Matthew Garrett has uploaded this change for review.
Add a doc describing an ACPI device for controlling platform radios.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Change-Id: I94dc058825cb147aca0d007d68885d4bfbe580a8
---
M Documentation/acpi/index.md
A Documentation/acpi/rfkill.md
M src/arch/x86/include/arch/acpi.h
3 files changed, 111 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/91/37991/1
diff --git a/Documentation/acpi/index.md b/Documentation/acpi/index.md
index 8add8db..d10bca5 100644
--- a/Documentation/acpi/index.md
+++ b/Documentation/acpi/index.md
@@ -9,3 +9,7 @@
## devicetree
- [Adding devices to a device tree](devicetree.md)
+
+## Radio device control
+
+- [Exposing an ACPI device for controlling radios](rfkill.md)
diff --git a/Documentation/acpi/rfkill.md b/Documentation/acpi/rfkill.md
new file mode 100644
index 0000000..ef54f16
--- /dev/null
+++ b/Documentation/acpi/rfkill.md
@@ -0,0 +1,106 @@
+# Coreboot platform rfkill control
+
+## Introduction
+
+Many devices support platform-level control over integrated radio devices
+such as wifi or bluetooth cards. However, the ACPI specification provides
+no generic mechanism for operating systems to interact with these platform
+interfaces. This has led to a proliferation of vendor-specific control
+mechanisms. Coreboot ports to existing platforms tend to mimic those
+interfaces and make use of existing drivers, but this doesn't solve the
+problem for devices where coreboot is the primary firmware implementation.
+
+This specification defines an ACPI device that exposes an interface for
+controlling any radios defined by the platform. It is intended to allow for
+generic OS drivers to be written which will then work on any coreboot
+platform that implements this specification.
+
+## Device specification
+
+The coreboot rfkill device must be declared with a _HID of "BOOT0001".
+It must implement the following ACPI methods:
+
+### DEVS
+
+This method provides a list of the supported radios whose state can be
+controlledvia this device. It takes no arguments and returns a single
+integer. The integer is a bitmask of radio types supported by the device,
+defined as follows:
+
+| Bit | Radio type |
+|-----|---------------|
+| 0 | Wifi |
+| 1 | Bluetooth |
+| 2 | Ultra-Wideband|
+| 3 | WiMax |
+| 4 | WWAN |
+| 5 | GPS |
+| 6 | FM |
+| 7 | NFC |
+
+### SSTA
+
+This defines the mutable ("soft") state of all radios in the system. This
+method takes no arguments and returns a single integer. The integer is a
+bitmask representing radio state using the same values as defined in
+DEVS. If a bit is 1 then the radio is enabled. If a bit is 0 then the radio
+is not present. If a bit is not set in the value returned by the DEVS method
+then the meaning of the bit returned by SSTA is undefined. The state
+returned by SSTA can be overridden by the CNTL method.
+
+### HSTA
+
+This defines the immutable ("hard") state of all radios in the system. This
+method takes no arguments and returns a single integer. The integer is a
+bitmask representing radio state using the same values as defined in
+DEVS. If a bit is 1 then the radio is enabled. If a bit is 0 then the radio
+is disabled. If a bit is not set in the value returned by the DEVS method
+then the meaning of the bit returned by HSTA is undefined. The state
+returned by HSTA cannot be overridden by the CNTL method.
+
+### CNTL
+
+This method takes a single integer as an argument and returns nothing. The
+argument is a bitmask representing radio state using the same values as
+defined in DEVS. If a bit is 1 then the platform should enable the
+corresponding radio. If a bit is 0 then the platform should disable the
+corresponding radio. This method only alters the soft radio state, not the
+hard radio state.
+
+### Notifications
+
+The platform will send a Notify with a value of 0x80 if the state is updated
+via any mechanism other than an OS request. The OS should then re-evaluate
+the state by calling SSTA and HSTA.
+
+## Implementation design
+
+Two types of blocking are defined - "soft" and "hard". Soft state can be
+overridden on request by the OS, for example in response to a hotkey
+press. Hard state cannot be overridden by the OS, and should correspond to
+cases where some external interface has requested that radios be disabled
+(for example, a physical switch on the side of the device). Hard and soft
+state should be tracked independently - for instance, if a radio is
+currently enabled and then disabled via a physical switch being moved, the
+state returned by SSTA should still indicate that the radio is enabled while
+the state returned by HSTA should indicate that the radio is disabled. If
+the OS then requests that the radio be disabled via the CNTL method, SSTA
+and HSTA should now both indicate that the radio is disabled. If the
+physical switch is now switched back, HSTA should indicate that the radio is
+enabled but SSTA should still indicate that the radio is disabled. Only when
+the OS requests that the radio be enabled via CNTL should the radio be
+re-enabled.
+
+If the platform alters the radio state (in response to any form of policy
+decision or in response to a physical switch), it should update the soft
+block state (if the OS can override this decision) or the hard block state
+(if the OS cannot override this decision) and then call Notify on the device
+with an argument of 0x80.
+
+If the platform provides more than one radio of a given type, it should
+implement an additional rfkill device. Each radio should only be represented
+in a single device.
+
+If an rfkill device should be explicitly tied to a radio device, then the
+radio should be exposed in the ACPI device heirarchy and an rfkill device
+that controls only that radio implemented as a child of that device.
diff --git a/src/arch/x86/include/arch/acpi.h b/src/arch/x86/include/arch/acpi.h
index 68475c1..e87df04 100644
--- a/src/arch/x86/include/arch/acpi.h
+++ b/src/arch/x86/include/arch/acpi.h
@@ -64,6 +64,7 @@
/* List of ACPI HID that use the coreboot ACPI ID */
enum coreboot_acpi_ids {
COREBOOT_ACPI_ID_CBTABLE = 0x0000, /* BOOT0000 */
+ COREBOOT_ACPI_ID_RFKILL = 0x0001, /* BOOT0001 */
COREBOOT_ACPI_ID_MAX = 0xFFFF, /* BOOTFFFF */
};
To view, visit change 37991. To unsubscribe, or for help writing mail filters, visit settings.