Attention is currently required from: Reka Norman.
Reka Norman would like Reka Norman to review this change.
mb/google/brya/var/nivviks: Initialise overridetree
Add an initial overridetree for nivviks based on the pre-proto schematic
and build matrix.
BUG=b:197479026
TEST=abuild -a -x -c max -p none -t google/brya -b nivviks
Signed-off-by: Reka Norman <rekanorman@google.com>
Change-Id: Id3ecd184415a20a3a52da8bb5e60fe2ce0495b44
---
M src/mainboard/google/brya/Kconfig.name
M src/mainboard/google/brya/variants/nivviks/overridetree.cb
2 files changed, 324 insertions(+), 2 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/05/61605/1
diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name
index 0a3b1d9..83c148f 100644
--- a/src/mainboard/google/brya/Kconfig.name
+++ b/src/mainboard/google/brya/Kconfig.name
@@ -80,6 +80,7 @@
config BOARD_GOOGLE_NIVVIKS
bool "-> Nivviks"
select BOARD_GOOGLE_BASEBOARD_NISSA
+ select DRIVERS_INTEL_MIPI_CAMERA
config BOARD_GOOGLE_NEREID
bool "-> Nereid"
diff --git a/src/mainboard/google/brya/variants/nivviks/overridetree.cb b/src/mainboard/google/brya/variants/nivviks/overridetree.cb
index ee86142..ec52b73 100644
--- a/src/mainboard/google/brya/variants/nivviks/overridetree.cb
+++ b/src/mainboard/google/brya/variants/nivviks/overridetree.cb
@@ -1,4 +1,325 @@
+fw_config
+ field DB_USB 0 1
+ option DB_NONE 0
+ option DB_1C_1A 1
+ option DB_1C_LTE 2
+ end
+end
+
chip soc/intel/alderlake
- device domain 0 on
- end
+ register "SaGv" = "SaGv_Enabled"
+
+ register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}"
+ register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}"
+
+ device domain 0 on
+ device ref ipu on
+ chip drivers/intel/mipi_camera
+ register "acpi_uid" = "0x50000"
+ register "acpi_name" = ""IPU0""
+ register "device_type" = "INTEL_ACPI_CAMERA_CIO2"
+
+ register "cio2_num_ports" = "1"
+ register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used
+ register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0""
+ register "cio2_prt[0]" = "2"
+ device generic 0 on end
+ end
+ end
+ device ref i2c1 on
+ chip drivers/i2c/hid
+ register "generic.hid" = ""ELAN6915""
+ register "generic.desc" = ""ELAN Touchscreen""
+ register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)"
+ register "generic.probed" = "1"
+ register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)"
+ register "generic.reset_delay_ms" = "20"
+ register "generic.reset_off_delay_ms" = "2"
+ register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)"
+ register "generic.stop_delay_ms" = "280"
+ register "generic.stop_off_delay_ms" = "2"
+ register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)"
+ register "generic.enable_delay_ms" = "1"
+ register "generic.has_power_resource" = "1"
+ register "generic.disable_gpio_export_in_crs" = "1"
+ register "hid_desc_reg_offset" = "0x01"
+ device i2c 15 on end
+ end
+ end
+ device ref i2c2 on
+ chip drivers/i2c/sx9324
+ register "desc" = ""SAR Proximity Sensor""
+ register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)"
+ register "speed" = "I2C_SPEED_FAST"
+ register "uid" = "1"
+ register "reg_gnrl_ctrl0" = "0x16"
+ register "reg_gnrl_ctrl1" = "0x21"
+ register "reg_afe_ctrl0" = "0x00"
+ register "reg_afe_ctrl1" = "0x10"
+ register "reg_afe_ctrl2" = "0x00"
+ register "reg_afe_ctrl3" = "0x00"
+ register "reg_afe_ctrl4" = "0x07"
+ register "reg_afe_ctrl5" = "0x00"
+ register "reg_afe_ctrl6" = "0x00"
+ register "reg_afe_ctrl7" = "0x07"
+ register "reg_afe_ctrl8" = "0x12"
+ register "reg_afe_ctrl9" = "0x0f"
+ register "reg_prox_ctrl0" = "0x12"
+ register "reg_prox_ctrl1" = "0x12"
+ register "reg_prox_ctrl2" = "0x90"
+ register "reg_prox_ctrl3" = "0x60"
+ register "reg_prox_ctrl4" = "0x0c"
+ register "reg_prox_ctrl5" = "0x12"
+ register "reg_prox_ctrl6" = "0x3c"
+ register "reg_prox_ctrl7" = "0x58"
+ register "reg_adv_ctrl0" = "0x00"
+ register "reg_adv_ctrl1" = "0x00"
+ register "reg_adv_ctrl2" = "0x00"
+ register "reg_adv_ctrl3" = "0x00"
+ register "reg_adv_ctrl4" = "0x00"
+ register "reg_adv_ctrl5" = "0x05"
+ register "reg_adv_ctrl6" = "0x00"
+ register "reg_adv_ctrl7" = "0x00"
+ register "reg_adv_ctrl8" = "0x00"
+ register "reg_adv_ctrl9" = "0x00"
+ register "reg_adv_ctrl10" = "0x5c"
+ register "reg_adv_ctrl11" = "0x52"
+ register "reg_adv_ctrl12" = "0xb5"
+ register "reg_adv_ctrl13" = "0x00"
+ register "reg_adv_ctrl14" = "0x80"
+ register "reg_adv_ctrl15" = "0x0c"
+ register "reg_adv_ctrl16" = "0x38"
+ register "reg_adv_ctrl17" = "0x56"
+ register "reg_adv_ctrl18" = "0x33"
+ register "reg_adv_ctrl19" = "0xf0"
+ register "reg_adv_ctrl20" = "0xf0"
+ device i2c 28 on
+ probe DB_USB DB_1C_LTE
+ end
+ end
+ chip drivers/intel/mipi_camera
+ register "acpi_hid" = ""OVTI5675""
+ register "acpi_uid" = "0"
+ register "acpi_name" = ""CAM0""
+ register "chip_name" = ""Ov 5675 Camera""
+ register "device_type" = "INTEL_ACPI_CAMERA_SENSOR"
+
+ register "ssdb.lanes_used" = "2"
+ register "ssdb.link_used" = "1"
+ register "ssdb.vcm_type" = "0x0C"
+ register "vcm_name" = ""VCM0""
+ register "num_freq_entries" = "1"
+ register "link_freq[0]" = "DEFAULT_LINK_FREQ"
+ register "remote_name" = ""IPU0""
+
+ register "has_power_resource" = "1"
+ #Controls
+ register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3"
+ register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ"
+
+ register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X
+ register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X
+ register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L
+
+ #_ON
+ register "on_seq.ops_cnt" = "5"
+ register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)"
+ register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
+ register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
+ register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)"
+ register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)"
+
+ #_OFF
+ register "off_seq.ops_cnt" = "4"
+ register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)"
+ register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
+ register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
+ register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
+
+ device i2c 36 on end
+ end
+ chip drivers/intel/mipi_camera
+ register "acpi_uid" = "3"
+ register "acpi_name" = ""VCM0""
+ register "chip_name" = ""DW AF DAC""
+ register "device_type" = "INTEL_ACPI_CAMERA_VCM"
+
+ register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC""
+ register "vcm_compat" = ""dongwoon,dw9714""
+
+ device i2c 0C on end
+ end
+ chip drivers/intel/mipi_camera
+ register "acpi_hid" = "ACPI_DT_NAMESPACE_HID"
+ register "acpi_uid" = "1"
+ register "acpi_name" = ""NVM0""
+ register "chip_name" = ""GT24C08""
+ register "device_type" = "INTEL_ACPI_CAMERA_NVM"
+
+ register "pr0" = ""\\_SB.PCI0.I2C2.CAM0.PRIC""
+
+ register "nvm_size" = "0x2000"
+ register "nvm_pagesize" = "1"
+ register "nvm_readonly" = "1"
+ register "nvm_width" = "0x10"
+ register "nvm_compat" = ""atmel,24c08""
+
+ device i2c 50 on end
+ end
+ end
+ device ref i2c3 on
+ chip drivers/i2c/nau8825
+ register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)"
+ register "jkdet_enable" = "1"
+ register "jkdet_pull_enable" = "0"
+ register "jkdet_polarity" = "1" # ActiveLow
+ register "vref_impedance" = "2" # 125kOhm
+ register "micbias_voltage" = "6" # 2.754
+ register "sar_threshold_num" = "4"
+ register "sar_threshold[0]" = "0x0c"
+ register "sar_threshold[1]" = "0x1c"
+ register "sar_threshold[2]" = "0x38"
+ register "sar_threshold[3]" = "0x60"
+ register "sar_hysteresis" = "1"
+ register "sar_voltage" = "0" # VDDA
+ register "sar_compare_time" = "0" # 500ns
+ register "sar_sampling_time" = "0" # 2us
+ register "short_key_debounce" = "2" # 100ms
+ register "jack_insert_debounce" = "7" # 512ms
+ register "jack_eject_debounce" = "7" # 512ms
+ device i2c 1a on end
+ end
+ end
+ device ref i2c5 on
+ chip drivers/i2c/generic
+ register "hid" = ""ELAN0000""
+ register "desc" = ""ELAN Touchpad""
+ register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)"
+ register "wake" = "GPE0_DW2_14"
+ register "probed" = "1"
+ device i2c 15 on end
+ end
+ end
+ device ref hda on
+ chip drivers/generic/max98357a
+ register "hid" = ""MX98360A""
+ register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)"
+ register "sdmode_delay" = "5"
+ device generic 0 on end
+ end
+ end
+ device ref pch_espi on
+ chip ec/google/chromeec
+ use conn0 as mux_conn[0]
+ use conn1 as mux_conn[1]
+ device pnp 0c09.0 on end
+ end
+ end
+ device ref pmc hidden
+ chip drivers/intel/pmc_mux
+ device generic 0 on
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port1 as usb2_port
+ use tcss_usb3_port1 as usb3_port
+ device generic 0 alias conn0 on end
+ end
+ chip drivers/intel/pmc_mux/conn
+ use usb2_port2 as usb2_port
+ use tcss_usb3_port2 as usb3_port
+ device generic 1 alias conn1 on end
+ end
+ end
+ end
+ end
+ device ref tcss_xhci on
+ chip drivers/usb/acpi
+ device ref tcss_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "group" = "ACPI_PLD_GROUP(1, 1)"
+ device ref tcss_usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "group" = "ACPI_PLD_GROUP(2, 1)"
+ device ref tcss_usb3_port2 on end
+ end
+ end
+ end
+ end
+ device ref xhci on
+ chip drivers/usb/acpi
+ device ref xhci_root_hub on
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C0 (MLB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "group" = "ACPI_PLD_GROUP(1, 1)"
+ device ref usb2_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-C Port C1 (DB)""
+ register "type" = "UPC_TYPE_C_USB2_SS_SWITCH"
+ register "group" = "ACPI_PLD_GROUP(2, 1)"
+ device ref usb2_port2 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_A"
+ register "group" = "ACPI_PLD_GROUP(3, 1)"
+ device ref usb2_port3 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_A"
+ register "group" = "ACPI_PLD_GROUP(4, 1)"
+ device ref usb2_port4 on
+ probe DB_USB DB_1C_1A
+ end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port4 on
+ probe DB_USB DB_1C_LTE
+ end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Camera""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb2_port6 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Bluetooth""
+ register "type" = "UPC_TYPE_INTERNAL"
+ register "reset_gpio" =
+ "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)"
+ device ref usb2_port8 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 Type-A Port A0 (MLB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "group" = "ACPI_PLD_GROUP(3, 1)"
+ device ref usb3_port1 on end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB2 Type-A Port A1 (DB)""
+ register "type" = "UPC_TYPE_USB3_A"
+ register "group" = "ACPI_PLD_GROUP(4, 1)"
+ device ref usb3_port2 on
+ probe DB_USB DB_1C_1A
+ end
+ end
+ chip drivers/usb/acpi
+ register "desc" = ""USB3 WWAN""
+ register "type" = "UPC_TYPE_INTERNAL"
+ device ref usb3_port2 on
+ probe DB_USB DB_1C_LTE
+ end
+ end
+ end
+ end
+ end
+ end
end
To view, visit change 61605. To unsubscribe, or for help writing mail filters, visit settings.