18 gran 18 limit fe03ffff flags 60002200 index 30 Done allocating resources. Enabling resources... PCI: 00:00.0 cmd <- 00 PCI: 00:01.0 cmd <- 00 PCI: 00:01.1 cmd <- 01 PCI: 00:01.3 cmd <- 00 PCI: 00:02.0 cmd <- 03 PCI: 00:03.0 cmd <- 03 done. Initializing devices... Root Device init ... CPU_CLUSTER: 0 init ... Initializing CPU #0 CPU: vendor Intel device 663 CPU: family 06, model 06, stepping 03 CPU #0 initialized PCI: 00:00.0 init ... Keyboard init... Assigning IRQ 10 to 0:1.3 Assigning IRQ 11 to 0:3.0 PCI: 00:01.0 init ... RTC Init PCI: 00:01.1 init ... IDE: Primary IDE interface: on IDE: Secondary IDE interface: on IDE: Access to legacy IDE ports: off PCI: 00:02.0 init ... PCI: 00:03.0 init ... Devices initialized Show all devs... After init. Root Device: enabled 1 CPU_CLUSTER: 0: enabled 1 APIC: 00: enabled 1 DOMAIN: 0000: enabled 1 PCI: 00:00.0: enabled 1 PCI: 00:01.0: enabled 1 PCI: 00:01.1: enabled 1 PCI: 00:01.3: enabled 1 PCI: 00:02.0: enabled 1 PCI: 00:03.0: enabled 1 CPU: 00: enabled 1 Finalize devices... Devices finalized QEMU: found acpi tables in fw_cfg. QEMU: loading "etc/acpi/rsdp" to 0x7fda000 (len 36) QEMU: loading "etc/acpi/tables" to 0x7fda040 (len 131072) QEMU: loaded acpi tables from fw_cfg. ACPI tables: 131136 bytes. smbios_write_tables: 07fd9000 Root Device (Emulation QEMU x86 i440fx/piix4) CPU_CLUSTER: 0 (QEMU Northbridge i440fx) APIC: 00 (unknown) DOMAIN: 0000 (QEMU Northbridge i440fx) QEMU: found smbios tables in fw_cfg (len 320). QEMU: coreboot type0 table found at 0x7fd9020. QEMU: loading smbios tables to 0x7fd907a PCI: 00:00.0 (QEMU Northbridge i440fx) PCI: 00:01.0 (Intel 82371FB/SB/MX/AB/EB/MB Southbridge) PCI: 00:01.1 (Intel 82371FB/SB/MX/AB/EB/MB Southbridge) PCI: 00:01.3 (Intel 82371FB/SB/MX/AB/EB/MB Southbridge) PCI: 00:02.0 (unknown) PCI: 00:03.0 (unknown) CPU: 00 (unknown) SMBIOS tables: 442 bytes. Writing table forward entry at 0x00000500 Wrote coreboot table at: 00000500, 0x10 bytes, checksum e7e1 Table forward entry ends at 0x00000528. ... aligned to 0x00001000 Writing coreboot table at 0x07fd1000 rom_table_end = 0x07fd1000 ... aligned to 0x07fe0000 0. 0000000000000000-0000000000000fff: CONFIGURATION TABLES 1. 0000000000001000-000000000009ffff: RAM 2. 00000000000c0000-0000000007fd0fff: RAM 3. 0000000007fd1000-0000000007ffffff: CONFIGURATION TABLES 4. 00000000ff800000-00000000ffffffff: RESERVED Wrote coreboot table at: 07fd1000, 0x148 bytes, checksum 3955 coreboot table: 352 bytes. IMD ROOT 0. 07fff000 00001000 IMD SMALL 1. 07ffe000 00001000 ACPI 2. 07fda000 00024000 SMBIOS 3. 07fd9000 00000800 COREBOOT 4. 07fd1000 00008000 IMD small region: IMD ROOT 0. 07ffec00 00000400 CAR GLOBALS 1. 07ffebe0 00000004 ROMSTAGE 2. 07ffebc0 00000004 GDT 3. 07ffe9c0 00000200 CBFS provider active. CBFS @ 0 size 7ffc40 CBFS: Locating 'fallback/payload' CBFS: Found @ offset dd80 size ed3e 'fallback/payload' located at offset: ddb8 size: ed3e Loading segment from rom address 0xff80ddb8 code (compression=1) New segment dstaddr 0xe2bd8 memsize 0x1d428 srcaddr 0xff80ddf0 filesize 0xed06 Loading segment from rom address 0xff80ddd4 Entry Point 0x000fcbd3 Bounce Buffer at 07f94000, 245848 bytes Loading Segment: addr: 0x00000000000e2bd8 memsz: 0x000000000001d428 filesz: 0x000000000000ed06 lb: [0x0000000000100000, 0x000000000011e02c) Post relocation: addr: 0x00000000000e2bd8 memsz: 0x000000000001d428 filesz: 0x000000000000ed06 using LZMA [ 0x000e2bd8, 00100000, 0x00100000) <- ff80ddf0 dest 000e2bd8, end 00100000, bouncebuffer 7f94000 Loaded segments Jumping to boot code at 000fcbd3(07fd1000) CPU0: stack: 00115000 - 00116000, lowest used address 00115c3c, stack used: 964 bytes entry = 0x000fcbd3 lb_start = 0x00100000 lb_size = 0x0001e02c buffer = 0x07f94000 SeaBIOS (version unknown) Running on QEMU (i440fx) Attempting to find coreboot table Found coreboot table forwarder. Now attempting to find coreboot memory map Add to e820 map: 00000000 00001000 2 Add to e820 map: 00001000 0009f000 1 Add to e820 map: 000c0000 07f11000 1 Add to e820 map: 07fd1000 0002f000 2 Add to e820 map: ff800000 00800000 2 Add to e820 map: 00000000 00004000 1 Found mainboard Emulation QEMU x86 i440fx/piix4 malloc preinit Add to e820 map: 000a0000 00050000 -1 Add to e820 map: 000f0000 00010000 2 Add to e820 map: 07f91000 00040000 2 _malloc zone=0x000ed9b0 size=39392 align=10 ret=0x07f87560 (detail=0x07f90f40) Relocating init from 0x000e4040 to 0x07f87560 (size 39392) malloc init Found QEMU fw_cfg _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f87430 (detail=0x07f874d0) Add romfile: etc/boot-fail-wait (size=4) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f87360 (detail=0x07f87400) Add romfile: etc/smbios/smbios-tables (size=320) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f87290 (detail=0x07f87330) Add romfile: etc/smbios/smbios-anchor (size=31) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f871c0 (detail=0x07f87260) Add romfile: etc/e820 (size=20) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f870f0 (detail=0x07f87190) Add romfile: genroms/kvmvapic.bin (size=9216) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f87020 (detail=0x07f870c0) Add romfile: etc/system-states (size=6) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f86f50 (detail=0x07f86ff0) Add romfile: etc/acpi/tables (size=131072) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f86e80 (detail=0x07f86f20) Add romfile: etc/table-loader (size=4096) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f86db0 (detail=0x07f86e50) Add romfile: etc/tpm/log (size=0) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f86ce0 (detail=0x07f86d80) Add romfile: etc/acpi/rsdp (size=36) _malloc zone=0x07f90ed0 size=148 align=10 ret=0x07f86c10 (detail=0x07f86cb0) Add romfile: bootorder (size=0) Moving pm_base to 0x600 Found CBFS header at 0xfffffc20 _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86b40 (detail=0x07f86be0) Add romfile: cmos_layout.bin (size=808) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86a70 (detail=0x07f86b10) Add romfile: fallback/dsdt.aml (size=4000) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f869a0 (detail=0x07f86a40) Add romfile: fallback/romstage (size=11560) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f868d0 (detail=0x07f86970) Add romfile: fallback/ramstage (size=39962) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86800 (detail=0x07f868a0) Add romfile: fallback/payload (size=60734) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86730 (detail=0x07f867d0) Add romfile: config (size=2952) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86660 (detail=0x07f86700) Add romfile: revision (size=621) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f86590 (detail=0x07f86630) Add romfile: bootorder (size=64) _malloc zone=0x07f90ed0 size=156 align=10 ret=0x07f864c0 (detail=0x07f86560) Add romfile: (size=8266200) init ivt init bda Add to e820 map: 0009fc00 00000400 2 _malloc zone=0x07f90ed0 size=65 align=10 ret=0x07f86440 (detail=0x07f86490) Copying romfile 'bootorder' (len 64) Copying data 64@0xff81d9a8 to 64@0x07f86440 _malloc zone=0x07f90ed0 size=12 align=10 ret=0x07f86400 (detail=0x07f86410) boot order: 1: /pci@i0cf8/*@1,1/drive@1/disk@0 2: /pci@i0cf8/*@1,1/drive@0/disk@0 3: init bios32 init PMM init PNPBIOS table init keyboard init mouse init pic math cp init tsc calibrate start=701017369 end=706492732 diff=5475363 CPU Mhz=3190 init timer PCI probe _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f863b0 (detail=0x07f863d0) PCI device 00:00.0 (vd=8086:1237 c=0600) _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f86360 (detail=0x07f86380) PCI device 00:01.0 (vd=8086:7000 c=0601) _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f86310 (detail=0x07f86330) PCI device 00:01.1 (vd=8086:7010 c=0101) _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f862c0 (detail=0x07f862e0) PCI device 00:01.3 (vd=8086:7113 c=0680) _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f86270 (detail=0x07f86290) PCI device 00:02.0 (vd=1234:1111 c=0300) _malloc zone=0x07f90ed0 size=32 align=10 ret=0x07f86220 (detail=0x07f86240) PCI device 00:03.0 (vd=8086:100e c=0200) Found 6 PCI devices (max PCI bus is 00) Relocating coreboot bios tables _malloc zone=0x07f90ed8 size=31 align=10 ret=0x000f5090 (detail=0x07f861f0) Copying SMBIOS entry point from 0x07fd9000 to 0x000f5090 _malloc zone=0x07f90ed8 size=20 align=10 ret=0x000f5070 (detail=0x07f861c0) Copying ACPI RSDP from 0x07fda000 to 0x000f5070 rsdp=0x000f5070 rsdt=0x07fdb6f4 fadt=0x07fdac1a pm_tmr_blk=e408 Using pmtimer, ioport 0xe408 Scan for VGA option rom Attempting to init PCI bdf 00:02.0 (vd 1234:1111) Attempting to map option rom on dev 00:02.0 Option rom sizing returned fe060000 ffff0000 Inspecting possible rom at 0xfe060000 (vd=1234:1111 bdf=00:02.0) Copying option rom (size 38400) from 0xfe060000 to 0x000c0000 Checking rom 0x000c0000 (sig aa55 size 75) Running option rom at c000:0003 pmm call arg1=0 pmm00: length=20 handle=ffffffff flags=9 _malloc zone=0x07f90ee0 size=512 align=10 ret=0x000ecfa0 (detail=0x07f86190) Turning on vga text mode console SeaBIOS (version unknown) _malloc zone=0x07f90ed0 size=4096 align=1000 ret=0x07f85000 (detail=0x07f86160) /07f85000\ Start thread |07f85000| init usb \07f85000/ End thread _free 0x07f85000 (detail=0x07f86160) All threads complete. init ps2port _malloc zone=0x07f90ed0 size=4096 align=1000 ret=0x07f85000 (detail=0x07f86160) /07f85000\ Start thread |07f85000| i8042_flush |07f85000| i8042_command cmd=1aa |07f85000| i8042_wait_write |07f85000| i8042_wait_read |07f85000| i8042 param=55 |07f85000| i8042_command cmd=1ab |07f85000| i8042_wait_write |07f85000| i8042_wait_read |07f85000| i8042 param=0 |07f85000| ps2_command aux=0 cmd=2ff |07f85000| i8042 ctr old=30 new=30 |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write init lpt Found 1 lpt ports init serial Found 1 serial ports init floppy drives init hard drives _malloc zone=0x07f90ed8 size=16 align=10 ret=0x000f5060 (detail=0x07f86130) ATA controller 1 at 1f0/3f4/0 (irq 14 dev 9) _malloc zone=0x07f90ed0 size=4096 align=1000 ret=0x07f84000 (detail=0x07f86100) /07f84000\ Start thread |07f84000| powerup iobase=1f0 st=50 |07f84000| powerup iobase=1f0 st=50 |07f84000| ata_detect ata0-0: sc=55 sn=aa dh=a0 |07f84000| ata_reset drive=0x07f84dc0 |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_sendbyte aux=0 cmd=ff |07f85000| i8042_kbd_write c=255 |07f85000| i8042_wait_write |07f85000| ps2 read fa |07f85000| ps2 read aa _malloc zone=0x07f90ed8 size=16 align=10 ret=0x000f5050 (detail=0x07f860d0) ATA controller 2 at 170/374/0 (irq 15 dev 9) _malloc zone=0x07f90ed0 size=4096 align=1000 ret=0x07f83000 (detail=0x07f860a0) /07f83000\ Start thread |07f83000| powerup iobase=170 st=50 |07f83000| powerup iobase=170 st=50 |07f83000| ata_detect ata1-0: sc=55 sn=aa dh=a0 |07f83000| ata_reset drive=0x07f83dc0 |07f84000| ata_reset exit status=50 |07f84000| send_cmd : read error (status=41 err=04) |07f84000| _malloc zone=0x07f90ed8 size=44 align=10 ret=0x000f5020 (detail=0x07f86070) |07f84000| _malloc zone=0x07f90ed0 size=80 align=10 ret=0x07f82fb0 (detail=0x07f86040) |07f84000| ata0-0: QEMU HARDDISK ATA-7 Hard-Disk (1000 MiBytes) |07f84000| Searching bootorder for: /pci@i0cf8/*@1,1/drive@0/disk@0 |07f84000| _malloc zone=0x07f90ed0 size=24 align=10 ret=0x07f82f90 (detail=0x07f86010) |07f84000| Registering bootable: ata0-0: QEMU HARDDISK ATA-7 Hard-Disk (1000 MiBytes) (type:2 prio:2 data:f5020) |07f84000| ata_detect resetresult=6001 |07f84000| powerup iobase=1f0 st=50 |07f84000| powerup iobase=1f0 st=0 |07f84000| ata_detect ata0-1: sc=55 sn=aa dh=b0 |07f84000| send_cmd : DRQ not set (status 00) \07f84000/ End thread _free 0x07f84000 (detail=0x07f86100) init ahci init virtio-blk init virtio-scsi init lsi53c895a init esp init megasas init pvscsi |07f83000| ata_reset exit status=0 |07f83000| _malloc zone=0x07f90ed8 size=44 align=10 ret=0x000f4ff0 (detail=0x07f86100) |07f83000| _malloc zone=0x07f90ed0 size=80 align=10 ret=0x07f84f80 (detail=0x07f84fd0) |07f83000| DVD/CD [ata1-0: QEMU DVD-ROM ATAPI-4 DVD/CD] |07f83000| Searching bootorder for: /pci@i0cf8/*@1,1/drive@1/disk@0 |07f83000| _malloc zone=0x07f90ed0 size=24 align=10 ret=0x07f84f30 (detail=0x07f84f50) |07f83000| Registering bootable: DVD/CD [ata1-0: QEMU DVD-ROM ATAPI-4 DVD/CD] (type:3 prio:1 data:f4ff0) |07f83000| ata_detect resetresult=0000 |07f83000| powerup iobase=170 st=50 |07f83000| powerup iobase=170 st=0 |07f83000| ata_detect ata1-1: sc=55 sn=aa dh=b0 |07f83000| send_cmd : DRQ not set (status 00) \07f83000/ End thread _free 0x07f83000 (detail=0x07f860a0) |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_command aux=0 cmd=f5 |07f85000| i8042 ctr old=30 new=30 |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_sendbyte aux=0 cmd=f5 |07f85000| i8042_kbd_write c=245 |07f85000| i8042_wait_write |07f85000| ps2 read fa |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_command aux=0 cmd=10f0 |07f85000| i8042 ctr old=30 new=30 |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_sendbyte aux=0 cmd=f0 |07f85000| i8042_kbd_write c=240 |07f85000| i8042_wait_write |07f85000| ps2 read fa |07f85000| ps2_sendbyte aux=0 cmd=2 |07f85000| i8042_kbd_write c=2 |07f85000| i8042_wait_write |07f85000| ps2 read fa |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_command aux=0 cmd=f4 |07f85000| i8042 ctr old=61 new=70 |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| ps2_sendbyte aux=0 cmd=f4 |07f85000| i8042_kbd_write c=244 |07f85000| i8042_wait_write |07f85000| ps2 read fa |07f85000| i8042_command cmd=1060 |07f85000| i8042_wait_write |07f85000| i8042_wait_write |07f85000| PS2 keyboard initialized \07f85000/ End thread _free 0x07f85000 (detail=0x07f86160) All threads complete. Scan for option roms Attempting to init PCI bdf 00:00.0 (vd 8086:1237) Attempting to map option rom on dev 00:00.0 Option rom sizing returned 0 0 Attempting to init PCI bdf 00:01.0 (vd 8086:7000) Attempting to map option rom on dev 00:01.0 Option rom sizing returned 0 0 Attempting to init PCI bdf 00:01.3 (vd 8086:7113) Attempting to map option rom on dev 00:01.3 Option rom sizing returned 0 0 Attempting to init PCI bdf 00:03.0 (vd 8086:100e) Attempting to map option rom on dev 00:03.0 Option rom sizing returned fe000000 fffc0000 Inspecting possible rom at 0xfe000000 (vd=8086:100e bdf=00:03.0) Copying option rom (size 71168) from 0xfe000000 to 0x000c9800 Checking rom 0x000c9800 (sig aa55 size 139) Running option rom at c980:0003 enter handle_pcibios: a=0000b101 b=0000ffff c=00000000 d=0000ffff ds=c980 es=f000 ss=0000 si=0000031c di=00000000 bp=00000000 sp=00006b04 cs=c980 ip=00e5 f=0213 pmm call arg1=1 pmm01: handle=18ae1000 pmm call arg1=0 pmm00: length=1200 handle=18ae1000 flags=2 _malloc zone=0x07f90ed0 size=73728 align=10 ret=0x07f70f90 (detail=0x07f86160) pmm call arg1=1 pmm01: handle=18ae200a pmm call arg1=0 pmm00: length=a000 handle=18ae200a flags=2 _malloc zone=0x07f90ed0 size=655360 align=10 ret=0x07ed0f90 (detail=0x07f860a0) enter handle_16: a=00000180 b=0000ff02 c=00000000 d=00000000 ds=c980 es=c980 ss=de00 si=00000352 di=00000000 bp=00000000 sp=0000f9f6 cs=c980 ip=043b f=0246 Checking rom 0x000ca800 (sig aa55 size 18) Checking rom 0x000c9800 (sig aa55 size 5) Searching bootorder for: /pci@i0cf8/*@3 _malloc zone=0x07f90ed0 size=24 align=10 ret=0x07f85fc0 (detail=0x07f85fe0) Registering bootable: iPXE (PCI 00:03.0) (type:128 prio:104 data:c9800361) Checking rom 0x000ca800 (sig aa55 size 18) Searching bootorder for: /rom@genroms/kvmvapic.bin _malloc zone=0x07f90ed0 size=24 align=10 ret=0x07f85f70 (detail=0x07f85f90) Registering bootable: Legacy option rom (type:129 prio:103 data:ca800003) enter handle_16: a=00000100 b=00000000 c=00000000 d=00000000 ds=0000 es=0000 ss=de00 si=00000000 di=00000000 bp=00000000 sp=0000f9f6 cs=f000 ip=c9e3 f=0242
Press F12 for boot menu.
enter handle_16: a=00000100 b=00000000 c=00000000 d=00000000 ds=0000 es=0000 ss=de00 si=00000000 di=00000000 bp=00000000 sp=0000f9f6 cs=f000 ip=c9e3 f=0242
-
Dustin Brazeau