Index: it8671f_early_serial.c =================================================================== --- it8671f_early_serial.c (Revision 2369) +++ it8671f_early_serial.c (Arbeitskopie) @@ -19,11 +19,73 @@ #include #include "it8671f.h" +/* The base address is 0x3f0, 0x3bd, or 0x370, depending on config bytes. */ +#define SIO_BASE 0x3f0 +#define SIO_INDEX SIO_BASE +#define SIO_DATA SIO_BASE+1 + +/* TODO: These values are actually from the IT8673F datasheet; check if + they're also valid for the IT8671F. */ +#define IT8671F_CONFIG_REG_CC 0x02 /* Configure Control. */ +#define IT8671F_CONFIG_REG_LDN 0x07 /* Logical Device Number. */ +#define IT8671F_CONFIG_REG_CLOCKSEL 0x23 /* Clock Selection. */ +#define IT8671F_CONFIG_REG_SWSUSP 0x24 /* Software Suspend. */ + +#define IT8671F_ADDRESS_PORT 0x279 + +/* Special values used for entering MB PnP mode. The first four bytes of + * each line determine the address port, the last four are data. */ +static const uint8_t init_values[] = { + 0x6a, 0xb5, 0xda, 0xed, /**/ 0xf6, 0xfb, 0x7d, 0xbe, + 0xdf, 0x6f, 0x37, 0x1b, /**/ 0x0d, 0x86, 0xc3, 0x61, + 0xb0, 0x58, 0x2c, 0x16, /**/ 0x8b, 0x45, 0xa2, 0xd1, + 0xe8, 0x74, 0x3a, 0x9d, /**/ 0xce, 0xe7, 0x73, 0x39, +}; + +/* The content of IT8671F_CONFIG_REG_LDN (index 07h) must be set to the + * LDN the register belongs to, before you can access the register. */ +static void it8671f_sio_write(uint8_t ldn, uint8_t index, uint8_t value) +{ + outb(IT8671F_CONFIG_REG_LDN, SIO_BASE); + outb(ldn, SIO_DATA); + outb(index, SIO_BASE); + outb(value, SIO_DATA); +} + +/* Enable the peripheral devices on the IT8671F Super IO chip. */ static void it8671f_enable_serial(device_t dev, unsigned iobase) { - pnp_set_logical_device(dev); - pnp_set_enable(dev, 1); - pnp_set_iobase(dev, PNP_IDX_IO0, iobase); - pnp_set_enable(dev, 1); + uint8_t i; + + /* (1) Enter the configuration state (MB PnP mode). */ + + /* Perform MB PnP setup to put the SIO chip at 0x3f0. */ + /* Base address 0x3f0: 0x86 0x80 0x55 0x55. */ + /* Base address 0x3bd: 0x86 0x80 0x55 0xaa. */ + /* Base address 0x370: 0x86 0x80 0xaa 0x55. */ + outb(0x86, IT8671F_ADDRESS_PORT); + outb(0x80, IT8671F_ADDRESS_PORT); + outb(0x55, IT8671F_ADDRESS_PORT); + outb(0x55, IT8671F_ADDRESS_PORT); + + /* Sequentially write the 32 special values. */ + for (i = 0; i < 32; i++) { + outb(init_values[i], SIO_BASE); + } + + /* (2) Modify the data of configuration registers. */ + + /* Enable parallel port, serial port 1, serial port 2, floppy. */ + it8671f_sio_write(0x00, 0x23, 0x0f); + + /* Activate serial port 1 and 2. */ + it8671f_sio_write(0x01, 0x30, 0x1); + it8671f_sio_write(0x02, 0x30, 0x1); + + /* Select 24MHz CLKIN and clear software suspend mode. */ + it8671f_sio_write(0x00, IT8671F_CONFIG_REG_SWSUSP, 0x00); + + /* (3) Exit the configuration state (MB PnP mode). */ + it8671f_sio_write(0x00, IT8671F_CONFIG_REG_CC, 0x02); } Index: superio.c =================================================================== --- superio.c (Revision 2369) +++ superio.c (Arbeitskopie) @@ -16,12 +16,6 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -// #include -// #include -// #include -// #include -// #include -// #include #include #include #include "chip.h" @@ -38,7 +32,10 @@ conf = dev->chip_info; - switch(dev->path.u.pnp.device) { + switch (dev->path.u.pnp.device) { + case IT8671F_FDC: + /* TODO. */ + break; case IT8671F_SP1: res0 = find_resource(dev, PNP_IDX_IO0); init_uart8250(res0->base, &conf->com1); @@ -63,18 +60,13 @@ .init = init, }; -// TODO. +/* TODO: Find and check datasheet. */ static struct pnp_info pnp_dev_info[] = { -// { &ops, IT8671F_FDC, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x07fa, 0}, }, -// { &ops, IT8671F_PP, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x04f8, 0}, }, + { &ops, IT8671F_FDC, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x07fa, 0}, }, + /* { &ops, IT8671F_PP, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0, { 0x04f8, 0}, }, */ { &ops, IT8671F_SP2, PNP_IO0 | PNP_IRQ0 | PNP_DRQ0 | PNP_DRQ1, { 0x7f8, 0 }, }, { &ops, IT8671F_SP1, PNP_IO0 | PNP_IRQ0, { 0x7f8, 0 }, }, -// { &ops, IT8671F_SWC, PNP_IO0 | PNP_IRQ0, { 0xfff0, 0 }, }, -// { &ops, IT8671F_KBCM, PNP_IRQ0 }, -{ &ops, IT8671F_KBCK, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7f8, 0 }, { 0x7f8, 0x4}, }, -// { &ops, IT8671F_GPIO, PNP_IO0 | PNP_IRQ0, { 0xfff8, 0 } }, -// { &ops, IT8671F_XBUS, PNP_IO0 | PNP_IRQ0, { 0xffe0, 0 } }, -// { &ops, IT8671F_RTC, PNP_IO0 | PNP_IO1, { 0xfffe, 0 }, {0xfffe, 0x4} }, + { &ops, IT8671F_KBCK, PNP_IO0 | PNP_IO1 | PNP_IRQ0, { 0x7f8, 0 }, { 0x7f8, 0x4}, }, }; static void enable_dev(struct device *dev) Index: chip.h =================================================================== --- chip.h (Revision 2369) +++ chip.h (Arbeitskopie) @@ -19,14 +19,6 @@ #ifndef _SUPERIO_ITE_IT8671F #define _SUPERIO_ITE_IT8671F -// TODO: Unused? -// #ifndef SIO_COM1 -// #define SIO_COM1_BASE 0x3F8 -// #endif -// #ifndef SIO_COM2 -// #define SIO_COM2_BASE 0x2F8 -// #endif - #include #include Index: it8671f.h =================================================================== --- it8671f.h (Revision 2369) +++ it8671f.h (Arbeitskopie) @@ -16,20 +16,11 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -// TODO: Untested, cut'n'pasted from some other file so it's probably wrong. -// #define IT8671F_FDC 0x00 /* Floppy */ -// #define IT8671F_PP 0x01 /* Parallel port */ +/* TODO: Find datasheet and check for correct values. */ +#define IT8671F_FDC 0x00 /* Floppy */ +/* #define IT8671F_PP 0x01 */ /* Parallel port */ #define IT8671F_SP2 0x02 /* Com2 */ #define IT8671F_SP1 0x03 /* Com1 */ -// #define IT8671F_SWC 0x04 -// #define IT8671F_KBCM 0x05 /* Mouse */ #define IT8671F_KBCK 0x06 /* Keyboard */ -// #define IT8671F_GPIO 0x07 -// #define IT8671F_ACB 0x08 -// #define IT8671F_FSCM 0x09 -// #define IT8671F_WDT 0x0A -// #define IT8671F_GMP 0x0B -// #define IT8671F_MIDI 0x0C -// #define IT8671F_VLM 0x0D -// #define IT8671F_TMS 0x0E +/* #define IT8671F_FAN 0x09 */