Furquan Shaikh uploaded patch set #11 to this change.
mb/google/volteer/var/volteer: Use auto-generated Makefile.inc using gen_part_id.go
This change adds mem_list_variant.txt that contains the list of
memory parts used by volteer and Makefile.inc generated by
gen_part_id.go using mem_list_variant.txt.
In the final change of the series, all volteer variants will be
switched from using the current SPDs to new auto-generated SPDs.
Differences in auto-generated SPD from current SPD are as follows:
Part: K4U6E3S4AA-MGCL
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
Part: K4UBE3D4AA-MGCL
Byte# Current New Explanation
6 0xB5 0xB4 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
Part: H9HCNNNBKMMLXR-NEE
Byte# Current New Explanation
6 0x95 0x94 Signal loading is not used by
MRC. Set bits 1:0 to 00.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
19 0x0F 0xFF As per JEDEC spec, tckMax should be
100ns. So, value should be 0xff as
per datasheet.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. tckMin is
calculated as (1/4267)*2 which comes
out to be 0.46871. Some datasheets
round this down to 0.468 and others
round it up to 0.469. JEDEC spec uses
0.468. As per that, this value comes
out to be 0xE0.
Part: H9HCNNNFAMMLXR-NEE
Byte# Current New Explanation
4 0x15 0x16 As per datasheet, density is 16Gb per
logical channel. So value should be 0x16.
6 0xF9 0xB8 This device has 4 logical dies
instead of 8. Also, signal loading is
not used by MRC.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
20,21, 0x92,0x55, 0x12,0x29, As per datasheet, part supports CAS
22 0x00 0x15 latencies 6,10,16,22,26,32,36,40. So value
should be 0x12,0x29,0x15.
24 0x8C 0x96 taa is .468ns * CAS-40 which results
in byte 24 being 0x96 as per datasheet.
29,30 0xE0,0x0B 0xC0,0x08 As per datasheet, this corresponds to
280ns in MTB units which is 0x08C0.
31,32 0xF0,0x05 0x60,0x04 As per datasheet, this corresponds to
140ns in MTB units which is 0x04C0.
123 0x00 0xE2 Fine offset for taa. Expected value
is 0xE2 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. tckMin is
calculated as (1/4267)*2 which comes
out to be 0.46871. Some datasheets
round this down to 0.468 and others
round it up to 0.469. JEDEC spec uses
0.468. As per that, this value comes
out to be 0xE0.
Part: MT53E1G32D2NP-046 WT:A
Byte# Current New Explanation
4 0x15 0x16 As per datasheet, density is 16Gb per
logical channel. So value should be 0x16.
5 0x21 0x29 As per datasheet, this part has 17row
address bits and 10column address
bits. This results in 0x29.
6 0xB5 0x94 This device has 2 logical dies. Also,
MRC does not use signal loading.
16 0x48 0x00 Signal loading is not used by
MRC. Set to 0x00.
12 0x0A 0x02 As per datasheet, this is 1rank and
16-bit wide channel. So, value should
be 0x02.
21,22 0x55,0x00 0x54,0x05 As per datasheet, part supports CAS
latencies 20,24,28,32,36. So value
should be 0x54, 0x05.
24 0x8C 0x87 taa is .468ns * CAS-36 which results
in byte 24 being 0x87 as per datasheet.
29,30 0xC0,0x08 0xE0,0x0B As per datasheet, this corresponds to
380ns in MTB units which is 0x0BE0.
31,32 0x60,0x04 0xF0,0x05 As per datasheet, this corresponds to
190ns in MTB units which is 0x05F0.
123 0x00 0xE5 Fine offset for taa. Expected value
is 0xE5 as per datasheet.
124 0x7F 0x00 Fine offset for tckMax. Expected
value is 0x00 as per datasheet.
125 0xE1 0xE0 Fine offset for tckMin. As per
datasheet tckMin is 0.468ns. So, this
comes out to be 0xE0.
BUG=b:147321551,b:155423877
Change-Id: I3998b2cd91020130bacf371fce9b0d307304acbe
Signed-off-by: Furquan Shaikh <furquan@google.com>
---
A src/mainboard/google/volteer/variants/volteer/memory/Makefile.inc
A src/mainboard/google/volteer/variants/volteer/memory/dram_id.generated.txt
A src/mainboard/google/volteer/variants/volteer/memory/mem_list_variant.txt
3 files changed, 20 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/17/41617/11
To view, visit change 41617. To unsubscribe, or for help writing mail filters, visit settings.