Hi all,

   I try to use Filo.05 to boot my linux on SATA HD.

But it always halt at “Loading kernel...”

Could anybody help me to solve this trouble??

Thanks a lot

Alex

But some error messages occur as below:

malloc_diag: alloc: 232 bytes (3 blocks), free: 16144 bytes                                                           

pci_init: 00:00.0 1039:0761 0600 00                                  

pci_init: 00:01.0 1039:0004 0604 00                                  

pci_init: 00:02.0 1039:0966 0601 00                                   

pci_init: 00:02.5 1039:5513 0101 80                                  

pci_init: 00:03.0 1039:7001 0c03 10                                  

pci_init: 00:03.1 1039:7001 0c03 10                                  

pci_init: 00:04.0 1039:0191 0200 00                                  

pci_init: 00:05.0 1039:1183 0101 85                                  

pci_init: 00:0f.0 1039:7502 0403 00                                  

pci_init: 00:18.0 1022:1100 0600 00                                   

pci_init: 00:18.1 1022:1101 0600 00                                  

pci_init: 00:18.2 1022:1102 0600 00                                  

pci_init: 00:18.3 1022:1103 0600 00                                  

pci_init: 01:00.0 1002:3e50 0300 00                                  

pci_init: 01:00.1 1002:3e70 0380 00                                  

Press <Enter> for default menu.lst (hde1:/boot/grub/grub.conf), or <Esc> for pro                                                                                

mpt... timed out               

menu: hde1:/boot/grub/grub.conf                              

malloc_diag: alloc: 248 bytes (4 blocks), free: 16128 bytes (1 blocks)                                                                      

file_open: dev=hde1, path=/boot/grub/grub.conf                                             

find_ide_controller: found PCI IDE controller 1039:1183 prog_if=0x85                                                                    

find_ide_controller: primary channel: native PCI mode                                                    

find_ide_controller: cmd_base=0x20a0 ctrl_base=0x20c0                                                    

ide_software_reset: Waiting for ide2 to become ready for                                                     

init_drive: Testing for hde                          

init_drive: Probing for hde                          

init_drive: LBA mode, sectors=156301488                                       

init_drive: LBA48 mode, sectors=156301488                                        

init_drive: Init device params... ok                                   

hde: LBA48 80GB: ST380013AS                          

init_drive: Testing for hdf                           

init_drive: Probing for hdf                          

print_status: IDE: status=0x0, err=0x0                                     

init_drive: Testing for hdf                          

init_drive: Probing for hdf                          

print_status: IDE: status=0x0, err=0x0                                     

devopen: Partition 1 start 63 length 153597402                                             

Mounted ext2fs             

malloc_diag: alloc: 232 bytes (3 blocks), free: 16144 bytes (1 b                                                              

boot =====>          

malloc_diag: alloc: 352 bytes (4 blocks), free: 16024 bytes (1 blocks)                                                                     

elf_load open file name =hde1:/boot/vmlinuz-2.6.15-1.2054_FC5smp                                                               

malloc_diag: alloc: 368 bytes (5 blocks), free: 16008 bytes (1 blocks)                                                                      

file_open: dev=hde1, path=/boot/vmlinuz-2.6.15-1.2054_FC5smp                   

devopen: already open

malloc_diag: alloc: 352 bytes (4 blocks), free: 16024 bytes (1 blocks)

elf_load: Not a bootable ELF image

malloc_diag: alloc: 368 bytes (5 blocks), free: 16008 bytes (1 blocks)

file_open: dev=hde1, path=/boot/vmlinuz-2.6.15-1.2054_FC5smp

devopen: already open

malloc_diag: alloc: 352 bytes (4 blocks), free: 16024 bytes (1 blocks)

Found Linux version 2.6.15-1.2054_FC5smp (bhcompile@hs20-bc1-3.build.redhat.com)

 #1 SMP Tue Mar 14 16:05:46 EST 2006 (protocol 0x204) (loadflags 0x1) bzImage.

init_linux_params: Setting up paramters at 0x90000

set_memory_size: 0000000000001000 - 00000000000a0000

set_memory_size: 00000000000c0000 - 00000000000f0000

set_memory_size: 0000000000100000 - 0000000040000000

set_memory_size: ramtop=0x40000000

set_memory_size: ext_mem_k=64512, alt_mem_k=1047552

parse_command_line: original command line: "ro root=LABEL=/ rhgb quiet initrd=/b

oot/initrd-2.6.15-1.2054_FC5smp.img"

parse_command_line: kernel command line at 0x91000

malloc_diag: alloc: 400 bytes (5 blocks), free: 15976 bytes (1 blocks)

parse_command_line: initrd=/boot/initrd-2.6.15-1.2054_FC5smp.img

parse_command_line: kernel command line (26 bytes): "ro root=LABEL=/ rhgb quiet"

load_linux_kernel: offset=0x2000 addr=0x100000 size=0x17c0ac

Loading kernel...