Hi Martin,

Autoport wasn't much use to me since it didn't recognize anything.
However it left behind all kinds of logs like the full lspci output and
stuff like that -> that's why I shared it.

https://github.com/rnplus/test-coreboot-for-asus-p5g41t-m-lx/blob/maste
r/superiodump

https://github.com/rnplus/test-coreboot-for-asus-p5g41t-m-lx/blob/maste
r/superioextradump

This is the output of superiotool using the OEM BIOS.

The SIO is configured for 0x2E.

Greetings,
Renze

On Mon, 2016-03-21 at 13:47 -0600, Martin Roth wrote:

> Hi Renze,
>   I haven't used Autoport, so I can't help much with that - looking
> at the output, I'm not sure this chipset is supported.
>
> On the console:
> Have you run superiotool on your platform with the OEM BIOS?  Can we
> get the output from that?  Is your SIO configured for IO address 0x2E
> or 0x4E?
>
> The hang looks unrelated to the console - It looks like you're
> failing in memory configuration, so I'd keep adding post codes to see
> if you can track down where the actual failure is.  This will
> probably become plain once you get the console working though.
>
> Martin
>
>
> On Fri, Mar 18, 2016 at 4:45 PM, Renze Nicolai <renze@rnplus.nl>
> wrote:
> > Hello everyone,
> >
> > I am trying to port coreboot to the Asus P5G41T-M LX motherboard
> > but I
> > got stuck.
> >
> > This motherboard has:
> >  - Northbridge: Intel G41
> >  - Southbridge: ICH7
> >  - Super IO: w83627dhg
> >
> > I used the Gigabye GA-G41M-ES2L code as base since I think it has
> > the
> > same north- and southbridge. That motherboard has a different Super
> > IO
> > chip though.
> >
> > I tried to make the devicetree.cb file valid and I replaced the
> > superio
> > code in romstage.c with code for the superIO chip on my board. I
> > also
> > tried to set the correct values in the init code for the superio
> > chip
> > (irq routing etc).
> >
> > In romstage.c I added some post codes. The motherboard gets to
> > postcode
> > 0xA6 and then stops.
> >
> > Serial output is not working (cable / connection has been tested
> > from
> > within Linux). Terminal is connected at 115200 baud. No data is
> > received.
> >
> > What I have so far:
> > https://github.com/rnplus/test-coreboot-for-asus-p5g41t-m-lx
> >
> > Logs / info about the board (generated by autoport):
> > https://github.com/rnplus/test-coreboot-for-asus-p5g41t-m-lx/tree/m
> > aste
> > r/autoport_logs
> >
> >
> > It would be nice if someone could point me in the right direction
> > as to
> > what to do next.
> >
> > Thank you!
> >
> > Greetings,
> > Renze Nicolai
> >
> > --
> > coreboot mailing list: coreboot@coreboot.org
> > https://www.coreboot.org/mailman/listinfo/coreboot

--
coreboot mailing list: coreboot@coreboot.org
https://www.coreboot.org/mailman/listinfo/coreboot